Nov 13, 2006 100BASE-FX Spring-Latch SGMII SFP Transceiver (For 2km transmission with MCU version) Members of FlexonTM Family Compatible with FDA 21 CFR 1040.10 and 1040.11, Class I Compatible with Telcordia GR-468-CORE RoHS compliance Description Fiberxon FTM-3401C-SL2CG is designed for 100BASE-FX applications, supporting distance from 0.5m to 2km on MMF with build-in PHY device Features Build-in PHY supporting SGMII Interface Build-in high performance MCU supporting easier configuration Support more link status monitor, such as CRC, package counter and Far End Fault Indication (FEFI) 100BASE-FX operation 1310nm FP laser and PIN photo-detector 0.5m~2km transmission with MMF Standard serial ID information Compatible with SFP MSA SFP MSA package with duplex LC connector With Spring-Latch for high density application Very low EMI and excellent ESD protection +3.3V single power supply Operating case temperature: 0 to +70°C Applications Switch to Switch interface Switched backplane applications Router/Server interface supporting SGMII interface. The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver. The standard serial ID information Compatible with SFP MSA describes the transceiver’s capabilities, standard interfaces, manufacturer and information. The host equipment can access this information via the 2-wire serial CMOS EEPROM protocol. For further information, please refer to SFP Multi-Source Agreement (MSA). Fiberxon SGMII SFP transceiver product family supports a range of media (Cat 5 copper, multi-mode fiber, single mode fiber), multi-rate (10/100/1000 Mbps) capabilities. Building-in high performance MCU in this module, Host can more easily configure all functions of FTM-3401C-SL2CG. Other optical transmission systems Standard Compatible with SFP MSA Compatible with IEEE 802.3-2002 Compatible with FCC 47 CFR Part 15, Class B other Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 1 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 Regulatory Compliance The transceivers have been tested according to American and European product safety and electromagnetic compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer to FlexonTM regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at the end of the documentation. Table 1 - Regulatory Compliance Feature Standard Electrostatic Discharge MIL-STD-883E (ESD) to the Electrical Pins Method 3015.7 Electrostatic Discharge (ESD) IEC 61000-4-2 to the Duplex LC Receptacle GR-1089-CORE Electromagnetic Interference (EMI) Immunity Performance Class 1(>500 V) Compatible with standards FCC Part 15 Class B EN55022 Class B (CISPR 22B) Compatible with standards VCCI Class B IEC 61000-4-3 Laser Eye Safety Component Recognition Compatible with standards FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 product. TUV Certificate No. 50030043 UL and CSA UL file E223705 2002/95/EC 4.1&4.2 RoHS Compatible with Class I laser Compliant with standards note 2005/747/EC Note: In light of item 5 in Annex of 2002/95/EC, “Pb in the glass of cathode ray tubes, electronic components and fluorescent tubes.” and item 13 in Annex of 2005/747/EC , “ Lead and cadmium in optical and filter glass.” ,the two exemptions are being concerned for Fiberxon’s transceivers, because Fiberxon’s transceivers use glass, which may contain Pb, for components such as lenses, windows, isolators, and other electronic components. Absolute Maximum Ratings Stress in excess of the maximum absolute ratings can cause permanent damage to the module. Table 2 - Absolute Maximum Ratings Parameter Symbol Min. Max. Unit Storage Temperature TS -40 +85 °C Supply Voltage VCC -0.5 3.6 V - 5 95 % Operating Relative Humidity Recommended Operating Conditions Table 3- Recommended Operating Conditions Parameter Symbol Min. Operating Case Temperature TC 0 Power Supply Voltage VCC 3.10 Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Typical 3.30 Max. Unit +70 °C 3.50 V Notes Page 2 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Power Supply Current ICC Nov. 13, 2006 320 Date Rate 125 mA 1 Mbps Note 1: The max. power supply current after module work stable. Optical and Electrical Characteristics Table 4 - Optical and Electrical Characteristics Parameter Symbol Min. Typical Max. Unit Notes 1310 1355 nm -14 dBm 2 2 Transmitter Centre Wavelength λC 1270 Average Output Power P0ut -20 P0ut@TX Disable Asserted P0ut -45 dBm σ 7.7 nm Spectral Width (RMS) Extinction Ratio EX Rise/Fall Time (20%～80%) tr/tf Output Optical Eye Data Input Swing Differential Input Differential Impedance TX Fault dB 3 ns Compatible with IEEE 802.3-2002 (SGMII Series interface) TX Disable 9 VIN 200 ZIN 80 100 3 4 2100 mV 120 Ω Disable 2.0 Vcc Enable Vee Vee+0.8 Fault 2.0 Vcc Normal Vee Vee+0.5 5 V V Receiver Centre Wavelength λC 1260 Receiver Sensitivity 1310 1570 nm -31.5 dBm 6 6 Receiver Overload -8 dBm Return Loss 12 dB LOS De-Assert -32.5 LOS Assert -45 LOS Hysteresis 0.5 dBm 4.5 dB 0.43 UI 370 2000 mV High 2.0 Vcc+0.3 Low Vee Vee+0.5 Total Jitter (SGMII Series Interface) Data Output Swing Differential (SGMII Series Interface) LOS dBm TJ VOUT V Notes: 2. The optical power is launched into MMF 62.5/125um. 3. Unfiltered, measured with 4B/5B code for 125Mbps. 4. Measured with 4B/5B code for 125Mbps. 5. PECL logic, internally AC coupled. 