STMICROELECTRONICS M48T37V

M48T37Y
M48T37V
5.0 or 3.3 V, 256 Kbit (32 Kbit x 8) TIMEKEEPER® SRAM
Features
■
Integrated ultra low power SRAM, real-time
clock, power-fail control circuit, and battery
■
Frequency test output for real-time clock
software calibration
■
Automatic power-fail chip deselect and WRITE
protection
■
Watchdog timer
■
WRITE protect voltage
(VPFD = Power-fail deselect voltage):
– M48T37Y: VCC = 4.5 to 5.5 V
4.2 V ≤ VPFD ≤ 4.5 V
– M48T37V: VCC = 3.0 to 3.6 V
2.7 V ≤ VPFD ≤ 3.0 V
44
1
■
Packaging includes a 44-lead SOIC and
SNAPHAT® top (to be ordered separately)
■
SOIC package provides direct connection for a
SNAPHAT® top which contains the battery and
crystal
■
Microprocessor power-on reset (valid even
during battery backup mode)
■
Programmable alarm output active in the
battery backup mode
■
Battery low flag
■
RoHS compliant
– Lead-free second level interconnect
August 2010
SNAPHAT® (SH)
Battery/crystal
Doc ID 7019 Rev 9
SOH44 (MH)
44-pin SOIC
1/30
www.st.com
1
Contents
M48T37Y, M48T37V
Contents
1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Operation modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
2.1
READ mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2
WRITE mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
Data retention mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1
Reading the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3
Stopping and starting the oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4
Setting the alarm clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5
Calibrating the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.6
Watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.7
Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.8
Programmable interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.9
Battery low flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.10
Initial power-on defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.11
VCC noise and negative going transients . . . . . . . . . . . . . . . . . . . . . . . . . 18
4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8
Environmental information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
READ mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WRITE mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Alarm repeat modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Power down/up AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Power down/up trip points DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT®, package mechanical data . 24
SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, package mechanical data . 25
SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, package mechanical data 26
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SNAPHAT® battery table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Doc ID 7019 Rev 9
3/30
List of figures
M48T37Y, M48T37V
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
4/30
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SOIC connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
READ mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
WRITE enable controlled, WRITE AC waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chip enable controlled, WRITE AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Alarm interrupt reset waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Backup mode alarm waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Supply voltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Crystal accuracy across temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Clock calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Power down/up mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT® outline. . . . . . . . . . . . . . . . . 24
SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, pack. outline . . . . . . . . . . . 25
SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, pack. outline . . . . . . . . . . 26
Recycling symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Doc ID 7019 Rev 9
M48T37Y, M48T37V
1
Description
Description
The M48T37Y/V TIMEKEEPER® RAM is a 32 Kb x 8 non-volatile static RAM and real-time
clock. The monolithic chip is available in a special package which provides a highly
integrated battery-backed memory and real-time clock solution.
The 44-lead, 330 mil SOIC package provides sockets with gold-plated contacts at both ends
for direct connection to a separate SNAPHAT housing containing the battery and crystal.
The unique design allows the SNAPHAT® battery/crystal package to be mounted on top of
the SOIC package after the completion of the surface mount process.
Insertion of the SNAPHAT housing after reflow prevents potential battery and crystal
damage due to the high temperatures required for device surface-mounting. The SNAPHAT
housing is keyed to prevent reverse insertion.
The SOIC and battery packages are shipped separately in plastic anti-static tubes or in tape
& reel form. For the 44-lead SOIC, the battery/crystal package (e.g., SNAPHAT) part
number is “M4T28-BR12SH” or “M4T32-BR12SH”.
Caution:
Do not place the SNAPHAT battery/crystal top in conductive foam, as this will drain the
lithium button-cell battery.
Figure 1.
Logic diagram
VCC
15
8
A0-A14
W
E
DQ0-DQ7
M48T37Y
M48T37V
RST
IRQ/FT
G
WDI
VSS
AI02172
Doc ID 7019 Rev 9
5/30
Description
M48T37Y, M48T37V
Table 1.
Signal names
A0-A14
Address inputs
DQ0-DQ7
Data inputs / outputs
RST
Reset output (open drain)
IRQ/FT
Interrupt / frequency test output (open drain)
WDI
Watchdog input
E
Chip enable
G
Output enable
W
WRITE enable
VCC
Supply voltage
VSS
Ground
NC
Not connected internally
Figure 2.
SOIC connections
NC
RST
NC
NC
A14
A12
A7
A6
A5
A4
A3
NC
NC
WDI
A2
A1
A0
DQ0
DQ1
DQ2
NC
VSS
44
1
2
43
3
42
4
41
40
5
39
6
38
7
8
37
36
9
35
10
11 M48T37Y 34
12 M48T37V 33
32
13
31
14
30
15
29
16
28
17
27
18
26
19
25
20
21
24
23
22
VCC
NC
NC
NC
IRQ/FT
W
A13
A8
A9
A11
G
NC
NC
A10
E
NC
DQ7
DQ6
DQ5
DQ4
DQ3
NC
AI02174
6/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Figure 3.
