ASAHI KASEI [AKD5358-B] AKD5358-B AK5358 Evaluation Board Rev.0 GENERAL DESCRIPTION AKD5358-B is an evaluation board for the digital audio 24bit 96kHz A/D converter, AK5358. AKD5358-B has analog input circuits and a digital interface transmitter,and can achieve the interface with digital audio systems via opt-connector. Ordering guide AKD5358-B --- AK5358 Evaluation Board FUNCTION • DIT (AK4114) with optical output VA,VD AGND,DGND LIN RIN AK4114 (DIT) AK5358 Opt Out DSP Data 10pin Header Figure 1. AKD5358-B Block Diagram * Circuit diagram and PCB layout are attached at the end of this manual. <KM079501> 2005/09 -1- ASAHI KASEI [AKD5358-B] 1. Evaluation Board Manual Operation sequence 1) Set up the power supply lines. [VA] (red) = 2.7 ∼ 5.5V or +15V [VD] (orange) = 2.7 ∼ 5.5V [VCC] (red) = 3.3V [AGND] (black) = 0V [DGND] (black) = 0V : for VA of AK5358 (typ. 5.0V) : for VD of AK5358, 74HC14 (typ. 5.0V) : for AK4114 : for analog ground : for logic ground Each supply line should be distributed from the power supply unit. 2) Set up the evaluation mode, jumper pins and DIP switches. (See the followings.) 3) Power on. The AK5358 and AK4114 should be reset once bringing SW2 = “L” upon power-up. Evaluation mode (1) Slave Mode (1-1) A/D evaluation using DIT function of AK4114 PORT2 (DIT) is used. DIT generates audio bi-phase signal from received data and which is output through optical connector (TOTX141). It is possible to connect AKM’s D/A converter evaluation boards on the digital-amplifier, which equips DIR input. Nothing should be connected to PORT1 (DSP). JP5 MCLK (1-2) All interface signals including master clock are fed externally. PORT1 (DSP) is used. All interface signals (MCLK, SCLK, LRCK) are provided to the AK5358 through PORT1. JP5 (MCLK) should be open. The DIF1 of SW1 (MODE) should be set to “H”. JP5 MCLK <KM079501> 2005/09 -2- ASAHI KASEI [AKD5358-B] (2) Master Mode (2-1) A/D evaluation using DIT function of AK4114 PORT2 (DIT) is used. DIT generates audio bi-phase signal from received data and which is output through optical connector (TOTX141). It is possible to connect AKM’s D/A converter evaluation boards on the digital-amplifier, which equips DIR input. Nothing should be connected to PORT1 (DSP). The DIF1 of SW1 (MODE) should be set to “H”. JP5 MCLK (2-2) Master clock is fed externally. PORT1 (DSP) is used. MCLK is provided to the AK5358 through PORT1. JP5 (MCLK) should be open. The DIF1 of SW1 (MODE) should be set to “H”. JP5 MCLK Other jumper pins set up 1. JP1 (GND) : Analog ground and Digital ground OPEN : Separated. SHORT : Common. (The connector “DGND” can be open.) <Default> 2. JP2 (CKS1) : Setting of CKS1 pin for AK5358 H : Master mode L : Slave mode <Default> 3. JP3 (VA) : Select VA for AK5358 VA : Supply from VA connector <Default> REG : Supply from regulator. VA connector should be supplied +15V. 4. JP4 (VD) : Select VD for AK5358 VA : Supply from VA connector VD : Supply from VD connector <Default> <KM079501> 2005/09 -3- ASAHI KASEI [AKD5358-B] DIP Switch set up [SW1] (MODE1): Setting the evaluation mode for AK5358 and AK4114 ON is “H”, OFF is “L”. CKS1 should be set by JP2. No. 1 2 3 4 Name CKS0 CKS2 DIF DIF1 OFF (“L”) ON (“H”) See Table 2 MSB justified AK4114 Master mode Table 1. Mode Setting Mode CKS2 CKS1 CKS0 Input Level Master/Slave 0 L L L CMOS Slave 1 2 3 L L L L H H H L H CMOS CMOS Master Master 4 H L L TTL Slave 5 6 7 H H H L H H H L H CMOS CMOS Master Master I2S Compatible AK4114 