PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications General Description Features The AAT2846 is a highly integrated charge pump with dual linear regulators optimized for systems powered from lithium-ion/polymer batteries. The charge pump provides power for both white LED backlight and flash. Six backlight LEDs can be driven at up to 30mA each, while up to two flash LEDs can be driven at up to 600mA total. AnalogicTech’s AS2Cwire™ (Advanced Simple Serial Control™) single-wire interface is used to enable, disable, and set the current to one of 32 levels for the backlight and one of 16 levels for the flash. An external resistor sets the maximum flash current. Backlight current matching is 1% for uniform display brightness, and flash current matching is 4% for uniform power dissipation. • Input Voltage Range: 2.7V to 5.5V • Tri-Mode Charge Pump: ▪ Drives up to Six Backlight LEDs and Two Flash LEDs ▪ 32 Programmable Backlight Current Settings Ranging from 95µA to 30mA ▪ 16 Programmable Flash Current Settings ▪ Maximum Flash LED Current Programmable using External Resistor ▪ 2MHz Switching Frequency • Two Linear Regulators: ▪ 200mA Output Current ▪ 200mV Dropout Voltage ▪ Output Voltage Adjustable from 1.2V to VBATTERY ▪ Output Auto-Discharge for Fast Shutdown ▪ Individual LDO Enable Inputs • Built-In Thermal Protection • Automatic Soft Start • -40°C to +85°C Temperature Range • TQFN44-28 Package The AAT2846 offers two high-performance low-noise MicroPower™ low dropout (LDO) linear regulators. Both regulators use individual enable inputs and each will supply up to 200mA load current. LDO ground pin current is only 80µA, making the AAT2846 ideal for batteryoperated applications. The AAT2846 is equipped with built-in short-circuit and over-temperature protection. The soft start circuitry prevents excessive inrush current at start-up and mode transitions. The AAT2846 is available in a Pb-free TQFN44-28 package and operates over the -40°C to +85°C ambient temperature range. Applications • Camera-Enabled Mobile Devices • Digital Still Cameras • Multimedia Mobile Phones Typical Application C2 1µF C1 1µF C1+ C1- C2+ IN CIN 4.7µF VBAT IN AAT2846 ENABLE/SET ENS EN_FLASH FEN CT CT 0.1µF FSET RFSET 280k REF CBYP 0.1µF EN_LDOA EN_LDOB VOUT COUT 2.2µF BL1 BL2 BL3 BL4 BL5 BL6 FL1 FL2 OUTA VOUT LDOA R2A FBA COUTA R1A ENA ENB AGND 2846.2008.03.1.1 C2- OUT VOUT LDOB OUTB R2B FBB PGND www.analogictech.com COUTB R1B 1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Pin Descriptions Pin # Symbol 1 BL3 2 BL2 3 BL1 4 AGND 5 CT 6 REF 7 FBB 8 OUTB 9, 18 IN 10 FBA 11 OUTA 12 13 C1C1+ 14 OUT 15 ENB 16 17 19 C2+ C2PGND 20 ENS 21 FL2 22 FL1 23 FEN 24 FSET 25 BL6 26 BL5 27 ENA 28 BL4 EP 2 Description Backlight LED 3 current sink. BL3 controls the current through backlight LED 3. Connect the cathode of backlight LED 3 to BL3. If not used, connect BL3 to OUT. Backlight LED 2 current sink. BL2 controls the current through backlight LED 2. Connect the cathode of backlight LED 2 to BL2. If not used, connect BL2 to OUT. Backlight LED 1 current sink. BL1 controls the current through backlight LED 1. Connect the cathode of backlight LED 1 to BL1. If not used, connect BL1 to OUT. Analog ground. Connect AGND to PGND at a single point as close to the AAT2846 as possible. Flash timer control