Mar. 16, 2007
2x5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)
FTM-9412S-F20FD(G)
(IEEE 802.3ah™-2004 1000BASE-PX20-U)
Members of FlexonTM Family
Standard
Compliant with SFF MSA
Compliant with IEEE Std 802.3ah™ -2004
1000BASE-PX20-U
Compliant with FCC 47 CFR Part 15, Class B
Compliant with FDA 21 CFR 1040.10 and 1040.11,
Class I
Features
Description
Single fiber bi-directional data links with symmetric
FTM-9412S-F20F(G)/F20FD(G) is Optical Network Unit
1.25Gbps upstream and 1.25Gbps downstream
(ONU) for IEEE802.3ah™-2004 1000BASE-PX20-U
Integrated with micro-optics WDM filter for dual
application.
wavelength Tx/Rx operation at 1310/1490nm
The transceiver is the high performance module for
1310nm burst-mode transmitter with FP laser
1490nm continuous-mode receiver with PIN-TIA
1550nm optical signal rejection
0 to 70℃ operating case temperature
2× 5 SFF package with SC receptacle form
The transmitter section uses a multiple quantum well
Single 3.3V power supply
1310nm FP laser and is ClassⅠlaser compliant product
LVPECL compatible data input/output interface
according to international safety standard IEC-60825.
LVTTL transmitter burst-mode control
LVTTL receiver signal-detected indication
Low EMI and excellent ESD protection
Class I laser safety standard IEC-60825 compliant
1.25Gbps data link in single fiber by using 1310nm
burst-mode transmitter and 1490nm continuous-mode
receiver with 1550nm optical signal rejection.
The receiver section uses an integrated 1490nm PIN
and preamplifier mounted in an optical header and
limiting post-amplifier IC.
The optical burst output can be enabled by a LVTTL
logic high-level input of TX_BRST. Signal Detected (SD)
Applications
output is provided to indicate the detection of an input
optical signal of receiver.
Gigabit Ethernet Passive Optical Networks
(GEPON) – ONU side
Gigabit Ethernet Point-to-Point Bi-directional
Transmission
Media Converts for Fiber-In-The-Loop (FITL)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 1 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Regulatory Compliance
The transceivers have been tested according to American and European product safety and electromagnetic
compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer to
FlexonTM regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at
the end of documentation.
Table 1 - Regulatory Compliance
Feature
Standard
Electrostatic Discharge
MIL-STD-883E
(ESD) to the Electrical Pins
Method 3015.7
Performance
Class Ⅰ(>500 V)
FCC Part 15 Class B
Electromagnetic
EN55022 Class B (CISPR 22B)
Interference (EMI)
Compliant with standards
VCCI Class B
Immunity
IEC 61000-4-3
Compliant with standards
FDA 21CFR 1040.10 and 1040.11
Laser Eye Safety
Compliant with Class I laser product
EN60950, EN (IEC) 60825-1,2
Component Recognition
UL and CSA
Compliant with standards
Absolute Maximum Ratings
Absolute Maximum Ratings are those values, beyond which, some damages may occur to the devices. Exposure
to conditions above the Absolute Maximum Ratings listed in Table 2 may negatively impact the reliability of the
products.
Table 2 - Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Unit
Storage Ambient Temperature
TSTG
-40
85
°C
Operating Case Temperature
TC
0
70
°C
Operating Humidity
HOPR
5
95
%
Power Supply Voltage
VCC
0
4
V
GND
Vcc
V
Input Voltage
Receiver Damaged Threshold
+7
Soldering Temperature
Note
dBm
260/10
°C/s
1
400
°C
2
Note 1: Soldering on lead only, for FTM-9412S-F20FG and FTM-9412S-F20FDG
Note 2: Only for soldering by iron and 10 seconds on leads only, for FTM-9412S-F20F and FTM-9412S-F20FD
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 2 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Recommended Operating Conditions
Table 3 - Recommended Operating Conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Note
Power Supply Voltage
VCC
3.13
3.3
3.47
V
3.3V±5%
Operating Case Temperature
TC
0
70
°C
HOPR
5
95
%
Operating Humidity Range
Data Rate
1.25
Data Rate Drift
-100
Gbit/s
+100
PPM
Optical and Electrical Characteristics
Table 4 - Transmitter Optical and Electrical Characteristics (0°C <TC<70°C and 3.13V<VCC<3.47V)
Parameter
Symbol
Min.
