AMI N256S08XXHDA

AMI Semiconductor, Inc.
N256S0818HDA/N256S0830HDA
Advance Information
ULP Memory Solutions
670 North McCarthy Blvd. Suite 220
Milpitas, CA 95035
PH: 408-935-7777, FAX: 408-935-7770
256Kb Low Power Serial SRAMs
32K × 8 bit Organization
Overview
Features
The AMI Semiconductor serial SRAM family
includes several integrated memory devices
including this 256Kb serially accessed Static
Random Access Memory, internally organized as
32K words by 8 bits. The devices are designed and
fabricated using AMI’s advanced CMOS
technology to provide both high-speed
performance and low power. The devices operate
with a single chip select (CS) input and use a
simple Serial Peripheral Interface (SPI) serial bus.
A single data in and data out line is used along with
a clock to access data within the devices. The
N256S08xxHDA devices include a HOLD pin that
allows communication to the device to be paused.
While paused, input transitions will be ignored.
The devices can operate over a wide temperature
range of -40oC to +85oC and can be available in
several standard package offerings.
• Power Supply Options
1.8V to 3.6V
• Very low standby current
As low as 200nA
• Very low operating current
As low as 500uA
• Simple memory control
Single chip select (CS)
Serial input (SI) and serial output (SO)
• Flexible operating modes
Word read and write
Page mode (32 word page)
Burst mode (full array)
• Organization
32K x 8 bit
• Self timed write cycles
• Built-in write protection (CS high)
• HOLD pin for pausing communication
• High reliability
Unlimited write cycles
• RoHS Compliant Packages
Green SOIC and TSSOP
Device Options
Part Number
N256S0818HDA
N256S0830HDA
Density
256Kb
Power
Supply (V)
Speed
(MHz)
1.8
20
3.0
25
Feature
HOLD
Typical
Standby
Current
200nA
1uA
Read/Write
Operating Current
500 uA @ 1Mhz
1
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Package Configurations
Pin Names
Pin Function
CS
1
8
CS
SCK
SI
SO
HOLD
NC
VCC
Chip Select Input
Serial Clock Input
Serial Data Input
Serial Data Output
Hold Input
No Connect
SO
2
7
HOLD
NC
3
6
SCK
VSS
4
5
SI
Power
CS
1
8
VCC
VSS
Ground
SO
2
3
VSS
4
TSSOP
NC
SOIC
Pin Name
VCC
7
HOLD
6
SCK
5
SI
Functional Block Diagram
SCK
HOLD
CS
Clock
Circuitry
Decode
Logic
SRAM
Array
SI
Data In
Receiver
SO
Data Out
Buffer
2
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Absolute Maximum Ratings1
Item
Symbol
Rating
Unit
Voltage on any pin relative to VSS
VIN,OUT
–0.3 to VCC+0.3
V
Voltage on VCC Supply Relative to VSS
VCC
–0.3 to 4.5
V
Power Dissipation
PD
500
mW
Storage Temperature
TSTG
–40 to 125
o
Operating Temperature
TA
-40 to +85
o
Soldering Temperature and Time
TSOLDER
260oC, 10sec
o
C
C
C
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min.
