AAT AAT1110

Advanced Analog Technology, Inc.
AAT1110
Details are subject to change without notice
ONE-CHANNEL STEP-DOWN PWM CONTROLLER
Features
General Description
z
Under-Voltage Lockout (UVLO) Protection
z
Totem Pole Output
z
Output Short Circuit Protection
The AAT1110 is a one-channel step-down PWM
controller incorporating a soft-start function and a
short circuit protection (SCP) function.
z
Incorporates Soft-Start Function
z
Wide Operating Frequency:
10 kHz to 1MHz
z
Shutdown Control
z
Low Dissipation Current :
Typical 1.6mA in Operation
z
SOP-8 & TSSOP-8 Package Available
Each device consists of an on-chip voltage reference,
error amplifier, pulse width modulation controller,
under-voltage protection, soft-start, and short circuit
protection circuits. Switching frequencies up to
1MHz are set by an external resistor and capacitor.
Soft-start time can be implemented by the SCP
capacitor.
Additionally, a chip enabled feature is provided to
power down and reduce the supply current to 10 µA .
Pin Configuration
With an optimized number of external components,
the AAT1110 offers a simple and cost effective
solution.
VDD
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 1 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Pin Description
Pin No
1
2
3
4
5
6
7
8
Name
CE
SCP
VDD
OUT
GND
OSC
OE
IE
I/O
I
O
O
O
I
Description
Chip Enable Input Pin(Internal Pull "H")
Soft-Start and SCP Capacitor Connection Pin
Power Supply
Totem-Type Output Pin
Ground
Capacitor and Resistor Connection Pin for Setting the Oscillation Frequency
Error Amplifier Output Pin
Error Amplifier Inverting Input Pin
Absolute Maximum Ratings
Characteristics
Supply Voltage
Symbol
VDD
Value
7
Unit
V
Output Current
IO
− 120 /+120
mA
Operating Free-Air Temperature Range
TC
− 20 to +85
o
Tstorage
− 45 to +125
o
Pd
500
Storage Temperature Range
Power Dissipation
C
C
mW
Recommended Operating Conditions
Characteristics
Supply Voltage, VDD
Symbol
VDD
VI
C OSC
Min
2.6
0.5
Max
6.5
1.6
Unit
V
V
100
10,000
pF
OSC Resistor
R OSC
1.0
10.0
kΩ
Oscillator Frequency
f OSC
10
1,000
kHz
Output Current
IO
-
+30/ − 30
mA
Operating Free-Air Temperature
TC
− 20
+85
Error Amplifier Input Voltage
OSC Capacitor
o
C
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 2 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Electrical Characteristics, VDD = 3.3V (Unless Otherwise Specified) (See Note 1)
Oscillator
Parameter
f OSC
Oscillation Frequency
Frequency Variation With
Temperature
Frequency Input Stability
Lower Threshold Voltage
Hysteresis ( VUPH – VUPL )
f ∆V
VDD = 2.6V to 6.5V
VUPH
Test Condition
TC = 25 oC
VUPL
VHYS
Short Circuit Protection Control
Parameter
Max Unit
400
500
600
Min
kHz
5
%
1
%
Typ
Max Unit
2.12 2.47
2.85
V
1.96 2.28
2.63
V
o
0.19
TC = 25 C
V
TC =25 oC
Test Condition
Min
Typ
Max Unit
Vr1
1.160 1.262 1.360
V
Vtscd
1.160 1.262 1.360
V
I SCP
Charging Current
Typ
o
TC = 25 C
Note1: Typical values of all parameters are specified at
Input Threshold Voltage
Short-Circuit Detect
Threshold Voltage
Min
f ∆T
Under-Voltage Protection
Parameter
Upper Threshold Voltage
Test Condition
C OSC = 270pF,
R OSC = 4.2 kΩ
VSCP =0V
− 2.15
− 1.50 − 1.00 µA
Soft-Start
Parameter
I CS
Charging Current
Voltage at Soft-Start
Completion
Test Condition
VSCP =0V
Vts
Shutdown Control
Parameter
VSE
Shutdown Release Voltage
VSR
− 2.15
Typ
Max Unit
− 1.50 − 1.00 µA
1.160 1.262 1.360
Test Condition
Shutdown Enable Voltage
Min
Min
Typ
Max Unit
0.5
2.0
V
V
V
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 3 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Electrical Characteristics, VDD = 3.3V (Unless Otherwise Specified) (See Note 1)
EA (Error Amplifier)
Parameter
Input Threshold Voltage