Description
Block diagram
IRQ/FT
WDI
OSCILLATOR AND
CLOCK CHAIN
16 x 8 BiPORT
SRAM ARRAY
32,768 Hz
CRYSTAL
POWER
A0-A14
LITHIUM
CELL
32,752 x 8
SRAM ARRAY
VOLTAGE SENSE
AND
SWITCHING
CIRCUITRY
VPFD
DQ0-DQ7
E
W
G
VCC
RST
Doc ID 7019 Rev 9
VSS
AI03253
7/30
Operation modes
2
M48T37Y, M48T37V
Operation modes
As Figure 3 on page 7 shows, the static memory array and the quartz controlled clock
oscillator of the M48T37Y/V are integrated on one silicon chip. The memory locations that
provide user accessible BYTEWIDE™ clock information are in the bytes with addresses
7FF1 and 7FF9h-7FFFh (located in Table 5 on page 13). The clock locations contain the
century, year, month, date, day, hour, minute, and second in 24-hour BCD format.
Corrections for 28, 29 (leap year - valid until the year 2100), 30, and 31 day months are
made automatically.
Byte 7FF8h is the clock control register. This byte controls user access to the clock
information and also stores the clock calibration setting.
Byte 7FF7h contains the watchdog timer setting. The watchdog timer redirects an out-ofcontrol microprocessor and provides a reset or interrupt to it. Bytes 7FF2h-7FF5h are
reserved for clock alarm programming. These bytes can be used to set the alarm. This will
generate an active low signal on the IRQ/FT pin when the alarm bytes match the date,
hours, minutes, and seconds of the clock. The eight clock bytes are not the actual clock
counters themselves; they are memory locations consisting of BiPORT™ READ/WRITE
memory cells. The M48T37Y/V includes a clock control circuit which updates the clock bytes
with current information once per second. The information can be accessed by the user in
the same manner as any other location in the static memory array.
The M48T37Y/V also has its own power-fail detect circuit. The control circuitry constantly
monitors the single VCC supply for an out of tolerance condition. When VCC is out of
tolerance, the circuit write protects the SRAM, providing a high degree of data security in the
midst of unpredictable system operation brought on by low VCC. As VCC falls below the
battery backup switchover voltage (VSO), the control circuitry connects the battery which
maintains data and clock operation until valid power returns.
Table 2.
Operating modes
Mode
VCC
Deselect
WRITE
READ
4.5 to 5.5 V
or
3.0 to 3.6 V
READ
Deselect
VSO to VPFD (min)
Deselect
≤
(1)
VSO(1)
E
G
W
DQ0-DQ7
Power
VIH
X
X
High Z
Standby
VIL
X
VIL
DIN
Active
VIL
VIL
VIH
DOUT
Active
VIL
VIH
VIH
High Z
Active
X
X
X
High Z
CMOS standby
X
X
X
High Z
Battery backup mode
1. See Table on page 23 for details.
Note:
X = VIH or VIL; VSO = Battery backup switchover voltage.
2.1
READ mode
The M48T37Y/V is in the READ mode whenever WRITE enable (W) is high and chip enable
(E) is low. The unique address specified by the 15 address inputs defines which one of the
32,752 bytes of data is to be accessed. Valid data will be available at the data I/O pins within
address access time (tAVQV) after the last address input signal is stable, providing that the E
and output enable (G) access times are also satisfied. If the E and G access times are not
8/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Operation modes
met, valid data will be available after the latter of the chip enable access time (tELQV) or
output enable access time (tGLQV).
The state of the eight three-state data I/O signals is controlled by E and G. If the outputs are
activated before tAVQV, the data lines will be driven to an indeterminate state until tAVQV.
If the address inputs are changed while E and G remain active, output data will remain valid
for output data hold time (tAXQX) but will be indeterminate until the next address access.
Figure 4.
READ mode AC waveforms
tAVAV
VALID
A0-A14
tAVQV
tAXQX
tELQV
tEHQZ
E
tELQX
tGLQV
tGHQZ
G
tGLQX
DQ0-DQ7
VALID
AI00925
Note:
WRITE enable (W) = high.
Table 3.
Symbol
READ mode AC characteristics
M48T37Y
M48T37V
–70
–100
Parameter(1)
Min
Max
Min
Unit
Max
tAVAV
READ cycle time
tAVQV
Address valid to output valid
70
100
ns
tELQV
Chip enable low to output valid
70
100
ns
tGLQV
Output enable low to output valid
35
50
ns
70
100
ns
tELQX(2)
Chip enable low to output transition
5
10
ns
tGLQX(2)
Output enable low to output transition
5
5
ns
tEHQZ(2)
Chip enable high to output Hi-Z
25
50
ns
tGHQZ(2)
Output enable high to output Hi-Z
25
40
ns
tAXQX
Address transition to output transition
10
10
ns
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
2. CL = 5 pF.
Doc ID 7019 Rev 9
9/30
Operation modes
2.2
M48T37Y, M48T37V
WRITE mode
The M48T37Y/V is in the WRITE mode whenever W and E are low. The start of a WRITE is
referenced from the latter occurring falling edge of W or E. A WRITE is terminated by the
earlier rising edge of W or E. The addresses must be held valid throughout the cycle. E or W
must return high for a minimum of tEHAX from chip enable or tWHAX from WRITE enable prior
to the initiation of another READ or WRITE cycle. Data-in must be valid tDVWH prior to the
end of WRITE and remain valid for tWHDX afterward. G should be kept high during WRITE
cycles to avoid bus contention; however, if the output bus has been activated by a low on E
and G, a low on W will disable the outputs tWLQZ after W falls.
