TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 1. Description 1.1 Feature The Transcend CF 80X is a High Speed Compact • RoHS compliant products Flash Card with high quality Flash Memory assembled • Compliant with CompactFlash® specification V3.0 on a printed circuit board. • Single Power Supply: 5V ± 10% / 3.3V ± 5% • Compliant to CompactFlash, PCMCIA, and ATA standards Placement • Support PIO mode 0 to PIO mode 6 • Support Multi-Word DMA mode 0 to Multi-Word DMA mode 4 (Series of –P only supports PIO mode 0 to mode 4, please see Ordering Information) • True IDE Mode: Fixed Disk (Standard) • PC Card Mode: Removable Disk (Standard) o o • Operating Temperature: -25 C to 85 C o o • Storage Temperature: -40 C to 85 C • Hardware RS-code ECC • Support Wear-Leveling to extend product life • Durability of Connector: 10,000 times 1.2 Dimensions Transcend Information Inc. 1 Side Millimeters Inches A 36.40 ± 0.150 1.43 ± 0.005 B 42.80 ± 0.100 1.69 ± 0.004 C 3.30 ± 0.100 0.13 ± 0.004 D 0.63 ± 0.070 0.02 ± 0.003 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 1.3 Ordering Information Part Number TS32M~1GCF80 CF80 TS32M~1GCF80-P Mode True IDE mode PCMCIA mode Description Transfer mode DMA Fixed Disk Multiword DMA mode 0~4, PIO mode 0~6 Non-DMA Removable Disk N/A True IDE mode PCMCIA mode Non-DMA Fixed Disk Non-DMA Removable Disk PIO mode 0~4 N/A 1.4 CHS and Capacity Product Name Cylinder Head Sector Capacity TS32MCF80 62 16 63 29.9MB TS64MCF80 125 16 63 60.8MB TS128MCF80 246 16 63 120MB TS256MCF80 500 16 63 245MB TS512MCF80 989 16 63 486MB TS1GCF80 1978 16 63 972MB Transcend Information Inc. 2 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 2.Product Specification 2.1 Compactflash Card Specification Transcend Transcend Information Inc. 3 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 2.2 Block Diagram Transcend Information Inc. 4 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3. Electrical Interface 3.1 Pin Assignment and Pin Type PC Card Memory Mode Pin Num Signal Name 1 GND 2 D03 3 Pin Type PC Card I/O Mode In, Out Type Pin Num Signal Name Ground 1 GND I/O I1Z, OZ3 2 D03 D04 I/O I1Z, OZ3 3 4 D05 I/O I1Z, OZ3 5 D06 I/O 6 D07 7 -CE1 Pin Type True IDE Mode In, Out Type Pin Num Signal Name Ground 1 GND I/O I1Z, OZ3 2 D03 I/O I1Z, OZ3 D04 I/O I1Z, OZ3 3 D04 I/O I1Z, OZ3 4 D05 I/O I1Z, OZ3 4 D05 I/O I1Z, OZ3 I1Z, OZ3 5 D06 I/O I1Z, OZ3 5 D06 I/O I1Z, OZ3 I/O I1Z, OZ3 6 D07 I/O I1Z, OZ3 6 D07 I/O I1Z, OZ3 I I3U 7 -CE1 I I3U 7 -CS0 I I3Z 2 I I1Z 8 A10 I I1Z 8 A10 I I1Z 8 A10 9 -OE I I3U 9 -OE I I3U 9 -ATA SEL 10 11 A09 I A08 I 12 A07 13 VCC 14 15 16 I A06 I A05 I A04 4 I I1Z I1Z 10 11 A09 I A08 I I1Z 12 A07 Power 13 VCC I1Z I1Z I1Z 14 15 16 I A06 I A05 I A04 I I1Z I1Z 10 11 Pin Type In, Out Type Ground I I3U A09 2 I I1Z A08 2 I I1Z 2 I I1Z I1Z 12 A07 Power 13 VCC 14 A06 2 I I1Z A05 2 I I1Z A04 2 I I1Z 2 I I1Z I1Z I1Z I1Z 15 16 Power 17 A03 I I1Z 17 A03 I I1Z 17 A03 18 A02 I I1Z 18 A02 I I1Z 18 A02 I I1Z 19 A01 I I1Z 19 A01 I I1Z 19 A01 I I1Z 20 A00 I I1Z 20 A00 I I1Z 20 A00 I I1Z 21 D00 I/O I1Z, OZ3 21 D00 I/O I1Z, OZ3 21 D00 I/O I1Z, OZ3 22 D01 I/O I1Z, OZ3 22 D01 I/O I1Z, OZ3 22 D01 I/O I1Z, OZ3 23 D02 I/O I1Z, OZ3 23 D02 I/O I1Z, OZ3 23 D02 I/O I1Z, OZ3 24 WP O OT3 24 -IOIS16 O OT3 24 -IOCS16 O ON3 25 -CD2 O Ground 25 -CD2 O Ground 25 -CD2 O Ground 26 -CD1 O Ground 26 -CD1 O Ground 26 -CD1 O Ground 27 1 27 1 27 D11 1 I/O I1Z, OZ3 D12 1 I/O I1Z, OZ3 D13 1 I/O I1Z, OZ3 D14 1 I/O I1Z, OZ3 D15 1 I/O I1Z, OZ3 I I3Z D11 28 D121 29 D13 1 D14 1 D15 1 30 31 32 -CE2 1 I/O I/O I/O I/O I/O I I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U Transcend Information Inc. 28 29 30 31 32 D11 I/O 1 D12 I/O 1 D13 I/O 1 D14 I/O 1 D15 -CE2 I/O 1 I 5 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U 28 29 30 31 32 -CS1 1 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card PC Card Memory Mode PC Card I/O Mode True IDE Mode 4 Pin Num Signal Name Pin Type In, Out Type Pin Num Signal Name Pin Type In, Out Type Pin Num Signal Name Pin Type In, Out Type 33 -VS1 O Ground 33 -VS1 O Ground 33 -VS1 O Ground 34 -IORD I I3U 34 -IORD I I3U 34 -IORD I I3Z 35 -IOWR I I3U 35 -IOWR I I3U 35 -IOWR I I3Z 36 -WE I I3U 36 -WE I I3U 36 -WE I I3U 37 READY O OT1 37 -IREQ O OT1 37 INTRQ O OZ1 38 VCC Power 38 VCC Power 38 VCC I I2Z 39 -CSEL I I2U 39 -CSEL 5 I I2Z 39 -CSEL 5 3 Power 40 -VS2 O OPEN 40 -VS2 O OPEN 40 -VS2 O OPEN 41 RESET I I2Z 41 RESET I I2Z 41 -RESET I I2Z 42 -WAIT O OT1 42 -WAIT O OT1 42 IORDY O ON1 43 -INPACK O OT1 43 -INPACK O OT1 43 DMARQ O OZ1 I I3U 6 44 -REG I I3U 44 -REG I I3U 44 -DMACK 45 BVD2 O OT1 45 -SPKR O OT1 45 -DASP I/O I1U, ON1 46 BVD1 O OT1 46 -STSCHG O OT1 46 -PDIAG 47 D08 1 I/O 48 D09 1 I/O 49 D10 1 I/O 50 GND I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground 47 D08 1 48 D09 1 I/O 49 D10 1 I/O 50 GND I/O I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground I/O I1U, ON1 I/O I1Z, OZ3 47 D08 1 48 D09 1 I/O I1Z, OZ3 49 D10 1 I/O I1Z, OZ3 50 GND Ground Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. Devices should allow for 3-state signals not to consume current. 2) The signal should be grounded by the host. 3) The signal should be tied to VCC by the host. 4) The mode is required for CompactFlash Storage Cards. 5) The -CSEL signal is ignored by the card in PC Card modes. However, because it is not pulled upon the card in these modes, it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC Card A25 or grounded by the host. 6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. For proper operation in older hosts: while DMA operations are not active, the card shall ignore this signal,including a floating condition Transcend Information Inc. 6 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.2 Signal Description Signal Name Dir. A10 – A00 (PC Card Memory Mode) I Pin Description 8,10,11,12, These address lines along with the -REG signal are used to select the following: 14,15,16,17, The I/O port address registers within the CompactFlash Storage Card , the 18,19,20 memory mapped port address registers within the CompactFlash Storage Card, a byte in the card's information structure and its configuration control and status registers. A10 – A00 (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal. I A02 - A00 (True IDE Mode) BVD1 (PC Card Memory Mode) 18,19,20 I/O 46 In True IDE Mode, only A[02:00] are used to select the one of eight registers in the Task File, the remaining address lines should be grounded by the host. This signal is asserted high, as BVD1 is not supported. -STSCHG (PC Card I/O Mode) Status Changed This signal is asserted low to alert the host to changes in the READY and Write Protect states, while the I/O interface is configured. Its use is controlled by the Card Config and Status Register. -PDIAG (True IDE Mode) In the True IDE Mode, this input / output is the Pass Diagnostic signal in the Master / Slave handshake protocol. BVD2 (PC Card Memory Mode) I/O 45 This signal is asserted high, as BVD2 is not supported. -SPKR (PC Card I/O Mode) This line is the Binary Audio output from the card. If the Card does not support the Binary Audio function, this line should be held negated. -DASP (True IDE Mode) In the True IDE Mode, this input/output is the Disk Active/Slave Present signal in the Master/Slave handshake protocol. Transcend Information Inc. 7 V1.1 TTS S3322M M~~11G GC CFF8800 -CD1, -CD2 (PC Card Memory Mode) 80X CompactFlash Card O 26,25 These Card Detect pins are connected to ground on the CompactFlash Storage Card. They are used by the host to determine that the CompactFlash Storage Card is fully inserted into its socket. -CD1, -CD2 (PC Card I/O Mode) This signal is the same for all modes. -CD1, -CD2 (True IDE Mode) This signal is the same for all modes. Signal Name Dir. Pin -CE1, -CE2 (PC Card Memory Mode) Card Enable I 7,32 Description These input signals are used both to select the card and to indicate to the card whether a byte or a word operation is being performed. -CE2 always accesses the odd byte of the word.-CE1 accesses the even byte or the Odd byte of the word depending on A0 and -CE2. A multiplexing scheme based on A0,-CE1, -CE2 allows 8 bit hosts to access all data on D0-D7. See Table 27, Table 29, Table 31, Table 35, Table 36 and Table 37. This signal is the same as the PC Card Memory Mode signal. -CE1, -CE2 (PC Card I/O Mode) Card Enable In the True IDE Mode, -CS0 is the address range select for the task file registers while -CS1 is used to select the Alternate Status Register and the Device Control Register. -CS0, -CS1 (True IDE Mode) While –DMACK is asserted, -CS0 and –CS1 shall be held negated and the width of the transfers shall be 16 bits. -CSEL (PC Card Memory Mode) I 39 This signal is not used for this mode, but should be connected by the host to PC Card A25 or grounded by the host. -CSEL (PC Card I/O Mode) This signal is not used for this mode, but should be connected by the host to PC Card A25 or grounded by the host. -CSEL (True IDE Mode) This internally pulled up signal is used to configure this device as a Master or a Slave when configured in the True IDE Mode. When this pin is grounded, this device is configured as a Master. When the pin is open, this device is configured as a Slave. Transcend Information Inc. 8 V1.1 TTS S3322M M~~11G GC CFF8800 D15 - D00 (PC Card Memory Mode) 80X CompactFlash Card I/O 31,30,29,28, These lines carry the Data, Commands and Status information between the host 27,49,48,47, and the controller. D00 is the LSB of the Even Byte of the Word. D08 is the LSB 6,5,4,3,2, of the Odd Byte of the Word. 23, 22, 21 D15 - D00 (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal. D15 - D00 (True IDE Mode) In True IDE Mode, all Task File operations occur in byte mode on the low order bus D[7:0] while all data transfers are 16 bit using D[15:0]. GND (PC Card Memory Mode) -- 1,50 Ground. GND (PC Card I/O Mode) This signal is the same for all modes. GND (True IDE Mode) This signal is the same for all modes. Signal Name Dir. Pin -INPACK (PC Card Memory Mode) O 43 Description This signal is not used in this mode. -INPACK (PC Card I/O Mode) Input Acknowledge The Input Acknowledge signal is asserted by the CompactFlash Storage Card when the card is selected and responding to an I/O read cycle at the address that is on the address bus. This signal is used by the host to control the enable of any input data buffers between the CompactFlash Storage Card and the CPU. DMARQ (True IDE Mode) This signal is a DMA Request that is used for DMA data transfers between host and device. It shall be asserted by the device when it is ready to transfer data to or from the host. For Multiword DMA transfers, the direction of data transfer is controlled by -IORD and -IOWR. This signal is used in a handshake manner with -DMACK, i.e., the device shall wait until the host asserts -DMACK before negating DMARQ, and reasserting DMARQ if there is more data to transfer. DMARQ shall not be driven when the device is not selected. While a DMA operation is in progress, -CS0 and –CS1 shall be held negated and the width of the transfers shall be 16 bits. If there is no hardware support for DMA mode in the host, this output signal is not used and should not be connected at the host. In this case, the BIOS must report that DMA mode is not supported by the host so that device drivers will not attempt DMA mode. A host that does not support DMA mode and implements both PCMCIA and True-IDE modes of operation need not alter the PCMCIA mode connections while in True-IDE mode as long as this does not prevent proper operation in any mode. Transcend Information Inc. 9 V1.1 TTS S3322M M~~11G GC CFF8800 -IORD (PC Card Memory Mode) 80X CompactFlash Card I 34 This is an I/O Read strobe generated by the host. This signal gates I/O data onto the bus from the CompactFlash Storage Card when the card is configured to use the I/O interface. -IORD (PC Card I/O Mode) In True IDE Mode, this signal has the same function as in PC Card I/O Mode. -IORD (True IDE Mode ) -IOWR (PC Card Memory Mode) This signal is not used in this mode. I 35 -IOWR (PC Card I/O Mode) This signal is not used in this mode. The I/O Write strobe pulse is used to clock I/O data on the Card Data bus into the CompactFlash Storage Card controller registers when the CompactFlash Storage Card is configured to use the I/O interface. The clocking shall occur on the negative to positive edge of the signal (trailing edge). -IOWR (True IDE Mode) In True IDE Mode, this signal has the same function as in PC Card I/O Mode. Signal Name Dir. Pin -OE (PC Card Memory Mode) I 9 Description This is an Output Enable strobe generated by the host interface. It is used to read data from the CompactFlash Storage Card in Memory Mode and to read the CIS and configuration registers. -OE (PC Card I/O Mode) In PC Card I/O Mode, this signal is used to read the CIS and configuration registers. -ATA SEL (True IDE Mode) To enable True IDE Mode this input should be grounded by the host. READY (PC Card Memory Mode) O 37 In Memory Mode, this signal is set high when the CompactFlash Storage Card is ready to accept a new data transfer operation and is held low when the card is busy. At power up and at Reset, the READY signal is held low (busy) until the CompactFlash Storage Card has completed its power up or reset function. No access of any type should be made to the CompactFlash Storage Card during this time. Note, however, that when a card is powered up and used with RESET continuously disconnected or asserted, the Reset function of the RESET pin is disabled. Consequently, the continuous assertion of RESET from the application of power shall not cause the READY signal to remain continuously in the busy state. -IREQ (PC Card I/O Mode) I/O Operation – After the CompactFlash Storage Card Card has been configured for I/O operation, this signal is used as -Interrupt Request. This line is strobed low to generate a pulse mode interrupt or held low for a level mode interrupt. INTRQ (True IDE Mode) In True IDE Mode signal is the active high Interrupt Request to the host. Transcend Information Inc. 10 V1.1 TTS S3322M M~~11G GC CFF8800 -REG (PC Card Memory Mode) Attribute Memory Select 80X CompactFlash Card I 44 This signal is used during Memory Cycles to distinguish between Common Memory and Register (Attribute) Memory accesses. High for Common Memory, Low for Attribute Memory. -REG (PC Card I/O Mode) The signal shall also be active (low) during I/O Cycles when the I/O address is on the Bus. -DMACK (True IDE Mode) This is a DMA Acknowledge signal that is asserted by the host in response to DMARQ to initiate DMA transfers. While DMA operations are not active, the card shall ignore the -DMACK signal, including a floating condition. If DMA operation is not supported by a True IDE Mode only host, this signal should be driven high or connected to VCC by the host. A host that does not support DMA mode and implements both PCMCIA and True-IDE modes of operation need not alter the PCMCIA mode connections while in True-IDE mode as long as this does not prevent proper operation all modes. Signal Name Dir. Pin RESET (PC Card Memory Mode) I 41 Description The CompactFlash Storage Card is Reset when the RESET pin is high with the following important exception: The host may leave the RESET pin open or keep it continually high from the application of power without causing a continuous Reset of the card. Under either of these conditions, the card shall emerge from power-up having completed an initial Reset. The CompactFlash Storage Card is also Reset when the Soft Reset bit in the Card Configuration Option Register is set. RESET (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal. -RESET (True IDE Mode) In the True IDE Mode, this input pin is the active low hardware reset from the host. VCC (PC Card Memory Mode) -- 13,38 +5 V, +3.3 V power. VCC (PC Card I/O Mode) This signal is the same for all modes. VCC (True IDE Mode) This signal is the same for all modes. Transcend Information Inc. 11 V1.1 TTS S3322M M~~11G GC CFF8800 -VS1 -VS2 (PC Card Memory Mode) 80X CompactFlash Card O 33 40 Voltage Sense Signals. -VS1 is grounded on the Card and sensed by the Host so that the CompactFlash Storage Card CIS can be read at 3.3 volts and -VS2 is reserved by PCMCIA for a secondary voltage and is not connected on the Card. -VS1 -VS2 (PC Card I/O Mode) This signal is the same for all modes. -VS1 -VS2 (True IDE Mode) This signal is the same for all modes. -WAIT (PC Card Memory Mode) O 42 The -WAIT signal is driven low by the CompactFlash Storage Card to signal the host to delay completion of a memory or I/O cycle that is in progress. -WAIT (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal. IORDY (True IDE Mode) In True IDE Mode, except in Ultra DMA modes, this output signal may be used as IORDY. Signal