Supply Voltage
VCC
1.8V Device
Supply Voltage
VCC
3V Device
Input High Voltage
VIH
Input Low Voltage
VIL
Output High Voltage
VOH
IOH = -0.4mA
Output Low Voltage
VOL
Input Leakage Current
Output Leakage Current
Read/Write Operating
Current
Standby Current
Typ1
Max
Unit
1.7
1.95
V
2.3
3.6
V
0.7 x VCC
VCC+0.3
V
–0.3
0.3 x VCC
V
IOL = 1mA
0.2
V
ILI
CS = VCC, VIN = 0 to VCC
0.5
µA
ILO
CS = VCC, VOUT = 0 to VCC
0.5
µA
ICC1
F = 1MHz, IOUT = 0
500
µA
ICC2
F = 10MHz, IOUT = 0
4
mA
ICC3
F = 20/25MHz, IOUT = 0
8/10
mA
nA
ISB
VCC–0.5
V
1.8V Device
CS = VCC, VIN = VSS or VCC
200
500
3V Device
CS = VCC, VIN = VSS or VCC
1
3
µA
1. Typical values are measured at Vcc=Vcc Typ., TA=25°C and are not 100% tested.
Capacitance1
Item
Symbol
Test Condition
Input Capacitance
CIN
VIN = 0V, f = 1 MHz, TA = 25oC
I/O Capacitance
CI/O
Min
o
VIN = 0V, f = 1 MHz, TA = 25 C
Max
Unit
7
pF
7
pF
1. These parameters are verified in device characterization and are not 100% tested
3
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Timing Test Conditions
Item
Input Pulse Level
0.1VCC to 0.9 VCC
Input Rise and Fall Time
5ns
Input and Output Timing Reference Levels
0.5 VCC
Output Load
CL = 100pF
Operating Temperature
-40 to +85 oC
Timing
1.8V Device
3V Device
Item
Symbol
Clock Frequency
fCLK
20
25
MHz
Clock Rise Time
tR
2
2
us
Clock Fall Time
tF
2
2
us
Clock High Time
tHI
25
20
ns
Clock Low Time
tLO
25
20
ns
Clock Delay Time
tCLD
25
20
ns
CS Setup Time
tCSS
25
20
ns
CS Hold Time
tCSH
50
40
ns
CS Disable Time
tCSD
25
20
ns
SCK to CS
tSCS
5
5
ns
Data Setup Time
tSU
10
10
ns
Data Hold Time
tHD
10
10
ns
Output Valid From Clock Low
tV
Output Hold Time
tHO
Output Disable Time
tDIS
HOLD Setup Time
tHS
10
10
ns
HOLD Hold Time
tHH
10
10
ns
HOLD Low to Output High-Z
tHZ
10
10
ns
HOLD High to Output Valid
tHV
Min.
Max.
Min.
25
0
Max.
20
0
20
50
Units
ns
ns
15
40
ns
ns
4
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Serial Input Timing
tCSD
tCLD
CS
tR
tF
tCSH
tSCS
tCSS
SCK
tSU
tHD
MSB in
SI
LSB in
SO
High-Z
Serial Output Timing
CS
tLO
tHI
tCSH
SCK
tV
tDIS
SO
MSB out
LSB out
SI
Don’t Care
Hold Timing
CS
tHS
tHS
tHH
SCK
tHH
SO
n+2
n+1
n
High-Z
tHV
n
tHZ
SI
n+2
n+1
n-1
tSU
n
Don’t Care
n
n-1
HOLD
5
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Control Signal Descriptions
Signal
Name
I/O
Description
CS
Chip Select
I
A low level selects the device and a high level puts the device in standby mode. If
CS is brought high during a program cycle, the cycle will complete and then the
device will enter standby mode. When CS is high, SO is in high-Z. CS must be
driven low after power-up prior to any sequence being started.
SCK
Serial Clock
I
Synchronizes all activities between the memory and controller. All incoming
addresses, data and instructions are latched on the rising edge of SCK. Data out is
updated on SO after the falling edge of SCK.
SI
Serial Data In
I
Receives instructions, addresses and data on the rising edge of SCK.
SO
Serial Data Out
O
Data is transferred out after the falling edge of SCK.
I
A high level is required for normal operation. Once the device is selected and a
serial sequence is started, this input may be taken low to pause serial communication without resetting the serial sequence. The pin must be brought low while SCK
is low for immediate use. If SCK is not low, the Hold function will not be invoked
until the next SCK high to low transition. The device must remain selected during
this sequence. SO is high-Z during the Hold time and SI and SCK are inputs are
ignored. To resume operations, HOLD must be pulled high while the SCK pin is
low.
Lowering the HOLD input at any time will take to SO output to High-Z.