Figure 5.
WRITE enable controlled, WRITE AC waveform
tAVAV
A0-A14
VALID
tAVWH
tAVEL
tWHAX
E
tWLWH
tAVWL
W
tWLQZ
tWHQX
tWHDX
DQ0-DQ7
DATA INPUT
tDVWH
AI00926
Figure 6.
Chip enable controlled, WRITE AC waveforms
tAVAV
VALID
A0-A14
tAVEH
tELEH
tAVEL
tEHAX
E
tAVWL
W
tEHDX
DATA INPUT
DQ0-DQ7
tDVEH
AI00927
10/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Table 4.
Symbol
Operation modes
WRITE mode AC characteristics
M48T37Y
M48T37V
–70
–100
Parameter(1)
Min
Max
Min
Unit
Max
tAVAV
WRITE cycle time
70
100
ns
tAVWL
Address valid to WRITE enable low
0
0
ns
tAVEL
Address valid to chip enable low
0
0
ns
tWLWH
WRITE enable pulse width
50
80
ns
tELEH
Chip enable low to chip enable high
55
80
ns
tWHAX
WRITE enable high to address transition
0
10
ns
tEHAX
Chip enable high to address transition
0
10
ns
tDVWH
Input valid to WRITE enable high
30
50
ns
tDVEH
Input valid to chip enable high
30
50
ns
tWHDX
WRITE enable high to input transition
5
5
ns
tEHDX
Chip enable high to input transition
5
5
ns
tWLQZ(2)(3)
WRITE enable low to output Hi-Z
25
50
ns
tAVWH
Address valid to WRITE enable high
60
80
ns
tAVEH
Address valid to chip enable high
60
80
ns
WRITE enable high to output transition
5
10
ns
tWHQX
(2)(3)
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
2. CL = 5 pF.
3. If E goes low simultaneously with W going low, the outputs remain in the high impedance state.
2.3
Data retention mode
With valid VCC applied, the M48T37Y/V operates as a conventional BYTEWIDE™ static
RAM. Should the supply voltage decay, the RAM will automatically power-fail deselect, write
protecting itself when VCC falls within the VPFD (max), VPFD (min) window. All outputs
become high impedance, and all inputs are treated as “Don't care.”
Note:
A power failure during a WRITE cycle may corrupt data at the currently addressed location,
but does not jeopardize the rest of the RAM's content. At voltages below VPFD (min), the
user can be assured the memory will be in a write protected state, provided the VCC fall time
is not less than tF.
The M48T37Y/V may respond to transient noise spikes on VCC that reach into the deselect
window during the time the device is sampling VCC. Therefore, decoupling of the power
supply lines is recommended. When VCC drops below VSO, the control circuit switches
power to the internal battery which preserves data and powers the clock. The internal button
cell will maintain data in the M48T37Y/V for an accumulated period of at least 7 years at
room temperature when VCC is less than VSO. As system power returns and VCC rises
above VSO, the battery is disconnected and the power supply is switched to external VCC.
Normal RAM operation can resume tREC after VCC reaches VPFD (max).
For more information on battery storage life refer to the application note AN1012.
Doc ID 7019 Rev 9
11/30
Clock operations
3
Clock operations
3.1
Reading the clock
M48T37Y, M48T37V
Updates to the TIMEKEEPER® registers should be halted before clock data is read to
prevent reading data in transition. The BiPORT™ TIMEKEEPER cells in the RAM array are
only data registers and not the actual clock counters, so updating the registers can be halted
without disturbing the clock itself.
Updating is halted when a '1' is written to the READ bit, D6 in the control register 7FF8h. As
long as a '1' remains in that position, updating is halted. After a halt is issued, the registers
reflect the count; that is, the day, date, and the time that were current at the moment the halt
command was issued.
All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an
update in progress. Updating will resume within a second after the bit is reset to a '0.'
3.2
Setting the clock
Bit D7 of the control register (7FF8h) is the WRITE bit. Setting the WRITE bit to a '1,' like the
READ bit, halts updates to the TIMEKEEPER registers. The user can then load them with
the correct day, date, and time data in 24-hour BCD format (see Table 5 on page 13).
Resetting the WRITE bit to a '0' then transfers the values of all time registers (7FF1h,
7FF9h-7FFFh) to the actual TIMEKEEPER counters and allows normal operation to
resume. After the WRITE bit is reset, the next clock update will occur in approximately one
second.
Note:
Upon power-up following a power failure, both the WRITE bit and the READ bit will be reset
to '0.'
3.3
Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the
oscillator. When reset to a '0,' the M48T37Y/V oscillator starts within one second.
Note:
12/30
It is not necessary to set the WRITE bit when setting or resetting the FREQUENCY TEST
bit (FT) or the STOP bit (ST).
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Table 5.