Name Dir. Pin -WE (PC Card Memory Mode) I 36 Description This is a signal driven by the host and used for strobing memory write data to the registers of the CompactFlash Storage Card when the card is configured in the memory interface mode. It is also used for writing the configuration registers. -WE (PC Card I/O Mode) In PC Card I/O Mode, this signal is used for writing the configuration registers. -WE (True IDE Mode) WP (PC Card Memory Mode) Write Protect In True IDE Mode, this input signal is not used and should be connected to VCC by the host. Memory Mode – The CompactFlash Storage Card does not have a write protect switch. This signal is held low after the completion of the reset initialization sequence. O 24 -IOIS16 (PC Card I/O Mode) I/O Operation – When the CompactFlash Storage Card is configured for I/O Operation Pin 24 is used for the -I/O Selected is 16 Bit Port (-IOIS16) function. A Low signal indicates that a 16 bit or odd byte only operation can be performed at the addressed port. -IOCS16 (True IDE Mode) In True IDE Mode this output signal is asserted low when this device is expecting a word data transfer cycle. Transcend Information Inc. 12 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.3 Electrical Specification The following tables indicate all D.C. Characteristics for the CompactFlash Storage Card. Unless otherwise stated, conditions are: Vcc = 5V ±10% Vcc = 3.3V ± 5% Absolute Maximum Conditions Input Power 3.3.1 Input Leakage Current Transcend Information Inc. 13 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.3.2 Input Characteristics 3.3.2.1 CompactFlash interface I/O at 5.0V Parameter Symbol Min. Max. 5.5 Supply Voltage VCC 4.5 High level output voltage VOH VCC-0.8 Low level output voltage VOL High level input voltage VIH Low level input voltage VIL Pull up resistance 2 Pull down resistance Transcend Information Inc. Unit V V 0.8 V 4.0 V Non-schmitt trigger 2.6 V Schmitt trigger 0.8 V Non-schmitt trigger 1.79 V Schmitt trigger RPU 52.54 86.56 kOhm RPD 63 244 kOhm 14 Remark 1 1 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.3.2.2 CompactFlash interface I/O at 3.3V Parameter Symbol Min. Max. Unit 3.465 V Supply Voltage VCC 3.135 High level output voltage VOH VCC-0.8 Low level output voltage VOL High level input voltage VIH Low level input voltage VIL Pull up resistance 2 Pull down resistance Remark V 0.8 V 2.4 V Non-schmitt trigger 1.67 V Schmitt trigger 0.6 V Non-schmitt trigger 1.07 V Schmitt trigger RPU 81.39 154.85 kOhm RPD 42 172 kOhm 1 1 3.3.2.3 The I/O pins other than CompactFlash interface Parameter Symbol Min. Max. Unit Supply Voltage VCC 3.135 3.465 V High level output voltage VOH 2.4 Low level output voltage VOL High level input voltage V 0.4 2.0 VIH Remark V V 1.4 Non-schmitt trigger V Schmitt trigger 0.8 V Non-schmitt trigger 1.2 V Schmitt trigger Low level input voltage VIL Pull up resistance RPU 40 kOhm Pull down resistance RPD 40 kOhm 1. Include CE1,CE2 ,HREG ,HOE ,HIOE ,HWE ,HIOW pins. 2. Include CE1,CE2 ,HREG ,HOE , HIOE ,HWE ,HIOW ,CSEL ,PDIAG ,DASP pins. Transcend Information Inc. 15 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.3.3 Output Drive Type 3.3.4 Output Drive Characteristics Transcend Information Inc. 16 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.4 Signal Interface Electrical specifications shall be maintained to ensure data reliability. Item Control Signal Status Signal Card10 Host10 Signal -CE1 -CE2 -REG -IORD -IOWR -OE -WE Pull-up to VCC 500 KΩ ≧ R ≧ 50 KΩ . 1,2 RESET Pull-up to VCC 500 KΩ ≧ R ≧ 50 KΩ . 1,2,9, Pull-up to VCC 500 KΩ ≧ R≧ 50 KΩ and shall be sufficient to keep inputs inactive 1 when the pins are not connected at the host. READY -WAIT WP Pull-up to VCC R ≧ 10 KΩ . 3 In PCMCIA PC Card modes Pull-up to VCC 4 R ≧ 10 KΩ . In True IDE mode, if DMA operation is supported by the host, Pull-down to Gnd R 5 ≧ 5.6 KΩ . -INPACK PC Card / True IDE hosts switch the pull-up to pull down in True IDE mode if DMA operation is supported. The PC Card mode Pull-up may be left active during True IDE mode if True IDE DMA operation is not supported. Address Data Bus Card Detect Voltage Sense Battery/Detect A[10:00] -CSEL D[15:00] -CD[2:1] Connected to GND in the card -VS1 -VS2 BVD[2:1] 1. Pull-up to Vcc 10 KΩ Pull-up R ≧ 50 KΩ . ≦ R ≦ 100KΩ . 3.6 Notes: 1) Control Signals: each card shall present a load to the socket no larger than 50 pF 10 at a DC current of 700 μ A low state and 150 μ A high state, including pull-resistor. The socket shall be able to drive at least the following load 10 while meeting all AC timing requirements: (the number of sockets wired in parallel) multiplied by (50 pF with DC current 700 μ A low state and 150 μ A high state per socket). 2) Resistor is optional. 3) Status Signals: the socket shall present a load to the card no larger than 50 pF 10 at a DC current of 400 μ A low state and 100 μ A high state, including pull-up resistor. The card shall be able to drive at least the following load 10 while meeting all AC timing requirements: 50 pF at a DC current of 400 μ A low state and 100 μ A high state. 4) Status Signals: the socket shall present a load to the card no larger than 50 pF 10 at a DC current of 400 μ A low state and 100 μ A high state, including pull-up resistor. The card shall be able to drive at least the following load 10 while Transcend Information Inc. 17 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card meeting all AC timing requirements: 50 pF at a DC current of 400 μ A low state and 100 μ A high state. 5) Status Signals: the socket shall present a load to the card no larger than 50 pF 10 at a DC current of 400 μ A low state and 100 μ A high state, including pull-up resistor. The card shall be able to drive at least the following load 10 while meeting all AC timing requirements: 50 pF at a DC current of 400 μ A low state and 1100 μ A high state. 6) BVD2 was not defined in the JEIDA 3.0 release. Systems fully supporting JEIDA release 3 SRAM cards shall pull-up pin 45 (BVD2) to avoid sensing their batteries as “Low.” 7) Address Signals: each card shall present a load of no more than 100pF 10 at a DC current of 450μ A low state and 150μ A high state. The host shall be able to drive at least the following load 10 while meeting all AC timing requirements: (the number of sockets wired in parallel) multiplied by (100pF with DC current 450μ A low state and 150μ A high state per socket). 8) Data Signals: the host and each card shall present a load no larger than 50pF 10 at a DC current of 450μ A and 150 μ A high state. The host and each card shall be able to drive at least the following load 10 while meeting all AC timing requirements: 100pF with DC current 1.6mA low state and 300μ A high state. This permits the host to wire two sockets in parallel without derating the card access speeds. 9) Reset Signal: This signal is pulled up to prevent the input from floating when a CFA to PCMCIA adapter is used in a PCMCIA revision 1 host. However, to minimize DC current drain through the pull-up resistor in normal operation the pull-up should be turned off once the Reset signal has been actively driven low by the host. Consequently, the input is specified as an I2Z because the resistor is not necessarily detectable in the input current leakage test. Transcend Information Inc. 18 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.5 Attribute Memory Read Timing Figure: Attribute Memory Read Timing Diagram Transcend Information Inc. 19 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.6 Configuration Register (Attribute Memory) Write Timing Figure: Configuration Register (Attribute Memory) Write Timing Diagram Transcend Information Inc. 20 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.7 Common Memory Read Timing Specification Cycle Time Mode: 250 ns Max ns. Min ns. Max ns. 100 ns Min ns. Max ns. 80 ns Min ns. Ma x ns. Symbol IEEE Symbol Output Enable Access Time ta(OE) tGLQV 125 60 50 45 Output Disable Time from OE tdis(OE) tGHQZ 100 60 50 45 Address Setup Time tsu(A) tAVGL 30 15 10 10 Address Hold Time th(A) tGHAX 20 15 15 10 CE Setup before OE tsu(CE) tELGL 0 0 0 0 CE Hold following OE th(CE) tGHEH 20 15 15 10 Wait Delay Falling from OE tv(WT-OE ) tGLWTV 35 35 35 na 1 Data Setup for Wait Release tv(WT) tQVWTH 0 0 0 na 1 Wait Width Time2 tw(WT) tWTLWTH 350 350 350 na 1 Item Min ns. 120 ns Notes:1) –WAIT is not supported in this mode. 2) The maximum load on -WAIT is 1 LSTTL with 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Dout signifies data provided by the CompactFlash Storage Card to the system. The -WAIT signal may be ignored if the -OE cycle to cycle time is greater than the Wait Width time. The Max Wait Width time can be determined from the Card Information Structure. The Wait Width time meets the PCMCIA PC Card specification of 12µs but is intentionally less in this specification. Transcend Information Inc. 21 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.8 Common Memory Write Timing Specification Cycle Time Mode: 250 ns 120 ns Max ns. Min ns. Max ns. 100 ns Min ns. Max ns. 80 ns Min ns. Item Symbol IEEE Symbol Min ns. Data Setup before WE tsu (D-WEH) tDVWH 80 50 40 30 Data Hold following WE th(D) tWMDX 30 15 10 10 WE Pulse Width tw(WE) tWLWH 150 70 60 55 Address Setup Time tsu(A) tAVWL 30 15 10 10 CE Setup before WE tsu(CE) tELWL 0 0 0 0 Write Recovery Time trec(WE) tWMAX 30 15 15 15 Address Hold Time th(A) tGHAX 20 15 15 15 CE Hold following WE th(CE) tGHEH 20 15 15 10 Wait Delay Falling from WE tv (WT-WE) tWLWTV WE High from Wait Release tv(WT) tWTHWH Wait Width Time2 tw (WT) tWTLWTH 35 0 35 0 350 35 0 350 Ma x ns. na1 na1 350 na1 Notes: 1) –WAIT is not supported in this mode. 2) The maximum load on -WAIT is 1 LSTTL with 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Din signifies data provided by the system to the CompactFlash Storage Card. The -WAIT signal may be ignored if the -WE cycle to cycle time is greater than the Wait Width time. The Max Wait Width time can be determined from the Card Information Structure. The Wait Width time meets the PCMCIA PC Card specification of 12µs but is intentionally less in this specification. Transcend Information Inc. 22 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.9 I/O Input (Read) Timing Specification Cycle Time Mode: Item Symbol IEEE Symbol 250 ns Min ns. 120 ns Max ns. Min ns. Max ns. Min ns. Max ns. Min ns. td(IORD) tlGLQV Data Hold following IORD th(IORD) tlGHQX 0 5 5 5 IORD Width Time tw(IORD) tlGLIGH 165 70 65 55 Address Setup before IORD tsuA(IORD) tAVIGL 70 25 25 15 Address Hold following IORD thA(IORD) tlGHAX 20 10 10 10 CE Setup before IORD tsuCE(IORD) tELIGL 5 5 5 5 CE Hold following IORD thCE(IORD) tlGHEH 20 10 10 10 REG Setup before IORD tsuREG (IORD) tRGLIGL 5 5 5 5 REG Hold following IORD thREG (IORD) tlGHRGH 0 0 0 0 INPACK Delay Falling from IORD 3 tdfINPACK (IORD) tlGLIAL 0 3 tdrINPACK (IORD) tlGHIAH 3 tdfIOIS16 (ADR) 3 IOIS16 Delay Falling from Address IOIS16 Delay Rising from Address Wait Delay Falling from IORD Data Delay from Wait Rising 3 3 Wait Width Time3 Transcend Information Inc. 50 80 ns Data Delay after IORD INPACK Delay Rising from IORD 100 100 ns 50 na 1 45 na tAVISL 35 tdrIOIS16 (ADR) tAVISH tdWT(IORD) 45 na 1 1 na na 1 35 na tlGLWTL td(WT) tWTHQV tw(WT) tWTLWTH 23 Ma x ns. na 1 1 na 1 na 1 na 1 1 na 1 na 1 35 35 35 na 2 0 0 0 na 2 350 350 350 na 2 45 0 0 0 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.10 I/O Output (Write) Timing Specification Cycle Time Mode: Item Symbol IEEE Symbol 255 ns Min ns. Max ns. 120 ns Min ns. Max ns. 100 ns Min ns. Max ns. 80 ns Min ns. Data Setup before IOWR tsu(IOWR) tDVIWH 60 20 20 15 Data Hold following IOWR th(IOWR) tlWHDX 30 10 5 5 IOWR Width Time tw(IOWR) tlWLIWH 165 70 65 55 Address Setup before IOWR tsuA(IOWR) tAVIWL 70 25 25 15 Address Hold following IOWR thA(IOWR) tlWHAX 20 20 10 10 CE Setup before IOWR tsuCE (IOWR) tELIWL 5 5 5 5 CE Hold following IOWR thCE (IOWR) tlWHEH 20 20 10 10 REG Setup before IOWR tsuREG (IOWR) tRGLIWL 5 5 5 5 thREG (IOWR) tlWHRGH 0 0 REG Hold following IOWR IOIS16 Delay Falling from Address IOIS16 Delay Rising from Address Wait Delay Falling from IOWR IOWR high from Wait high Wait Width Time 3 3 3 3 3 Transcend Information Inc. 0 tdfIOIS16 (ADR) tAVISL 35 na 1 tdrIOIS16 (ADR) tAVISH 35 na 1 tdWT(IOWR) tlWLWTL 35 35 tdrIOWR (WT) tWTJIWH tw(WT) tWTLWT H 24 0 0 350 0 na 1 na 1 35 na 1 na 1 na 2 na 2 2 0 350 Ma x ns. na 350 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.11 True IDE PIO Mode Read/Write Timing Specification Mode Item 0 1 Note 2 3 4 5 6 t0 Cycle time (min) 600 383 240 180 120 100 80 t1 Address Valid to -IORD/-IOWR setup (min) 70 50 30 30 25 15 10 t2 -IORD/-IOWR (min) 165 125 100 80 70 65 55 1 t2 -IORD/-IOWR (min) Register (8 bit) 290 290 290 80 70 65 55 1 t2i -IORD/-IOWR recovery time (min) - - - 70 25 25 20 1 t3 -IOWR data setup (min) 60 45 30 30 20 20 15 t4 -IOWR data hold (min) 30 20 15 10 10 5 5 t5 -IORD data setup (min) 50 35 20 20 20 15 10 t6 -IORD data hold (min) 5 5 5 5 5 5 5 -IORD data tristate (max) 30 30 30 30 30 20 20 2 90 50 40 n/a n/a n/a n/a 4 60 45 30 n/a n/a n/a n/a 4 T6Z t7 t8 Address valid to -IOCS16 assertion (max) Address valid to -IOCS16 released (max) t9 -IORD/-IOWR to address valid hold 20 15 10 10 10 10 10 tRD Read Data Valid to IORDY active (min), if IORDY initially low after tA 0 0 0 0 0 0 0 tA IORDY Setup time 35 35 35 35 35 na 5 na 5 tB IORDY Pulse Width (max) 125 0 1250 1250 1250 1250 na 5 na 5 tC IORDY assertion to release (max) 5 5 5 5 5 na 5 na 5 1 3 Notes: All timings are in nanoseconds. The maximum load on -IOCS16 is 1 LSTTL with a 50 pF (40pF below 120nsec Cycle Time) total load. All times are in nanoseconds. Minimum time from -IORDY high to -IORD high is 0 nsec, but minimum -IORD width shall still be met. 1) t0 is the minimum total cycle time, t2 is the minimum command active time, and t2i is the minimum command recovery time or command inactive time. The actual cycle time equals the sum of the actual command active time and the actual command inactive time. The three timing requirements of t0, t2, and t2i shall be met. The minimum total cycle time requirement is greater than the sum of t2 and t2i. This means a host implementation can lengthen either or both t2 or t2i to ensure that t0 is equal to or greater than the value reported in the device’s identify device data. A CompactFlash Storage Card implementation shall support any legal host implementation. 2) This parameter specifies the time from the negation edge of -IORD to the time that the data bus is no longer driven by the CompactFlash Storage Card (tri-state). 3) The delay from the activation of -IORD or -IOWR until the state of IORDY is first sampled. If IORDY is inactive then the host shall wait until IORDY is active before the PIO cycle can be completed. If the CompactFlash Storage Card is not driving IORDY negated at tA after the activation of -IORD or -IOWR, then t5 shall be met and tRD is not applicable. If the CompactFlash Storage Card is driving IORDY negated at the time tA after the activation of -IORD or -IOWR, then tRD shall be met and t5 is not applicable. 4) t7 and t8 apply only to modes 0, 1 and 2. For other modes, this signal is not valid. 5) IORDY is not supported in this mode. Transcend Information Inc. 25 V1.1 TTS S3322M M~~11G GC CFF8800 Transcend Information Inc. 80X CompactFlash Card 26 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 3.12 True IDE Multiword DMA Mode Read/Write Timing Specification The timing diagram for True IDE DMA mode of operation in this section is drawn using the conventions in the ATA-4 specification. Signals are shown with their asserted state as high regardless of whether the signal is actually negative or positive true. Consequently, the -IORD, the -IOWR and the -IOCS16 signals are shown in the diagram inverted from their electrical states on the bus. Item Mode 0 (ns) Mode 1 (ns) Mode 2 (ns) Mode 3 (ns) Mode 4 (ns) Note tO Cycle time (min) 480 150 120 100 80 1 tD -IORD / -IOWR asserted width (min) 215 80 70 65 55 1 tE -IORD data access (max) 150 60 50 50 45 tF -IORD data hold (min) 5 5 5 5 5 tG -IORD/-IOWR data setup (min) 100 30 20 15 10 tH -IOWR data hold (min) 20 15 10 5 5 tI DMACK to –IORD/-IOWR setup (min) 0 0 0 0 0 tJ -IORD / -IOWR to -DMACK hold (min) 20 5 5 5 5 tKR -IORD negated width (min) 50 50 25 25 20 1 tKW -IOWR negated width (min) 215 50 25 25 20 1 tLR -IORD to DMARQ delay (max) 120 40 35 35 35 tLW -IOWR to DMARQ delay (max) 40 40 35 35 35 tM CS(1:0) valid to –IORD / -IOWR 50 30 25 10 5 tN CS(1:0) hold 15 10 10 10 10 tZ -DMACK 20 25 25 25 25 Transcend Information Inc. 27 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 4. Card Configuration The CompactFlash Storage Cards is identified by appropriate information in the Card Information Structure (CIS). The following configuration registers are used to coordinate the I/O spaces and the Interrupt level of cards that are located in the system. In addition, these registers provide a method for accessing status information about the CompactFlash Storage Card that may be used to arbitrate between multiple interrupt sources on the same interrupt level or to replace status information that appears on dedicated pins in memory cards that have alternate use in I/O cards. 