[AK4344] AK4344 100dB 96kHz 24-Bit Stereo 3.3V ΔΣ DAC GENERAL DESCRIPTION The AK4344 is a 24bit low voltage & low power stereo. The AK4344 uses the Advanced Multi-Bit ΔΣ architecture, which achieves DR=100dB at 3.3V operation. The AK4344 integrates a combination of SCF and CTF filters increasing performance for systems with excessive clock jitter. The output voltage level can be set as high as 1Vrms. The AK4344 is offered in a space saving 16pin TSSOP package. FEATURES Sampling Rate: 8kHz ∼ 96kHz 24-Bit 8 times FIR Digital Filter SCF with high tolerance to clock jitter Single-ended output buffer Digital de-emphasis for 32kHz, 44.1kHz, 48kHz sampling I/F Format: 24-Bit MSB justified, 16/24-Bit LSB justified, I2S Compatible Master Clock: 512/768/1024/1536fs for Half Speed (8kHz ∼ 24kHz) 256/384/512/768fs for Normal Speed (8kHz ∼ 48kHz) 128/192/256/384fs for Double Speed (48kHz ∼ 96kHz) µP Interface: 4-wire/3-wire CMOS Input Level THD+N: -90dB(0dB) DR, S/N: 100dB DAC output voltage level: 1Vrms (@VDD=3.3V) Power Supply: 2.7 to 3.6V Ta = −20 ∼ 85°C 16pin TSSOP MS0641-E-00 2007/06 -1- [AK4344] MCLK CSN CCLK CDTI µP Interface VDD De-emphasis Control CDTO SDTI1 LRCK BICK Audio Data Interface TEST1 PDN Clock Divider VSS VCOM 8X Interpolator ΔΣ Modulator SCF LPF LOUT 8X Interpolator ΔΣ Modulator SCF LPF ROUT TEST2 Figure 1. AK4344 Block Diagram (Mode= “0”) MCLK CSN CCLK CDTI SDTI2 SDTI1 LRCK µP Interface VDD De-emphasis Control Audio Data Interface BICK TEST1 PDN Clock Divider VSS VCOM 8X Interpolator ΔΣ Modulator SCF LPF LOUT 8X Interpolator ΔΣ Modulator SCF LPF ROUT TEST2 Figure 2. AK4344 Block Diagram (Mode= “1”) MS0641-E-00 2007/06 -2- [AK4344] ■ Ordering Guide −20 ∼ +85°C 16pin TSSOP (0.65mm pitch) Evaluation Board for AK4344 AK4344ET AKD4344 ■ Pin Layout MCLK 1 16 TEST2 BICK 2 15 CDTO/ SDTI2 SDTI1 3 14 VDD LRCK 4 13 VSS PDN 5 12 VCOM CSN 6 11 LOUT CCLK 7 10 ROUT CDTI 8 9 TEST1 AK4344 Top View MS0641-E-00 2007/06 -3- [AK4344] PIN/FUNCTION No. 1 2 3 4 Pin Name MCLK BICK SDTI1 LRCK I/O I I I I 5 PDN I 6 7 8 CSN CCLK CDTI I I I 9 TEST1 I 10 11 ROUT LOUT O O 12 VCOM O 13 14 VSS VDD CDTO SDTI2 O I TEST2 O 15 16 Function Master Clock Input Pin Audio Serial Data Clock Pin Audio Serial Data Input Pin1 Input Channel Clock Pin Full Power Down Mode Pin “L” : Power down, “H” : Power up Chip Select Pin 0 Control Data Clock Pin Control Data Input Pin TEST Pin This pin must be connected to VSS. Rch Analog Output Pin, The output is “Hi-Z” when PDN pin = “L”. Lch Analog Output Pin, The output is “Hi-Z” when PDN pin = “L”. Common Voltage Output Pin, 0.5 × VDD Normally connected to VSS with a 4.7μF (min. 1μF, max. 10μF) electrolytic Capacitor. The output is “L” when PDN pin = “L” Ground Pin Power Supply Pin, 2.7 ∼ 3.6V Control Data Output Pin in serial mode, The output is “Hi-Z” when PDN pin = “L”. Audio Serial Data Input Pin2 TEST Pin This pin must be OPEN. Note: All digital input pins should not be left floating. MS0641-E-00 2007/06 -4- [AK4344] ABSOLUTE MAXIMUM RATINGS (VSS=0V; Note 1) Parameter Power Supply Input Current, Any Pin Except Supplies Digital Input Voltage Ambient Temperature (Powered applied) Storage Temperature (Note 2) Symbol VDD IIN VIND Ta Tstg min −0.3 −0.3 −20 −65 max 4.6 ±10 VDD+0.3 85 150 Units V mA V °C °C Note 1. All voltages with respect to ground. Note 2. MCLK, BICK, SDTI1, LRCK, PDN, CSN, CCLK, CDTI, SDTI2 WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (VSS=0V; Note 1) Parameter Power