VT Input Stability
VT Variation with
Temperature
Input Bias Current
Output Voltage Swing
VT
Test Condition
VOE = 0.7V
Min
Typ
Max Unit
VT∆V
VDD = 2.6 to 6.5V
-
2
8
mV
VT∆T
TC = − 20 oC to 90 oC
-
1
-
%
IB
-
0.1
1.0
µA
VOS+
1.4
1.7
-
VOS−
-
0.05
0.20
1.249 1.262 1.275
V
V
Output Sink Current
I OS+
VOE =0.7V
3
20
-
mA
Output Source Current
I OS−
VOE =0.7V
− 45
− 75
-
µA
Open-Loop Voltage Gain
A VO
70
85
-
dB
Min
Typ
1.9
2.3
-
V
Output Section
Parameter
High-Level Output Voltage
VOH
Test Condition
IO= − 30 mA
Low-Level Output Voltage
VOL
IO=+30mA
-
0.8
1.2
V
Rise Time
t RISE
CL=1,000pF
-
100
-
ns
Fall Time
t FALL
CL=1,000pF
-
100
-
ns
Min
Typ
-
1.3
-
mA
-
1.6
-
mA
Operating Current
Parameter
Supply Current
I DD−OFF
Test Condition
Output ”OFF” State
I DD−ON
RT =4.2 kΩ
Max Unit
Max Unit
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 4 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
How to Set the Time Constant for Soft-Start and Short Circuit Protection
1. Soft-Start
At power on, the AAT1110 operates in soft-start mode. The capacitor C SCP connected to SCP pin starts
charging at a constant current. In the soft-start mode, the voltage at SCP pin ( VSCP ) is input to the PWM
comparator, so that the ON duty of the OUT pin is controlled by the VSCP . At completion of the soft-start
operation, the voltage at the SCP pin stays low; the input from soft-start circuit to the PWM comparator
stays high, and enters the short circuit protection waiting state.
Soft-Start Time
t s (sec) ~ 0.84 × C SCP (µF)
2. Short Circuit Protection
If the switching regulator output suddenly drops due to loading effect, the error amplifier output will be
fixed at VOM + and capacitor C SCP will start charging. When the voltage at the SCP pin reaches
approximately 1.26V, the output pin will set low and SCP pin will remain low.
Once the protection circuit starts operating, the circuit can be recovered by setting the power supply.
Short Circuit Detection Time
t scp (sec) ~ 0.84 × C SCP (µF)
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 5 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Block Diagram
V DD
CE
C h ip E n a b le
GND
IREF
V REF
1 .2 6 V
SCP
C om p.
LA TCH
CE
S o ft-S tart
SCP
SCP
OSC
OSC
UVC
UVC
CE
UVLO
PW M
Com p.
V REF
1 .2 6 v
V DD
OE
V REF
CE
CE
V DD
V REF
1 .2 6 V
E rr-A m p
IE
OUT
UVC
CE
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 6 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Application Circuit Buck (Step-Down)
VDD
Cscp
VDD
VDD
VDD
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 7 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Buck (Step-Down) Timing Chart
1.262V
OE
Reference Input for Short Circuit
ldle Period Setting Voltage
Soft-Start Setting Voltage
OSC
Output
SCP
Soft-Start
Output
Short Circuit
Output Short
Circuit
tscp
ts
2.47V
Lockout Free
VDD
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 8 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Package Dimension
8-Pin SOP
θ
SYMBOLS
DIMENSIONS IN MILLIMETERS
DEMINSIONS IN INCHES
MIN
TYP
MAX
MIN
TYP
MAX
A
1.47
1.60
1.73
0.058
0.063
0.068
A1
0.10
---
0.22
0.004
---
0.008
A2
---
1.45
---
---
0.057
---
b
0.33
0.41
0.51
0.013
0.016
0.020
C
0.19
0.20
0.25
0.0075
0.008
0.0098
D
4.80
4.85
4.95
0.189
0.191
0.195
E
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
---
1.27
---
---
0.050
---
L
0.38
0.71
1.27
0.015
0.028
0.050
y
---
---
0.076
---
---
0
θ
0
---
0
0
---
0
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 9 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Tape and Reel
8-PinSOP
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 10 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Tape and Reel
8-Pin SOP (Cont.)