4.1 Multiple Function CompactFlash Storage Cards Table: CompactFlash Storage Card Registers and Memory Space Decoding -CE2 -CE1 -REG -OE -WE A10 A9 A8-A4 A3 A2 A1 A0 SELECTED SPACE 1 1 X X X X X XX X X X X Standby and UDMA transfer X 0 0 0 1 0 1 XX X X X 0 Configuration Registers Read 1 0 1 0 1 X X XX X X X X Common Memory Read (8 Bit D7-D0) 0 1 1 0 1 X X XX X X X X Common Memory Read (8 Bit D15-D8) 0 0 1 0 1 X X XX X X X 0 Common Memory Read (16 Bit D15-D0) X 0 0 1 0 0 1 XX X X X 0 Configuration Registers Write 1 0 1 1 0 X X XX X X X X Common Memory Write (8 Bit D7-D0) 0 1 1 1 0 X X XX X X X X Common Memory Write (8 Bit D15-D8) 0 0 1 1 0 X X XX X X X 0 Common Memory Write (16 Bit D15-D0) X 0 0 0 1 0 0 XX X X X 0 Card Information Structure Read 1 0 0 1 0 0 0 XX X X X 0 Invalid Access (CIS Write) 1 0 0 0 1 X X XX X X X 1 Invalid Access (Odd Attribute Read) 1 0 0 1 0 X X XX X X X 1 Invalid Access (Odd Attribute Write) 0 1 0 0 1 X X XX X X X X Invalid Access (Odd Attribute Read) 0 1 0 1 0 X X XX X X X X Invalid Access (Odd Attribute Write) Table: CompactFlash Storage Card Configuration Registers Decoding -CE2 -CE1 -REG -OE -WE A10 A9 A8-A4 A3 A2 A1 A0 SELECTED REGISTER X 0 0 0 1 0 1 00 0 0 0 0 Configuration Option Reg Read X 0 0 1 0 0 1 00 0 0 0 0 Configuration Option Reg Write X 0 0 0 1 0 1 00 0 0 1 0 Card Status Register Read X 0 0 1 0 0 1 00 0 0 1 0 Card Status Register Write X 0 0 0 1 0 1 00 0 1 0 0 Pin Replacement Register Read X 0 0 1 0 0 1 00 0 1 0 0 Pin Replacement Register Write X 0 0 0 1 0 1 00 0 1 1 0 Socket and Copy Register Read X 0 0 1 0 0 1 00 0 1 1 0 Socket and Copy Register Write Note: For CompactFlash Storage Cards, the location of the card configuration registers should always be read from the CIS since these locations may vary in future products. Transcend Information Inc. 28 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 4.2 Attribute Memory Function Attribute memory is a space where CompactFlash Storage Card identification and configuration information are stored, and is limited to 8 bit wide accesses only at even addresses. The card configuration registers are also located here. For CompactFlash Storage Cards, the base address of the Card configuration registers is 200h. Table: Attribute Memory Function Function Mode DMA CMD -REG -CE2 -CE1 A10 A9 A0 -OE -WE D15-D8 D7-D0 Standby Mode Don’t Care H H H X X X X X High Z High Z Standby Mode No X H H X X X X X High Z High Z UDMA Operation (see section 4.3.18: Ultra DMA Mode Read/Write Timing Specification) Yes L1 H H X X X H H Odd Byte Even Byte Read Byte Access CIS ROM (8 bits) No L H L2 L L L L2 H High Z Even Byte Write Byte Access CIS (8 bits) (Invalid) No L H L2 L L L H L2 Don’t Care Even Byte Read Byte Access Configuration CompactFlash Storage (8 bits) No L H L L H L L H High Z Even Byte Write Byte Access Configuration CompactFlash Storage (8 bits) No L H L L H L H L Don’t Care Even Byte Read Word Access CIS (16 bits) No L L2 L2 L L X L2 H Not Valid Even Byte Write Word Access CIS (16 bits) (Invalid) No L L2 L2 L L X H L2 Don’t Care Even Byte Read Word Access Configuration CompactFlash Storage (16 bits) No L L2 L2 L H X L2 H Not Valid Even Byte Write Word Access Configuration CompactFlash Storage (16 bits) No L L2 L2 L H X H L2 Don’t Care Even Byte Note: The -CE signal or both the -OE signal and the -WE signal shall be de-asserted between consecutive cycle operations. Transcend Information Inc. 29 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 4.3 Configuration Option Register(Base + 00h in Attribute Memory) The Configuration Option Register is used to configure the cards interface, address decoding and interrupt and to issue a soft reset to the CompactFlash Storage Card. SRESET - Soft Reset: setting this bit to one (1), waiting the minimum reset width time and returning to zero (0) places the CompactFlash Storage Card in the Reset state. Setting this bit to one (1) is equivalent to assertion of the +RESET signal except that the SRESET bit is not cleared. Returning this bit to zero (0) leaves the CompactFlash Storage Card in the same un-configured, Reset state as following power-up and hardware reset. This bit is set to zero (0) by power-up and hardware reset. For CompactFlash Storage Cards, using the PCMCIA Soft Reset is considered a hard Reset by the ATA Commands. Contrast with Soft Reset in the Device Control Register. LevlREQ: this bit is set to one (1) when Level Mode Interrupt is selected, and zero (0) when Pulse Mode is selected. Set to zero (0) by Reset. Conf5 - Conf0 - Configuration Index: set to zero (0) by reset. It is used to select operation mode of the CompactFlash Storage Card as shown below. Note: Conf5 and Conf4 are reserved for CompactFlash Storage cards and shall be written as zero (0). Table: CompactFlash Storage Card Configurations 4.4 Card Configuration and Status Register (Base + 02h in Attribute Memory) The Card Configuration and Status Register contains information about the Card’s condition. Changed: indicates that one or both of the Pin Replacement register CReady, or CWProt bits are set to one (1). When the Changed bit is set, -STSCHG Pin 46 is held low if the SigChg bit is a One (1) and the CompactFlash Storage Card is configured for the I/O interface. SigChg: this bit is set and reset by the host to enable and disable a state-change “signal” from the Status Register, the Changed bit controls pin 46, the Changed Status signal. If no state change signal is desired, this bit is set to zero (0) and pin 46 (-STSCHG) signal is then held high while the CompactFlash Storage Card is configured for I/O. IOis8: the host sets this bit to a one (1) if the CompactFlash Storage Card is to be configured in an 8 bit I/O Mode. The Transcend Information Inc. 30 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card CompactFlash Storage Card is always configured for both 8 and 16 bit I/O, so this bit is ignored. -XE: For CompactFlash cards that do not support Power Level 1, this bit has value 0 and is not writeable. Audio:This bit should always be zero for CompactFlash Storage cards. PwrDwn: this bit indicates whether the host requests the CompactFlash Storage Card to be in the power saving or active mode. When the bit is one (1), the CompactFlash Storage Card enters a power down mode. When PwrDwn is zero (0), the host is requesting the CompactFlash Storage Card enter the active mode. The PCMCIA READY value becomes false (busy) when this bit is changed. READY shall not become true (ready) until the power state requested has been entered. The CompactFlash Storage Card automatically powers down when it is idle and powers back up when it receives a command. Int: this bit represents the internal state of the interrupt request. This value is available whether or not the I/O interface has been configured. This signal remains true until the condition that caused the interrupt request has been serviced. If interrupts are disabled by the -IEN bit in the Device Control Register, this bit is a zero (0). 4.5 Pin Replacement Register (Base + 04h in Attribute Memory) CReady: this bit is set to one (1) when the bit RReady changes state. This bit can also be written by the host. CWProt: this bit is set to one (1) when the RWprot changes state. This bit may also be written by the host. RReady: this bit is used to determine the internal state of the READY signal. This bit may be used to determine the state of the READY signal as this pin has been reallocated for use as Interrupt Request on an I/O card. When written, this bit acts as a mask (MReady) for writing the corresponding bit CReady. WProt: this bit is always zero (0) since the CompactFlash Storage Card does not have a Write Protect switch. When written, this bit acts as a mask for writing the corresponding bit CWProt. MReady: this bit acts as a mask for writing the corresponding bit CReady. MWProt: this bit when written acts as a mask for writing the corresponding bit CWProt. Table: Pin Replacement Changed Bit/Mask Bit Values Transcend Information Inc. 31 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 4.6 Socket and Copy Register (Base + 06h in Attribute Memory) This register contains additional configuration information. This register is always written by the system before writing the card’s Configuration Index Register. This register is not required for CF Cards. If present, it is optional for a CF Card to allow setting bit D4 (Drive number) to 1. If two drives are supported, it is intended for use only when two cards are co-located at either the primary or secondary addresses in PCMCIA I/O mode. The availability and capabilities of this register are described in the Card Information Structure of the CF Card. Hosts shall not depend on the availability of this functionality. Reserved: this bit is reserved for future standardization. This bit shall be set to zero (0) by the software when the register is written. Obsolete (Drive #): this bit is obsolete and should be written as 0. If the obsolete functionality is not supported it shall be read as written or shall be read as 0. If the obsolete functionality is supported, the bit shall be read as written. If supported, this bit sets the drive number, which the card matches with the DRV bit of the Drive/Head register when configured in a twin card configuration. It is recommended that the host always write 0 for the drive number in this register and in the DRV bit of the Drive/Head register for PCMCIA modes of operation. X: the socket number is ignored by the CompactFlash Storage Card. 4.7 I/O Transfer Function The I/O transfer to or from the CompactFlash Storage can be either 8 or 16 bits. When a 16 bit accessible Transcend Information Inc. 32 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card port is addressed, the signal -IOIS16 is asserted by the CompactFlash Storage. Otherwise, the -IOIS16 signal is de-asserted. When a 16 bit transfer is attempted, and the -IOIS16 signal is not asserted by the CompactFlash Storage, the system shall generate a pair of 8 bit references to access the word‘s even byte and odd byte. The CompactFlash Storage Card permits both 8 and 16 bit accesses to all of its I/O addresses, so -IOIS16 is asserted for all addresses to which the CompactFlash Storage responds. The CompactFlash Storage Card may request the host to extend the length of an input cycle until data is ready by asserting the -WAIT signal at the start of the cycle. Table: PCMCIA Mode I/O Function Function Code -REG -CE2 -CE1 A0 -IORD -IOWR D15-D8 D7-D0 Standby Mode X H H X X X High Z High Z Byte Input Access (8 bits) L L H H L L L H L L H H High Z High Z Even-Byte Odd-Byte Byte Output Access (8 bits) L L H H L L L H H H L L Don’t Care Don’t Care Even-Byte Odd-Byte Word Input Access (16 bits) L L L L L H Odd-Byte Even-Byte Word Output Access (16 bits) L L L L H L Odd-Byte Even-Byte I/O Read Inhibit H X X X L H Don’t Care Don’t Care I/O Write Inhibit H X X X H L High Z High Z High Byte Input Only (8 bits) L L H X L H Odd-Byte High Z High Byte Output Only (8 bits) L L H X H L Odd-Byte Don’t Care 4.8 Common Memory Transfer Function The Common Memory transfer to or from the CompactFlash Storage can be either 8 or 16 bits. Table: Common Memory Function Function Code -REG -CE2 -CE1 A0 -OE -WE D15-D8 D7-D0 Standby Mode X H H X X X High Z High Z Byte Read Access (8 bits) H H H H L L L H L L H H High Z High Z Even-Byte Odd-Byte Byte Write Access (8 bits) H H H H L L L H H H L L Don’t Care Don’t Care Even-Byte Odd-Byte Word Read Access (16 bits) H L L X L H Odd-Byte Even-Byte Word Write Access (16 bits) H L L X H L Odd-Byte Even-Byte Odd Byte Read Only (8 bits) H L H X L H Odd-Byte High Z Odd Byte Write Only (8 bits) H L H X H L Odd-Byte Don’t Care 4.9 True IDE Mode I/O Transfer Function Transcend Information Inc. 33 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card The CompactFlash Storage Card can be configured in a True IDE Mode of operation. The CompactFlash Storage Card is configured in this mode only when the -OE input signal is grounded by the host during the power off to power on cycle. Optionally, CompactFlash Storage Cards may support the following optional detection methods: 1. The card is permitted to monitor the –OE (-ATA SEL) signal at any time(s) and switch to PCMCIA mode upon detecting a high level on the pin. 2. The card is permitted to re-arbitrate the interface mode determination following a transition of the (-)RESET pin. 3. The card is permitted to monitor the –OE (-ATA SEL) signal at any time(s) and switch to True IDE mode upon detection of a continuous low level on pin for an extended period of time. Notes: 1) Implemented for backward compatibility. Bit D7 of the register shall remain High Z to prevent conflict with any floppy disk controller at the same address. The host software should not rely on the contents of this register. Transcend Information Inc. 34 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 4.10 Host Configuration Requirements for Master/Slave or New Timing Modes The CF Advanced Timing modes include PCMCIA PC Card style I/O modes that are faster than the original 250 ns cycle time. These modes are not supported by the PCMCIA PC Card specification nor CF by cards based on revisions of the CF specification before Revision 3.0. Hosts shall ensure that all cards accessed through a common electrical interface are capable of operation at the desired, faster than 250 ns, I/O mode before configuring the interface for that I/O mode. Advanced Timing modes are PCMCIA PC Card style I/O modes that are 100 ns or faster, PC Card Memory modes that are 100ns or faster, True IDE PIO Modes 5,6 and Multiword DMA Modes 3,4. These modes are permitted to be used only when a single card is present and the host and card are connected directly, without a cable exceeding 0.15m in length. Consequently, the host shall not configure a card into an Advanced Timing Mode if two cards are sharing I/O lines, as in Master/Slave operation, nor if it is constructed such that a cable exceeding 0.15 meters is required to connect the host to the card. When the use of two cards on an interface is otherwise permitted, the host may use any mode that is supported by both cards, but to achieve maximum performance it should use its highest performance mode that is also supported by both cards. 5 CF-ATA Drive Register Set Definition and Protocol The CompactFlash Storage Card can be configured as a high performance I/O device through: a) The standard PC-AT disk I/O address spaces 1F0h-1F7h, 3F6h-3F7h (primary) or 170h- 177h, 376h-377h (secondary) with IRQ 14 (or other available IRQ). b) Any system decoded 16 byte I/O block using any available IRQ. c) Memory space. The communication to or from the CompactFlash Storage Card is done using the Task File registers, which provide all the necessary registers for control and status information related to the storage medium. The PCMCIA interface connects peripherals to the host using four register mapping methods. Table is a detailed description of these methods below: Table: I/O Configurations Transcend Information Inc. 35 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.1 I/O Primary and Secondary Address Configurations Table: Primary and Secondary I/O Decoding Note: 1) Register 0 is accessed with -CE1 low and -CE2 low (and A0 = Don’t Care) as a word register on the combined Odd Data Bus and Even Data Bus (D15-D0). This register may also be accessed by a pair of byte accesses to the offset 0 with -CE1 low and -CE2 high. Note that the address space of this word register overlaps the address space of the Error and Feature byte-wide registers, which lie at offset 1. When accessed twice as byte register with -CE1 low, the first byte to be accessed is the even byte of the word and the second byte accessed is the odd byte of the equivalent word access. 