Clock operations
Register map
Data
Address
D7
D6
7FFEh
0
0
7FFDh
0
0
7FFCh
0
FT
7FFBh
0
0
7FFAh
0
7FF9h
ST
7FF8h
W
R
S
7FF7h
WDS
BMB4
BMB3
7FF6h
AFE
0
ABE
7FF5h
RPT4
0
AIarm 10 date
Alarm date
Alarm date
01-31
7FF4h
RPT3
0
AIarm 10 hours
Alarm hours
Alarm hour
00-23
7FF3h
RPT2
Alarm 10 minutes
Alarm minutes
Alarm min
00-59
7FF2h
RPT1
Alarm 10 seconds
Alarm seconds
Alarm sec
00-59
100 year
Century
00-99
7FFFh
D4
D3
D2
10 years
7FF1h
7FF0h
D5
D0
Year
Year
00-99
Month
Month
01-12
Date: Day of month
Date
01-31
Day of week
Day
01-7
Hours
Hours
00-23
10 minutes
Minutes
Min
00-59
10 seconds
Seconds
Sec
00-59
0
10 M
10 date
0
0
0
10 hours
Calibration
BMB2 BMB1 BMB0
0
0
1000 year
WDF
D1
Function/range
BCD format
AF
Z
BL
Z
0
Z
Control
RB1
RB0
Watchdog
0
0
Interrupts
Z
Z
Flags
Keys:
S = Sign bit
FT = Frequency test bit
R = READ bit
W = WRITE bit
ST = Stop bit
0 = Must be set to '0'
BL = Battery low flag (read only)
BMB0-BMB4 = Watchdog multiplier bits
AFE = Alarm flag enable flag
RB0-RB1 = Watchdog resolution bits
WDS = Watchdog steering bit
ABE = Alarm in battery backup mode enable bit
RPT1-RPT4 = Alarm repeat mode bits
WDF = Watchdog flag (read only)
AF = Alarm flag (read only)
Z = '0' and are read only
Doc ID 7019 Rev 9
13/30
Clock operations
3.4
M48T37Y, M48T37V
Setting the alarm clock
Registers 7FF5h-7FF2h contain the alarm settings. The alarm can be configured to go off at
a predetermined time on a specific day of the month or repeat every day, hour, minute, or
second. It can also be programmed to go off while the M48T37Y/V is in the battery backup
mode of operation to serve as a system wake-up call.
RPT1-RPT4 put the alarm in the repeat mode of operation. Table 6 shows the possible
configurations. Codes not listed in the table default to the once per second mode to quickly
alert the user of an incorrect alarm setting.
Note:
User must transition address (or toggle chip enable) to see flag bit change.
When the clock information matches the alarm clock settings based on the match criteria
defined by RPT1-RPT4, AF is set. If AFE is also set, the alarm condition activates the
IRQ/FT pin. To disable alarm, write '0' to the alarm date registers and RPT1-4. The alarm
flag and the IRQ/FT output are cleared by a READ to the flags register as shown in Figure 7.
A subsequent READ of the flags register is necessary to see that the value of the alarm flag
has been reset to '0.'
The IRQ/FT pin can also be activated in the battery backup mode. The IRQ/FT will go low if
an alarm occurs and both the alarm in battery backup mode enable (ABE) and the AFE are
set. The ABE and AFE bits are reset during power-up, therefore an alarm generated during
power-up will only set AF. The user can read the flag register at system boot-up to
determine if an alarm was generated while the M48T37Y/V was in the deselect mode during
power-up. Figure 8 illustrates the backup mode alarm timing.
Figure 7.
Alarm interrupt reset waveform
ADDRESS 7FF0h
A0-A14
15ns Min
ACTIVE FLAG BIT
IRQ/FT
AI01677B
Table 6.
14/30
Alarm repeat modes
RPT4
RPT3
RPT2
RPT1
Alarm activated
1
1
1
1
Once per second
1
1
1
0
Once per minute
1
1
0
0
Once per hour
1
0
0
0
Once per day
0
0
0
0
Once per month
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Figure 8.
Clock operations
Backup mode alarm waveforms
tREC
VCC
VPFD (max)
VPFD (min)
VSO
ABE, AFE bit in Interrupt Register
AF bit in Flags Register
IRQ/FT
HIGH-Z
HIGH-Z
AI03254B
3.5
Calibrating the clock
The M48T37Y/V is driven by a quartz controlled oscillator with a nominal frequency of
32,768 Hz. The devices are tested not to exceed ±35 ppm (parts per million) oscillator
frequency error at 25 °C, which equates to about ±1.53 minutes per month. With the
calibration bits properly set, the accuracy of each M48T37Y/V improves to better than
+1/–2 ppm at 25 °C.
The oscillation rate of any crystal changes with temperature (see Figure 10 on page 19).
Most clock chips compensate for crystal frequency and temperature shift error with
cumbersome trim capacitors. The M48T37Y/V design, however, employs periodic counter
correction. The calibration circuit adds or subtracts counts from the oscillator divider circuit
at the divide by 256 stage, as shown in Figure 11 on page 19. The number of times pulses
are blanked (subtracted, negative calibration) or split (added, positive calibration) depends
upon the value loaded into the five-bit calibration byte found in the control register. Adding
counts speeds the clock up, subtracting counts slows the clock down.
The calibration byte occupies the five lower order bits (D4-D0) in the control register 7FF8h.
These bits can be set to represent any value between 0 and 31 in binary form. Bit D5 is the
sign bit; '1' indicates positive calibration, '0' indicates negative calibration. Calibration occurs
within a 64 minute cycle. The first 62 minutes in the cycle may, once per minute, have one
second either shortened by 128 or lengthened by 256 oscillator cycles. If a binary '1' is
loaded into the register, only the first 2 minutes in the 64 minute cycle will be modified; if a
binary 6 is loaded, the first 12 will be affected, and so on.