Supply Symbol VDD min 2.7 typ 3.3 max 3.6 Units V Note 1. All voltages with respect to ground. WARNING: AKEMD assumes no responsibility for the usage beyond the conditions in this datasheet. MS0641-E-00 2007/06 -5- [AK4344] ANALOG CHARACTERISTICS (Ta=25°C; VDD=3.3V; VSS=0V; fs=44.1kHz, 96kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Data; Measurement frequency=20Hz ∼ 20kHz at fs=44.1kHz, 20Hz ∼ 40kHz at fs=96kHz; unless otherwise specified) Parameter min typ max Units Dynamic Characteristics (GAIN bit= “1”) : Resolution 24 Bits 0dBFS -90 -80 dB THD+N fs=44.1kHz −60dBFS −37 dB BW=20kHz 0dBFS -88 dB fs=96kHz −60dBFS −34 dB BW=40kHz DR (−60dBFS with A-weighted) 92 100 dB S/N (A-weighted) 92 100 dB Interchannel Isolation 80 100 dB DC Accuracy: Interchannel Gain Mismatch 0.2 0.5 dB Gain Drift 100 ppm/°C Output Voltage: GAIN bit=“1” (Note 3) 2.60 2.8 3.00 Vpp Output Voltage: GAIN bit=“0” (Note 4) 2.05 2.2 2.35 Vpp Load Resistance (Note 5) 10 kΩ Load Capacitance 25 pF Power Supplies Power Supply Current Normal Operation (PDN pin = “H”, fs=44.1kHz) (Note 6) 7.0 mA Normal Operation (PDN pin = “H”, fs=96kHz) (Note 6) 8.5 12.8 mA Full Power-down mode (PDN pin = “L”) (Note 7) 10 50 μA Note 3. Full-scale voltage (0dB). Output voltage scales with the voltage of VDD, Vout = 0.85 × VDD (typ). Note 4. Full-scale voltage (0dB). Output voltage scales with the voltage of VDD, Vout = 0.67 × VDD (typ). Note 5. For AC-load. Note 6. RSTN bit= “1”, PW bit= “1” Note 7. All digital input pins are fixed to VDD or VSS. MS0641-E-00 2007/06 -6- [AK4344] FILTER CHARACTERISTICS (Ta=25°C; VDD=2.7 ∼ 3.6V; fs=44.1kHz; DEM1 bit= “0”, DEM0 bit= “1”) Parameter Symbol min DAC Digital Filter: Passband (Note 8) ±0.05dB PB 0 −6.0dB Stopband (Note 8) SB 24.1 Passband Ripple PR Stopband Attenuation SA 54 Group Delay (Note 9) GD Digital Filter + SCF + CTF: Frequency Response 0 ∼ 20kHz FR ∼ 40kHz (Note 10) - typ max Units 22.05 20.0 - 24.0 - kHz kHz kHz dB dB 1/fs ±0.1 ±0.2 - dB dB ±0.01 Note 8. The passband and stopband frequencies scale with fs (system sampling rate). Note 9. The calculating delay time which occurred by digital filtering. This time is from setting the 16/24bit data of both channels to input register to the output of analog signal. Note 10. At fs=96kHz. DC CHARACTERISTICS (Ta=25°C; VDD=2.7 ∼ 3.6V) Parameter Symbol min High-Level Input Voltage VIH 70%VDD Low-Level Input Voltage VIL High-Level Output Voltage (Iout=-80µA) VOH VDD-0.4 Low-Level Output Voltage (Iout=80µA) VOL Input Leakage Current Iin - MS0641-E-00 typ - max 30%VDD 0.4 ± 10 Units V V V V µA 2007/06 -7- [AK4344] SWITCHING CHARACTERISTICS (Ta=25°C; VDD=2.7 ∼ 3.6V; CL = 20pF) Parameter Symbol min Master Clock Frequency Half Speed Mode (512/768/1024/1536fs) fCLK 4.096 Normal Speed Mode (256/384/512/768fs) fCLK 2.048 Double Speed Mode (128/192/256/384fs) fCLK 6.144 Duty Cycle dCLK 40 LRCK Frequency Half Speed Mode (DFS1-0 = “10”) fsh 8 Normal Speed Mode (DFS1-0 = “00”) fsn 8 Double Speed Mode (DFS1-0 = “01”) fsd 48 Duty Cycle dCLK 45 Audio Interface Timing BICK Period 1/128fs tBCK Half Speed Mode 1/128fs tBCK Normal Speed Mode 1/64fs tBCK Double Speed Mode 70 tBCKL BICK Pulse Width Low 70 tBCKH Pulse Width High 40 tBLR BICK “↑” to LRCK Edge (Note 11) 40 tLRB LRCK Edge to BICK “↑” (Note 11) 40 tSDH SDTI Hold Time 40 tSDS SDTI Setup Time Control Interface Timing 200 CCLK Period tCCK 80 CCLK Pulse Width Low tCCKL 80 Pulse Width High tCCKH 40 CDTI Setup Time