R2500F THRU R5000F HIGH VOLTAGE FAST RECOVERY RECTIFIER Reverse Voltage - 2500 to 5000 Volts The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Construction utilizes void-free molded plastic technique Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 1.0 (25.4) MIN. 0.140 (3.6) 0.104(2.6) DIA. 0.300(7.6) 0.230(5.8) 0.205 (5.2) 0.160(4.1) MECHANICAL DATA 1.0 (25.4) MIN. 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. FEATURES DO-15 DO-41 0.107 (2.7) 0.080 (2.0) DIA. Forward Current - 0.2 Ampere Case: JEDEC DO-41/DO-15 molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight:0.012 ounce, 0.33 grams(DO-41) 0.014 ounce, 0.40 grams(DO-15) 0.034 (0.86) 0.028 (0.71) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. SYMBOLS R2500F R3000F R4000F R5000F UNITS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375”(9.5mm) lead length (see fig.1) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 0.2 A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) VRRM VRMS VDC 2500 1750 2500 3000 2100 3000 4000 2800 4000 5000 3500 5000 VOLTS VOLTS VOLTS Typical thermal resistance (NOTE 3) Operating junction and storage temperature range RqJA TJ,TSTG I(AV) 0.2 Amp IFSM 30.0 Amps VF 4.0 IR 6.5 5.0 5.0 50.0 Volts uA trr 500 ns CJ 15.0 50.0 -65 to +150 pF C/W C Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.Thermal resistance from junction to ambient at 0.375”(9.5mm)lead length,P.C.B. mounted www.shunyegroup.com FIG. 1- FORWARD CURRENT DERATING CURVE 0.25 0.20 0.15 0.10 Single Phase Half Wave 60Hz Resistive or inductive Load 0.05 0 0 25 50 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 £PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES R2500F THRU R5000F 75 100 125 150 25 20 15 10 175 5.0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C FIG. 4-TYPICAL REVERSE CHARACTERISTICS FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 1 0.1 0.01 R2500F R3000F R4000F-R5000F 0.001 1.0 2.0 3.0 4.0 5.0 5.5 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 2 100 10 TJ=100 C 1 0.1 0.01 TJ=25 C 0 INSTANTANEOUS FORWARD VOLEAGE, VOLTS 40 60 80 TJ=25 C 10 100 10 1 0.1 0.01 0.1 1 10 1 0.1 1.0 10 100 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W FIG. 5-TYPICAL JUNCTION CAPACITANCE 100 20 PERCENT OF PEAK REVERSE VOLTAGE,% 200 JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS www.shunyegroup.com t,PULSE DURATION,sec. 100