Therefore, each calibration step has the effect of adding 512 or subtracting 256 oscillator
cycles for every 125, 829, 120 (64 minutes x 60 seconds/minute x 32,768 cycles/second)
actual oscillator cycles, that is +4.068 or –2.034 ppm of adjustment per calibration step in
the calibration register. Assuming that the oscillator is in fact running at exactly 32,768 Hz,
each of the 31 increments in the calibration byte would represent +10.7 or –5.35 seconds
per month which corresponds to a total range of +5.5 or –2.75 minutes per month.
Doc ID 7019 Rev 9
15/30
Clock operations
M48T37Y, M48T37V
Two methods are available for ascertaining how much calibration a given M48T37Y/V may
require. The first involves simply setting the clock, letting it run for a month and comparing it
to a known accurate reference (like WWW broadcasts). While that may seem crude, it
allows the designer to give the end user the ability to calibrate his clock as his environment
may require, even after the final product is packaged in a non-user serviceable enclosure.
All the designer has to do is provide a simple utility that accesses the calibration byte.
The second approach is better suited to a manufacturing environment, and involves the use
of the IRQ/FT pin. The pin will toggle at 512 Hz when the stop bit (ST, D7 of 7FF9h) is '0' the
frequency test bit (FT, D6 of 7FFCh) is '1,' the alarm flag enable bit (AFE, D7 of 7FF6h) is '0,'
and the watchdog steering bit (WDS, D7 of 7FF7h) is '1' or the watchdog register is reset
(7FF7h=0).
Any deviation from 512 Hz indicates the degree and direction of oscillator frequency shift at
the test temperature. For example, a reading of 512.01024 Hz would indicate a +20 ppm
oscillator frequency error, requiring a –10(WR001010) to be loaded into the calibration byte
for correction.
Note:
Setting or changing the calibration byte does not affect the frequency test output frequency.
The IRQ/FT pin is an open drain output which requires a pull-up resistor for proper
operation. A 500-10 kΩ resistor is recommended in order to control the rise time. The FT bit
is cleared on power-down.
For more information on calibration, see the application note AN934, “TIMEKEEPER
calibration.”
3.6
Watchdog timer
The watchdog timer can be used to detect an out-of-control microprocessor. The user
programs the watchdog timer by setting the desired amount of time-out into the eight-bit
watchdog register, address 7FF7h. The five bits (BMB4-BMB0) that store a binary multiplier
and the two lower order bits (RB1-RB0) select the resolution, where 00 = 1/16 second,
01 = 1/4 second, 10 = 1 second, and 11 = 4 seconds. The amount of time-out is then
determined to be the multiplication of the five-bit multiplier value with the resolution. (For
example: writing 00001110 in the watchdog register = 3x1, or 3 seconds).
Note:
Accuracy of timer is within ± the selected resolution.
If the processor does not reset the timer within the specified period, the M48T37Y/V sets the
watchdog flag (WDF) and generates a watchdog interrupt or a microprocessor reset. WDF
is reset by reading the flags register (Address 7FF0h).
Note:
User must transition address (or toggle chip enable) to see flag bit change.
Reset will not occur unless the addresses are stable at the flag location for at least 15 ns
while the device is in the READ mode as shown in Figure 9 on page 19.
The most significant bit of the watchdog register is the watchdog steering bit. When set to a
'0,' the watchdog will activate the IRQ/FT pin when timed-out. When WDS is set to a '1,' the
watchdog will output a negative pulse on the RST pin for a duration of tREC. The watchdog
register, the FT bit, AFE bit, and ABE bit will reset to a '0' at the end of a watchdog time-out
when the WDS bit is set to a '1.'
The watchdog timer resets when the microprocessor performs a re-write of the watchdog
register or an edge transition (low to high / high to low) on the WDI pin occurs. The timeout
period then starts over.
16/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Clock operations
The watchdog timer is disabled by writing a value of 00000000 to the eight bits in the
watchdog register. Should the watchdog timer time out, a value of 00h needs to be written to
the watchdog register in order to clear the IRQ/FT pin.
The watchdog function is automatically disabled upon power-down and the watchdog
register is cleared. If the watchdog function is set to output to the IRQ/FT pin and the
frequency test function is activated, the watchdog or alarm function prevails and the
frequency test function is denied. The WDI pin should be connected to VSS if not used.
3.7
Power-on reset
The M48T37Y/V continuously monitors VCC. When VCC falls to the power fail detect trip
point, the RST pulls low (open drain) and remains low on power-up for tREC after VCC
passes VPFD. RST is valid for all VCC conditions. The RST pin is an open drain output and
an appropriate resistor to VCC should be chosen to control rise time (see Figure 13 on
page 22).
3.8
Programmable interrupts
The M48T37Y/V provides two programmable interrupts: an alarm and a watchdog. When an
interrupt condition occurs, the M48T37Y/V sets the appropriate flag bit in the flag register
7FF0h. The interrupt enable bits (AFE and ABE) in 7FF6h and the watchdog steering
(WDS) bit in 7FF7h allow the interrupt to activate the IRQ/FT pin.
The alarm flag and the IRQ/FT output are cleared by a READ to the flags register. An
interrupt condition reset will not occur unless the addresses are stable at the flag location for
at least 15 ns while the device is in the READ mode as shown in Figure 7 on page 14.