tCDS 40 CDTI Hold Time tCDH 150 CSN “H” Time tCSW 150 CSN “↓” to CCLK “↑” tCSS 50 tCSH CCLK “↑” to CSN “↑” tDCD CDTO Delay tCCZ CSN “↑” to CDTO Hi-Z Power-Down & Reset Timing PDN Pulse Width (Note 12) tPD 4 typ max Units 36.864 36.864 36.864 60 MHz MHz MHz % 24 48 96 55 kHz kHz kHz % ns ns ns ns ns ns ns ns ns 45 70 ns ns ns ns ns ns ns ns ns ns ms/μF Note 11. BICK rising edge must not occur at the same time as LRCK edge. Note 12. The AK4344 can be reset by bringing PDN pin = “L”. The PDN pulse width is proportional to the value of the capacitor (C) connected to VCOM pin. tPD = 4000× C. When C = 4.7μF, tPD is 19ms(min). The value of the capacitor (C) connected with VCOM pin should be 1μF ≤ C ≤ 10μF. When the states of DIF1-0 pins change, the AK4344 should be reset by PDN pin. MS0641-E-00 2007/06 -8- [AK4344] ■ Timing Diagram 1/fCLK VIH MCLK VIL tCLKH tCLKL dCLK=tCLKH x fCLK, tCLKL x fCLK 1/fs VIH LRCK VIL tBCK VIH BICK VIL tBCKH tBCKL Figure 3. Clock Timing VIH LRCK VIL tBLR tLRB VIH BICK VIL tSDH tSDS VIH SDTI VIL Figure 4. Serial Interface Timing MS0641-E-00 2007/06 -9- [AK4344] VIH CSN VIL tCSS tCCK tCCKL tCCKH VIH CCLK VIL tCDH tCDS CDTI C1 C0 A4 R/W VIH VIL Hi-Z CDTO Figure 5. WRITE/READ Command Input Timing in 3-wire/4-wire serial mode tCSW VIH CSN VIL tCSH VIH CCLK CDTI VIL D3 D2 D1 VIH D0 VIL Hi-Z CDTO Figure 6. WRITE Data Input Timing in 3-wire/4-wire serial mode VIH CSN VIL VIH CCLK VIL CDTI A1 VIH A0 VIL tDCD CDTO Hi-Z D7 D6 D5 50%VDD Figure 7. READ Data Output Timing 1 in 4-wire serial mode MS0641-E-00 2007/06 - 10 - [AK4344] tCSW VIH CSN VIL tCSH VIH CCLK VIL VIH CDTI VIL tCCZ CDTO D3 D2 D1 D0 Hi-Z 50%VDD Figure 8. READ Data Output Timing 2 in 4-wire serial mode tPD PDN VIL Figure 9. Power-Down & Reset Timing MS0641-E-00 2007/06 - 11 - [AK4344] OPERATION OVERVIEW ■ System Clock The external clocks, which are required to operate the AK4344, are MCLK, BICK and LRCK. The master clock (MCLK) should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. The MCLK frequency is detected from the relation between MCLK and LRCK automatically. The Half speed, the Normal speed and the Double speed mode are selected with the DFS1-0 bits (Table 1). The sampling speed mode is set depending on the MCLK frequency automatically for Auto mode (DFS1 bit = DFS0 bit = “1”) (Table 2). The AK4344 is automatically placed in the reset mode when MCLK stops in the normal operation mode (PDN pin = “H”), and the analog output becomes the VCOM voltage. After MCLK is input again, the AK4344 is powered up. After exiting reset by PDN pin at power-up etc., the AK4344 is in the reset mode until MCLK and LRCK are input. Mode Normal Speed Double Speed Half Speed Auto DFS1 0 0 1 1 DFS0 fs 0 8 ∼ 48kHz 1 48 ∼ 96kHz 0 8 ∼ 24kHz 1 8 ∼ 96kHz Table 1. System Clock Example MCLK Frequency 512/768fs 128/192/256/384fs 1024/1536fs Sampling Speed Mode Normal Speed Double Speed Half Speed Table 2. Auto Mode MCLK Frequency 256/384/512/768fs 128/192/256/384fs 512/768/1024/1536fs Table 2 Fs 8 ∼ 48kHz 48 ∼ 96kHz 8 ∼ 24kHz ■ Audio Interface Format The Data is shifted in via the SDTI pin using BICK and LRCK inputs. The DIF1-0 bits as shown in Table 3 can select four serial data modes. In all modes the serial data is MSB-first, 2’s compliment format and is latched on the rising edge of BICK. Mode 3 can be used for 16bit I2S Compatible format by zeroing the unused LSBs at BICK ≥ 48fs or BICK = 32fs. Mode 0 1 2 3 DIF1 0 0 1 1 DIF0 SDTI Format 0 