Slave mode MCLK 256/384fs (8k≤fs≤96k) 512/768fs (8k≤fs≤48k) Reserved 256fs (8k≤fs≤96k) 512fs (8k≤fs≤48k) 256/384fs (∼ 96kHz) 512/768fs (∼ 48kHz) Reserved 384fs (8k≤fs≤96k) 768fs (8k≤fs≤48k) SCLK ≥ 48fs or 32fs 64fs 64fs ≥ 48fs or 32fs 64fs 64fs Table 2. Mode Setting of AK5358 Note: AK4114 does not support MCLK=384fs/512fs/768fs. PORT1 (DSP) should be used when MCLK=384fs/512fs/768fs. The function of the toggle SW Upper-side is “H” and lower-side is “L”. [SW2] (PDN): Resets the AK5358 and AK4114. Keep “H” during normal operation. <KM079501> 2005/09 -4- ASAHI KASEI [AKD5358-B] Analog Input Circuits Analog signal is input via J1(RIN) and J2(LIN) of RCA connectors. J1 RIN C1 10u + AINR J2 LIN C2 10u + AINL Figure 2. Analog Input circuits * AKM assumes no responsibility for the trouble when using the circuit examples. <KM079501> 2005/09 -5- ASAHI KASEI [AKD5358-B] MEASUREMENT RESULTS [Measurement condition] • Measurement unit • MCLK • SCLK • fs • Bit • Power Supply • Interface • Temperature : Audio Precision, System Two Cascade : 256fs : 64fs : 48kHz, 96kHz : 24bit : VA = VD = 5.0V (Using regulator) : DIT : Room Parameter ADC Analog Input Characteristics: fs=48kHz S/(N+D) (−1dB Input) fs=96kHz fs=48kHz, A-weighted D-Range (−60dB Input) fs=96kHz S/N fs=48kHz, A-weighted fs=96kHz <KM079501> Result (Lch / Rch) Unit 91.9 / 91.4 90.5 / 89.8 102.6 / 102.3 99.3 / 99.4 102.8 /102.9 99.5 / 99.5 dB dB dB dB dB dB 2005/09 -6- ASAHI KASEI [AKD5358-B] [ADC Plot : fs=48kHz] AK5358 THD+N vs. Input Level VA=15V, VD=5V, fs=48kHz, fin=1kHz -70 -75 -80 -85 -90 d B F S -95 -100 -105 -110 -115 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dBr Figure 1. THD+N vs. Input Level AK5358 THD+N vs. Input Frequency VA=15V, VD=5V, fs=48kHz, Input=-1dBr -70 -75 -80 -85 -90 d B F S -95 -100 -105 -110 -115 -120 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 2. THD+N vs. Input Frequency <KM079501> 2005/09 -7- ASAHI KASEI [AKD5358-B] AKD5358 Linearity VA=15V, VD=5V, fs=48kHz, fin=1kHz +0 -10 -20 -30 -40 -50 d B F S -60 -70 -80 -90 -100 -110 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dBr Figure 3. Linearity AK5358 Frequency Response VA=15V, VD=5V, fs=48kHz Input = -1dBr -0.5 -0.6 -0.7 -0.8 -0.9 d B F S -1 -1.1 -1.2 -1.3 -1.4 -1.5 20 50 100 200 500 1k 2k 5k 10k 20k Hz Figure 4. Frequency Response <KM079501> 2005/09 -8- ASAHI KASEI [AKD5358-B] AKD5358 Crosstalk VA=15V, VD=5V, fs=48kHz, Input=-1dBr -70 -75 -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 -145 -150 20 50 100 200 500 1k 2k 5k 10k 20k 5k 10k 20k Hz Figure 5. Crosstalk AK5358 FFT Plot VA=15V, VD=5V, fs=48kHz, Input=-1dBr, fin=1kHz +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k 2k Hz Figure 6. FFT Plot <KM079501> 2005/09 -9- ASAHI KASEI [AKD5358-B] AK5358 FFT Plot VA=15V, VD=5V, fs=48kHz, Input=-60dBr, fin=1kHz +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k 2k 5k 10k 20k 2k 5k 10k 20k Hz Figure 7. FFT Plot AK5358 FFT Plot VA=15V, VD=5V, fs=48kHz, fin=None +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k Hz Figure 8. FFT Plot <KM079501> 2005/09 - 10 - ASAHI KASEI [AKD5358-B] [ADC Plot : fs=96kHz] AK5358 THD+N vs. Input Level VA=15V, VD=5V, fs=96kHz, fin=1kHz -70 -75 -80 -85 -90 d B F S -95 -100 -105 -110 -115 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dBr Figure 9. THD+N vs. Input Level AKD5358 THD+N vs. Input Frequency VA=15V, VD=5V, fs=96kHz, Input=-1dBr -70 -72.5 -75 -77.5 -80 -82.5 -85 -87.5 -90 d B F S -92.5 -95 -97.5 -100 -102.5 -105 -107.5 -110 -112.5 -115 -117.5 -120 20 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 10. THD+N vs. Input Frequency <KM079501> 2005/09 - 11 - ASAHI KASEI [AKD5358-B] AKD5358 Linearity VA=15V, VD=5V, fs=96kHz, fin=1kHz +0 -10 -20 -30 -40 -50 d B F S -60 -70 -80 -90 -100 -110 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 +0 dBr Figure 11. Linearity AK5358 Frequency Response VA=15V, VD=5V, fs=96kHz Input=-1dBr -0.5 -0.6 -0.7 -0.8 -0.9 d B F S -1 -1.1 -1.2 -1.3 -1.4 -1.5 20 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 12. Frequency Response <KM079501> 2005/09 - 12 - ASAHI KASEI [AKD5358-B] AKD5358 Crosstalk VA=15V, VD=5V, fs=96kHz, Input=-1dBr -70 -75 -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 -145 -150 20 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 13. Crosstalk AK5858 FFT Plot VA=15V, VD=5V, fs=96kHz, Input=-1dBr, fin=1kHz +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k 2k 5k 10k 20k 40k Hz Figure 14. FFT Plot <KM079501> 2005/09 - 13 - ASAHI KASEI [AKD5358-B] AK5858 FFT Plot VA=15V, VD=5V, fs=96kHz, Input=-60dBr, fin=1kHz +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k 2k 5k 10k 20k 40k 5k 10k 20k 40k Hz Figure 15. FFT Plot AK5858 FFT Plot VA=15V, VD=5V, fs=96kHz, fin=None +0 -10 -20 -30 -40 -50 -60 -70 d B F S -80 -90 -100 -110 -120 -130 -140 -150 -160 -170 -180 20 50 100 200 500 1k 2k Hz Figure 16. FFT Plot <KM079501> 2005/09 - 14 - ASAHI KASEI [AKD5358-B] Revision History Date (YY/MM/DD) 05/06/29 Manual Revision KM079500 05/09/01 KM079501 Board Reason Revision 0 First Edition 0 Graph addition Contents P7-14 IMPORTANT NOTICE • These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. • AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. • Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. • AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. • It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. <KM079501> 2005/09 - 15 - A B C E DGND J1 RIN JP1 GND D E E AGND C1 10u + VD SW1 1 2 3 4 U1 J2 LIN C2 10u 8 7 6 5 CKS0 CKS2 DIF DIF1 RP1 MODE + 1 AINR CKS0 16 2 AINL CKS2 15 3 CKS1 DIF 14 4 VCOM PDN 13 5 AGND SCLK 12 4 3 2 1 D DIF1 D 47k L JP2 CKS1 T1 NJM78M05FA + C7 0.1u OUT JP3 REG H C3 2.2u REG 3 REG + C8 47u C5 10u C9 0.1u + C4 NC C6 0.1u 6 R3 5.1 2 C10 47u IN 2 1 1 GND VA + VA 7 C C11 10u MCLK VD LRCK VA DGND JP4 VD SDTO 51 R2 51 R4 51 R5 51 SCLK 11 MCLK 10 + C12 0.1u 8 R1 LRCK 9 C SDTO AK5358 VD VD VA DIF0 1 VD + 1 2 2 C13 47u D1 HSU119 R6 10k U2A 74HC14 1 B 2 3 4 B PDN 1 H 3 L U2B 74HC14 C14 0.1u 2 SW2 PDN 6 VD 5 U2C 74HC14 for 74HC14 8 C15 0.1u 9 U2D 74HC14 10 11 U2E 74HC14 12 A 13 A U2F 74HC14 Title Size A3 Date: A B C D AKD5358-B Document Number Rev AK5358 Monday, June 27, 2005 Sheet E 0 1 of 2 A B C D E VCC REG E E + + C16 47u C17 10u C18 0.1u DIF0 DIF1 C 1 IPS0 2 AVDD R 37 D INT1 39 40 VCOM 42 41 AVSS NC RX0 43 44 RX1 45 TEST1 46 RX2 NC RX3 47 48 + D 38 C19 0.47u INT0 36 NC OCKS0 35 3 DIF0 OCKS1 34 4 TEST2 CM1 33 5 DIF1 CM0 32 MCLK SCLK LRCK U3 AK4114 NC PDN 31 PDN C20 10p 7 DIF2 XTI 30 8 IPS1 XTO 29 9 P/SN DAUX 28 10 XTL0 MCKO2 27 11 XTL1 BICK 26 12 VIN SDTO 25 1 2 3 4 5 10 9 8 7 6 C DSP SDTO 1 6 PORT1 MCLK SCLK LRCK SDTO 2 X1 12.288MHz C24 10u C25 10u LRCK B 24 MCKO1 23 22 DVSS DVDD C23 0.1u + 21 VOUT 20 UOUT 19 COUT 18 BOUT 17 TX1 16 15 DVSS 14 C22 0.1u + 13 TVDD B TX0 C21 10p JP5 MCLK PORT2 A IN VCC 3 2 GND 1 DIT A C26 0.1u Title Size A3 Date: A B C D AKD5358-B Document Number Rev AK4114 Monday, June 27, 2005 Sheet E 0 2 of 2