The IRQ/FT pin is an open drain output and requires a pull-up resistor (10 kΩ
recommended) to VCC. The pin remains in the high impedance state unless an interrupt
occurs or the frequency test mode is enabled.
Doc ID 7019 Rev 9
17/30
Clock operations
3.9
M48T37Y, M48T37V
Battery low flag
The M48T37Y/V automatically performs periodic battery voltage monitoring upon power-up.
The battery low flag (BL), bit D4 of the flags register 7FF0h, will be asserted high if the
SNAPHAT® battery is found to be less than approximately 2.5 V. The BL flag will remain
active until completion of battery replacement and subsequent battery low monitoring tests
during the next power-up sequence.
If a battery low is generated during a power-up sequence, this indicates the battery voltage
is below 2.5 V (approximately), which may be insufficient to maintain data integrity. Data
should be considered suspect and verified as correct. A fresh battery should be installed.
The SNAPHAT top may be replaced while VCC is applied to the device.
Note:
This will cause the clock to lose time during the interval the battery/crystal is removed.
Battery monitoring is a useful technique only when performed periodically. The M48T37Y/V
only monitors the battery when a nominal VCC is applied to the device. Thus applications
which require extensive durations in the battery back-up mode should be powered-up
periodically (at least once every few months) in order for this technique to be beneficial.
Additionally, if a battery low is indicated, data integrity should be verified upon power-up via
a checksum or other technique.
3.10
Initial power-on defaults
Upon application of power to the device, the following register bits are set to a '0' state:
WDS; BMB0-BMB4; RB0-RB1; AFE; ABE; W; R; and FT (see Table 7).
Table 7.
Default values
Condition
W
R
FT
AFE
ABE
Watchdog
register(1)
Initial power-up
(Battery attach for SNAPHAT®)(2)
0
0
0
0
0
0
Subsequent power-up / RESET(3)
0
0
0
0
0
0
0
0
0
1
1
0
Power-down
(4)
1. WDS, BMB0-BMB4, RBO, RB1.
2. State of other control bits undefined.
3. State of other control bits remains unchanged.
4. Assuming these bits set to '1' prior to power-down.
3.11
VCC noise and negative going transients
ICC transients, including those produced by output switching, can produce voltage
fluctuations, resulting in spikes on the VCC bus. These transients can be reduced if
capacitors are used to store energy which stabilizes the VCC bus. The energy stored in the
bypass capacitors will be released as low going spikes are generated or energy will be
absorbed when overshoots occur. A ceramic bypass capacitor value of 0.1 µF (as shown in
Figure 9) is recommended in order to provide the needed filtering.
In addition to transients that are caused by normal SRAM operation, power cycling can
generate negative voltage spikes on VCC that drive it to values below VSS by as much as
18/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Clock operations
one volt. These negative spikes can cause data corruption in the SRAM while in battery
backup mode. To protect from these voltage spikes, it is recommended to connect a
Schottky diode from VCC to VSS (cathode connected to VCC, anode to VSS). Schottky diode
1N5817 is recommended for through hole and MBRS120T3 is recommended for surface
mount.
Figure 9.
Supply voltage protection
VCC
VCC
0.1µF
DEVICE
VSS
AI02169
Figure 10. Crystal accuracy across temperature
Frequency (ppm)
20
0
–20
–40
–60
–80
–100
ΔF = -0.038 ppm (T - T )2 ± 10%
0
F
C2
–120
T0 = 25 °C
–140
–160
–40
–30
–20
–10
0
10
20
30
Temperature °C
40
50
60
70
80
AI00999
Figure 11. Clock calibration
NORMAL
POSITIVE
CALIBRATION
NEGATIVE
CALIBRATION
AI00594B
Doc ID 7019 Rev 9
19/30
Maximum ratings
4
M48T37Y, M48T37V
Maximum ratings
Stressing the device above the rating listed in the absolute maximum ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Table 8.
Absolute maximum ratings
Symbol
TA
TSTG
TSLD(1)
Parameter
Ambient operating temperature
Storage temperature (VCC off,
oscillator off)
Value
Unit
Grade 1
0 to 70
°C
Grade 6
–40 to 85
°C
SNAPHAT®
–40 to 85
°C
SOH44
–55 to 150
°C
260
°C
M48T37Y
–0.3 to 7
V
M48T37V
–0.3 to 4.6
V
M48T37Y
–0.3 to 7
V
M48T37V
–0.3 to 4.6
V
Lead solder temperature for 10 seconds
VIO
Input or output voltages
VCC
Supply voltage
IO
Output current
10
mA
PD
Power dissipation
1
W
1. For SOH44 package, lead-free (Pb-free) lead finish: reflow at peak temperature of 260 °C (the time above
255 °C must not exceed 30 seconds).
Caution:
Negative undershoots below –0.3 V are not allowed on any pin while in the battery backup
mode.
Caution:
Do NOT wave solder SOIC to avoid damaging SNAPHAT® sockets.
20/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
5
DC and AC parameters
DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC characteristic
tables are derived from tests performed under the measurement conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Table 9.