16bit, LSB justified 1 24bit, LSB justified 0 24bit, MSB justified 1 16/24bit, I2S Compatible Table 3. Audio Interface Format MS0641-E-00 BICK ≥ 32fs ≥ 48fs ≥ 48fs ≥ 48fs or 32fs Figure Figure 10 Figure 11 Figure 12 Figure 13 2007/06 - 12 - [AK4344] LRCK 0 1 2 3 9 10 11 12 13 14 15 0 1 2 3 9 10 11 12 13 14 15 0 1 BICK(32fs) SDTI(i) 15 14 13 7 6 5 4 3 2 1 0 15 14 13 0 1 2 3 17 18 19 20 31 0 1 2 3 7 6 5 4 3 2 1 0 15 17 18 19 20 31 0 1 BICK(64fs) SDTI(i) Don't Care 15 14 13 12 1 0 Don't Care 15 14 13 12 2 1 0 SDTI-15:MSB, 0:LSB Lch Data Rch Data Figure 10. Mode 0 Timing LRCK 0 1 2 8 9 24 31 0 1 2 8 9 24 31 0 1 BICK(64fs) SDTI(i) Don't Care 23 1 0 8 Don't Care 8 23 1 0 23:MSB, 0:LSB Lch Data Rch Data Figure 11. Mode 1 Timing LRCK 0 1 2 20 21 22 23 24 31 0 1 2 20 21 22 23 24 31 0 1 BICK(64fs) SDTI(i) 23 22 4 3 2 1 0 Don't Care 23 22 4 3 2 1 0 Don't Care 23 23:MSB, 0:LSB Lch Data Rch Data Figure 12. Mode 2 Timing LRCK 0 1 2 3 21 22 23 24 25 0 1 2 21 22 23 24 25 0 1 BICK(64fs) SDTI(i) 23 22 4 3 2 1 0 Don't Care 23 22 4 3 2 1 0 Don't Care 23:MSB, 0:LSB Lch Data Rch Data Figure 13. Mode 3 Timing MS0641-E-00 2007/06 - 13 - [AK4344] ■ De-emphasis Filter A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15µs) and is controlled by DEM0 and DEM1. In case of double speed and quad speed mode, the digital de-emphasis filter is always off. DEM1 DEM0 Mode 0 0 1 1 0 1 0 1 44.1kHz OFF 48kHz 32kHz (default) Table 4. De-emphasis Filter Control (Normal Speed Mode) ■ Power-down The AK4344 is placed in the power-down mode by bringing PDN pin = “L”. and the digital filter is reset at the same time. This reset should always be done after power up. PDN Internal State (1) Normal Operation Power-down D/A In (Digital) “0” data GD (2) GD (3) (4) D/A Out (Analog) Clock In (2) (4) (5) Don’t care MCLK, BICK, LRCK External MUTE Normal Operation (6) Mute ON Notes: (1) PDN pin should be “L” for 19ms or more when an electrolytic capacitor 4.7μF is attached between VCOM pin and VSS. (2) The analog output corresponding to digital input has the group delay (GD). (3) When PDN pin = “L”, the analog output is Hi-Z. (4) Click noise occurs in 3 ∼ 4LRCK at both edges (↑ ↓) of PDN signal. This noise is output even if “0” data is input. (5) The external clocks (MCLK, BICK and LRCK) can be stopped in the power down mode (PDN pin = “L”). (6) Please mute the analog output externally if the click noise (4) influences system application. The timing example is shown in this figure. Figure 14. Power-down/up sequence example MS0641-E-00 2007/06 - 14 - [AK4344] ■ Reset Function (1) Reset by RSTN bit When RSTN bit =0, DAC is powered down but the internal register values are not initialized. The analog outputs go to VCOM voltage. Figure 15 shows the example of reset by RSTN bit. RSTN bit 3~4/fs (6) 2~3/fs (6) Internal RSTN bit Internal State Normal Operation P D/A In (Digital) d “0” data (1) D/A Out (Analog) Normal Operation Digital Block GD GD (3) (2) (3) (1) (4) Clock In Don’t care MCLK,LRCK,BICK Notes: (1) The analog output corresponding to digital input has the group delay (GD). (2) Analog outputs go to VCOM voltage (VDD/2). (3) Click noise occurs at the edges(“↑ ↓”) of the internal timing of RSTN bit. This noise is output even if “0” data is input. (4) The external clocks (MCLK, BICK and LRCK) can be stopped in the reset mode (RSTN bit = “0”). (5) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit “1” to the internal RSTN bit “1”. Figure 15. Reset