capacitor input. Connect a capacitor from CT to AGND to set the flash timer. A 100nF capacitor sets the timer to 1 second. Reference output. Bypass REF to AGND with a 0.1µF or larger ceramic capacitor. Feedback input for LDO B. FBB measures the output voltage of LDO B. Connect a resistive voltage divider from the output of LDO B to FBB. FBB feedback regulation voltage is 1.2V. LDO B regulated voltage output. OUTB is the voltage output of LDO B. Bypass OUTB to AGND with a 2.2µF or larger ceramic capacitor as close to the AAT2846 as possible. Power input. Connect IN to the input source voltage. Bypass IN to PGND with a 4.7µF or larger ceramic capacitor as close to the AAT2846 as possible. Feedback input for LDO A. FBA measures the output voltage of LDO A. Connect a resistive voltage divider from the output of LDO A to FBA. FBA feedback regulation voltage is 1.2V. LDO A regulated voltage output. OUTA is the voltage output of LDO A. Bypass OUTA to AGND with a 2.2µF or larger ceramic capacitor as close to the AAT2846 as possible. Negative node of charge pump capacitor 1. Connect the 1µF charge pump capacitor 1 from C1+ to C1-. Positive node of charge pump capacitor 1. Connect the 1µF charge pump capacitor 1 from C1+ to C1-. Charge pump output; supplies current to the backlight and flash LEDs. Connect the backlight and flash LED anodes to OUT. Bypass OUT to PGND with a 2.2µF or larger ceramic capacitor as close to the AAT2846 as possible. LDO B enable input. ENB turns on or off low dropout regulator B (LDO B). Drive ENB high to turn on LDO B; drive it low to turn it off. Positive node of charge pump capacitor 2. Connect the 1µF charge pump capacitor 2 from C2+ to C2-. Negative node of charge pump capacitor 2. Connect the 1µF charge pump capacitor 2 from C2+ to C2-. Power ground. Connect AGND to PGND at a single point as close to the AAT2846 as possible. Flash and backlight enable and serial control input. ENS turns on/off both the flash and backlight and is the AS2Cwire input to serially control the backlight and movie-mode flash LED brightness. Flash LED 2 current sink. FL2 controls the current through flash LED 2. Connect the cathode of flash LED 2 to FL2. If not used, connect FL2 to OUT. Flash LED 1 current sink. FL1 controls the current through flash LED 1. Connect the cathode of flash LED 1 to FL1. If not used, connect FL1 to OUT. Flash enable input. FEN is the on/off control for the flash LEDs. Drive FEN high to drive the maximum flash current, set by RFSET, through the flash LEDs. Flash current setting input. A 280kΩ resistor from FSET to AGND sets the maximum flash LED current. Backlight LED 6 current sink. BL6 controls the current through backlight LED 6. Connect the cathode of backlight LED 6 to BL6. If not used, connect BL6 to OUT. Backlight LED 5 current sink. BL5 controls the current through backlight LED 5. Connect the cathode of backlight LED 5 to BL5. If not used, connect BL5 to OUT. LDO A enable input. ENA turns on or off low dropout regulator A (LDO A). Drive ENA high to turn on LDO A; drive low to turn it off. Backlight LED 4 current sink. BL4 controls the current through backlight LED 4. Connect the cathode of backlight LED 4 to BL4. If not used, connect BL4 to OUT. Exposed paddle (bottom); connect to ground as closely as possible to the