155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Features • Duplex SC Single Mode Transceiver • Industry Standard 1x9 Footprint • Intermediate Reach SONET OC-3 SDH STM-1 Compliant • Single 5V or Power Supply • PECL Differential Inputs and Outputs • Wave Solderable and Aqueous Washable • LED Multisourced 1x9 Transceiver Interchangeable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser Diode with MQW Structure • Complies with Telcordia (Bellcore) GR-468-CORE • Black case 10.4 mm • SD PECL level • ATM 155 Mbps Links Application • SONET/SDH Equipment Interconnect Application Absolute Maximum Rating Parameter Symbol Min. Max. Unit Power Supply Voltage Vcc 0 6.0 V Output Current Iout 0 30 mA Soldering Temperature - - 260 ºC Operating Temperature Topr -25 70 ºC Storage Temperature Tstg -40 85 ºC Note 10 seconds on leads only Recommended Operating Condition Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 4.75 5.0 5.25 V Operating Temperature (Case) Topr -25 - 70 ºC - 155 - Mbps Data Rate Transmitter Specifications, (-25<Topr<70ºC, 4.75V<VCC<5.25V) Parameter Symbol Min Typical Max Unit Notes Po -5 - 0 dBm output power is coupled into a 9/125 µm single mode fiber λ 1263 1310 1360 nm 3 nm - dB Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width ∆λ Extinction Ratio ER 10 - Output Pulse Mask Compliant with FDDI SMF-PMD1 Output Eye Compliant with ITU-T recommendation G.957 RMS(σ) Optical Rise Time tr - - 2 ns 10% to 90% Values Optical Fall Time tf - - 2 ns 10% to 90% Values Relative Intensity Noise RIN - - -116 dB/Hz Total Jitter TJt - - 1.2 ns LUMINENTOIC.COM Measured with 223-1 PRBS with 72 ones and 72 zeros. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1011-AUG1204 rev. A.0 155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Transmitter Specifications, (-25<Topr<70ºC,4.75V<VCC<5.25V) Parameter Symbol Min Typical Max Unit Power Supply Current ICC - - 150 mA Data Input Current-Low IIL -350 - - µA Notes Electrical Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications, (-25<Topr<70ºC,4.75V<VCC<5.25V) Parameter Symbol Min Typical Max Unit Notes - - - -35 dBm measured with 223-1 PRBS with 72 ones and 72 zeros. Maximum Input Power Pin 0 - - dBm Signal Detect-Asserted Pa - - -35 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -47 - - dBm Measured on transition: high to low 1.0 - 4.0 dB 1100 - 1600 nm Optical Sensitivity Signal Detect-Hysteresis Wavelength of Operation Receiver Specifications, (-25<Topr<70ºC,4.75V<VCC<5.25V) Parameter Symbol Min Typical Max Unit ICC - - 100 mA Data Output Voltage-Low VOL -Vcc -2 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect Output Voltage-Low VSDL-Vcc -2 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V Notes Electrical Power Supply Current LUMINENTOIC.COM The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and LVPECL outputs. PECL SD Output 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1011-AUG1204 rev. A.0 155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Connection Diagram 1. (Rx GND) 2. (RD +) 3. (RD-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TD-) 8. (TD+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol Notes 1 RxGND Directly connect this pin to the receiver ground plane 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD Active high on this indicates a received optical signal 5 RxVcc +5V dc power for the receiver section 6 TxVcc +5V dc power for the transmitter section 7 TD- See recommended circuit schematic TD+ See recommended circuit schematic 8 Warnings 9 TxGND Directly connect this pin to the transmitter ground plane Legal Notice LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1011-AUG1204 rev. A.0 155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Recommended Circuit Schematic Tx Vcc C5 Rx Vcc 7 6 5 4 3 2 9 8 R1 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 No internal connection No internal connection Transceiver Top view R10 R6 R8 L1 Vcc Notes +5V: R1=R3=R5=R7=R9=82! R2=R4=R6=R8=R10=130! C1=C2=C3=C5=C6=0.1"F C4=10"F L1=L2=1"H C3 Rx Vcc C1 L2 C4 Tx Vcc C2 The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1011-AUG1204 rev. A.0 155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Package Diagram SC Transceiver Assembly 10.4mm LUMINENTOIC.COM Top View Front View Side View Rear View 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1011-AUG1204 rev. A.0 155 Mbps Single Mode Transceiver C-13-155-T-SSC5-06 Ordering Information C - 13 - 155 - T - S SC 5 -06 • Wavelength = 1310 nm • Communication protocol (155 Mbps) • T = 5V Transceiver , FP • Single mode fiber • Connector options(SC) • Long Reach • Temperaturerange and package -06 = -25 to 70ºC Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1011-AUG1204 rev. A.0