SHOULDER ZTACS_MX

SHOULDER ELECTRONICS CO., LTD.
CERAMIC RESONATOR Data Sheet
PRODUCT 产 品:
CERAMIC RESONATOR
MODEL NO 型 号: ZTACS....MX
PREPARED 编 制:
Fengyu
CHECKED 审 核:
York
APPROVED 批 准:
DATE
Http://www.shoulder.cn
日 期:
2007-01-25
SHOULDER ELECTRONICS CO., LTD.
1.
Scope
The specification is fit for ceramic resonator 13.01-50.00MHz.
2. Part NO: ZTACS … MX
3. Electrical Characteristics
No.
Item
Characteristics
3-1
Oscillate Frequency (MHz)
13.01-50.00
3.2
Frequency Tolerance max
±0.5%
3.3
Resonant Impedance max (Ω)
40
3.4
Built – in Capacitance (PF)
--
3.5
Insulate Resistance min (MΩ)
100
3.6
Withstanding Voltage D.C (V)
3.7
Voltage
1 D.C Voltage max V
2 Input Voltage max V
6
15Vp-p
3.8
Temp characteristics of Oscillate frequency max
±0.3%
3.9
Operating Temp Range
3.10
4.
Storage Temp (
100
max 5 sec
-20 ~ +80
)
-55 ~ +85
Test Circuit
5V
IC
Output
1M
C1
X
IC
C2
IC:1/6TC74HCU04x2
C1C2:30PF(13.01-20.00MHz)
15PF(20.01-25.99MHz)
5PF (26.00-40.00MHz)
X: Ceramic Resonator
5.
Dimension
6. Physical and Environmental Characteristics
No
Item
6.1
Humidity
6.2
Vibration
6.3
Mechanical
Shock
Condition of Test
Performance
Requirements
It shall fulfill the
Keep the resonator at 40 2 and
90-95% RH for 96
4 hours. Then specifications in Table
release the resonator into the room 1.
condition for 1 hour prior to the
measurement.
Subject the resonator to vibration for 2 It shall fulfill the
hours each n
i x,y and z axis with the specifications in Table
amplitude of 1.5mm, the frequency shall 1.
be varied uniformly between the limits of
10-55Hz
Drop the resonator randomly onto a It shall fulfill the
concrete floor from the height of
specifications in Table
100 cm 3 times.
1.
6.4
Soldering
Test
6.5
Solder
Ability
6.6
High
Temperature
Exposure
6.7
Low
Temperature
6.8
Temperature
Cycling
Passed through the re-flow oven under
the following condition and left at room
temperature
for
1
hour
before
measurement.
Temperature at
surface of the
Time
substrate
Preheat 150 5
60 10 sec.
Peak 240 5
10 3 sec.
Dip the resonator terminals into the
solder bath at 230 5 for 3 0.5 sec.
It shall fulfill the
specifications in Table
1.
More than 95% of the
terminal surface shall
be covered.
Subject the resonator to 80 5
for 96 It shall fulfill the
4 hours. Then release the resonator specifications in Table
into the room conditions for 1 hour prior 1.
to the measurement.
Subject the resonator to –20 5 for 96 It shall fulfill the
4 hours. Then release the resonator specifications in Table
into the room conditions for 1 hour prior 1.
to the measurement.
Subject the resonator to –20
for 30 It shall fulfill the
minutes followed by a high temperature specifications in Table
of 85
for 30 min. Cycling shall be 1.
repeated 5 times with a transfer time of
15 second at the room condition for 1
hour prior to the measurement.
TABLE1
Item
7.
Specification
Oscillation Frequency Change
F/Fo
0.3% max
Resonant Impedance
Ro
10 Ohm
8. Packing
Tape Dimension (mm)
A
0.2
MG
MT
MX
B
0.2
C
0.3
D
0.1
3.8
7.8
16.0
7.5
5.0
4.4
12.0
5.5
3.4
4.0
12.0
5.5
E
0.1
F
0.1
G
0.1
H
0.1
ØJ
0.1
ØN
0.1
M
max
R
max
K
0.2
T
0.1
2.1
1.75
Standard Package: 1Kpcs / reel
8.0
4.0
2.0
1.5
1.6
10
0.3
1.8
1.3
0.3