SOURCE B-13-15-622-TPM-SFC4-60

622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Features
• Coaxial single mode single fiber package with optional
SC/FC/ST/MU connector
• Wavelength Tx 1310 nm/Rx 1550 nm
• SONET OC-12 SDH STM-4 Compliant
• Single +5V/+3.3V Power Supply
• PECL/LVPECL Differential Inputs and Outputs
• Wave Solderable and Aqueous Washable
• Class 1 Laser Int. Safety Standard IEC 825 Compliant
• Uncooled Laser diode with MQW structure
• Complies with Telcordia (Bellcore) GR-468-CORE
• Optical Isolation > 30 dB
• Cross talk < -33 dB
• Optical Return Loss >14 dB
Absolute Maximum Rating
Parameter
Symbol
Min.
Max.
Unit
Note
Vcc
0
6
V
B-13/15-622-TPM-SXX4(A)-60
Power Supply Voltage (3.3V)
Vcc
0
3.6
V
B-13/15-622-TPM3-SXX4(A)-60
Output Current
Iout
0
30
mA
Power Supply Voltage (5V)
Soldering Temperature
-
-
260
ºC
Tstg
-40
85
ºC
Symbol
Min.
Typ.
Max.
Unit
Vcc
4.75
5
5.25
V
Power Supply Voltage (3.3V)
Vcc
3.1
3.3
3.5
V
Operating Temperature1
Topr
0
-
70
ºC
Operating Temperature1
Topr
-40
-
85
ºC
-
622
-
Mbps
Storage Temperature
10 seconds on leads only
Recommended Operating Condition
Parameter
Power Supply Voltage (5V)
Data Rate
Note 1 : Please refer to ordering information
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Transmitter Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Optical Transmit Power
Po
-3
-
+2
dBm
Output Center Wavelength
λ
1260
1310
1360
nm
Output Spectrum Width
∆λ
-
-
2.5
nm
Extinction Ratio
ER
8.2
-
-
dB
Notes
Optical
Output Eye
Output power is coupled into a 9/125 µm
single mode fiber
RMS(σ)
Compliant with Bellcore GR-253-CORE and ITU recommendation G957
Optical Rise Time
tr
-
-
1.2
ns
10% to 90% Values
Optical Fall Time
tf
-
-
1.2
ns
10% to 90% Values
30
-
-
dB
Tx: 1310 nm/ Rx: 1550 nm
Optical Isolation
Optical Return Loss
14
-
-
dB
RIN
-
-
-120
dB/Hz
TJ
-
-
0.55
ns
Measured with 223-1 PRBS with 72 ones and
72 zeros.
Symbol
Min
Typical
Max
Unit
Notes
Power Supply Current
ICC
-
-
180
mA
Data Input Current-Low
IIL
-350
-
-
µA
Data Input Current-High
IIH
-
-
350
µA
Relative Intensity Noise
Total Jitter
Transmitter Specifications
Parameter
Electrical
Differential Input Voltage
VIH-VIL
300
-
-
mV
Data Input Voltage-Low
VIL-VCC
-2.0
-
-1.58
V
Data Input Voltage-High
VIH-VCC
-1.1
-
-0.74
V
LUMINENTOIC.COM
Maximum current is specified at
Vcc= Maximum @ maximum temperature
These inputs are compatible with 10K, 10KH
and 100K ECL and PECL inputs
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Receiver Specifications
Parameter
Symbol
Min
Typical
Max
Unit
Notes
-
-
-
-28
dBm
Measured with 223-1 PRBS with 72 ones and
72 zeros. (ITU-T recommendation G.958)
Maximum Input Power
Pin
-3
-
-
dBm
Signal Detect-Asserted
Pa
-
-
-28
dBm
Measured on transition: low to high
Signal Detect-Deasserted
Pd
-40
-
-
dBm
Measured on transition: high to low
-
3.0
-
dB
-
-
-33
dB
1480
-
1600
nm
Symbol
Min
Typical
Max
Unit
Notes
ICC
-
-
100
mA
The current excludes the output load current
Data Output Voltage-Low
VOL -Vcc
-1.9
-
-1.6
V
Data Output Voltage-High
VOH- Vcc
-1.1
-
-0.8
V
Signal Detect Output Voltage-Low
VSDL-Vcc
-1.9
-
-1.6
V
Signal Detect Output Voltage-High VSDH- Vcc
-1.1
-
-0.8
V
Optical
Sensitivity
Signal Detect-Hysteresis
Cross Talk
-
Wavelength of Operation
Receiver Specifications
Parameter
Electrical
Power Supply Current
LUMINENTOIC.COM
These outputs are compatible with 10K,
10KH and 100KECL and PECL outputs.