Sequence Example1 MS0641-E-00 2007/06 - 15 - [AK4344] (2) RESET by MCLK stop (PDN pin = “H”) When MCLK stops, DAC is powered down but the internal register values are not initialized. The analog outputs go to VCOM voltage. PDN pin (1) Internal State Power-down D/A In (Digital) Power-down Normal Operation (2) GD (4) Hi-Z VCOM (2) (4) (4) Clock In (5) MCLK Stop MCLK, BICK, LRCK External MUTE Normal Operation (3) GD D/A Out (Analog) Reset (6) (6) (6) Notes: (1) PDN pin should be “L” for 19ms or more when an electrolytic capacitor 4.7μF is attached between VCOM pin and VSS. (2) The analog output corresponding to digital input has the group delay (GD). (3) The digital data can be stopped. The click noise after MCLK is input again by inputting the “0” data to this section can be reduced. (4) Click noise occurs in 3 ∼ 4LRCK at both edges (↑ ↓) of PDN signal, MCLK inputs and MCLK stops. This noise is output even if “0” data is input. (5) The external clocks (BICK and LRCK) can be stopped in the power down mode (MCLK stop). (6) Please mute the analog output externally if the click noise (4) influences system application. The timing example is shown in this figure. Figure 16. Reset Sequence Example 2 MS0641-E-00 2007/06 - 16 - [AK4344] ■ μP Control Interface The AK4344 can select 4-wire μP I/F mode (MODE bit = “0”) or 3-wire μP I/F mode (MODE bit = “1”). 1.4-wire μP I/F mode (MODE bit = “0”, default) The internal registers may be either written or read by the 4-wire μP interface pins: CSN, CCLK, CDTI and CDTO. The data on this interface consists of Chip address (2bits, C1/0; fixed to “01”), Read/Write (1bit), Register address (MSB first, 5bits) and Control data (MSB first, 8bits). Address and data are clocked in on the rising edge of CCLK and data is clocked out on the falling edge. For write operations, data is latched after the 16th rising edge of CCLK, after a high-to-low transition of CSN. CSN should be set to “H” once after 16 CCLKs. For read operations, the CDTO output goes high impedance after a low-to-high transition of CSN. The maximum speed of CCLK is 5MHz. PDN pin = “L” resets the registers to their default values. CSN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CCLK CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 WRITE Hi-Z CDTO CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 READ CDTO Hi-Z D7 D6 D5 D4 D3 D2 D1 D0 Hi-Z C1-C0: Chip Address: (Fixed to “01”) R/W: READ/WRITE (0:READ, 1:WRITE) A4-A0: Register Address D7-D0: Control Data Figure 17. 4-wire Serial Control I/F Timing *When the AK4344 is in the power down mode (PDN pin = “L”) or the MCLK is not provided, writing into the control register is inhibited. MS0641-E-00 2007/06 - 17 - [AK4344] 2.3-wire μP I/F mode (MODE bit = “1”) Internal registers may be written by 3-wire µP interface pins, CSN, CCLK and CDTI. The data on this interface consists of Chip Address (2bits, C1/0; fixed to “01”), Read/Write (1bit; fixed to “1”, Write only), Register Address (MSB first, 5bits) and Control Data (MSB first, 8bits). AK4344 latches the data on the rising edge of CCLK, so data should clocked in on the falling edge. The writing of data becomes valid by 16th CCLK after a high to low transition of CSN. CSN should be set to “H” once after 16 CCLKs for each address. The clock speed of CCLK is 5MHz (max). PDN pin = “L” resets the registers to their default values. The internal timing circuit is reset by RSTN bit, but the registers are