HOLD
Hold
Functional Operation
Basic Operation
The 256Kb serial SRAM is designed to interface directly with a standard Serial Peripheral Interface (SPI)
common on many standard micro-controllers. It may also interface with other non-SPI ports by
programming discrete I/O lines to operate the device.
The serial SRAM contains an 8-bit instruction register and is accessed via the SI pin. The CS pin must be
low and the HOLD pin must be high for the entire operation. Data is sampled on the first rising edge of
SCK after CS goes low. If the clock line is shared, the user can assert the HOLD input and place the
device into a Hold mode. After releasing the HOLD pin, the operation will resume from the point where it
was held.
The following table contains the possible instructions and formats. All instructions, addresses and data are
transferred MSB first and LSB last.
Instruction Set
Instruction
Instruction Format
READ
0000 0011
Description
Read data from memory starting at selected address
WRITE
0000 0010
Write data to memory starting at selected address
RDSR
0000 0101
Read status register
WRSR
0000 0001
Write status register
6
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
READ Operations
The serial SRAM READ is selected by enabling CS low. First, the 8-bit READ instruction is transmitted to
the device followed by the 16-bit address with the MSB being a don’t care. After the READ instruction and
addresses are sent, the data stored at that address in memory is shifted out on the SO pin after the output
valid time from the clock edge.
If operating in page mode, after the initial word of data is shifted out, the data stored at the next memory
location on the page can be read sequentially by continuing to provide clock pulses. The internal address
pointer is automatically incremented to the next higher address on the page after each word of data is read
out. This can be continued for the entire page length of 32 words long. At the end of the page, the
addresses pointer will be wrapped to the 0 word address within the page and the operation can be
continuously looped over the 32 words of the same page.
If operating in burst mode, after the initial word of data is shifted out, the data stored at the next memory
location can be read sequentially by continuing to provide clock pulses. The internal address pointer is
automatically incremented to the next higher address after each word of data is read out. This can be
continued for the entire array and when the highest address is reached (7FFFh), the address counter
wraps to the address 0000h. This allows the burst read cycle to be continued indefinitely.
All READ operations are terminated by pulling CS high.
Word READ Sequence
CS
SCK
0
1
2
3
4
5
6
7
8
9
15
14
Instruction
SI
0
0
0
0
0
10
11
21
22
23
2
1
0
24
25
26
7
6
5
27
28
29
30
31
2
1
0
16-bit address
0
1
1
13
12
Data Out
SO
High-Z
4
3
7
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Page and Burst READ Sequence
CS
SCK
0
1
2
3
4
5
6
7
8
9
Instruction
SI
0
0
0
0
10
11
21
22
23
2
1
0
24
25
26
27
28
29
30
31
1
0
16-bit address
0
0
1
15
1
14
13
12
Don’t Care
ADDR 1
Data Out from ADDR 1
7
High-Z
SO
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
6
5
4
3
2
47
Don’t Care
Data Out from ADDR 3
Data Out from ADDR 2
7
6
5
4
3
2
1
0
7
6
5
4
3
2
Data Out from ADDR n
1
0 ...
7
6
5
4
3
2
1
0
Page READ Sequence
SI
16-bit address
Page address (X)
Word address (Y)
Data Words: sequential, at the end of the page the
address wraps back to the beginning of the page
SO
Page X
Page X
Word Y
Word Y+1 Word Y+2
Page X
Page X
Page X
Page X
Word 31
Word 0
Word 1
Burst READ Sequence
SI
Data Words: sequential, at the end of the page the address wraps to the beginning
of the page and continues incrementing up to the starting word address. At that
time, the address increments to the next page and the burst continues.
16-bit address
Page address (X)
Word address (Y)
...
SO
...
Page X
Page X
Page X
Page X
Page X
Page X
Word Y
Word Y+1
Word 31
Word 0
Word 1
Word Y-1 Word Y
Page X+1 Page X+1
Word Y+1
8
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
WRITE Operations
The serial SRAM WRITE is selected by enabling CS low. First, the 8-bit WRITE instruction is transmitted
to the device followed by the 16-bit address with the MSB being a don’t care. After the WRITE instruction
and addresses are sent, the data to be stored in memory is shifted in on the SI pin.