6. Measured with 4B/5B code for 125Mbps, worst-case extinction ratio, BER ≤1×10-10. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 3 of 10 5 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 EEPROM Information The SFP MSA defines a 256-byte memory map in EEPROM describing the transceiver’s capabilities, standard interfaces, manufacturer, and other information, which is accessible over a 2-wire serial interface at the 8-bit address 1010000X (A0h). For the memory contents, please refer to Table 5. Table 5 - EEPROM Serial ID Memory Contents (A0h) Field Size Addr. (Bytes) Name of Field Hex Description 0 1 Identifier 03 SFP 1 1 Ext. Identifier 04 MOD4 2 1 Connector 07 LC 3—10 8 Transceiver 00 00 00 20 00 00 00 00 11 1 Encoding 02 4B5B 12 1 BR, nominal 01 100Mbps 13 1 Reserved 00 14 1 Length (9um)-km 00 15 1 Length (9um) 00 16 1 Length (50um) C8 2km 17 1 Length (62.5um) C8 2km 18 1 Length (copper) 00 19 1 Reserved 20—35 16 Vendor name 36 1 Reserved 37—39 3 Vendor OUI 40—55 16 Vendor PN 56—59 4 Vendor rev xx xx xx xx 60—61 2 Wavelength 05 1E 62 1 Reserved 00 63 1 CC BASE xx 64—65 2 Options 00 1A 66 1 BR, max 00 67 1 BR, min 00 68—83 16 Vendor SN 84—91 8 92—94 3 Reserved 00 00 00 95 1 CC_EXT xx 96—154 58 Vendor specific 155 1 Reserved 156-247 Transmitter Code 00 46 49 42 45 52 58 4F 4E 20 49 4E 43 2E 20 20 20 “FIBERXON INC. “(ASCⅡ) 00 00 00 00 46 54 4D 2D 33 34 30 31 43 2D 53 4C 32 43 47 20 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx Vendor date codexx xx xx xx xx xx 20 20 “FTM-3401C-SL2CG” (ASCⅡ) ASCⅡ( “31 30 20 20” means 1.0 revision) 1310nm Check sum of bytes 0 - 62 LOS, TX_FAULT and TX_DISABLE ASCⅡ Year(2 bytes), Month(2 bytes), Day (2 bytes) Check sum of bytes 64 - 94 Read only Vendor specific 248 1 Status Read only 249 1 CFG0 Work mode configuration Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 4 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 250 1 CFG1 Work mode configuration 251 1 CFG2 Work mode configuration 252 1 Status Module status indication 253 1 Reserved Read only 254 1 PSWH Password entry 255 1 PSWL Password entry Note: The “xx” byte should be filled in according to practical case. For more information, please refer to the related document of SFP Multi-Source Agreement (MSA) and application note of FTM-3401C-SL2CG. Easier Configuration Designing-in a high performance MCU in FTM-3401C-SL2CG, host can configure Fiberxon’s SGMII series product easily. For FTM-3401C-SL2CG, host only need access few registers of A0H via I2C to configure SGMII series module, such as speed-selection, Auto-negotiation, LOS/Link detection, TX disable, FEFI/RFI and CRC counter function support. Host can get inner status via access specific register of FTM-3401C-SL2CG. The operation data rate can be configured via hardware pin and I2C bus independently. For more detailed information, please refer to application note of FTM-3401C-SL2CG. Recommended Host Board Power Supply Circuit Figure 1 shows the recommended host board power supply circuit. Figure 1, Recommended Host Board Power Supply Circuit Recommended Interface Circuit Figure 2 shows the recommended interface circuit. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 5 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 SGMII Interface Host Board SFP Module VccT 10 KΩ TX Disable TX Fault Z=50Ω 100Ω SGMII/802.3z SerDes MAC Controller 100Ω TD + Laser driver 100Ω Z=50Ω TD - Z=50Ω RD + Z=50Ω RD - Controller PHY IC 100Ω Amplifier Vcc(+3.3V) 6×4.7 K to10KΩ Rate selection LOS MOD-DEF2 MOD-DEF1 MOD-DEF0 MCU Figure 2, Recommended Interface Circuit Pin Definitions Figure 3 below shows the pin numbering of SFP electrical interface. The pin functions are described in Table 6 with some accompanying notes. P in 2 0 T O P V IE W OF BOARD P in 1 1 P in 1 0 B O T T O M V IE W OF BOARD P in 1 Figure 3, Pin View Table 6– Pin Function Definitions Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 6 