RGP10A - RGP10M FAST RECOVERY RECTIFIERS DO - 41 PRV : 50 - 1000 Volts Io : 1.0 Ampere FEATURES : * * * * * * 1.00 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) High current capability High reliability Low reverse current Low forward voltage drop Fast switching for high efficiency Pb / RoHS Free 0.205 (5.2) 0.166 (4.2) MECHANICAL DATA : 1.00 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) * Case : DO-41 Molded plastic * Epoxy : UL94V-O rate flame retardant * Lead : Axial lead solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Color band denotes cathode end * Mounting position : Any * Weight : 0.339 gram Dimensions in inches and ( millimeters ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. SYMBOL RGP 10A RGP 10B RGP 10D RGP 10G RGP 10J RGP 10K RGP 10M UNIT Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 V Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 V VDC 50 100 200 400 600 800 1000 V RATING Maximum DC Blocking Voltage Maximum Average Forward Current 0.375"(9.5mm) Lead Length Ta = 55 °C Peak Forward Surge Current, 8.3ms Single half sine wave Superimposed on rated load (JEDEC Method) Maximum Peak Forward Voltage at IF = 1.0 A Maximum Full load Reverse Current, Full Cycle Average 0.375",(9.5mm) Lead Length Ta = 55°C Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 150 °C Maximum Reverse Recovery Time ( Note 1 ) IF(AV) 1.0 A IFSM 30 A VF 1.3 V IR(AV) 100 µA IR 5.0 IR(H) 200 µA µA Trr 150 250 500 ns CJ 15 pf 50 °C/W Junction Temperature Range RθJA TJ - 65 to + 175 °C Storage Temperature Range TSTG - 65 to + 175 °C Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance ( Note 3 ) Notes : ( 1 ) Reverse Recovery Test Conditions : IF = 0.5 A, IR = 1.0 A, Irr = 0.25 A. ( 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 VDC ( 3 ) Thermal Resistance from Junction to Ambient at 0.375" (9.5mm) Lead Lengths, P.C. Board Mounted. Page 1 of 2 Rev. 02 : March 25, 2005 RATING AND CHARACTERISTIC CURVES ( RGP10A - RGP10M ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω Trr 10 Ω + 0.5 D.U.T. + 0 PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx.) 1Ω - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF. 1 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.0 0.8 0.6 TJ = 25 °C 0.4 0.2 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTHS 0 0 25 50 75 100 125 150 24 18 12 6 0 175 8.3 ms SINGLE HALF SINE-WAVE (JEDEC) METHOD TJ = TJ max. 1 AMBIENT TEMPERATURE, ( °C) Pulse W idth = 300 µs 2% Duty Cycle TJ = 25 °C 1.0 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE, VOLTS Page 2 of 2 6 10 20 40 60 100 1.8 2.0 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES 10 0.2 4 NUMBER OF CYCLES AT 60Hz FIG.4 - TYPICAL FORWARD CHARACTERISTICS 0 2 10 TJ = 100 °C 1.0 0.1 TJ = 25 °C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 02 : March 25, 2005