If operating in page mode, after the initial word of data is shifted in, additional data words can be written as
long as the address requested is sequential on the same page. Simply write the data on SI pin and
continue to provide clock pulses. The internal address pointer is automatically incremented to the next
higher address on the page after each word of data is written in. This can be continued for the entire page
length of 32 words long. At the end of the page, the addresses pointer will be wrapped to the 0 word
address within the page and the operation can be continuously looped over the 32 words of the same
page. The new data will replace data already stored in the memory locations.
If operating in burst mode, after the initial word of data is shifted in, additional data words can be written to
the next sequential memory locations by continuing to provide clock pulses. The internal address pointer
is automatically incremented to the next higher address after each word of data is read out. This can be
continued for the entire array and when the highest address is reached (7FFFh), the address counter
wraps to the address 0000h. This allows the burst write cycle to be continued indefinitely. Again, the new
data will replace data already stored in the memory locations.
All WRITE operations are terminated by pulling CS high.
Word WRITE Sequence
CS
SCK
0
1
2
3
4
5
6
7
8
9
15
14
Instruction
SI
SO
0
0
0
0
0
10
11
21
22
23
24
25
26
2
1
0
7
6
5
16-bit address
0
1
0
13
12 ...
27
28
29
30
31
3
2
1
0
Data In
4
High-Z
9
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Page and Burst WRITE Sequence
CS
SCK
0
1
2
3
4
5
6
7
8
9
15
14
Instruction
SI
0
0
0
0
10
11
21
22
23
24
25
26
27
28
29
30
31
2
1
0
7
6
5
4
3
2
1
0
16-bit address
0
0
1
0
13
12
ADDR 1
SO
Data In to ADDR 1
High-Z
32
33
34
35
36
37
38
39
40
6
5
4
3
42
43
44
45
46
47
Data In to ADDR 3
Data In to ADDR 2
7
41
2
1
0
7
6
5
4
3
Data In to ADDR n
2
1
0 ...
7
6
5
4
3
2
1
0
High-Z
Page WRITE Sequence
Data Words: sequential, at the end of the page the
address wraps back to the beginning of the page
SI
16-bit address
Page address (X)
Word address (Y)
Page X
Page X
Word Y
Word Y+1 Word Y+2
Page X
Page X
Page X
Page X
Word 31
Word 0
Word 1
High-Z
SO
Burst WRITE Sequence
...
SI
16-bit address
Page address (X)
Word address (Y)
...
Page X
Page X
Page X
Page X
Page X
Page X
Word Y
Word Y+1
Word 31
Word 0
Word 1
Word Y-1 Word Y
Page X+1 Page X+1
Word Y+1
Data Words: sequential, at the end of the page the address wraps to the beginning of the page and
continues incrementing up to the starting word address. At that time, the address increments to the
next page and the burst continues.
SO
High-Z
10
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
WRITE Status Register Instruction (WRSR)
This instruction provides the ability to write the status register and select among several operating modes.
Several of the register bits must be set to a low ‘0’ if any of the other bits are written. The timing sequence
to write to the status register is shown below, followed by the organization of the status register.
WRITE Status Register Sequence
CS
SCK
0
1
2
3
4
5
6
7
8
9
Instruction
SI
0
0
0
0
10
11
12
13
14
15
1
0
Status Register Data In
0
0
0
1
7
6
5
4
3
2
High-Z
SO
Status Register
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mode
Reserved
Reserved
Hold Function
0 0 = Word Mode
Must = 0
Must = 0
0 = Hold (Default)
(Default)
1 = No Hold
1 0 = Page Mode
0 1 = Burst Mode
1 1 = Reserved
11
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
READ Status Register Instruction (RDSR)
This instruction provides the ability to read the Status register. The register may be read at any time by
performing the following timing sequence.