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Pin No. Name 1 VeeT 2 TX Fault 3 Preliminary Datasheet Function Nov. 13, 2006 Plug Seq. Notes Transmitter Ground 1 Transmitter Fault Indication 3 Note 1 TX Disable Transmitter Disable 3 Note 2 4 MOD-DEF2 Module Definition 2 3 Note 3 5 MOD-DEF1 Module Definition 1 3 Note 3 6 MOD-DEF0 Module Definition 0 3 Note 3 7 Rate Select Not Connected 3 8 LOS Loss of Signal 3 9 VeeR Receiver Ground 1 10 VeeR Receiver Ground 1 11 VeeR Receiver Ground 1 12 RD- Inv. Received Data Out 3 Note 5 13 RD+ Received Data Out 3 Note 5 14 VeeR Receiver Ground 1 15 VccR Receiver Power 2 16 VccT Transmitter Power 2 17 VeeT Transmitter Ground 1 18 TD+ Transmit Data In 3 Note 6 19 TD- Inv. Transmit Data In 3 Note 6 20 VeeT Transmitter Ground 1 Note 4 Notes: 1. TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V. 2. TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are: Low (0~0.8V): Transmitter on (>0.8V, <2.0V): Undefined High (2.0~3.465V): Transmitter Disabled Open: Transmitter Disabled 3. MOD-DEF 0,1,2 are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board. The pull-up voltage shall be VccT or VccR. MOD-DEF 0 is grounded by the module to indicate that the module is present MOD-DEF 1 is the clock line of two wire serial interface for serial ID MOD-DEF 2 is the data line of two wire serial interface for serial ID 4. LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. In the low state, the output will be pulled to less than 0.8V. 5. These are the differential receiver output. They are internally AC-coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SGMII. 6. These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 7 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 Mechanical Design Diagram The mechanical design diagram is shown in Figure 4. Figure 4, Mechanical Design Diagram of the SFP with Spring- Latch Ordering information FTM 3 4 0 1 Medium C SL C G Others G: RoHS compliance Receptacle C: LC 3 : 1310nm Function 4: PHY MCU C: MCU version Distance 2: 2KM Data rate 01: 125 Mbps Product part Number 2 Package SL: SFP with Spring-latch Media Data Rate(Mbps) Transmission Note Distance(km) FTM-3401C-SL2CG Multi-Mode Fiber 125 Fiberxon Proprietary and Confidential, Do Not Copy or Distribute 2 MCU version Page 8 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 Related SGMII SFP Products Product part Transmission Media Data Rate(Mbps) FTM-C012R-LCG Cat. 5 Copper 10/100/1000 100m FTM-8401C-SL2G Multi-Mode Fiber 125 2km FTM-3401C-SL2G Multi-Mode Fiber 125 2km FTM-3401C-SL10G Single mode fiber 125 10km Single mode fiber 125 10km FTM-3413C-SLG Single mode fiber 125/1250 10km FTM-3413C-SL05G Multi-Mode Fiber 125/1250 550m FTM-3401C-SL2CG Multi-Mode Fiber 125 2km MCU version FTM-3401C-SL10CG Single mode fiber 125 10km MCU version FTM-8401C-SL2CG Single mode fiber 125 2 MCU version FTM-3413C-SLCG Single mode fiber 125/1250 10km MCU version FTM-3413C-SL05CG Multi-Mode Fiber 125/1250M 550m MCU version Number FTM-3401S-SL10BG/ FTM-5401S-SL10BG Distance Note Related Documents For further information, please refer to the following documents: ■ Fiberxon Spring-Latch SFP Installation Guide ■ Fiberxon SFP Application Notes ■ SFP Multi-Source Agreement (MSA) Obtaining Document You can visit our website: http://www.fiberxon.com Or contact with Fiberxon, Inc. America Sales Office listed at the end of documentation to get the latest documents. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 9 of 10 125M SGMII Spring-Latch SFP Transceiver 2km MMF transmission Preliminary Datasheet Nov. 13, 2006 Revision History Revision Rev 1a Initiate Review Approve Henry.Xiao Tripper.Huang Walker.Wei Subject Initial datasheet Release Date Nov. 13, 2006 © Copyright Fiberxon Inc. 2006 All Rights Reserved. All information contained in this document is subject to change without notice. The products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Fiberxon product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Fiberxon or third parties. All information contained in this document was obtained in specific environments, and is presented as an illustration. The results obtained in other operating environment may vary. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN ”AS IS” BASIS. In no event will Fiberxon be liable for damages arising directly from any use of the information contained in this document. Contact U.S.A. Headquarter: 5201 Great America Parkway, Suite 340 Santa Clara, CA 95054 U. S. A. Tel: 408-562-6288 Fax: 408-562-6289 Or visit our website: http://www.fiberxon.com Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 10 of 10