not initialized. CSN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CCLK CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 C1-C0: R/W: A4-A0: D7-D0: Chip Address (Fixed to “01”) READ/WRITE (Fixed to “1”, Write only) Register Address Control Data Figure 18. Control I/F Timing *The AK4344 does not support the read command and chip address. C1/0 and R/W are fixed to “011” *When the AK4344 is in the power down mode (PDN pin = “L”) or the MCLK is not provided, writing into the control register is inhibited. ■ DAC input select The AK4344 can select 4-wire μP I/F mode (MODE bit = “0”) or 3-wire μP I/F mode (MODE bit = “1”). In 3-wire μP I/F mode, the AK4344 can select the input data of DAC from SDTI1 or SDTI2 data. MODE 0 1 1 μP / IF 4-wire 3-wire 3-wire SEL x 0 1 DAC input SDTI1 SDTI1 SDTI2 (x: Don’t care) Table 5. DAC Input MS0641-E-00 2007/06 - 18 - [AK4344] ■ Register Map Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0 00H Control 1 1 0 0 0 DIF1 DIF0 PW RSTN 01H 02H Control 2 Control 3 0 0 1 0 0 0 DFS1 INVL DFS0 INVR DEM1 MODE DEM0 0 GAIN SEL Notes: For addresses from 03H to 1FH, data must not be written. When PDN pin goes “L”, the registers are initialized to their default values. When RSTN bit goes “0”, the only internal timing is reset and the registers are not initialized to their default values. All data can be written to the register even if PW or RSTN bit is “0”. The bits shown as “0” should be written “0” and the bits shown as “1” should be written “1”. ■ Register Definitions Addr 00H Register Name Control 1 D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 0 DIF1 DIF0 PW RSTN 1 1 1 1 R/W Default R/W 1 0 0 0 RSTN: Internal timing reset control 0: Reset. All registers are not initialized. 1: Normal Operation When MCLK frequency or DFS changes the click noise occurs. It can be reduced by RSTN bit. PW: Power down control 0: Power down. All registers are not initialized. 1: Normal Operation DIF1-0: Audio data interface formats (Table 3) Initial: “11”, Mode 3 MS0641-E-00 2007/06 - 19 - [AK4344] Addr 01H Register Name Control 2 D7 D6 D5 D4 D3 D2 D1 D0 0 1 0 DFS1 DFS0 DEM1 DEM0 GAIN 1 0 1 1 R/W Default R/W 0 1 0 1 DEM1-0: De-emphasis Response (Table 4) Initial: “01”, OFF DFS1-0: Sampling speed control 00: Normal speed 01: Double speed 10: Half speed 11: Auto (default) When changing between Normal/Double Speed Mode and Half Speed Mode, some click noises occur. GAIN: Output Voltage scale 0: Vout = 0.67 × VDD (typ) at Full-scale voltage(0dB). 1: Vout = 0.85 × VDD (typ) at Full-scale voltage(0dB). Register Name 02H Control 3 D7 D6 D5 D4 0 0 0 INVL R/W Default D3 D2 D1 D0 INVR MODE 0 SEL 0 0 0 0 R/W 0 0 0 0 INVR: Inverting Lch Output Polarity 0: Normal Output 1: Inverted Output INVL: Inverting Rch Output Polarity 0: Normal Output 1: Inverted Output MODE: Mode Control 0: 4 wire mode 1: 3 wire mode SEL: DAC input 0: SDTI1 input 1: SDTI2 input SEL bit is disabled in 4-wire uP I/F mode (MODE bit = “0”). MS0641-E-00 2007/06 - 20 - [AK4344] SYSTEM DESIGN Figure 19 and Figure 20 shows the system connection diagram. The evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. Master Clock 1 MCLK TEST2 64fs 2 BICK CDTO 15 24bit Audio Data 3 SDTI VDD 14 fs Reset & Power down Micro Controller Digital Ground 16 0.1u 4 LRCK 5 + 10u VSS 13 PDN VCOM 12 6 CSN LOUT 11 Lch Out 7 CCLK ROUT 10 Rch Out 8 CDTI TEST1 9 AK4344 4.7u Analog Supply 2.7 to 3.6V + Analog Ground Figure 19. Typical Connection