Optical Center Wavelength
λC
1276
Optical Spectrum Width (RMS)
∆λ
Average Launch Power
POUT
Average Launch Power-OFF Transmitter
POFF
Typ.
Max.
Unit
1356
nm
2.8
nm
+4
dBm
-45
dBm
0
Extinction Ratio
ER
Total Jitter
TJ
0.35
UI
TR/TF
260
ps
Burst Turn On Time
TBURST_ON
30
ns
Burst Turn Off Time
TBURST_OFF
Rise/Fall Time (20%-80%)
9
dB
30
ns
Burst Enable Duration
TEN_DUR
600
ns
Burst Disable Duration
TDIS_DUR
100
ns
RIN15OMA
-115
dB/Hz
Optical Return Loss Tolerance
15
dB
Transmitter Reflectance
-10
dB
Optical Eye Diagram
Compliant With IEEE Std 802.3ah™-2004
Data Input Differential Swing
VIN
200
Common-Mode Input Voltage
VCM
VCC-1.49
Input Differential Impedance
ZIN
90
Note
1
2
2.3
4
2,5
1600
mV
6
VCC-1.32
VCC- VIN/4
V
7
100
110
Ω
Power Supply Current
ICC_TX
200
mA
Transmitter Burst Control Voltage - Low
VTDIS, L
0
0.8
V
Transmitter Burst Control Voltage -High
VTDIS, H
2.0
VCC
V
8
Note 1: Launched into 9/125um Single Mode Fiber.
Note 2: Measured with PRBS 27-1 test pattern @1.25 Gbit/s.
Note 3: Measured with the Bessel-Thompson filter OFF.
Note 4: Refer to Timing Parameter Definition in Burst Mode Sequence.
Note 5: Transmitter eye mask definition is {0.22UI, 0.375UI, 0.20UI, 0.20UI, 0.30UI}.
Note 6: Compatible with LVPECL/CML input, AC coupled internally. (See Recommended Interface Circuit)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 3 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Note 7: Only for FTM-9412S-F20FD(G)
Note 8: TX_BRST (See Pin Function Definitions)
Table 5 - Receiver Optical and Electrical Characteristics (0°C <TC<70°C and 3.13V<VCC<3.47V)
Parameter
Symbol
Min.
Operating Wavelength
1480
Sensitivity
PSEN
Saturation
PSAT
Signal-Detected Assert Level
PSDA
Signal-Detected Deassert Level
PSDD
-39
PSDA- PSDD
0.5
Signal-Detected Hysteresis
Max.
Unit
1500
nm
-26.5
dBm
-3
dBm
-27
Receiver Reflectance
WDM Filter Isolation
Typical
1
dBm
2
dBm
3
6
dBm
-12
dB
ISO(1550)
38
dB
1550nm
ISO(1650)
35
dB
1650nm
Power Supply Current
ICC_RX
120
mA
Data Output Differential Swing
VOUT
400
1600
mV
Signal-Detected Voltage - Low
VSD, L
0
0.8
V
Signal-Detected Voltage - High
VSD, H
2.0
VCC
V
Signal-Detected Assert Time
TASS
100
µs
TDAS
100
Signal-Detected Deassert Time
Notes
7
4
5
µs
-12
Note 1: Measured with a PRBS 2 -1 test pattern @1.25Gbit/s and ER=9dB, BER =10 .
Note 2: An increase in optical power above the specified level will cause the Signal Detect output to switch from a
low state to a high state.
Note 3: A decrease in optical power below the specified level will cause the Signal Detect output to switch from a
high state to a low state.