Operating and AC measurement conditions
Parameter
Supply voltage (VCC)
M48T37Y
M48T37V
Unit
4.5 to 5.5
3.0 to 3.6
V
Grade 1
0 to 70
0 to 70
°C
Grade 6
–40 to 85
–40 to 85
°C
Load capacitance (CL)
100
50
pF
Input rise and fall times
≤ 10
≤ 10
ns
Input pulse voltages
0 to 3
0 to 3
V
1.5
1.5
V
Ambient operating temperature (TA)
Input and output timing ref. voltages
Note:
Output Hi-Z is defined as the point where data is no longer driven.
Figure 12. AC testing load circuit
645Ω
DEVICE
UNDER
TEST
(1)
CL = 100pF
1.75V
CL includes JIG capacitance
AI02325
1. 50 pF for M48T37V.
Note:
Excluding open-drain output pins
Table 10.
Capacitance
Symbol
Parameter(1)(2)
Min
Max
Unit
CIN
Input capacitance
-
10
pF
Input / output capacitance
-
10
pF
CIO
(3)
1. Effective capacitance measured with power supply at 5 V. Sampled only, not 100% tested.
2. At 25 °C, f = 1 MHz.
3. Outputs deselected.
Doc ID 7019 Rev 9
21/30
DC and AC parameters
Table 11.
M48T37Y, M48T37V
DC characteristics
Symbol
Parameter
M48T37Y
M48T37V
–70
–100
Test condition(1)
Min
ILI(2)
ILO
(3)
Input leakage current
Output leakage current
Max
Min
Unit
Max
0 V ≤ VIN ≤ VCC
±1
±1
µA
0 V ≤ VOUT ≤ VCC
±1
±1
µA
Outputs open
50
33
mA
E = VIH
3
2
mA
E = VCC – 0.2 V
3
2
mA
ICC
Supply current
ICC1
Supply current (standby) TTL
ICC2
Supply current (standby)
CMOS
VIL
Input low voltage
–0.3
0.8
–0.3
0.8
V
VIH
Input high voltage
2.2
VCC + 0.3
2.2
VCC + 0.3
V
Output low voltage (standard)
IOL = 2.1 mA
0.4
0.4
V
VOL
Output low voltage
(open drain)
IOL = 10 mA
0.4
0.4
V
VOH
Output high voltage
IOH = –1 mA
2.4
2.4
V
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V (except where
noted).
2. WDI internally pulled down to VSS through a 100 kΩ resistor.
3. Outputs deselected.
Figure 13. Power down/up mode AC waveforms
VCC
VPFD (max)
VPFD (min)
VSO
tF
tR
tFB
tRB
tDR
tREC
RST
INPUTS
VALID
OUTPUTS
VALID
DON'T CARE
VALID
HIGH-Z
VALID
AI03078
22/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
Table 12.
DC and AC parameters
Power down/up AC characteristics
Parameter(1)
Symbol
Min
Max
Unit
tF(2)
VPFD (max) to VPFD (min) VCC fall time
300
µs
tFB(3)
VPFD (min) to VSS VCC fall time
10
µs
VPFD (min) to VPFD (max) VCC rise time
10
µs
VSS to VPFD (min) VCC rise time
1
µs
VPFD (max) to RST high
40
tR
tRB
tREC
(4)
200
ms
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
2. VPFD (max) to VPFD (min) fall time of less than tF may result in deselection/write protection not occurring
until 200 µs after VCC passes VPFD (min).
3. VPFD (min) to VSS fall time of less than tFB may cause corruption of RAM data
4. tREC (min) = 20 ms for industrial temperature range - grade 6 device.
Table 13.
Power down/up trip points DC characteristics
Parameter(1)
Symbol
VPFD
Power-fail deselect voltage
VSO
Battery backup switchover voltage
tDR(2)
Expected data retention time
Min
Typ
Max
Unit
M48T37Y
4.2
4.4
4.5
V
M48T37V
2.7
2.9
3.0
V
M48T37Y
VBAT
V
M48T37V
VPFD –100 mV
V
7
Years
Grade 1
5
Grade 6
10(3)
Years
1. Valid for ambient operating temperature: TA = 0 to 70 °C or –40 to 85 °C; VCC = 4.5 to 5.5 V or 3.0 to 3.6 V
(except where noted).
2. At 25 °C, VCC = 0 V.
3. Using larger M4T32-BR12SH6 SNAPHAT® top (recommended for industrial temperature range - grade 6
device).
Note:
All voltages referenced to VSS.
Doc ID 7019 Rev 9
23/30
Package mechanical data
6
M48T37Y, M48T37V
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 14. SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT® outline
A2
A
C
B
eB
e
CP
D
N
E
H
A1
α
L
1
SOH-A
Note:
Drawing is not to scale.
Table 14.
SOH44 – 44-lead plastic small outline, 4-socket SNAPHAT®, package
mechanical data
mm
inches
Symbol
Typ
Min
A
Typ
Min
3.05
Max
0.120
A1
0.05
0.36
0.002
0.014
A2
2.34
2.69
0.092
0.106
B
0.36
0.46
0.014
0.018
C
0.15
0.32
0.006
0.012
D
17.71
18.49
0.697
0.728
E
8.23
8.89
0.324
0.350
–
–
–
–
eB
3.20
3.61
0.126
0.142
H
11.51
12.70
0.453
0.500
L
0.41
1.27
0.016
0.050
a
0°
8°
0°
8°
N
44
e
CP
24/30
Max
0.81
0.032
44
0.10
Doc ID 7019 Rev 9
0.004
M48T37Y, M48T37V
Package mechanical data
Figure 15. SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, pack. outline
A1
A2
A
A3
eA
B
L
eB
D
E
SHTK-A
Note:
Drawing is not to scale.