Diagram (Mode bit = “0”, 4 wire mode ) 24bit Audio Data2 Master Clock 1 MCLK TEST2 16 64fs 2 BICK SDTI2 15 3 SDTI VDD 14 24bit Audio Data1 fs Reset & Power down Micro Controller Digital Ground 0.1u 4 LRCK 5 PDN 6 7 8 + 10u VSS 13 VCOM 12 CSN LOUT 11 Lch Out CCLK ROUT 10 Rch Out CDTI TEST1 9 AK4344 4.7u Analog Supply 2.7 to 3.6V + Analog Ground Figure 20. Typical Connection Diagram (Mode bit = “1”, 3 wire mode ) MS0641-E-00 2007/06 - 21 - [AK4344] 1. Grounding and Power Supply Decoupling The AK4344 requires careful attention for power supply and grounding arrangements. VDD is usually supplied from the analog supply in the system. System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling capacitors should be as near to the AK4344 as possible, with the small value ceramic capacitor being the closest. 2. Voltage Reference The differential Voltage between VDD and VSS sets the analog output range. VCOM is used as a common voltage of the analog signal. VCOM pin is a signal ground of this chip. An electrolytic capacitor about 4.7μF should be attached between VCOM pin and VSS. No load current may be drawn from VCOM pin. Especially, the ceramic capacitor should be connected to this pin as near as possible. 3. Analog Outputs The analog outputs are single-ended and centered around the VCOM voltage (0.5 × VDD). The output signal range is typically 2.8Vpp (typ@VDD=3.3V). The internal switched-capacitor filter and continuous-time filter attenuate the noise generated by the delta-sigma modulator beyond the audio passband. The output voltage is a positive full scale for 7FFFFFH (@24bit) and a negative full scale for 800000H (@24bit). The ideal output is VCOM voltage (0.5 × VDD) for 000000H (@24bit). DC offsets on analog outputs are eliminated by AC coupling since analog outputs have DC offsets of VCOM + a few mV. Figure 21 shows an example of the external LPF with 2.8Vpp (1Vrms) output. AK4344 10u 220 Analog Out LOUT / ROUT 2.8Vpp (1Vrms) 22k 1nF fc=723.4kHz, g=-0.013dB at 40kHz st Figure 21. External 1 order LPF Circuit Example MS0641-E-00 2007/06 - 22 - [AK4344] PACKAGE 16pin TSSOP (Unit: mm) *5.0±0.1 9 A 8 1 0.13 M 6.4±0.2 *4.4±0.1 16 1.05±0.05 0.22±0.1 0.65 0.17±0.05 Detail A 0.5±0.2 0.1±0.1 Seating Plane 0.10 NOTE: Dimension "*" does not include mold flash. 0-10° ■ Package & Lead frame material Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy Cu Solder (Pb free) plate MS0641-E-00 2007/06 - 23 - [AK4344] MARKING AKM 4344ET XXYYY 1) 2) 3) 4) Pin #1 indication Date Code : XXYYY (5 digits) XX: Lot# YYY: Date Code Marketing Code : 4344ET Asahi Kasei Logo REVISION HISTORY Date (YY/MM/DD) 07/06/20 Revision 00 Reason First Edition Page Contents IMPORTANT NOTICE z These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei EMD Corporation (AKEMD) or authorized distributors as to current status of the products. z AKEMD assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of any information contained herein. z Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. z AKEMD products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKEMD assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKEMD. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z It is the responsibility of the buyer or distributor of AKEMD products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKEMD harmless from any and all claims arising from the use of said product in the absence of such notification. MS0641-E-00 2007/06 - 24 -