SHOULDER ZTACV_MT

SHOULDER ELECTRONICS CO., LTD.
CERAMIC RESONATOR Data Sheet
PRODUCT 产 品:
CERAMIC RESONATOR
MODEL NO 型 号: ZTACV....MT
PREPARED 编 制:
Fengyu
CHECKED 审 核:
York
APPROVED 批 准:
DATE
Http://www.shoulder.cn
日 期:
2007-01-25
SHOULDER ELECTRONICS CO., LTD.
1.
Scope
The specification is fit for ceramic resonator 8.00-13.00MHz.
2. Part NO: ZTACV … MT
3.
Electrical Characteristics
No.
Item
Characteristics
3-1
Oscillate Frequency (MHz)
8.00-13.00
3.2
Frequency Tolerance max
±0.5%
3.3
Resonant Impedance max (Ω)
30
3.4
Built – in Capacitance (PF)
--
3.5
Insulate Resistance min (MΩ)
100
3.6
Withstanding Voltage D.C (V)
3.7
Voltage
1 D.C Voltage max V
2 Input Voltage max V
6
15Vp-p
3.8
Temp characteristics of Oscillate frequency max
±0.3%
3.9
Operating Temp Range
3.10
4.
100
Storage Temp (
max 5 sec
-20 ~ +80
)
-55 ~ +85
Test Circuit
5V
IC
IC
Output
1Mohm
C1
X
C2
IC: 1/6TC4069UBPx2
X: Ceramic Resonator
C1C2: 30PF
5.
Dimension
6. Physical and Environmental Characteristics
No
Item
6.1
Humidity
6.2
Vibration
6.3
Mechanical
Shock
Condition of Test
Performance
Requirements
It shall fulfill the
Keep the resonator at 40 2 and
90-95% RH for 96
4 hours. Then specifications in Table
release the resonator into the room 1.
condition for 1 hour prior to the
measurement.
Subject the resonator to vibration for 2 It shall fulfill the
hours each in x,y and z axis with the specifications in Table
amplitude of 1.5mm, the frequency shall 1.
be varied uniformly between the limits of
10-55Hz
Drop the resonator randomly onto a It shall fulfill the
concrete floor from the height of
specifications in Table
100 cm 3 times.
1.
6.4
Soldering
Test
Passed through the re-flow oven under
the following condition and left at room
temperature
for
1
hour
before
measurement.
Temperature
at
surface of the Time
substrate
Preheat 150 5
60 10 sec.
Peak 240 5
10 3 sec.
Dip the resonator terminals into the
solder bath at 230 5 for 3 0.5 sec.
6.5
Solder
Ability
6.6
High
Temperature
Exposure
6.7
Low
Temperature
6.8
Temperature
Cycling
It shall fulfill the
specifications in Table
1.
More than 95% of the
terminal surface shall
be covered.
Subject the resonator to 80 5
for 96 It shall fulfill the
4 hours. Then release the resonator specifications in Table
into the room conditions for 1 hour prior 1.
to the measurement.
Subject the resonator to –20 5 for 96 It shall fulfill the
4 hours. Then release the resonator specifications in Table
into the room conditions for 1 hour prior 1.
to the measurement.
Subject the resonator to –20
for 30 It shall fulfill the
minutes followed by a high temperature specifications in Table
of 85
for 30 min. Cycling shall be 1.
repeated 5 times with a transfer time of
15 second at the room condition for 1
hour prior to the measurement.
TABLE1
Item
7.
Specification
Oscillation Frequency Change
F/Fo
0.3% max
Resonant Impedance
Ro
10 Ohm
8. Packing
Tape Dimension (mm)
A
0.2
MG
MT
MX
B
0.2
C
0.3
D
0.1
3.8
7.8
16.0
7.5
5.0
4.4
12.0
5.5
3.4
4.0
12.0
5.5
E
0.1
F
0.1
G
0.1
H
0.1
ØJ
0.1
ØN
0.1
M
max
R
max
K
0.2
T
0.1
2.1
1.75
Standard Package: 1Kpcs / reel
8.0
4.0
2.0
1.5
1.6
10
0.3
1.8
1.3
0.3