2) A byte access to register 0 with -CE1 high and -CE2 low accesses the error (read) or feature (write) register. Transcend Information Inc. 36 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.2 Contiguous I/O Mapped Addressing When the system decodes a contiguous block of I/O registers to select the CompactFlash Storage Card, the registers are accessed in the block of I/O space decoded by the system as follows: Table: Contiguous I/O Decoding Notes: 1) Register 0 is accessed with -CE1 low and -CE2 low (and A0 = Don’t Care) as a word register on the combined Odd Data Bus and Even Data Bus (D15-D0). This register may also be accessed by a pair of byte accesses to the offset 0 with -CE1 low and -CE2 high. Note that the address space of this word register overlaps the address space of the Error and Feature byte-wide registers that lie at offset 1. When accessed twice as byte register with -CE1 low, the first byte to be accessed is the even byte of the word and the second byte accessed is the odd byte of the equivalent word access. A byte access to register 0 with -CE1 high and -CE2 low accesses the error (read) or feature (write) register. 2) Registers at offset 8, 9 and D are non-overlapping duplicates of the registers at offset 0 and 1. Register 8 is equivalent to register 0, while register 9 accesses the odd byte. Therefore, if the registers are byte accessed in the order 9 then 8 the data shall be transferred odd byte then even byte. Repeated byte accesses to register 8 or 0 shall access consecutive (even than odd) bytes from the data buffer. Repeated word accesses to register 8, 9 or 0 shall access consecutive words from the data buffer. Repeated byte accesses to register 9 are not supported. However, repeated alternating byte accesses to registers 8 then 9 shall access consecutive (even then odd) bytes from the data buffer. Byte accesses to register 9 access only the odd byte of the data. 3) Address lines that are not indicated are ignored by the CompactFlash Storage Card for accessing all the registers in this table. Transcend Information Inc. 37 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.3 Memory Mapped Addressing When the CompactFlash Storage Card registers are accessed via memory references, the registers appear in the common memory space window: 0-2K bytes as follows: Notes: 1) Register 0 is accessed with -CE1 low and -CE2 low as a word register on the combined Odd Data Bus and Even Data Bus (D15-D0). This register may also be accessed by a pair of byte accesses to the offset 0 with -CE1 low and -CE2 high. Note that the address space of this word register overlaps the address space of the Error and Feature byte-wide registers that lie at offset 1. When accessed twice as byte register with -CE1 low, the first byte to be accessed is the even byte of the word and the second byte accessed is the odd byte of the equivalent word access. A byte access to address 0 with -CE1 high and -CE2 low accesses the error (read) or feature (write) register. 2) Registers at offset 8, 9 and D are non-overlapping duplicates of the registers at offset 0 and 1.Register 8 is equivalent to register 0, while register 9 accesses the odd byte. Therefore, if the registers are byte accessed in the order 9 then 8 the data shall be transferred odd byte then even byte. Repeated byte accesses to register 8 or 0 shall access consecutive (even then odd) bytes from the data buffer. Repeated word accesses to register 8, 9 or 0 shall access consecutive words from the data buffer. Repeated byte accesses to register 9 are not supported. However, repeated alternating byte accesses to registers 8 then 9 shall access consecutive (even then odd) bytes from the data buffer. Byte accesses to register 9 access only the odd byte of the data. 3) Accesses to even addresses between 400h and 7FFh access register 8. Accesses to odd addresses between 400h and 7FFh access register 9. This 1 Kbyte memory window to the data register is provided so that hosts can perform memory to memory block moves to the data register when the register lies in memory space. Transcend Information Inc. 38 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Some hosts, such as the X86 processors, must increment both the source and destination addresses when executing the memory to memory block move instruction. Some PCMCIA socket adapters also have auto incrementing address logic embedded within them. This address window allows these hosts and adapters to function efficiently. Note that this entire window accesses the Data Register FIFO and does not allow random access to the data buffer within the CompactFlash Storage Card. A word access to address at offset 8 shall provide even data on the low-order byte of the data bus, along with odd data at offset 9 on the high-order byte of the data bus. 5.4 True IDE Mode Addressing When the CompactFlash Storage Card is configured in the True IDE Mode, the I/O decoding is as follows: Note: 1) See the section 6.1.5 CF-ATA Registers for information regarding the control of 8 or 16 bit transfers to the data register. 5.5 CF-ATA Registers The following section describes the hardware registers used by the host software to issue commands to the CompactFlash device. These registers are often collectively referred to as the “task file.” Note: In accordance with the PCMCIA specification: each of the registers below that is located at an odd offset address may be accessed in the PC Card Memory or PC Card I/O modes at its normal address and also the corresponding even address (normal address -1) using data bus lines (D15-D8) when -CE1 is high and -CE2 is low unless -IOIS16 is high (not asserted by the card) and an I/O cycle is being performed. In the True IDE mode of operation, the size of the transfer is based solely on the register being addressed. All registers are 8 bit only except for the Data Register, which is normally 16 bits, but can be programmed to use 8 bit transfers for Non-DMA operations through the use of the Set Features command. The data register is also 8 bits during a portion of the Read Long and Write Long commands, which exist solely for historical reasons and should not be used. 5.5.1 Data Register (Address - 1F0h[170h];Offset 0,8,9) The Data Register is a 16 bit register, and it is used to transfer data blocks between the CompactFlash Storage Card data buffer and the Host. This register overlaps the Error Register Table: Data Register Access below describes the combinations of data register access and is provided to assist in understanding the overlapped Data Register and Error/Feature Register rather than to attempt to define general PCMCIA word and byte access modes and operations. See the PCMCIA PC Card Standard, for further definitions of the Card Accessing Modes for I/O and Memory cycles. Transcend Information Inc. 39 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Note: Because of the overlapped registers, PC Card modes access to the 1F1h, 171h or offset 1 are not defined for word (-CE2 = 0 and -CE1 = 0) operations. These accesses are treated as accesses to the Word Data Register. The duplicated registers at offsets 8, 9 and Dh have no restrictions on the operations that can be performed by the socket. Table: Data Register Access Notes: 1) -REG signal is mode dependent. Signal shall be 0 for I/O mode and 1 for Memory Mode. 5.5.2 Error Register (Address - 1F1h[171h]; Offset 1, 0Dh Read Only) This register contains additional information about the source of an error when an error is indicated in bit 0 of the Status register. The bits are defined as follows: Figure: Error Register This register is also accessed in PC Card Modes on data bits D15-D8 during a read operation to offset 0 with -CE2 low and -CE1 high. Bit 7 (BBK): this bit is set when a Bad Block is detected. Bit 6 (UNC): this bit is set when an Uncorrectable Error is encountered. Bit 5: this bit is 0. Bit 4 (IDNF): the requested sector ID is in error or cannot be found. Bit 3: this bit is 0. Bit 2 (Abort) This bit is set if the command has been aborted because of a CompactFlash Storage Card status condition: (Not Ready, Write Fault, etc.) or when an invalid command has been issued. Bit 1 This bit is 0. Bit 0 (AMNF) This bit is set in case of a general error. Transcend Information Inc. 40 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.5.3 Feature Register (Address - 1F1h[171h]; Offset 1, 0Dh Write Only) This register provides information regarding features of the CompactFlash Storage Card that the host can utilize. This register is also accessed in PC Card modes on data bits D15-D8 during a write operation to Offset 0 with -CE2 low and -CE1 high. 5.5.4 Sector Count Register (Address - 1F2h[172h]; Offset 2) This register contains the numbers of sectors of data requested to be transferred on a read or write operation between the host and the CompactFlash Storage Card. If the value in this register is zero, a count of 256 sectors is specified. If the command was successful, this register is zero at command completion. If not successfully completed, the register contains the number of sectors that need to be transferred in order to complete the request. 5.5.5 Sector Number (LBA 7-0) Register (Address - 1F3h[173h]; Offset 3) This register contains the starting sector number or bits 7-0 of the Logical Block Address (LBA) for any CompactFlash Storage Card data access for the subsequent command. 5.5.6 Cylinder Low (LBA 15-8) Register (Address - 1F4h[174h]; Offset 4) This register contains the low order 8 bits of the starting cylinder address or bits 15-8 of the Logical Block Address. 5.5.7 Cylinder High (LBA 23-16) Register (Address - 1F5h[175h]; Offset 5) This register contains the high order bits of the starting cylinder address or bits 23-16 of the Logical Block Address. 5.5.8 Drive/Head (LBA 27-24) Register (Address 1F6h[176h]; Offset 6) The Drive/Head register is used to select the drive and head. It is also used to select LBA addressing instead of cylinder/head/sector addressing. The bits are defined as follows: Figure: Drive/Head Register Bit 7: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become obsolete in a future revision of the specification. This bit is ignored by some controllers in some commands. Bit 6: LBA is a flag to select either Cylinder/Head/Sector (CHS) or Logical Block Address Mode (LBA). When LBA=0, Cylinder/Head/Sector mode is selected. When LBA=1, Logical Block Address is selected. In Logical Block Mode, the Logical Block Address is interpreted as follows: LBA7-LBA0: Sector Number Register D7-D0. LBA15-LBA8: Cylinder Low Register D7-D0. LBA23-LBA16: Cylinder High Register D7-D0. LBA27-LBA24: Drive/Head Register bits HS3-HS0. Bit 5: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become obsolete in a future revisions of the specification. This bit is ignored by some controllers in some commands. Bit 4 (DRV): DRV is the drive number. When DRV=0, drive (card) 0 is selected. When DRV=1, drive (card) 1 is selected. Setting this bit to 1 is obsolete in PCMCIA modes of operation. If the obsolete functionality is support by a CF Storage Card, the CompactFlash Storage Card is set to be Card 0 or 1 using the copy field (Drive #) of the PCMCIA Socket & Copy configuration register. Bit 3 (HS3): when operating in the Cylinder, Head, Sector mode, this is bit 3 of the head number. Transcend Information Inc. 41 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card It is Bit 27 in the Logical Block Address mode. Bit 2 (HS2): when operating in the Cylinder, Head, Sector mode, this is bit 2 of the head number. It is Bit 26 in the Logical Block Address mode. Bit 1 (HS1): when operating in the Cylinder, Head, Sector mode, this is bit 1 of the head number. It is Bit 25 in the Logical Block Address mode. Bit 0 (HS0): when operating in the Cylinder, Head, Sector mode, this is bit 0 of the head number. It is Bit 24 in the Logical Block Address mode. 5.5.9 Status & Alternate Status Registers (Address 1F7h[177h]&3F6h[376h]; Offsets 7 & Eh) These registers return the CompactFlash Storage Card status when read by the host. Reading the Status register does clear a pending interrupt while reading the Auxiliary Status register does not. The status bits are described as follows: Figure: Status & Alternate Status Register Bit 7 (BUSY): the busy bit is set when the CompactFlash Storage Card has access to the command buffer and registers and the host is locked out from accessing the command register and buffer. No other bits in this register are valid when this bit is set to a 1. During the data transfer of DMA commands, the Card shall not assert DMARQ unless either the BUSY bit, the DRQ bit, or both are set to one. Bit 6 (RDY): RDY indicates whether the device is capable of performing CompactFlash Storage Card operations. This bit is cleared at power up and remains cleared until the CompactFlash Storage Card is ready to accept a command. Bit 5 (DWF): This bit, if set, indicates a write fault has occurred. Bit 4 (DSC): This bit is set when the CompactFlash Storage Card is ready. Bit 3 (DRQ): The Data Request is set when the CompactFlash Storage Card requires that information be transferred either to or from the host through the Data register. During the data transfer of DMA commands, the Card shall not assert DMARQ unless either the BUSY bit, the DRQ bit, or both are set to one. Bit 2 (CORR): This bit is set when a Correctable data error has been encountered and the data has been corrected. This condition does not terminate a multi-sector read operation. Bit 1 (IDX): This bit is always set to 0. Bit 0 (ERR): This bit is set when the previous command has ended in some type of error. The bits in the Error register contain additional information describing the error. It is recommended that media access commands (such as Read Sectors and Write Sectors) that end with an error condition should have the address of the first sector in error in the command block registers. 5.5.10 Device Control Register (Address - 3F6h[376h]; Offset Eh) This register is used to control the CompactFlash Storage Card interrupt request and to issue an ATA soft reset to the card. This register can be written even if the device is BUSY. The bits are defined as follows: Transcend Information Inc. 42 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Figure: Device Control Register Bit 7: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0. Bit 6: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0. Bit 5: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0. Bit 4: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0. Bit 3: this bit is ignored by the CompactFlash Storage Card. The host software should set this bit to 0. Bit 2 (SW Rst): this bit is set to 1 in order to force the CompactFlash Storage Card to perform an AT Disk controller Soft Reset operation. This does not change the PCMCIA Card Configuration Registers (see Section 4.3 to 4.7) as a hardware Reset does. The Card remains in Reset until this bit is reset to ‘0.’ Bit 1 (-IEn): the Interrupt Enable bit enables interrupts when the bit is 0. When the bit is 1, interrupts from the CompactFlash Storage Card are disabled. This bit also controls the Int bit in the Configuration and Status Register. This bit is set to 0 at power on and Reset. Bit 0: this bit is ignored by the CompactFlash Storage Card. 5.5.11 Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh) This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host’s I/O space because of potential conflicts on Bit 7. The bits are defined as follows: Bit 7: this bit is unknown. Implementation Note: Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller operating at the same addresses as the CompactFlash Storage Card. Following are some possible solutions to this problem for the PCMCIA implementation: 1) Locate the CompactFlash Storage Card at a non-conflicting address, i.e. Secondary address (377) or in an independently decoded Address Space when a Floppy Disk Controller is located at the Primary addresses. 2) Do not install a Floppy and a CompactFlash Storage Card in the system at the same time. 3) Implement a socket adapter that can be programmed to (conditionally) tri-state D7 of I/0 address 3F7h/377h when a CompactFlash Storage Card is installed and conversely to tristate D6-D0 of I/O address 3F7h/377h when a floppy controller is installed. 4) Do not use the CompactFlash Storage Card’s Drive Address register. This may be accomplished by either a) If possible, program the host adapter to enable only I/O addresses 1F0h-1F7h, 3F6h (or 170h-177h, 176h) to the CompactFlash Storage Card or b) if provided use an additional Primary / Secondary configuration in the CompactFlash Storage Card which does not respond to accesses to I/O locations 3F7h and 377h. With either of these implementations, the host software shall not attempt to use information in the Drive Address Register. Bit 6 (-WTG): this bit is 0 when a write operation is in progress; otherwise, it is 1. Bit 5 (-HS3): this bit is the negation of bit 3 in the Drive/Head register. Transcend Information Inc. 43 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Bit 4 (-HS2): this bit is the negation of bit 2 in the Drive/Head register. Bit 3 (-HS1): this bit is the negation of bit 1 in the Drive/Head register. Bit 2 (-HS0): this bit is the negation of bit 0 in the Drive/Head register. Bit 1 (-nDS1): this bit is 0 when drive 1 is active and selected. Bit 0 (-nDS0): this bit is 0 when the drive 0 is active and selected. 