AMIS-710201: 200dpi CIS Module Data Sheet 1.0 General Description The AMIS-710201 (PI201M-A4) is a contact image sensor (CIS) module using MOS image sensor technology for high-speed performance and high sensitivity. The AMIS-710201 is suitable for scanning A4 size (216mm) documents with 8 dots per millimeter (dpm) resolution. Applications include document scanners, mark readers and other office automation equipment. 2.0 Key Features • • • • • • • • Light source, lens and sensor are integrated into a single module 8dpm resolution, 216mm scanning length 1.72ms/line scanning speed Wide dynamic range analog output Yellow-Green light source Compact size – 13.5mm x 18mm x 232mm Low power Light weight 3.0 Functional Description The AMIS-710201 imaging array consists of 27 sensors that are cascaded to provide 1728 photo-detectors with their associated multiplex switches and a digital shift register that controls its sequential readout. Mounted in the module is a one-to-one graded indexed micro lens array that focuses the scanned documents to image onto its sensing plane. The on-board amplifier processes the video signal to produce a sequential stream of video at the video output pin of the AMIS-710201 module. Figure 1: AMIS-710201 Cross Section AMI Semiconductor – May 06, M-20539-001 www.amis.com 1 AMIS-710201: 200dpi CIS Module Data Sheet Illumination is by means of an integrated LED light source. All components are housed in a small plastic housing which has a cover glass which acts as the focal point for the object being scanned and protects the imaging array, micro lens assembly and LED light source from dust. I/O to the module is the 10-pin connector located on one end of the module. The cross section of the AMIS-710201 is shown in Figure 1 and the block diagram in Figure 2. Figure 2: AMIS-710201 Module Block Diagram 4.0 Absolute Maximum Rating Table 1: Absolute Maximum Rating Parameter Power supply voltage Symbols Vdd Maximum Rating 10 Units V Input clock pulse (high level) Idd Vn In VLED ILED Vih 40 -15 10 5.25 650 Vdd – 0.5V mA V mA V ma V Input clock pulse (low level) Vil -0.8 V AMI Semiconductor – May 06, M-20539-001 www.amis.com 2 AMIS-710201: 200dpi CIS Module Data Sheet 5.0 Recommended Operating Conditions (25°C) ° Table 2: Recommended Operating Conditions (25 C) Item Symbol Power supply Vdd Vn. VLED Idd Ivn ILED Input voltage at digital high Vih Input voltage at digital low Vil Clock frequency f Clock pulse high duty cycle Clock pulse high duration Integration time Tint Operating temperature Top Min. 4.5 -4.5 Typical 5.0 -5 5 11 6.0 350 Vdd-.5 Vdd-1.0 0 Max. 5.5 -12 Units V V V ma ma ma V V MHz % ns ms ° C 30 10.0 550 Vdd 0.8 (1) 1.0 25 250 1.728 10.0 50 25 Note: 1. The module will produce video above 1.5MHz, but with adjacent pixel smearing. Hence, with signal degradation it can be used above 1.5MHz. Table 3: Operating Environment Parameter Operating temperature Operating humidity Storage temperature Storage humidity Symbols Top Hop Tstg Hstg Maximum Rating 0 to 50 10 to 85 -25 to+75 10 to 90 Units °C % °C % 6.0 Electro-Optical Characteristics (25oC) Table 4: Electro-Optical Characteristics (25°C) Parameter Number of photo detectors Pixel-to-pixel spacing Line scanning rate Symbol Tint (1) (2) Clock frequency (3) Bright output voltage (4) Bright output non-uniformity (5) Adjacent pixel non-uniformity (6) Dark non-uniformity (6) Dark output voltage (7) Modulation transfer function Parameter 1728 125 1.728 Units Elements µm ms 1.0 0.6 <+/-30 <25 <200 <200 >30 MHz Volts % % mV mV % Note @ 1.0MHz clock frequency Definitions: 1. Tint: line scanning rate or integration time. Tint is determined by the interval of two start pulse (SP). 