Table 15.
SH – 4-pin SNAPHAT® housing for 48 mAh battery & crystal, package
mechanical data
mm
inches
Symbol
Typ
Min
A
Max
Typ
Min
9.78
Max
0.385
A1
6.73
7.24
0.265
0.285
A2
6.48
6.99
0.255
0.275
A3
B
0.38
0.46
0.56
0.015
0.018
0.022
D
21.21
21.84
0.835
0.860
E
14.22
14.99
0.560
0.590
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
Doc ID 7019 Rev 9
25/30
Package mechanical data
M48T37Y, M48T37V
Figure 16. SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, pack. outline
A1
A2
A
A3
eA
B
L
eB
D
E
SHTK-A
Note:
Drawing is not to scale.
Table 16.
SH – 4-pin SNAPHAT® housing for 120 mAh battery & crystal, package
mechanical data
mm
inches
Symbol
Typ
Min
A
Typ
Min
10.54
Max
0.415
A1
8.00
8.51
0.315
.0335
A2
7.24
8.00
0.285
0.315
A3
26/30
Max
0.38
0.015
B
0.46
0.56
0.018
0.022
D
21.21
21.84
0.835
0.860
E
17.27
18.03
0.680
.0710
eA
15.55
15.95
0.612
0.628
eB
3.20
3.61
0.126
0.142
L
2.03
2.29
0.080
0.090
Doc ID 7019 Rev 9
M48T37Y, M48T37V
7
Part numbering
Part numbering
Table 17.
Ordering information scheme
Example:
M48T
37Y
–70
MH
1
E
Device type
M48T
Supply voltage and write protect voltage
37Y = VCC = 4.5 to 5.5 V; VPFD = 4.2 to 4.5 V
37V = VCC = 3.0 to 3.6 V; VPFD = 2.7 to 3.0 V
Speed
–70 = 70 ns (37Y)
–10 = 100 ns (37V)
Package
MH(1) = SOH44
Temperature range
1 = 0 to 70 °C
6 = –40 to 85 °C(2)
Shipping method
blank = tubes (not for new design - use E)
E = ECOPACK® package, tubes
F = ECOPACK® package, tape & reel
TR = tape & reel (not for new design - use F)
1. The SOIC package (SOH44) requires the SNAPHAT® battery package which is ordered separately under
the part number “M4TXX-BR12SH” in plastic tube or “M4TXX-BR12SHTR” in tape & reel form (see
Table ).
2. Not recommended for new design. Contact ST sales office for availability.
Caution:
Do not place the SNAPHAT battery package “M4TXX-BR12SH” in conductive foam as it will
drain the lithium button-cell battery.
For other options, or for more information on any aspect of this device, please contact the
ST sales office nearest you.
Table 18.
SNAPHAT® battery table
Part number
Description
M4T28-BR12SH
Lithium battery (48 mAh) SNAPHAT®
SH
M4T32-BR12SH
SNAPHAT®
SH
Lithium battery (120 mAh)
Doc ID 7019 Rev 9
Package
27/30
Environmental information
8
M48T37Y, M48T37V
Environmental information
Figure 17. Recycling symbols
This product contains a non-rechargeable lithium (lithium carbon monofluoride chemistry)
button cell battery fully encapsulated in the final product.
Recycle or dispose of batteries in accordance with the battery manufacturer's instructions
and local/national disposal and recycling regulations.
Please refer to the following web site address for additional information regarding
compliance statements and waste recycling.
Go to www.st.com/rtc, then select "Lithium Battery Recycling" from "Related Topics".
28/30
Doc ID 7019 Rev 9
M48T37Y, M48T37V
9
Revision history
Revision history
Table 19.
Document revision history
Date
Revision
Changes
Dec-1999
1
First issue
07-Feb-2000
2
From preliminary data to datasheet; battery low flag paragraph
changed; 100 ns speed class identifier changed (Table , 4)
11-Jul-2000
2.1
19-Jun-2001
3
06-Aug-2001
3.1
Fix text for setting the alarm clock (Figure 7)
15-Jan-2002
3.2
Fix footnote numbering (Table )
20-May-2002
3.3
Modify reflow time and temperature footnote (Table 8)
31-Mar-2003
4
v2.2 template applied; data retention condition updated (Table )
01-Apr-2004
5
Reformatted; updated with lead-free package information (Table 8, )
08-Feb-2006
6
New template; updated lead-free text; fixed DC characteristics (Table 8,
11, )
03-Aug-2007
7
Reformatted; added lead-free second level interconnect information to
cover page and Section 6: Package mechanical data.
24-Mar-2009
8
Updated Table 8; Section 6: Package mechanical data; added
Section 8: Environmental information; minor reformatting.
02-Aug-2010
9
Updated Features, Section 4, Table 17; reformatted document; minor
textual changes.
tFB changed (Table ); watchdog timer paragraph changed
Reformatted; added temp./voltage info. to tables (Table 10, 11, , 4, , )
Doc ID 7019 Rev 9
29/30
M48T37Y, M48T37V
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
30/30
Doc ID 7019 Rev 9