5.6 CF-ATA Command Description This section defines the software requirements and the format of the commands the host sends to the CompactFlash Storage Cards. Commands are issued to the CompactFlash Storage Card by loading the required registers in the command block with the supplied parameters, and then writing the command code to the Command Register. The manner in which a command is accepted varies. There are three classes (see Table 38: CF-ATA Command Set) of command acceptance, all dependent on the host not issuing commands unless the CompactFlash Storage Card is not busy (BSY=0). All commands listed in this specification shall be implemented. Upon receipt of a Class 1 command, the CompactFlash Storage Card sets BSY within 400 nsec. Upon receipt of a Class 2 command, the CompactFlash Storage Card sets BSY within 400 nsec, sets up the sector buffer for a write operation, sets DRQ within 700 µsec, and clears BSY within 400 nsec of setting DRQ. Upon receipt of a Class 3 command, the CompactFlash Storage Card sets BSY within 400nsec, sets up the sector buffer for a write operation, sets DRQ within 20 msec (assuming no re-assignments), and clears BSY within 400 nsec of setting DRQ. Transcend Information Inc. 44 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.1 CF-ATA Command Set CF-ATA Command Set summarizes the CF-ATA command set with the paragraphs that follow describing the individual commands and the task file for each. FR SC SN CY DH LBA E5 or 98h – – – – Y – Support Execute Drive Diagnostic 90h – – – – Y – Support 3 Erase Sector C0h – Y Y Y Y Y Support 4 Flush Cache E7h – – – – Y – NOT Support 5 Format Track 50h – Y – Y Y Y Support 6 Identify Device ECh – – – – Y – Support 7 Idle E3h or 97h – Y – – Y – Support 8 Idle Immediate E1h or 95h – – – – Y – Support 9 Initialize Drive Parameters 91h – Y – – Y – Support 10 Key Management Structure Read B9 (Feature 0-127) Y Y Y Y Y – NOT Support #1 11 Key Management Read Keying Material B9 (Feature 80) Y Y Y Y Y – NOT Support #1 12 Key Management Change Key Management Value B9 (Feature 81) Y Y Y Y Y – NOT Support #1 13 NOP 00h – – – – Y – NOT Support 14 Read Buffer E4h – – – – Y – Support 15 Read DMA C8h – Y Y Y Y Y Support 16 Read Long Sector 22h or 23h – Y Y Y Y NOT Support 17 Read Multiple C4h – Y Y Y Y Y Support 18 Read Sector(s) 20h or 21h – Y Y Y Y Y Support 19 Read Verify Sector(s) 40h or 41h – Y Y Y Y Y Support 20 Recalibrate 1Xh – – – – Y 21 Request Sense 03h – – – – Y – Support 22 Security Disable Password F6h – – – – Y – NOT Support #2 23 Security Erase Prepare F3h – – – – Y – NOT Support #2 24 Security Erase Unit F4h – – – – Y – NOT Support #2 25 Security Freeze Lock F5h – – – – Y – NOT Support #2 26 Security Set Password F1h – – – – Y – NOT Support #2 27 Security Unlock F2h – – – – Y – NOT Support #2 Command Code 1 Check Power Mode 2 Transcend Information Inc. 45 – Status Note #3 #3 Support V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Command Code FR SC SN CY DH LBA 28 Seek 29 Status 7Xh – – Y Y Y Y Support Set Feature EFh Y – – – Y – Support 30 Set Multiple Mode C6h – Y – – Y – Support 31 Set Sleep Mode E6h or 99h – – – – Y – Support 32 Standby E2 or 96h – – – – Y – Support 33 Standby Immediate E0 or 94h – – – – Y – Support 34 Translate Sector 87h – Y Y Y Y Y Support 35 Wear Level F5h – – – – Y – Support 36 Write Buffer E8h – – – – Y – Support 37 Write DMA CAh – Y Y Y Y Y Support 38 Write Long Sector 32h or 33h – – Y Y Y Y Not Support 39 Write Multiple C5h – Y Y Y Y Y Support 40 Write Multiple w/o Erase CDh – Y Y Y Y Y Support 41 Write Sector(s) 30h or 31h – Y Y Y Y Y Support 42 Write Sector(s) w/o Erase 38h – Y Y Y Y Y Support 43 Write Verify 3Ch – Y Y Y Y Y Support Note #3 #1: This command is optional, depending on the key Management scheme in use. #2: Use of this command is not recommended by CFA #3: Use of this command is not recommended. Definitions FR = Features Register SC =Sector Count register (00H to FFH, 00H means 256 sectors) SN = Sector Number register CY = Cylinder Low/High register DH = Head No. (0 to 15) of Drive/Head register LBA = Logic Block Address Mode Support – = Not used for the command Y = Used for the command Transcend Information Inc. 46 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.2 Check Power Mode - 98h or E5h If the CompactFlash Storage Card is in, going to, or recovering from the sleep mode, the CompactFlash Storage Card sets BSY, sets the Sector Count Register to 00h, clears BSY and generates an interrupt. If the CompactFlash Storage Card is in Idle mode, the CompactFlash Storage Card sets BSY, sets the Sector Count Register to FFh, clears BSY and generates an interrupt. Bit -> 7 6 5 4 Command (7) 3 2 1 0 98h or E5h C/D/H (6) X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X 5.6.3 Execute Drive Diagnostic - 90h When the diagnostic command is issued in a PCMCIA configuration mode, this command runs only on the CompactFlash Storage Card that is addressed by the Drive/Head register. This is because PCMCIA card interface does not allows for direct inter-drive communication (such as the ATA PDIAG and DASP signals). When the diagnostic command is issued in the True IDE Mode, the Drive bit is ignored and the diagnostic command is executed by both the Master and the Slave with the Master responding with status for both devices. Bit -> 7 6 5 4 Command (7) 3 2 1 0 90h C/D/H (6) X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X Diagnostic Codes are returned in the Error Register at the end of the command. Code Error Type 01h No Error Detected 02h Formatter Device Error 03h Sector Buffer Error 04h ECC Circuitry Error 05h Controlling Microprocessor Error 8Xh Slave Error in True IDE Mode Transcend Information Inc. 47 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.4 Erase Sector(s) - C0h This command is used to pre-erase and condition data sectors in advance of a Write without Erase or Write Multiple without Erase command. There is no data transfer associated with this command but a Write Fault error status can occur. Bit -> 7 6 5 4 Command (7) C/D/H (6) 3 2 1 0 C0h 1 LBA 1 Drive Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) Sector Number (LBA 7-0) Sec Cnt (2) Sector Count Feature (1) X 5.6.5 Format Track - 50h This command writes the desired head and cylinder of the selected drive with a vendor unique data pattern (typically FFh or 00h). To remain host backward compatible, the CompactFlash Storage Card expects a sector buffer of data from the host to follow the command with the same protocol as the Write Sector(s) command although the information in the buffer is not used by the CompactFlash Storage Card. If LBA=1 then the number of sectors to format is taken from the Sec Cnt register (0=256). The use of this command is not recommended. Bit -> 7 6 5 4 Command (7) C/D/H (6) 3 2 0 50h 1 LBA 1 Drive Head (LBA 27-24) Cyl High (5) Cylinder High (LBA 23-16) Cyl Low (4) Cylinder Low (LBA 15-8) Sec Num (3) X (LBA 7-0) Sec Cnt (2) Count (LBA mode only) Feature (1) X Transcend Information Inc. 1 48 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.6 Identify Device – Ech Bit -> 7 6 5 4 Command (7) C/D/H (6) 3 2 1 0 ECh X X X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X The Identify Device command enables the host to receive parameter information from the CompactFlash Storage Card. This command has the same protocol as the Read Sector(s) command. The parameter words in the buffer have the arrangement and meanings defined in Table as below. All reserved bits or words are zero. Hosts should not depend on Obsolete words in Identify Device containing 0. Table specifies each field in the data returned by the Identify Device Command. In Table as below, X indicates a numeric nibble value specific to the card and aaaa indicates an ASCII string specific to the particular drive. Word Address Default Value Total Bytes 848Ah 2 General configuration - signature for the CompactFlash 0 lash Storage Card 0XXX 2 General configuration – Bit Significant with ATA-4 definitions. 1 XXXXh 2 Default number of cylinders 2 0000h 2 Reserved 3 00XXh 2 Default number of heads 4 0000h 2 Obsolete 5 0000h 2 Obsolete 6 XXXXh 2 Default number of sectors per track 7-8 XXXXh 4 Number of sectors per card (Word 7 = MSW, Word 8 = LSW) 9 XXXXh 2 Obsolete 10-19 aaaa 20 Serial number in ASCII (Right Justified) 20 0000h 2 Obsolete 21 0000h 2 Obsolete 22 0004h 2 Number of ECC bytes passed on Read/Write Long Commands 23-26 aaaa 8 Firmware revision in ASCII. Big Endian Byte Order in Word 27-46 aaaa 40 Model number in ASCII (Left Justified) Big Endian Byte Order in Word 47 XXXXh 2 Maximum number of sectors on Read/Write Multiple command 48 0000h 2 Reserved 49 XX00h 2 Capabilities 50 0000h 2 Reserved 0 Transcend Information Inc. Data Field Type Information 49 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Word Address Default Value Total Bytes 51 0X00h 2 PIO data transfer cycle timing mode 52 0000h 2 Obsolete 53 000Xh 2 Field Validity 54 XXXXh 2 Current numbers of cylinders 55 XXXXh 2 Current numbers of heads Data Field Type Information 56 XXXXh 2 Current sectors per track 57-58 XXXXh 4 Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW) 59 01XXh 2 Multiple sector setting 60-61 XXXXh 4 Total number of sectors addressable in LBA Mode 62 0000h 2 Reserved 63 0X0Xh 2 Multiword DMA transfer. In PC Card modes this value shall be 0h 64 00XXh 2 Advanced PIO modes supported 65 XXXXh 2 Minimum Multiword DMA transfer cycle time per word. In PC Card modes this value shall be 0h 66 XXXXh 2 Recommended Multiword DMA transfer cycle time. In PC Card modes this value shall be 0h 67 XXXXh 2 Minimum PIO transfer cycle time without flow control 68 XXXXh 2 Minimum PIO transfer cycle time with IORDY flow control 69-79 0000h 20 Reserved 80-81 0000h 4 Reserved – CF cards do not return an ATA version 82-84 XXXXh 6 Features/command sets supported 85-87 XXXXh 6 Features/command sets enabled 88 XXXXh 2 Reserved 89 XXXXh 2 Time required for Security erase unit completion 90 XXXXh 2 Time required for Enhanced security erase unit completion 91 XXXXh 2 Current Advanced power management value 92-127 0000h 72 Reserved 128 XXXXh 2 Security status 129-159 0000h 64 Vendor unique bytes 160 XXXXh 2 Power requirement description 161 0000h 2 Reserved for assignment by the CFA 162 0000h 2 Key management schemes supported 163 XXXXh 2 CF Advanced True IDE Timing Mode Capability and Setting 164 XXXXh 2 CF Advanced PC Card I/O and Memory Timing Mode Capability 165-167 0000h 6 Reserved for assignment by the CFA 168-255 0000h 158 Transcend Information Inc. Reserved 50 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Word 0: General Configuration This field indicates the general characteristics of the device. When Word 0 of the Identify drive information is 848Ah then the device is a CompactFlash Storage Card and complies with the CFA specification and CFA command set. It is recommended that PCMCIA modes of operation report only the 848Ah value as they are always intended as removable devices. Bits 15-0: CF Standard Configuration Value Word 0 is 848Ah. This is the recommended value of Word 0. Some operating systems require Bit 6 of Word 0 to be set to 1 (Non-removable device) to use the card as the root storage device. The Card must be the root storage device when a host completely replaces conventional disk storage with a CompactFlash Card in True IDE mode. To support this requirement and provide capability for any future removable media Cards, alternatehandling of Word 0 is permitted. Bits 15-0: CF Preferred Alternate Configuration Values 044Ah: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while preserving all Retired bits in the word. 0040h: This is the alternate value of Word 0 turns on ATA device and turns off Removable Media and Removable Device while zeroing all Retired bits in the word Bit 15-12: Configuration Flag If bits 15:12 are set to 8h then Word 0 shall be 848Ah. If bits 15:12 are set to 0h then Bits 11:0 are set using the definitions below and the Card is required to support for the CFA command set and report that in bit 2 of Word 83. Bit 15:12 values other than 8h and 0h are prohibited. Bits 11-8: Retired These bits have retired ATA bit definitions. It is recommended that the value of these bits be either the preferred value of 0h or the value of 4h that preserves the corresponding bits from the 848Ah CF signature value. Bit 7: Removable Media Device If Bit 7 is set to 1, the Card contains media that can be removed during Card operation. If Bit 7 is set to 0, the Card contains nonremovable media. Bit 6: Not Removable Controller and/or Device Alert! This bit will be considered for obsolescence in a future revision of this standard. If Bit 6 is set to 1, the Card is intended to be nonremovable during operation. If Bit 6 is set to 0, the Card is intended to be removable during operation. Bits 5-0: Retired/Reserved Alert! Bit 2 will be considered for definition in a future revision of this standard and shall be 0 at this time. Bits 5-1 have retired ATA bit definitions. Bit 2 shall be 0. Bit 0 is Reserved and shall be 0. It is recommended that the value of bits 5-0 be either the preferred value of 00h or the value of 0Ah that preserves the corresponding bits from the 848Ah CF signature value. Word 1: Default Number of Cylinders This field contains the number of translated cylinders in the default translation mode. This value will be the same as the number of cylinders. Word 3: Default Number of Heads This field contains the number of translated heads in the default translation mode. Word 6: Default Number of Sectors per Track This field contains the number of sectors per track in the default translation mode. Transcend Information Inc. 51 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Words 7-8: Number of Sectors per Card This field contains the number of sectors per CompactFlash Storage Card. This double word value is also the first invalid address in LBA translation mode. Words 10-19: Serial Number This field contains the serial number for this CompactFlash Storage Card and is right justified and padded with spaces (20h). Word 22: ECC Count This field defines the number of ECC bytes used on each sector in the Read and Write Long commands. This value shall be set to 0004h. Words 23-26: Firmware Revision This field contains the revision of the firmware for this product. Words 27-46: Model Number This field contains the model number for this product and is left justified and padded with spaces (20h). Word 47: Read/Write Multiple Sector Count Bits 15-8 shall be the recommended value of 80h or the permitted value of 00h. Bits 7-0 of this word define the maximum number of sectors per block that the CompactFlash Storage Card supports for Read/Write Multiple commands. Word 49: Capabilities Bit 13: Standby Timer If bit 13 is set to 1 then the Standby timer is supported as defined by the IDLE command If bit 13 is set to 0 then the Standby timer operation is defined by the vendor. Bit 11: IORDY Supported If bit 11 is set to 1 then this CompactFlash Storage Card supports IORDY operation. If bit 11 is set to 0 then this CompactFlash Storage Card may support IORDY operation. Bit 10: IORDY may be disabled Bit 10 shall be set to 0, indicating that IORDY may not be disabled. Bit 9: LBA supported Bit 9 shall be set to 1, indicating that this CompactFlash Storage Card supports LBA mode addressing. CF devices shall support LBA addressing. Bit 8: DMA Supported If bit 8 is set to 1 then Read DMA and Write DMA commands are supported. Bit 8 shall be set to 0. Read/Write DMA commands are not currently permitted on CF cards. PIO Data Transfer Cycle Timing Mode The PIO transfer timing for each CompactFlash Storage Card falls into modes that have unique parametric timing specifications. The value returned in Bits 15-8 shall be 00h for mode 0, 01h for mode 1, or 02h for mode 2. Values 03h through FFh are reserved. Translation Parameters Valid Bit 0 shall be set to 1 indicating that words 54 to 58 are valid and reflect the current number of cylinders, heads and sectors. If bit 1 of word 53 is set to 1, the values in words 64 through 70 are valid. If this bit is cleared to 0, the values reported in words 64-70 are not valid. Any CompactFlash Storage Card that supports PIO mode 3 or above shall set bit 1 of word 53 to one and support the fields contained in words 64 through 70. Current Number of Cylinders, Heads, Sectors/Track These fields contains the current number of user addressable Cylinders, Heads, and Sectors/Track in the current translation mode. Current Capacity This field contains the product of the current cylinders times heads times sectors. Multiple Sector Setting Bits 15-9 are reserved and shall be set to 0. Bit 8 shall be set to 1 indicating that the Multiple Sector Setting is valid. Bits 7-0 are the current setting for the number of sectors that shall be transferred per interrupt on Read/Write Multiple commands. Total Sectors Addressable in LBA Mode Transcend Information Inc. 52 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card This field contains the total number of user addressable sectors for the CompactFlash Storage Card in LBA mode only. Multiword DMA transfer Bits 15 through 8 of word 63 of the Identify Device parameter information is defined as the Multiword DMA mode selected field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Only one of bits may be set to one in this field by the CompactFlash Storage Card to indicate the multiword DMA mode which is currently selected. Of these bits, bits 15 through 11 are reserved. Bit 8, if set to one, indicates that Multiword DMA mode 0 has been selected. Bit 9, if set to one, indicates that Multiword DMA mode 1 has been selected. Bit 10, if set to one, indicates that Multiword DMA mode 2 has been selected. Selection of Multiword DMA modes 3 and above are specific to CompactFlash are reported in word 163, Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings. Bits 7 through 0 of word 63 of the Identify Device parameter information is defined as the Multiword DMA data transfer supported field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to indicate the Multiword DMA modes it is capable of supporting. Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA mode 0. Bit 1, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA modes 1 and 0. Bit 2, if set to one, indicates that the CompactFlash Storage Card supports Multiword DMA modes 2, 1 and 0. Support for Multiword DMA modes 3 and above are specific to CompactFlash are reported in word 163, Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings. Word 64: Advanced PIO transfer modes supported Bits 7 through 0 of word 64 of the Identify Device parameter information is defined as the advanced PIO data transfer supported field. If this field is supported, bit 1 of word 53 shall be set to one. This field is bit significant. Any number of bits may be set to one in this field by the CompactFlash Storage Card to indicate the advanced PIO modes it is capable of supporting. Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports PIO mode 3. Bit 1, if set to one, indicates that the CompactFlash StorageCard supports PIO mode 4. Support for PIO modes 5 and above are specific to CompactFlash are reported in word 163. Word 65: Minimum Multiword DMA transfer cycle time Word 65 of the parameter information of the Identify Device command is defined as the minimum Multiword DMA transfer cycle time. This field defines, in nanoseconds, the minimum cycle time that, if used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer. If this field is supported, bit 1 of word 53 shall be set to one. The value in word 65 shall not be less than the minimum cycle time for the fastest DMA mode supported by the device. This field shall be supported by all CompactFlash Storage Cards supporting DMA modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a value of zero in this field. Recommended Multiword DMA transfer cycle time Word 66 of the parameter information of the Identify Device command is defined as the recommended Multiword DMA transfer cycle time. This field defines, in nanoseconds, the cycle time that, if used by the host, may optimize the data transfer from by reducing the probability that the CompactFlash Storage Card will need to negate the DMARQ signal during the transfer of a sector. If this field is supported, bit 1 of word 53 shall be set to one. The value in word 66 shall not be less than the value in word 65. This field shall be supported by all CompactFlash Storage Cards supporting DMA modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a value of zero in this field. Word 67: Minimum PIO transfer cycle time without flow control Word 67 of the parameter information of the Identify Device command is defined as the minimum PIO transfer without flow control cycle time. This field defines, in nanoseconds, the minimum cycle time that, if used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer without utilization of flow control. If this field is supported, Bit 1 of word 53 shall be set to one. Any CompactFlash Storage Card that supports PIO mode 3 or above shall support this field, and the value in word 67 shall not Transcend Information Inc. 53 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card be less than the value reported in word 68. If bit 1 of word 53 is set to one because a CompactFlash Storage Card supports a field in words 64-70 other than this field and the CompactFlash Storage Card does not support this field, the CompactFlash Storage Card shall return a value of zero in this field. Word 68: Minimum PIO transfer cycle time with IORDY Word 68 of the parameter information of the Identify Device command is defined as the minimum PIO transfer with IORDY flow control cycle time. This field defines, in nanoseconds, the minimum cycle time that the CompactFlash Storage Card supports while performing data transfers while utilizing IORDY flow control. If this field is supported, Bit 1 of word 53 shall be set to one. Any CompactFlash Storage Card that supports PIO mode 3 or above shall support this field, and the value in word 68 shall be the fastest defined PIO mode supported by the CompactFlash Storage Card. If bit 1 of word 53 is set to one because a CompactFlash Storage Card supports a field in words 64-70 other than this field and the CompactFlash Storage Card does not support this field, the CompactFlash Storage Card shall return a value of zero in this field. Words 82-84: Features/command sets supported Words 82, 83, and 84 shall indicate features/command sets supported. The value 0000h or FFFFh was placed in each of these words by CompactFlash Storage Cards prior to ATA-3 and shall be interpreted by the host as meaning that features/command sets supported are not indicated. Bits 1 through 13 of word 83 and bits 0 through 13 of word 84 are reserved. Bit 14 of word 83 and word 84 shall be set to one and bit 15 of word 83 and word 84 shall be cleared to zero to provide indication that the features/command sets supported words are valid. The values in these words should not be depended on by host implementers. Bit 0 of word 82 shall be set to zero; the SMART feature set is not supported. If bit 1 of word 82 is set to one, the Security Mode feature set is supported. Bit 2 of word 82 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 82 shall be set to one; the Power Management feature set is supported. Bit 4 of word 82 shall be set to zero; the Packet Command feature set is not supported. If bit 5 of word 82 is set to one, write cache is supported. If bit 6 of word 82 is set to one, look-ahead is supported. Bit 7 of word 82 shall be set to zero; release interrupt is not supported. Bit 8 of word 82 shall be set to zero; Service interrupt is not supported. Bit 9 of word 82 shall be set to zero; the Device Reset command is not supported. Bit 10 of word 82 shall be set to zero; the Host Protected Area feature set is not supported. Bit 11 of word 82 is obsolete. Bit 12 of word 82 shall be set to one; the CompactFlash Storage Card supports the Write Buffer command. Bit 13 of word 82 shall be set to one; the CompactFlash Storage Card supports the Read Buffer command. Bit 14 of word 82 shall be set to one; the CompactFlash Storage Card supports the NOP command. Bit 15 of word 82 is obsolete. Bit 0 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Download Microcode command. Bit 1 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA Queued and Write DMA Queued commands. Bit 2 of word 83 shall be set to one; the CompactFlash Storage Card supports the CFA feature set. If bit 3 of word 83 is set to one, the CompactFlash Storage Card supports the Advanced Power Management feature set. Bit 4 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Removable Media Status feature set. Words 85-87: Features/command sets enabled Words 85, 86, and 87 shall indicate features/command sets enabled. The value 0000h or FFFFh was placed in each of these words by CompactFlash Storage Cards prior to ATA-4 and shall be interpreted by the host as meaning that features/command sets enabled are not indicated. Bits 1 through 15 of word 86 are reserved. Bits 0-13 of word 87 are reserved. Bit 14 of word 87 shall be set to one and bit 15 of word 87 shall be cleared to zero to provide indication that the features/command sets enabled words are valid. The values in these words should not be depended on by host implementers. Transcend Information Inc. 54 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Bit 0 of word 85 shall be set to zero; the SMART feature set is not enabled. If bit 1 of word 85 is set to one, the Security Mode feature set has been enabled via the Security Set Password command. Bit 2 of word 85 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 85 shall be set to one; the Power Management feature set is supported. Bit 4 of word 85 shall be set to zero; the Packet Command feature set is not enabled. If bit 5 of word 85 is set to one, write cache is enabled. If bit 6 of word 85 is set to one, look-ahead is enabled. Bit 7 of word 85 shall be set to zero; release interrupt is not enabled. Bit 8 of word 85 shall be set to zero; Service interrupt is not enabled. Bit 9 of word 85 shall be set to zero; the Device Reset command is not supported. Bit 10 of word 85 shall be set to zero; the Host Protected Area feature set is not supported. Bit 11 of word 85 is obsolete. Bit 12 of word 85 shall be set to one; the CompactFlash Storage Card supports the Write Buffer command. Bit 13 of word 85 shall be set to one; the CompactFlash Storage Card supports the Read Buffer command. Bit 14 of word 85 shall be set to one; the CompactFlash Storage Card supports the NOP command. Bit 15 of word 85 is obsolete. Bit 0 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Download Microcode command. Bit 1 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA Queued and Write DMA Queued commands. If bit 2 of word 86 shall be set to one, the CompactFlash Storage Card supports the CFA feature set. If bit 3 of word 86 is set to one, the Advanced Power Management feature set has been enabled via the Set Features command. Bit 4 of word 86 shall be set to zero; the CompactFlash Storage Card does not support the Removable Media Status feature set. Word 89: Time required for Security erase unit completion Word 89 specifies the time required for the Security Erase Unit command to complete. This command shall be supported on CompactFlash Storage Cards that support security. Value Time 0 Value not specified 1-254 (Value * 2) minutes 255 >508 minutes Word 90: Time required for Enhanced security erase unit completion Word 90 specifies the time required for the Enhanced Security Erase Unit command to complete. This command shall be supported on CompactFlash Storage Cards that support security. Value Time 0 Value not specified 1-254 (Value * 2) minutes 255 >508 minutes Word 91: Advanced power management level value Bits 7-0 of word 91 contain the current Advanced Power Management level setting. Word 128: Security Status Bit 8: Security Level If set to 1, indicates that security mode is enabled and the security level is maximum. If set to 0 and security mode is enabled, indicates that the security level is high. Bit 5: Enhanced security erase unit feature supported If set to 1, indicates that the Enhanced security erase unit feature set is supported. Bit 4: Expire Transcend Information Inc. 55 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card If set to 1, indicates that the security count has expired and Security Unlock and Security Erase Unit are command aborted until a power-on reset or hard reset. Bit 3: Freeze If set to 1, indicates that the security is Frozen. Bit 2: Lock If set to 1, indicates that the security is locked. Bit 1: Enable/Disable If set to 1, indicates that the security is enabled. If set to 0, indicates that the security is disabled. Bit 0: Capability If set to 1, indicates that CompactFlash Storage Card supports security mode feature set. If set to 0, indicates that CompactFlash Storage Card does not support security mode feature set. Word 160: Power Requirement Description This word is required for CompactFlash Storage Cards that support power mode 1. Bit 15: VLD If set to 1, indicates that this word contains a valid power requirement description. If set to 0, indicates that this word does not contain a power requirement description. Bit 14: RSV This bit is reserved and shall be 0. Bit 13: -XP If set to 1, indicates that the CompactFlash Storage Card does not have Power Level 1 commands. If set to 0, indicates that the CompactFlash Storage Card has Power Level 1 commands Bit 12: -XE If set to 1, indicates that Power Level 1 commands are disabled. If set to 0, indicates that Power Level 1 commands are enabled. Bit 0-11: Maximum current This field contains the CompactFlash Storage Card’s maximum current in mA. Word 162: Key Management Schemes Supported Bit 0: CPRM support If set to 1, the device supports CPRM Scheme (Content Protection for Recordable Media) If set to 0, the device does not support CPRM. Bits 1-15 are reserved for future additional Key Management schemes. Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface. Notice! The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above impose significant restrictions on the implementation of the host: Additional Requirements for CF Advanced Timing Modes. There are four separate fields defined that describe support and selection of Advanced PIO timing modes and Advanced Multiword DMA timing modes. The older modes are reported in words 63 and 64. Word 63: Multiword DMA transfer and 6.2.1.6.19: Word 64: Advanced PIO transfer modes supported. Bits 2-0: Advanced True IDE PIO Mode Support Indicates the maximum True IDE PIO mode supported by the card. Value Maximum PIO mode timing selected 0 Specified in word 64 1 PIO Mode 5 2 PIO Mode 6 3-7 Reserved Bits 5-3: Advanced True IDE Multiword DMA Mode Support Indicates the maximum True IDE Multiword DMA Transcend Information Inc. 56 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card mode supported by the card. Value 0 1 2 3-7 Maximum Multiword DMA timing mode supported Specified in word 63 Multiword DMA Mode 3 Multiword DMA Mode 4 Reserved Bits 8-6: Advanced True IDE PIO Mode Selected Indicates the current True IDE PIO mode selected on the card. Value Current PIO timing mode selected 0 Specified in word 64 1 PIO Mode 5 2 PIO Mode 6 3-7 Reserved Bits 11-9: Advanced True IDE Multiword DMA Mode Selected Indicates the current True IDE Multiword DMA Mode Selected on the card. Value 0 1 2 3-7 Current Multiword DMA timing mode selected Specified in word 63 Multiword DMA Mode 3 Multiword DMA Mode 4 Reserved Bits 15-12 are reserved. Word 164: CF Advanced PCMCIA I/O and Memory Timing Modes Capabilities and Settings This word describes the capabilities and current settings for CFA defined advanced timing modes using the Memory and PCMCIA I/O interface. Notice! The use of PCMCIA I/O or Memory modes that are 100ns or faster impose significant restrictions on the implementation of the host: Additional Requirements for CF Advanced Timing Modes. Bits 2-0: Maximum Advanced PCMCIA I/O Mode Support Indicates the maximum I/O timing mode supported by the card. Value Maximum PCMCIA IO timing mode Supported 0 255ns Cycle PCMCIA I/O Mode 1 120ns Cycle PCMCIA I/O Mode 2 100ns Cycle PCMCIA I/O Mode 3 80ns Cycle PCMCIA I/O Mode 4-7 Reserved Bits 5-3: Maximum Memory timing mode supported Indicates the Maximum Memory timing mode supported by the card. Value Maximum Memory timing mode Supported 0 250ns Cycle Memory Mode 1 120ns Cycle Memory Mode 2 100ns Cycle Memory Mode 3 80ns Cycle Memory Mode 4-7 Reserved Bits 15-6 are reserved. Transcend Information Inc. 57 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.7 Idle - 97h or E3h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the automatic power down mode is enabled. If the sector count is zero, the automatic power down mode is disabled. Note that this time base (5 msec) is different from the ATA specification. Bit -> 7 6 5 4 Command (7) 3 2 1 0 97h or E3h C/D/H (6) X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Timer Count (5 msec increments) Feature (1) X 5.6.8 Idle Immediate - 95h or E1h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. Bit -> 7 6 5 4 Command (7) 3 2 1 0 95h or E1h C/D/H (6) X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X 5.6.9 Initialize Drive Parameters - 91h This command enables the host to set the number of sectors per track and the number of heads per cylinder. Only the Sector Count and the Card/Drive/Head registers are used by this command. Bit -> 7 6 5 4 Command (7) C/D/H (6) 3 2 0 91h X 0 X Drive Max Head (no. of heads-1) Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) Number of Sectors Feature (1) X Transcend Information Inc. 1 58 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.10 Read Buffer - E4h The Read Buffer command enables the host to read the current contents of the CompactFlash Storage Card’s sector buffer. This command has the same protocol as the Read Sector(s) command. Bit -> 7 6 5 4 2 1 0 E4h Command (7) C/D/H (6) 3 X Drive X Cyl High (5) X Cyl Low (4) X Sec Num (3) X Sec Cnt (2) X Feature (1) X 5.6.11 Read DMA – C8h This command uses DMA mode to read from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When this command is issued the CompactFlash Storage Card sets BSY, puts all or part of the sector of data in the buffer. The Card is then permitted, although not required, to set DRQ, clear BSY. The Card asserts DMAREQ while data is available to be transferred. The Card asserts DMAREQ while data is available to be transferred. The host then reads the (512 * sector-count) bytes of data from the Card using DMA. While DMAREQ is asserted by the Card, the Host asserts -DMACK while it is ready to transfer data by DMA and asserts -IORD once for each 16 bit word to be transferred to the Host. Interrupts are not generated on every sector, but upon completion of the transfer of the entire number of sectors to be transferred or upon the occurrence of an unrecoverable error. At command completion, the Command Block Registers contain the cylinder, head and sector number of the last sector read. If an error occurs, the read terminates at the sector where the error occurred. The Command Block Registers contain the cylinder, head, and sector number of the sector where the error occurred. The amount of data transferred is indeterminate. When a Read DMA command is received by the Card and 8 bit transfer mode has been enabled by the Set Features command, the Card shall return the Aborted error. Transcend Information Inc. 59 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.12 Read Multiple - C4h Note: This specification requires that CompactFlash Cards support a multiple block count of 1 and permits larger values to be supported. The Read Multiple command performs similarly to the Read Sectors command. Interrupts are not generated on every sector, but on the transfer of a block, which contains the number of sectors defined by a Set Multiple command. Command execution is identical to the Read Sectors operation except that the number of sectors defined by a Set Multiple command is transferred without intervening interrupts. DRQ qualification of the transfer is required only at the start of the data block, not on each sector. The block count of sectors to be transferred without intervening interrupts is programmed by the Set Multiple Mode command, which shall be executed prior to the Read Multiple command. When the Read Multiple command is issued, the Sector Count Register contains the number of sectors (not the number of blocks or the block count) requested. If the number of requested sectors is not evenly divisible by the block count, as many full blocks as possible are transferred, followed by a final, partial block transfer. The partial block transfer is for n sectors, where n = (sector count) modulo (block count). If the Read Multiple command is attempted before the Set Multiple Mode command has been executed or when Read Multiple commands are disabled, the Read Multiple operation is rejected with an Aborted Command error. Disk errors encountered during Read Multiple commands are posted at the beginning of the block or partial block transfer, but DRQ is still set and the data transfer shall take place as it normally would, including transfer of corrupted data, if any. Interrupts are generated when DRQ is set at the beginning of each block or partial block. The error reporting is the same as that on a Read Sector(s) Command. This command reads from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. At command completion, the Command Block Registers contain the cylinder, head and sector number of the last sector read. If an error occurs, the read terminates at the sector where the error occurred. The Command Block Registers contain the cylinder, head and sector number of the sector where the error occurred. The flawed data is pending in the sector buffer. Subsequent blocks or partial blocks are transferred only if the error was a correctable data error. All other errors cause the command to stop after transfer of the block that contained the error. Transcend Information Inc. 60 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.13 Read Sector(s) - 20h or 21h This command reads from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When this command is issued and after each sector of data (except the last one) has been read by the host, the CompactFlash Storage Card sets BSY, puts the sector of data in the buffer, sets DRQ, clears BSY, and generates an interrupt. The host then reads the 512 bytes of data from the buffer. At command completion, the Command Block Registers contain the cylinder, head and sector number of the last sector read. If an error occurs, the read terminates at the sector where the error occurred. The Command Block Registers contain the cylinder, head, and sector number of the sector where the error occurred. The flawed data is pending in the sector buffer. 5.6.14 Read Verify Sector(s) - 40h or 41h This command is identical to the Read Sectors command, except that DRQ is never set and no data is transferred to the host. When the command is accepted, the CompactFlash Storage Card sets BSY. When the requested sectors have been verified, the CompactFlash Storage Card clears BSY and generates an interrupt. Upon command completion, the Command Block Registers contain the cylinder, head, and sector number of the last sector verified. If an error occurs, the Read Verify Command terminates at the sector where the error occurs. The Command Block Registers contain the cylinder, head and sector number of the sector where the error occurred. The Sector Count Register contains the number of sectors not yet verified. Transcend Information Inc. 61 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.15 Recalibrate - 1Xh This command is effectively a NOP command to the CompactFlash Storage Card and is provided for compatibility purposes. 5.6.16 Request Sense - 03h This command requests extended error information for the previous command. Table defines the valid extended error codes for the CompactFlash Storage Card Series product. The extended error code is returned to the host in the Error Register. Transcend Information Inc. 62 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Table: Extended Error Codes 5.6.17 Seek - 7Xh This command is effectively a NOP command to the CompactFlash Storage Card although it does perform a range check of cylinder and head or LBA address and returns an error if the address is out of range. Transcend Information Inc. 63 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.18 Set Features – EFh This command is used by the host to establish or select certain features. If any subcommand input value is not supported or is invalid, the Compact Flash Storage Card shall return command aborted. Table: Feature Supported defines all features that are supported. Table: Feature Supported Transcend Information Inc. 64 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Features 01h and 81h are used to enable and clear 8 bit data transfer modes in True IDE Mode. If the 01h feature command is issued all data transfers shall occur on the low order D[7:0] data bus and the -IOIS16 signal shall not be asserted for data register accesses. The host shall not enable this feature for DMA transfers. Features 02h and 82h allow the host to enable or disable write cache in CompactFlash Storage Cards that implement write cache. When the subcommand disable write cache is issued, the CompactFlash Storage Card shall initiate the sequence to flush cache to non-volatile memory before command completion. Feature 03h allows the host to select the PIO or Multiword DMA transfer mode by specifying a value in the Sector Count register. The upper 5 bits define the type of transfer and the low order 3 bits encode the mode value. One PIO mode shall be selected at all times. For Cards which support DMA, one Multiword DMA mode shall be selected at all times. The host may change the selected modes by the Set Features command. Mode PIO default mode PIO default mode, disable IORDY PIO flow control transfer mode Reserved Multiword DMA mode Reserved Reserved Bits(7:3) 00000b 00000b 00001b 00010b 00100b 01000b 10000b Mode = transfer mode number Bits(2:0) 000b 001b Mode N/A Mode N/A N/A A CompactFlash Storage Card reporting support for Multiword DMA modes shall support all Multiword DMA modes below the highest mode supported. For example, if Multiword DMA mode 2 support is reported, then modes 1 and 0 shall also be supported. 5.6.19 Set Multiple Mode - C6h This command enables the CompactFlash Storage Card to perform Read and Write Multiple operations and establishes the block count for these commands. The Sector Count Register is loaded with the number of sectors per block. Upon receipt of the command, the CompactFlash Storage Card sets BSY to 1 and checks the Sector Count Register. If the Sector Count Register contains a valid value and the block count is supported, the value is loaded and execution is enabled for all subsequent Read Multiple and Write Multiple commands. If the block count is not supported, an Aborted Command error is posted and the Read Multiple and Write Multiple commands are disabled. If the Sector Count Register contains 0 when the command is issued, Read and Write Multiple commands are disabled. At power on, or after a hardware or (unless disabled by a Set Feature command) software reset, the default mode is Read and Write Multiple disabled. Transcend Information Inc. 65 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.20 Set Sleep Mode- 99h or E6h This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode, clear BSY and generate an interrupt. Recovery from sleep mode is accomplished by simply issuing another command (a reset is permitted but not required). Sleep mode is also entered when internal timers expire so the host does not need to issue this command except when it wishes to enter Sleep mode immediately. The default value for the timer is 5 milliseconds. Note that this time base (5 msec) is different from the ATA Specification. 5.6.21 Standby - 96h or E2h This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately. Recovery from sleep mode is accomplished by simply issuing another command (a reset is not required). Transcend Information Inc. 66 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.22 Standby Immediate - 94h or E0h This command causes the CompactFlash Storage Card to set BSY, enter the Sleep mode (which corresponds to the ATA “Standby” Mode), clear BSY and return the interrupt immediately. Recovery from sleep mode is accomplished by simply issuing another command (a reset is not required). 5.6.23 Translate Sector - 87h This command allows the host a method of determining the exact number of times a user sector has been erased and programmed. The controller responds with a 512 byte buffer of information containing the desired cylinder, head and sector, including its Logical Address, and the Hot Count, if available, for that sector. Table represents the information in the buffer. Please note that this command is unique to the CompactFlash Storage Card. Table:Translate Sector Information Transcend Information Inc. 67 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 5.6.24 Wear Level - F5h For the CompactFlash Storage Cards that do not support security mode feature set, this command is effectively a NOP command and only implemented for backward compatibility. The Sector Count Register shall always be returned with a 00h indicating Wear Level is not needed. If the CompactFlash Storage Card supports security mode feature set, this command shall be handled as Security Freeze Lock. 5.6.25 Write Buffer - E8h The Write Buffer command enables the host to overwrite contents of the CompactFlash Storage Card’s sector buffer with any data pattern desired. This command has the same protocol as the Write Sector(s) command and transfers 512 bytes. 5.6.26 Write DMA – CAh Transcend Information Inc. 68 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card This command uses DMA mode to write from 1 to 256 sectors as specified in the Sector Count register. A sector count of 0 requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When this command is issued the CompactFlash Storage Card sets BSY, puts all or part of the sector of data in the buffer. The Card is then permitted, although not required, to set DRQ, clear BSY. The Card asserts DMAREQ while data is available to be transferred. The host then writes the (512 * sector-count) bytes of data to the Card using DMA. While DMAREQ is asserted by the Card, the Host asserts -DMACK while it is ready to transfer data by DMA and asserts -IOWR once for each 16 bit word to be transferred from the Host. Interrupts are not generated on every sector, but upon completion of the transfer of the entire number of sectors to be transferred or upon the occurrence of an unrecoverable error. At command completion, the Command Block Registers contain the cylinder, head and sector number of the last sector read. If an error occurs, the read terminates at the sector where the error occurred. The Command Block Registers contain the cylinder, head, and sector number of the sector where the error occurred. The amount of data transferred is indeterminate. When a Write DMA command is received by the Card and 8 bit transfer mode has been enabled by the Set Features command, the Card shall return the Aborted error. 5.6.27 Write Multiple Command - C5h Note: This specification requires that CompactFlash Cards support a multiple block count of 1 and permits larger values to be supported. This command is similar to the Write Sectors command. The CompactFlash Storage Card sets BSY within 400 nsec of accepting the command. Interrupts are not presented on each sector but on the transfer of a block that contains the number of sectors defined by Set Multiple. Command execution is identical to the Write Sectors operation except that the number of sectors defined by the Set Multiple command is transferred without intervening interrupts. DRQ qualification of the transfer is required only at the start of the data block, not on each sector.The block count of sectors to be transferred without intervening interrupts is programmed by the Set Multiple Mode command, which shall be executed prior to the Write Multiple command. When the Write Multiple command is issued, the Sector Count Register contains the number of sectors (not the number of blocks or the block count) requested. If the number of requested sectors is not evenly divisible by the block count, as many full blocks as possible are transferred, followed by a final, partial block transfer. The partial block transfer is for n sectors, where: n = (sector count) modulo (block count). If the Write Multiple command is attempted before the Set Multiple Mode command has been executed or when Write Multiple commands are disabled, the Write Multiple operation shall be rejected with an aborted command error. Transcend Information Inc. 69 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Errors encountered during Write Multiple commands are posted after the attempted writes of theblock or partial block transferred. The Write command ends with the sector in error, even if it is in the middle of a block. Subsequent blocks are not transferred in the event of an error. Interrupts are generated when DRQ is set at the beginning of each block or partial block. The Command Block Registers contain the cylinder, head and sector numbers of the sector where the error occurred. The Sector Count Register contains the residual number of sectors that need to be transferred for successful completion of the command, e.g., each block has 4 sectors, a request for 8 sectors is issued and an error occurs on the third sector. The Sector Count Register contains 6 and the address is that of the third sector. 