155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Features • Duplex ST Single Mode Transceiver • Industry Standard 1x9 Footprint • Intermediate Reach SONET OC-3 SDH STM-1 Compliant • Single +3.3V Power Supply • PECL/LVPECL Differential Inputs and Outputs • Wave Solderable and Aqueous Washable • LED Multisourced 1x9 Transceiver Interchangeable • Class 1 Laser Int. Safety Standard IEC 825 Compliant • Uncooled Laser Diode with MQW Structure • Complies with Telcordia (Bellcore) GR-468-CORE • Temperature Range: -40 to 85ºC • SD PECL/LVPECL level • ATM 155 Mbps Links Application • SONET/SDH Equipment Interconnect Application • Receiver squelch function • RoHS compliance available Absolute Maximum Rating Parameter Symbol Min. Max. Unit Power Supply Voltage Vcc 0 3.6 V Output Current Iout 0 30 mA Soldering Temperature Note - - 260 ºC Tstg -40 85 ºC Symbol Min. Typ. Max. Unit Vcc 3.1 3.3 3.5 V Topr -40 - 85 ºC - 155 - Mbps Notes Storage Temperature 10 seconds on leads only Recommended Operating Condition Parameter Power Supply Voltage1 Operating Temperature1 (Case) Data Rate Note 1 : Please refer to ordering information Transmitter Specifications, Parameter Symbol Min Typical Max Unit Po -15 - -8 dBm Optical Optical Transmit Power λ 1261 1310 1360 nm Output Spectrum Width ∆λ - - 7.7 nm Extinction Ratio ER 8.2 - - dB Output Center Wavelength output power is coupled into a 9/125 µm single mode fiber RMS(σ) Output Pulse Mask Compliant with FDDI SMF-PMD1 Output Eye Compliant with Bellcore TR-NWT-000253 and ITU-T recommendation G.957 Optical Rise Time tr - - 2 ns 10% to 90% Values Optical Fall Time tf - - 2 ns 10% to 90% Values Relative Intensity Noise RIN - - -116 dB/Hz Total Jitter TJt - - 1.2 ns www.municom.de 1 Measured with 223-1 PRBS with 72 ones and 72 zeros. LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Transmitter Specifications, Parameter Symbol Min Typical Max Unit Power Supply Current ICC - - 160 mA Data Input Current-Low IIL -350 - - µA Data Input Current-High IIH - - 350 µA Differential Input Voltage VIH-VIL 300 - - mV Data Input Voltage-Low VIL-VCC -2.0 - -1.58 V Data Input Voltage-High VIH-VCC -1.1 - -0.74 V Notes Electrical Maximum current is specified at Vcc= Maximum @ maximum temperature These inputs are compatible with 10K, 10KH and 100K ECL and PECL inputs Receiver Specifications, Parameter Symbol Min Typical Max Unit Notes - - - -34 dBm Maximum Input Power Pin -7 - - dBm Signal Detect-Asserted Pa - - -34 dBm Measured on transition: low to high Signal Detect-Deasserted Pd -47 - - dBm Measured on transition: high to low 1.0 - 4.0 dB 1100 - 1600 nm Symbol Min Typical Max Unit ICC - - 100 mA Data Output Voltage-Low VOL -Vcc -2 - -1.58 V Data Output Voltage-High VOH- Vcc -1.1 - -0.74 V Signal Detect Output Voltage-Low VSDL-Vcc -2 - -1.58 V Signal Detect Output Voltage-High VSDH- Vcc -1.1 - -0.74 V Optical Sensitivity Signal Detect-Hysteresis Wavelength of Operation measured with 223-1 PRBS with 72 ones and 72 zeros. Receiver Specifications, Parameter Notes Electrical Power Supply Current www.municom.de 2 The current excludes the output load current These outputs are compatible with 10K, 10KH and 100KECL and PECL outputs. C-13-155-T3-SST3A-14-G5 LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Connection Diagram 1. (Rx GND) 2. (RD +) 3. (RD-) 4. (SD) 5. (Rx Vcc) 6. (Tx Vcc) 7. (TD-) 8. (TD+) 9. (Tx GND) NC Top View NC Receiver Signal Ground Receiver Data Out Receiver Data Out Bar Signal