READ Status Register Instruction (RDSR)
CS
SCK
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Instruction
SI
0
0
0
0
0
1
0
1
Status Register Data Out
SO
High-Z
7
6
5
4
3
2
1
0
Power-Up State
The serial SRAM enters a know state at power-up time. The device is in low-power standby state with CS
= 1. A low level on CS is required to enter a active state.
12
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
8-Lead Plastic Small Outline, 150mil SOIC
E
E1
p
D
α
B
A2
A1
A
h
45o
c
φ
β
L
Parameter
Sym
Min
Nom
Max
Pin Pitch
p
Overall height
A
1.35
1.27
1.55
1.75
Molded Package Thickness
A2
1.32
1.42
1.55
0.25
Standoff
A1
0.10
0.18
Overall Width
E
5.79
6.02
6.20
Molded Package Width
E1
3.71
3.91
3.99
Overall Length
D
4.80
4.90
5.00
Chamfer Distance
h
0.25
0.38
0.51
Foot Length
L
0.48
0.62
0.76
Foot Angle
φ
0
4
8
Lead Thickness
c
0.20
0.23
0.25
Lead Width
B
0.33
0.42
0.51
Mold Draft Angle Top
α
0
12
15
Mold Draft Angle Bottom
β
0
12
15
Note:
1. All dimensions in Millimeters
2. Package dimensions exclude mold flash and protusions.
13
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
8-Lead Plastic Thin Shrink Small Outline, 4.4 mm TSSOP
E
E1
p
D
B
α
A2
A1
A
c
φ
β
L
Parameter
Sym
Min
Nom
Max
Pin Pitch
p
Overall height
A
0.65
Molded Package Thickness
A2
0.85
0.90
0.95
0.15
1.10
Standoff
A1
0.05
0.10
Overall Width
E
6.25
6.38
6.50
Molded Package Width
E1
4.30
4.40
4.50
Overall Length
D
2.90
3.00
3.10
Foot Length
L
0.50
0.60
0.70
Foot Angle
φ
0
4
8
Lead Thickness
c
0.09
0.15
0.20
Lead Width
B
0.19
0.25
0.30
Mold Draft Angle Top
α
0
5
10
Mold Draft Angle Bottom
β
0
5
10
Note:
1. All dimensions in Millimeters
2. Package dimensions exclude mold flash and protusions.
14
This is a developmental specification and is subject to change without notice.
N256S0818HDA/N256S0830HDA
Advance Information
AMI Semiconductor, Inc.
Ordering Information
N256S08 XX XX A X- XX I
Performance
25 = 25MHz
20 = 20MHz
Package
S2 = Green SOIC (RoHS Compliant)
T2 = Green TSSOP (RoHS Compliant)
Function
Voltage
HD = Hold Function Input
18 = 1.8V
30 = 3V
Revision History
Revision #
Date
Change Description
A
October 2005
Initial advance release
B
January 2006
Separated density, removed write protection and added page and burst modes
C
January 2006
Changed packages to green type
D
January 2006
Changed TSSOP pinout to match SOIC
E
September 2006
Split x8 and x16 devices
Converted to AMI Semiconductor
© 2006 AMI Semiconductor, Inc. All rights reserved.
AMI Semiconductor, Inc. ("AMIS") reserves the right to change or modify the information contained in this data sheet and the products described therein, without prior notice.
AMIS does not convey any license under its patent rights nor the rights of others. Charts, drawings and schedules contained in this data sheet are provided for illustration purposes only and they vary depending upon specific applications.
AMIS makes no warranty or guarantee regarding suitability of these products for any particular purpose, nor does AMIS assume any liability arising out of the application or use of
any product or circuit described herein. AMIS does not authorize use of its products as critical components in any application in which the failure of the AMIS product may be
expected to result in significant injury or death, including life support systems and critical medical instruments.
15
This is a developmental specification and is subject to change without notice.