5.6.28 Write Multiple without Erase – CDh This command is similar to the Write Multiple command with the exception that an implied erase before write operation is not performed. The sectors should be pre-erased with the Erase Sector(s) command before this command is issued. 5.6.29 Write Sector(s) - 30h or 31h This command writes from 1 to 256 sectors as specified in the Sector Count Register. A sector count of zero requests 256 sectors. The transfer begins at the sector specified in the Sector Number Register. When this command is accepted, the CompactFlash Storage Card sets BSY, then sets DRQ and clears BSY, then waits for the host to fill the sector buffer with the data to be written. No interrupt is generated to start the first host transfer operation. No data should be transferred by the host until BSY has been cleared by the host. For multiple sectors, after the first sector of data is in the buffer, BSY shall be set and DRQ shall be cleared. After the next buffer is ready for data, BSY is cleared, DRQ is set and an interrupt is generated. When the final sector of data is transferred, BSY is set and DRQ is cleared. It shall remain in this state until the command is completed at which time BSY is cleared and an interrupt is generated. Transcend Information Inc. 70 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card If an error occurs during a write of more than one sector, writing terminates at the sector where the error occurs. The Command Block Registers contain the cylinder, head and sector number of the sector where the error occurred. The host may then read the command block to determine what error has occurred, and on which sector. 5.6.30 Write Sector(s) without Erase - 38h This command is similar to the Write Sector(s) command with the exception that an implied erase before write operation is not performed. This command has the same protocol as the Write Sector(s) command. The sectors should be pre-erased with the Erase Sector(s) command before this command is issued. If the sector is not pre-erased with the Erase Sector(s) command, a normal write sector operation will occur. 5.6.31 Write Verify - 3Ch This command is similar to the Write Sector(s) command, except each sector is verified immediately after being written. This command has the same protocol as the Write Sector(s) command. Transcend Information Inc. 71 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card Error Posting Command Error Register BBK UNC IDNF Check Power Mode Status Register ABRT AMNF V Execute Drive Diagnostic1 Erase Sector(s) DRDY DWF DSC V V V V V V V V Format Track CORR ERR V V V V V V V V V V V V V V Identify Device V V V V V Idle V V V V V Idle Immediate V V V V V V V V Initialize Drive Parameters V Read Buffer V V V V Read DMA V V V V V V V V V V Read Multiple V V V V V V V V V V Read Sector(s) V V V V V V V V V V Read Verify Sectors V V V V V V V V V V V V V V V Recalibrate V V Request Sense V V V V V V V Set Features V V V V V Set Multiple Mode V V V V V Set Sleep Mode V V V V V Stand By V V V V V Stand By Immediate V V V V V Seek V Translate Sector V Wear Level V V V V V V V V V V V V V V V V V V V V Write Buffer V Write DMA V V V V V V V V Write Multiple V V V V V V V V Write Multiple w/o Erase V V V V V V V V Write Sector(s) V V V V V V V V Write Sector(s) w/o Erase V V V V V V V V Write Verify V V V V V V V V V V V V Invalid Command Code V Error and Status Register summarizes the valid status and error value for all the CF-ATA Command set. Transcend Information Inc. 72 V1.1 TTS S3322M M~~11G GC CFF8800 80X CompactFlash Card 6.CIS Description: Address Data 7 6 5 4 3 2 000h 01h CISTPL_DEVICE 002h 004h 04h DFh TPL_LINK Link Device Type W 006h 79h 008h 1 0 Description of Contents CIS function Device Info tuple Tuple code length is 4 byte Type=D: I/O device WPS=1 : no WP switch Speed=7: extend bye Link to next tuple Device type, WPS speed Speed 79:80ns Speed 01h # Address units –1 unit size 2 Kbytes of address space Device size 00Ah FFh CISTPL_END End of CISTPL_DEVICE End marker 00Ch 1Ch CISTPL_DEVICE_OC Common memory other Tuple code Speed operating conditions tuple 00Eh 05h TPL_LINK Link 010h 02h Ext Reserved 3V M Length is 5 byte Link to next tuple 3V=1: dual voltage card, Other Conditions conditions for 3.3V operation Information M=0: conditions without wait 012h DFh Device Type W Speed Type=D: I/O device Device type, WPS WPS=1 : no WP switch speed Speed=7: extend bye 014h 79h Speed 79:80ns Speed 016h 01h # Address units –1 unit size 2 Kbytes of address space Device size 018h FFh CISTPL_END End of CISTPL_DEVICE_OC End marker 01Ah 18h CISTPL_JEDEC_C JEDEC programming info tuple Tuple code 01Ch 02h TPL_LINK Link length is 2 byte Link to next tuple 01Eh DFh JEDEC ID Device Mnufacturer ID Manufacturer ID 020h 01h JEDEC Info Manufacturer specific info Manufacturer info 022h 20h CISTPL_MANFID Manufacturer ID tuple Tuple code 024h 04h TPL_LINK Link Length is 4 bytes Link to next tuple 026h 0Ah TPLMID_MANF PC Card manufacturer code Manufacturer ID 028h 00h 02Ah 00h TPLMID_CARD Manufacturer specific info Manufacturer info 02Ch 00h 02Eh 15h CISTPL_VERS_1 Level 1 version/product info Tuple code Transcend Information Inc. 73 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 7 6 5 80X CompactFlash Card 4 3 2 1 0 Description of Contents CIS function 030h 1Bh CISTPL_LINK Link length is 27 bytes Link to next tuple 032h 04h TPPLV1_MAJOR PCMCIA2.0/JEIDA4.1 Major version 034h 01h TPPLV1_MINOR PCMCIA2.0/JEIDA4.1 Major version 036h 54h ‘T’ Info string 1 038h 52h ‘R’ 03Ah 41h ‘A’ 03Ch 4Eh ‘N’ 03Eh 53h ‘S’ 040h 43h ‘C’ 042h 45h ‘E’ 044h 4Eh ‘N’ 046h 44h ‘D’ 048h 20h ‘’ 04Ah 00h Null terminator 04Ch 54h… 064h 00h Null terminator 066h FFh End of CISTPL_VERS_1 End marker 068h 21h CISTPL_FUNCID Function ID tuple Tuple code 06Ah 02h CISTPL_LINK Link length is 2 bytes Link to next tuple 06Ch 04h TPLFID_FUNCTION Fixed disk drive Function code 06Eh 01h Reserved R=0: no expansion ROM System init byte P=1: configure at POST TPLFID_SYSINIT Transcend PRODUCT Name R P Info string 2 070h 22h CISTPL_FUNCE Function Extension tuple Tuple code 072h 02h CISTPL_LINK Link length is 2 bytes Link to next tuple 074h 01h Disk function extension tuple Disk interface information TPLFE_TYPE 076h 01h Disk interface type PC card ATA interface TPLFE_DATA 078h 22h CISTPL_FUNCE Function Extension tuple Tuple code 07Ah 03h CISTPL_LINK Link length is 3 bytes Link to next tuple 07Ch 02h Disk function extension tuple PC card ATA basic features TPLFE_TYPE Transcend Information Inc. 74 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 07Eh 0Ch 7 80X CompactFlash Card 6 5 Reserved 4 3 2 1 D U V S 0 Description of Contents D=0: single drive on card CIS function TPLFE_TYPE U=1: unique serial number S=1: silicon device V=00: no VPP required 080h 0Fh R I E N P I=0: twin IOIS16# unspecified TPLFE_TYPE E=0: index bit not emulated N=0: I/O includes 0x3F7 P=F(1111):low power, sleep, standby, idle supported 082h 1Ah CISTPL_CONFIG Configuration Tuple Tuple code 084h 05h TPL_LINK Link length is 5 bytes Link to next tuple 086h 01h RFS RMS RAS RFS: reserved Size of fields RMS: 1 byte register mask TPCC_SZ RAS: 2 bytes base address 088h 03h TPCC_LAST Last configuration entry is 03H Last entry index 08Ah 00h TPCC_RADR (LSB) Configuration registers are Configuration 08Ch 02h TPCC_RADR (MSB) Located at 0200H Register location 08Eh 0Fh TPCC_RMSK Configuration registers 0 to 3 Configuration register are present present mask 090h 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 092h 08h CISTPL_LINK Link length is 8 bytes Link to next tuple 094h C0h Memory mapped configuration, Configuration Table index=0 Index Byte I=1: Interface byte follows TPCE_INDX I D Configuration Index D=1: Default entry 096h C0h W R P B Interface type W=1: wait required Interface R=1: ready/busy active Description P=0: WP not used TPCE_IF B=0: BVD1, BVD2 not used Type=0: Memory interface Transcend Information Inc. 75 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 098h A1h 7 80X CompactFlash Card 6 5 M MS 4 3 2 1 0 IR IO T Power Description of Contents CIS function M=1: misc info present Feature Selection MS=1: 2 byte memory length Byte TPCE_FS IR=0: no interrupt is used IO=0: no I/O space is used T=0: no timing info specified Power=1: VCC info, no VPP 09Ah 01h R DI PI AI SI HV LV NV DI: no power-down current Power Description PI:no peak current info Structure Parameter AI: no average current info Selection Byte SI: no static current info TPCE_PD HV:no max voltage info LV:no min voltage info NV=1: nominal voltage info 09Ch 55h X Mantissa Exponent Nominal voltage 5.0V 09Eh 08h Length in 256 byte units (LSB) Length of memory space is 2 Memory space 0A0h 00h Length in 256 byte units (MSB) Kbyte descr. TPCE_MS 0A2h 20h X=0: no more misc fields Miscellaneous P=1: power-down supported features TPCE_MI X R P RO A T RO=0:read/write media A=0: audio not supported T=0: max twins is 0 0A4h 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 0A6h 06h CISTPL_LINK Link length is 6 bytes Link to next tuple 0A8h 00h Memory mapped configuration, TPCE_INDX I D Configuration Index index=0 0AAh 01h M MS IR IO T Power 0ACh 21h R DI PI AI SI HV LV NV Power=1: VCC info, no VPP TPCE_FS PI=1: peak current info TPCE_PD NV=1: nominal voltage info 0AEh B5h X Mantissa Exponent X=1: extension byte present 0B0h 1Eh X Extension Nominal voltage 3.30V 0B2h 4Dh X Mantissa Exponent Peak current 45 mA Transcend Information Inc. 76 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 7 80X CompactFlash Card 6 5 4 3 2 1 0 Description of Contents CIS function 0B4h 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 0B6h 0Ah CISTPL_LINK Link length is 10 bytes Link to next tuple 0B8h C1h I/O mapped, index=1 TPCE_INDX I D Configuration Index I=1: Interface byte follows D=1: Default entry 0BAh 41h W R P B Interface type W=0: wait not required TPCE_IF R=1: ready/busy active P=0: WP not used B=0: BVD1, BVD2 not used Type=1: I/O interface 0BCh 99h M MS IR IO T Power M=1: misc info present TPCE_FS MS=0: no memory space info IR=1: interrupt is used IO=1: I/O space is used T=0: no timing info specified Power=1: VCC info, no VPP 0BEh 01h R DI PI AI SI HV LV NV DI: no power-down current TPCE_PD PI: no peak current info AI: no average current info SI: no static current info HV:no max voltage info LV:no min voltage info NV=1: nominal voltage info 0C0h 55h 0C2h 64h X Mantissa Exponent R S E IO Nominal voltage 5.0V S =1: support 16 bit hosts TPCE_IO E =1: support 8 bit hosts IO=4: 4 address lines decoded Transcend Information Inc. 77 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 0C4h F0h 80X CompactFlash Card 7 6 5 4 3 2 1 0 S P M V I N S=1: interrupt sharing logic L B Description of Contents CIS function TPCE_IR P=1: pulse mode supported L=1: level mode supported M=1: masks V..N present V=0: no vendor unique IRQ B=0: no bus error IRQ I=0: no I/O check IRQ N=0: no NMI 0C6h FFh IRQ7..0 Interrupt signal may be 0C8h FFh IRQ15..8 Assigned to any host IRQ 0CAh 20h X R P RO A T X=0: no more misc fields TPCE_MI P=1: power-down supported RO=0:read/write media A=0: audio not supported T=0: max twins is 0 0CCh 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 0CEh 06h CISTPL_LINK Link length is 6 bytes Link to next tuple 0D0h 01h I I/O mapped, index=1 TPCE_INDX 0D2h 01h M MS IR IO T Power=1: VCC info, no VPP TPCE_FS 0D4h 21h R DI PI AI SI HV LV NV PI=1: peak current info TPCE_PD D Configuration Index Power NV=1: nominal voltage info 0D6h B5h X Mantissa Exponent X=1: extension byte present 0D8h 1Eh X Extension Nominal voltage 3.30V 0DAh 4Dh X Mantissa Exponent Peak current 45 mA 0DCh 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 0DEh 0Fh CISTPL_LINK Link length is 15 bytes Link to next tuple 0E0h C2h I/O mapped, index=2 TPCE_INDX I D Configuration Index I =1: Interface byte follows D=1: Default entry Transcend Information Inc. 78 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 0E2h 41h 7 80X CompactFlash Card 6 5 W R P 4 3 2 1 0 B Interface type Description of Contents W=0: wait not required CIS function TPCE_IF R=1: ready/busy active P=0: WP not used B=0: BVD1, BVD2 not used Type=1: I/O interface 0E4h 99h M MS IR IO T Power M=1: misc info present TPCE_FS MS=0: no memory space info IR=1: interrupt is used IO=1: I/O space is used T=0: no timing info specified Power=1: VCC info, no VPP 0E6h 01h R DI PI AI SI HV LV NV DI: no power-down current TPCE_PD PI:no peak current info AI: no average current info SI: no static current info HV:no max voltage info LV:no min voltage info NV=1: nominal voltage info 0E8h 55h 0EAh EAh X Mantissa Exponent R S E IO Nominal voltage 5.0V R=1: range follows TPCE_IO S=1: support 16 bit hosts E=1: support 8 bit hosts IO=10: 10 lines decoded 0ECh 61h LS AS NR LS=1: 1 byte length AS=2: 2 byte address NR=1: 2 address ranges 0EEh F0h Base address 1 (LSB) Address range 1 0F0h 01h Base address 1 (MSB) 0x1F0 to 0x1F7 0F2h 07h Address range 1 length 0F4h F6h Base address 2 (LSB) Address range 2 0F6h 03h Base address 2 (MSB) 0x3F6 to 0x3F7 0F8h 01h Address range 2 length Transcend Information Inc. 79 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 0FAh EEh 80X CompactFlash Card 7 6 5 4 S P M IRQN L 3 2 1 0 Description of Contents S=1: interrupt sharing logic CIS function TPCE_IR P=1: pulse mode supported L=1: level mode supported M=0: masks V..N not present IRQN=14: use interrupt 14 0FCh 20h X R P RO A T X=0: no more misc fields TPCE_MI P=1: power-down supported RO=0:read/write media A=0: audio not supported T=1: max twins is 0 0FEh 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 100h 06h CISTPL_LINK Link length is 6 bytes Link to next tuple 102h 02h I I/O mapped, index=2 TPCE_INDX 104h 01h M MS IR IO T Power=1: VCC info, no VPP TPCE_FS 106h 21h R DI PI AI SI HV LV NV PI=1: peak current info D Configuration Index Power TPCE_PD NV=1: nominal voltage info 108h B5h X Mantissa Exponent X=1: extension byte present 10Ah 1Eh X Extension Nominal voltage 3.30V 10Ch 4Dh X Mantissa Exponent Peak current 45 mA 10Eh 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 110h 0Fh CISTPL_LINK Link length is 15 bytes Link to next tuple 112h C3h I/O mapped, index=3 TPCE_INDX I D Configuration Index I=1: Interface byte follows D=1: Default entry 114h 41h W R P B Interface type W=0: wait not required TPCE_IF R=1: ready/busy active P=0: WP not used B=0: BVD1, BVD2 not used Type=1: I/O interface Transcend Information Inc. 80 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 116h 99h 7 80X CompactFlash Card 6 5 4 3 2 M MS IR IO T 1 0 Power Description of Contents M=1: misc info present CIS function TPCE_FS MS=0: no memory space info IR=1: interrupt is used IO=1: I/O space is used T=0: no timing info specified Power=1: VCC info, no VPP 118h 1h R DI PI AI SI HV LV NV DI: no power-down current TPCE_PD PI:no peak current info AI: no average current info SI: no static current info HV:no max voltage info LV:no min voltage info NV=1: nominal voltage info 11Ah 55h 11Ch EAh X Mantissa Exponent R S E IO Nominal voltage 5.0V R=1: range follows TPCE_IO S=1: support 16 bit hosts E=1: support 8 bit hosts IO=10: 10 lines decoded 11Eh 61h LS AS NR LS=1: 1 byte length AS=2: 2 byte address NR=1: 2 address ranges 120h 70h Base address 1 (LSB) Address range 1 122h 01h Base address 1 (MSB) 0x170 to 0x177 124h 07h Address range 1 length 126h 76h Base address 2 (LSB) Address range 2 128h 03h Base address 2 (MSB) 0x376 to 0x377 12Ah 01h Address range 2 length 12Ch EEh S P L M IRQN S=1: interrupt sharing logic TPCE_IR P=1: pulse mode supported L=1: level mode supported M=0: masks V..N not present IRQN=14: use interrupt 14 Transcend Information Inc. 81 V1.1 TTS S3322M M~~11G GC CFF8800 Address Data 12Eh 20h 80X CompactFlash Card 7 6 5 X R 4 3 2 1 P RO A T 0 Description of Contents X=0: no more misc fields CIS function TPCE_MI P=1: power-down supported RO=0:read/write media A=0: audio not supported T=0: max twins is 0 130h 1Bh CISTPL_CFTABLE_ENTRY Configuration tuple Tuple code 132h 06h CISTPL_LINK Link length is 6 bytes Link to next tuple 134h 03h I I/O mapped, index=3 TPCE_INDX 136h 01h M MS IR IO T Power Power=1: VCC info, no VPP TPCE_FS 138h 21h R DI PI AI SI HV LV NV PI=1: peak current info D Configuration Index TPCE_PD NV=1: nominal voltage info 13Ah B5h X Mantissa Exponent X=1: extension byte present 13Ch 1Eh X Extension Nominal voltage 3.30V 13Eh 4Dh X Mantissa Exponent Peak current 45 mA 140h 14h CISTPL_NO_LINK No link control tuple Tuple code 142h 00h CISTPL_LINK Link length is 0 bytes Link to next tuple 144h FFh End of CISTPL_VERS_1 End marker 146h FFh End of CIS Tuple code CISTPL_END Above technical information is based on industry standard data and tested to be reliable. However, Transcend makes no warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product. Transcend reserves the right to make changes in specifications at any time without prior notice. Transcend Information Inc. 82 V1.1