2. f: main clock frequency. 3. Vpavg = ∑ Vp(n)/1728 4. Up = [(Vpmax - Vp) / Vp] x 100% or [(Vp - Vpmin) / Vp] x 100%. 5. Upadj = MAX[ | (Vp(n) - Vp(n+l) | / Vp(n)] x 100% Upadj is the nonuniformity percentage pixel-to-pixel. 6. Ud = Vdmax – Vdmin Vdmin is the minimum output on a black document(O.D.=0.8). Vdmax: maximum output voltage of black document (O.D.= 0.8). 7. MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100 [%] Vmax: maximum output voltage at 4.0lp/mm Vmin: minimum output voltage at 4.0lp/mm. 8. lp / mm: line pair per mm. 9. O.D. Optical Density AMI Semiconductor – May 06, M-20539-001 www.amis.com 3 AMIS-710201: 200dpi CIS Module Data Sheet 7.0 Switching Characteristics (25°C) Note: See timing symbol definitions in the following table Figure 3: AMIS-710201 Timing Diagram Table 5: Symbol Definitions for the Above Timing Diagram Item Symbol Clock cycle time to Clock pulse width tw Clock duty cycle Prohibit crossing time of start tprh pulse Data setup time tds Data hold time tdh Signal delay time tdl Signal settling time tsh AMI Semiconductor – May 06, M-20539-001 www.amis.com Min. 1.0 250 25 15 Typical Max. 4.0 75 20 20 50 350 Units µs ns % ns ns ns ns ns 4 AMIS-710201: 200dpi CIS Module Table 6: Pin Configurations Pin Number 1 2 3 4 5 6 7 8 9 10 Symbol Vout Gnd Vdd (+5V) Vn (-5V to –12V) Gnd SP Gnd CP GLED VLED AMI Semiconductor – May 06, M-20539-001 www.amis.com Names and Functions Analog video output Ground; 0V Positive power supply Negative power supply Ground; 0V Shift register start pulse Ground; 0V Sampling clock pulse Ground for the light source; 0V Supply for the light source 5 Data Sheet AMIS-710201: 200dpi CIS Module 8.0 Mechanical Model Dimensions Figure 4: Mechanical Model Dimensions AMI Semiconductor – May 06, M-20539-001 www.amis.com 6 Data Sheet AMIS-710201: 200dpi CIS Module Data Sheet 9.0 Company or Product Inquiries For more information about AMI Semiconductor, our technology and our product, visit our Web site at: http://www.amis.com North America Tel: +1.208.233.4690 Fax: +1.208.234.6795 Europe Tel: +32 (0) 55.33.22.11 Fax: +32 (0) 55.31.81.12 Production Technical Data - The information contained in this document applies to a product in production. AMI Semiconductor and its subsidiaries (“AMIS”) have made every effort to ensure that the information is accurate and reliable. However, the characteristics and specifications of the product are subject to change without notice and the information is provided “AS IS” without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify that data being relied on is the most current and complete. AMIS reserves the right to discontinue production and change specifications and prices at any time and without notice. Products sold by AMIS are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMIS makes no other warranty, express or implied, and disclaims the warranties of noninfringement, merchantability, or fitness for a particular purpose. AMI Semiconductor's products are intended for use in ordinary commercial applications. These products are not designed, authorized, or warranted to be suitable for use in life-support systems or other critical applications where malfunction may cause personal injury. Inclusion of AMIS products in such applications is understood to be fully at the customer’s risk. Applications requiring extended temperature range, operation in unusual environmental conditions, or high reliability, such as military or medical life-support, are specifically not recommended without additional processing by AMIS for such applications. Copyright © 2006 AMI Semiconductor, Inc. AMI Semiconductor – May 06, M-20539-001 www.amis.com 7