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Connection Diagram
1. (Rx GND)
2. (Rx +)
3. (Rx-)
4. (SD)
5. (Rx Vcc)
6. (Tx Vcc)
7. (TD-)
8. (TD+)
9. (Tx GND)
NC
Top View
NC
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data in
Transmitter Signal Ground
PIN
Symbol
1
RxGND
2
RD+
See recommended circuit schematic
3
RD-
See recommended circuit schematic
4
SD
Active high on this indicates a received optical signal
5
RxVcc
6
TxVcc
DC power for the transmitter section
7
TD-
See recommended circuit schematic
TD+
See recommended circuit schematic
8
Warnings
9
LUMINENTOIC.COM
Notes
Directly connect this pin to the receiver ground plane
DC power for the receiver section
TxGND
Directly connect this pin to the transmitter ground plane
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Recommended Circuit Schematic
Tx Vcc
C5
Rx Vcc
7 6 5
9 8
R1
4 3 2
1
R3
R9
R5
C6
R7
RD +
TD +
RD -
TD -
Tx Vcc
SD
Rx Vcc
R2
R4
Notes +3.3V:
R1=R3=R5=R7=R9=130
R2=R4=R6=R8=R10=82
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
No internal
connection
No internal
connection
Transceiver
Top view
R10
R6
R8
L1
Notes +5V:
R1=R3=R5=R7=R9=82
R2=R4=R6=R8=R10=130
C1=C2=C3=C5=C6=0.1F
C4=10F
L1=L2=1H
Vcc
C3
C1
L2
C4
C2
Rx Vcc
Tx Vcc
The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals.
The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc/ Tx Vcc
A GND plane under the module is required for good EMI and sensitivity performance.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Package Diagram
Front View
Top View
Units: mm
max
Rear View
Side View
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS830-Jul2105
rev. A.1
622 Mbps Bi-directional Single Fiber Transceiver
B-13/15-622-TPM(3)-SXX4(A)-60
Ordering Information
Available Options: B-13/15-622-TPM-SSC4(A)-60
B-13/15-622-TPM-SST4(A)-60
B-13/15-622-TPM-SFC4(A)-60
B-13/15-622-TPM-SMU4(A)-60
B-13/15-622-TPM3-SSC4(A)-60
B-13/15-622-TPM3-SST4(A)-60
B-13/15-622-TPM3-SFC4(A)-60
B-13/15-622-TPM3-SMU4(A)-60
Part numbering Definition:
B - 13/15 - 622 - TPM(3)
- S XX
TxPower
Temperature -60
• Wavelength
Tx Wavelength=1310nm
Rx Wavelength=1550nm
• Communication protocol
(622 Mbps)
• TPM = +5V Transceiver
TPM3 = +3.3 V Transceiver
• Single mode fiber
• Connector options
SC/FC/ST/MU
• Tx Power range
4= -3 to +2 dBm
• Temperature
Blank = Commercial Temperature (0 to 70℃)
A = Industrial Temperatuure (-40 to 85℃)
• -60 : fiber length = 660mm ±20mm
Warnings
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notice
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS830-Jul2105
rev. A.1