NOTE:
1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE ± 0.2 MILLIMETERS.
2. CAMBER NOT TO EXCEED 1 MILLIMETER IN 100 MILLIMETERS
3. MATERIAL: ANTI-STATIC BLACK ADVANTEK POLYSTYRENE.
4. A 0 AND B 0 ARE MEASURED ON A PLANE 0.3 MILLIMETERS ABOVE THE BOTTOM OF THE POCKET.
5.
K 0 IS MEASURED FROM A PLANE ON THE INSIDE BOTTOM OF THE POCKET TO THE TOP SURFACE OF
6.
THE CARRIER.
POCKET POSITION RELATIVE TO SPROCKET HOLE IS MEASURED AS TRUE POSITION OF POCKET, NOT
POCKET HOLE.
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 11 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Package Dimension
TSSOP-8
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 12 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Package Dimension
TSSOP-8
SYMBOL
A
A1
A2
b
C
D
E
E1
e
L
y
θ
DIMENSION IN MILLIMETERS
MIN
TYP
MAX
1.05
1.10
1.20
0.05
0.10
0.15
----1.00
1.05
0.25
----0.30
----0.127
----2.90
3.05
3.10
6.20
6.40
6.60
4.30
4.40
4.50
----0.65
----0.50
0.60
0.70
--------0.076
o
o
0
8o
4
DIMENSION IN INCHES
MIN
TYP
MAX
0.041
0.043
0.047
0.002
0.004
0.006
----0.039
0.041
0.010
----0.012
----0.005
----0.114
0.120
0.122
0.244
0.252
0.260
0.169
0.173
0.177
----0.026
----0.020
0.024
0.028
--------0.003
o
o
0
8o
4
NOTE:
1. CONTROLLING DIMENSION: MILLIMETERS.
2. LEAD FRAME MATERIAL: OLIN C7025/EFTEC 64T.
3. DIMENSION “D” DOES NOT INCLUDE MOLD FLASH, TIE BAR BURRS AND GATE BURRS. MOLD FLASH, TIE BAR BU
0.006” [0.15 MILLIMETERS] PER END. DIMENSION “E1” DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLA
MILLIMETERS] PER SIDE.
4. DIMENSION “b” DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.00
“b” DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS O
PROTRUSION AND AN ADJACENT LEAD TO BE 0.0028” [0.07 MILLIMETERS].
5. TOLERANCE: ± 0.010” [0.25 MILLIMETERES] UNLESS OTHERWISE SPECIFIED.
6. OTHERWISE DIMENSION FOLLOW ACCEPTABLE SPEC.
7. REFERENCE DOCUMENT: JEDEC SPEC MO-153.
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 13 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Tape and Reel
TSSOP-8
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 14 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Tape and Reel
TSSOP-8 (Cont.)
X.XXX X ± 0.0025
± 0.006
X.XXX
± 0.025
X.XX
± 0.10
X.X
± 0.25
X
UNIT: MILLIMETERS
NOTE:
1. 10 SPROCKET HOLE PITCH CUMULATIVE TOLERANCE ± 0.2 MILLIMETERS.
2. CHAMBER NOT TO EXCEED 1 MILLIMETER IN 100 MILLIMETERS.
3. MATERIAL: ANTI-STATIC BLACK ADVANTEK POLYSTYRENE.
4. A 0 AND B 0 ARE MEASURED ON A PLANE 0.3 MILLIMETERS ABOVE THE BOTTOM OF THE POCKET.
5. K 0 IS MEASURED FROM A PLANE ON THE INSIDE BOTTOM OF THE POCKET TO THE TOP SURFACE OF THE
CARRIER.
6. POCKET POSITION RELATIVE TO SPROCKET HOLE IS MEASURED AS TRUE POSITION OF POCKET, NOT
POCKET HOLE.
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 15 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Part Marking
SOP8 Top Marking
AAT1110
XXXXXX
SOP8 Back Marking
YYWW
Part Marking
TSSOP8 Top Marking
AAT1110
XXXXXX
TSSOP8 Back Marking
YYWW
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 16 of 17
V 1.0
Advanced Analog Technology, Inc.
AAT1110
Ordering Information
– 台灣類比科技股份有限公司 –
– Advanced Analog Technology, Inc. –
Page 17 of 17
V 1.0