Note 4: LVPECL output, AC coupled internally, guaranteed in the full range of input optical power (-3dBm to
-27dBm) (See Recommended Interface Circuit)
Note 5: SD (See Pin Function Definitions)
Table 6 - Electrical Input/Output Coupling Mode
Input (TD+/TD-)
Output (RD+/RD-)
FTM-9412S-F20F(G)
P/N
Internal AC Coupling
Internal AC Coupling
FTM-9412S-F20FD(G)
Internal DC Coupling
Internal AC Coupling
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 4 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
TX_BRST
Mar. 16, 2007
T DIS_DUR
T EN _DU R
TD+
TD-
Average Power
<=-45dBm
Optical
Power
Output
ER for CM
operation
T BUR ST_ON
ER and Average
Power within 15%
CM operation
T BUR ST_OFF
Burst Off Condition
Burst On Condition
Figure 1 Timing Parameter Definition in Burst Mode Sequence
Recommended Interface Circuit
Figure 2 shows the recommended interface schemes for FTM-9412S-F20F(G)
Figure 2 Recommended Interface Circuit (FTM-9412S-F20F(G))
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 5 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Note A: Open emitter output internally.
Note B: LVPECL output, AC coupled internally.
Input stage in SerDes IC is assumed with high impedance and internal bias to Vcc-1.3V
R1=R2=R3=R4=N.C, R5=100Ω
Input stage in SerDes IC is assumed without internal bias to Vcc-1.3V
R1=R2=82Ω,R3=R4=130Ω,R5=N.C
Figure 3 shows the recommended interface schemes for FTM-9412S-F20FD(G)
Figure 3 Recommended Interface Circuit (FTM-9412S-F20FD(G))
Note A: Open emitter output internally.
Note B: LVPECL output, AC coupled internally.
Input stage in SerDes IC is assumed with high impedance and internal bias to Vcc-1.3V
R1=R2=R3=R4=N.C, R5=100Ω
Input stage in SerDes IC is assumed without internal bias to Vcc-1.3V
R1=R2=82Ω,R3=R4=130Ω,R5=N.C
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 6 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Pin Definitions
2×5 SFF planform in Figure 4 below shows the pin information of electrical interface and mounting studs.
Functions are described in Table 7 with some accompanying notes.
Figure 4 2×5 SFF Planform
Table 7 - Pin Function Definitions
Pin No.
Name
Description
Notes
1
VEER
Receiver Signal Ground
2
VCCR
Receiver Power Supply
3
SD
Receiver Signal-Detected Indication
4
RD-
Inverted Receiver Data Output
5
RD+
Non-inverted Receiver Data Output
6
VCCT
Transmitter Power Supply
7
VEET
Transmitter Signal Ground
8
TX_BRST
Transmitter Burst Control
9
TD+
Transmitter Non-inverted Data Input
10
TD-
Transmitter Inverted Data Input
MS
MS
Mounting Studs
5
HL
HL
Housing Leads
6
1
2
3
4
Note 1: TTL logic output, with internal 10KΩ pull-up resistor.
Optical Signal-Detected: High; Optical Signal Loss: Low
Note 2: LVPECL logic output, AC coupled internally. (See Recommended Interface Circuit)
Note 3: A positive level enable optical signal output under burst mode.
(See Timing Parameter Definition in Burst Mode Sequence)
Note 4: Note 4: Compatible with LVPEC input
(See Recommended Interface Circuit and Table 6 - Electrical Input/Output Coupling Mode)
Note 5: The mounting studs are provided for transceiver mechanical attachment to circuit board. They may also
provide an optional connection of the transceiver to the equipment chassis ground. The holes in the circuit
board must be tied to chassis ground.
Note 6: The housing leads may be provided for additional signal grounding. These additional grounds may improve
signal integrity, EMC, or ESD performance. The holes in the circuit board must be included and be tied to
signal ground.
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 7 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Mechanical Design Diagram
The form factor is 2×5 SFF.
The mechanical design diagram is shown in Figure 5. (Dimension in mm)
Figure 5 Mechanical Design Diagram
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 8 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Ordering Information
Part No.