Detect Receiver Power Supply Transmitter Power Supply Transmitter Data In Bar Transmitter Data in Transmitter Signal Ground PIN Symbol 1 RxGND 2 RD+ See recommended circuit schematic 3 RD- See recommended circuit schematic 4 SD Active high on this indicates a received optical signal 5 RxVcc DC power for the receiver section 6 TxVcc DC power for the transmitter section 7 TD- See recommended circuit schematic TD+ See recommended circuit schematic 8 Warnings 9 TxGND Notes Directly connect this pin to the receiver ground plane Directly connect this pin to the transmitter ground plane Legal Notice www.municom.de 3 LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Recommended Circuit Schematic C-13-155-T3-SST3A-14-G5 Tx Vcc C5 Rx Vcc 9 8 R1 7 6 5 4 3 2 1 R3 R9 R5 C6 R7 TD + RD + TD - RD - Tx Vcc SD Rx Vcc R2 R4 No internal connection No internal connection Transceiver Top view R10 R6 R8 L1 Vcc Notes +3.3V: R1=R3=R5=R7=R9=130 R2=R4=R6=R8=R10=82 C1=C2=C3=C5=C6=0.1F C4=10F L1=L2=1H C3 C1 L2 C4 C2 Rx Vcc Tx Vcc The split-loaded terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc. A GND plane under the module is required for good EMI and sensitivity performance. Label Model Number: C-13-155-T3-SST3A-14-G5 www.municom.de 4 LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Package Diagram y C-13-155-T3-SST3A-14-G5 Top View Front View Side View Rear View www.municom.de 5 Units: mm LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Ordering Information Available Options: C-13-155-T3-SST3A-14-G5 Part numbering Definition: C - 13 - 155 - T3 - S ST Tx Power Temperature and Package -14 -RoHS • Wavelength 13 = 1310 nm • Communication protocol (155Mbps) 155 = PECL Signal Detection Optupt • T3 = +3.3V Transceiver, FP • Single mode fiber • Connector options (ST) • TxPower 3 = -15 to -8 dBm • Temperature and Package A = Commercial temperature (-40 to 85℃ ) • -14 :Municom customization label, squelch function, ST housing is isolated from the PCB ground • RoHS compliance available G5 = RoHS 5/6-compliant product (lead exemption) www.municom.de 6 LUMNDS1914-Aug1208 Rev. A.1 155 Mbps Single Mode Transceiver C-13-155-T3-SST3A-14-G5 Qualification Information The 155 Mbps SM Transceiver has passed the following qualification tests and meets the intent of Telcordia (Bellcore) GR-468-CORE. Qualification Test Condition Sample Size Reference Mechanical Shock 500 g 11 MIL-STD-883 20g, 20 Hz-2,000 Hz 11 MIL-STD-883D Method 2007 Vibration Solderability Thermal Shock Temperature Cycling Damp Heat Cyclic Moisture Resistance ESD - 11 MIL-STD-883E Method 2003.7 25ºC 11 MIL-STD-883 Method 1011 MIL-STD-883 Method 1010 500 cycles 11 40ºC, 95% RH, 1344 hrs 11 MIL-STD-202 Method 103 10 cycles 11 MIL-STD-883 Method 1004 ± 500V 6 MIL-STD-883D Method 3015.7 Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at Municom’s sole and absolute discretion. Municom warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and Municom expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. Municom assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and Municom makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Municom customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify Municom for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that Municom is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact Municom to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. All rights reserved www.municom.de 7 LUMNDS1914-Aug1208 Rev. A.1