FTM-9412S-F20F
FTM-9412S-F20FD
FTM-9412S-F20FG
FTM-9412S-F20FDG
Product Description
1310nm(TX)/1490nm(RX), SC/UPC receptacle 2×5 SFF for GEPON ONU 20km (PX20)
application, 0°C ~ 70°C(case temperature), Tx AC Coupling, Rx AC Coupling
1310nm(TX)/1490nm(RX), SC/UPC receptacle 2×5 SFF for GEPON ONU 20km (PX20)
application, 0°C ~ 70°C(case temperature), Tx DC Coupling, Rx AC Coupling
1310nm(TX)/1490nm(RX), SC/UPC receptacle 2×5 SFF for GEPON ONU 20km (PX20)
application, 0°C~70°C(case temperature), Tx AC Coupling, Rx AC Coupling, RoHS compliance
1310nm(TX)/1490nm(RX), SC/UPC receptacle 2×5 SFF for GEPON ONU 20km (PX20)
application, 0°C~70°C(case temperature), Tx DC Coupling, Rx AC Coupling, RoHS compliance
Related Documents
For further information, please refer to the following documents:
IEEE Std 802.3ahTM-2004
Obtaining Document
You can visit our website:
http://www.fiberxon.com/
Or contact with Fiberxon, Inc. America Sales Office listed at the end of documentation to get the latest documents.
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 9 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
Revision History
Reversion
Initiate
Review
Approve
Subject
Release
Date
Pre 1a
Johnny Yang
Peter Tang
Peter Tang
Initial datasheet (Doc No. DS3493013-1a)
2006-04-06
Revised datasheet
Pre 1b
Jacob Cai
Johnny Yang
Peter Tang
Change the product picture
2006-06-30
(Doc No. DS3493013-1b)
Revised datasheet
Pre 1c
Jacob Cai
Johnny Yang
Peter Tang
Change the Mechanical Design Diagram in
Figure 5
2006-08-09
(Doc No. DS3493013-1c)
Revised datasheet
Pre 1d
Jacob Cai
Johnny Yang
Peter Tang
1. Change Mechanical Design Diagram in
Figure 5;
2006-11-10
(Doc No. DS3493013-1d)
Revised datasheet
1. Change the photo in cover page;
Pre 1e
Jacob Cai
Johnny Yang
Peter Tang
2. Change Figure 4;
2007-1-19
3. Update Table 7 and its notes.
(Doc No. DS3493013-1e)
Revised datasheet
1. Update
“Product
Description”
in
“Ordering Information” section.
Pre 1f
Jacob Cai
Johnny Yang
Peter Tang
2007-3-16
2. Update Figure 5;
3. Update “Average Launch Power” item in
Table 4;
(Doc No. DS3493013-1f)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 10 of 11
Doc No: DS3493013-1f
2×5 SFF GEPON ONU Diplexer
FTM-9412S-F20F(G)/ FTM-9412S-F20FD(G)
IEEE 802.3ahTM 1000BASE-PX20U
Preliminary Data Sheet
Mar. 16, 2007
© Copyright Fiberxon Inc. 2007
All Rights Reserved.
All information contained in this document is subject to change without notice. The products described in this
document are NOT intended for use in implantation or other life support applications where malfunction may result
in injury or death to persons.
The information contained in this document does not affect or change Fiberxon’s product specifications or
warranties. Nothing in this document shall operate as an express or implied license or indemnity under the
intellectual property rights of Fiberxon or third parties. All information contained in this document was obtained in
specific environments, and is presented as an illustration. The results obtained in other operating environment may
vary.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN ”AS IS” BASIS. In no event will
Fiberxon be liable for damages arising directly from any use of the information contained in this document.
Contact
U.S.A. Headquarter:
5201 Great America Parkway, Suite 340
Santa Clara, CA 95054
U. S. A.
Tel: 408-562-6288
Fax: 408-562-6289
Or visit our website: http://www.fiberxon.com/
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute
Page 11 of 11
Doc No: DS3493013-1f