device. www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Pin Configuration TQFN44-28 (Top View) FL1 FEN FSET BL6 BL5 ENA BL4 28 BL3 BL2 BL1 AGND CT REF FBB 27 26 25 24 23 22 1 21 2 20 3 19 4 18 5 17 6 16 7 15 8 9 10 11 12 13 14 FL2 ENS PGND IN C2C2+ ENB OUT C1+ C1OUTA FBA IN OUTB Absolute Maximum Ratings1 Symbol TJ TLEAD Description IN, OUT, FL1, FL2, BL1, BL2, BL3, BL4, BL5, BL6 Voltage to PGND FSET, CT, REF, FBB, OUTA, FBA, OUTB, ENA, ENB, FEN, ENS C1+, C1-, C2+, C2- Voltage to PGND PGND Voltage to AGND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value Units -0.3 to 6.0 V -0.3 to VIN + 0.3 V -0.3 to 0.3 -40 to 150 300 V °C °C Value Units 2 50 W °C/W Thermal Information2 Symbol PD θJA Description Maximum Power Dissipation3 Maximum Thermal Resistance 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on a FR4 circuit board. 3. Derate 6.25mW/°C above 25°C ambient temperature. 2846.2008.03.1.1 www.analogictech.com 3 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Electrical Characteristics1 VIN = 3.6V; CIN = 4.7µF; COUT = 2.2µF; C1 = C2 = 1µF; RFSET = 280kΩ; TA = -40°C to +85°C, unless otherwise noted. Typical values are TA = 25°C. Symbol VIN IIN(Q) Description Conditions IN Operating Voltage Range IN Operating Current ∆I(BL_) BL1-BL6 Maximum Current BL1-BL6 Current Matching BL1-BL6 Charge Pump Mode Transition Threshold FL1-FL2 Flash LED Outputs IFL_(MAX) FL1-FL2 Maximum Current ∆I(FL_) FL1-FL2 Current Matching2 FL1-FL2 Charge Pump Mode Transition VFL_(TH) Threshold ENS, FEN Logic Control VENS(L) ENS, FEN Input Low Threshold ENS, FEN Input High Threshold VENS(H) IENS, IFEN ENS, FEN Input Leakage Current tENS(LOW) ENS, FEN Serial Interface Low Time tENS(HI_MIN), ENS, FEN Serial Interface Minimum High Time tENS(HI_MIN) tENS(HI_MAX), ENS, FEN Serial Interface Maximum High Time tENS(HI_MAX) tENS(OFF), ENS, FEN Off Timeout tFEN(OFF) tENS(LAT), ENS, FEN Serial Interface Latch Timeout tFEN(LAT) 2 Typ 2.7 IIN(SHDN) IN Shutdown Current TSD Over-Temperature Shutdown Threshold TSD(HYS) Over-Temperature Shutdown Hysteresis Charge Pump Section IOUT OUT Maximum Output Current VIN(TH_H) Charge Pump Mode Hysteresis fOSC Charge Pump Oscillator Frequency BL1-BL6 Backlight LED Outputs IBL_(MAX) Min 1X Mode, 3.0V ≤ VIN ≤ 5.5V, Active, No Load; ENL = AGND, FEN = ENS = IN 1.5X Mode, 3.0V ≤ VIN ≤ 5.5V, Active, No Load; ENL = AGND, FEN = ENS = IN 2X Mode, 3.0V ≤ VIN ≤ 5.5V, Active, No Load; ENL = AGND, FEN = ENS = IN ENA = ENB = ENS = FEN = AGND Units 5.5 V 1 4 1.0 18 140 15 µA °C °C 600 500 2 mA mV MHz 20 30 22 1.0 150 Address 4, Data 1; VIN - VF = 1.5V Address 4, Data 1; VIN - VF = 1.5V 270 300 330 4.0 1.0 75 50 VIN ≥ 3.3V % mA % mV 0.4 1.4 -1.0 0.3 mA mV 300 VENS or VFEN = VIN = 5V VIN ≥ 3.3V mA 5 Address 0, Data 1 TA = 25°C Address 0, Data 1; VIN - VF = 1.5V Address 12, Data 2; VIN - VF = 1.5V Address 0, Data 1; VIN - VF = 1.5V Max V V µA µs ns 75 µs 500 µs 500 µs 1. The AAT2846 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. Current matching is defined as the deviation of any sink current from the average of all active channels. 4 www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Electrical Characteristics1 VIN = 3.6V; CIN = 4.7µF; COUT = 2.2µF; C1 = C2 = 1µF; RFSET = 280kΩ; TA = -40°C to +85°C, unless otherwise noted. Typical values are TA = 25°C. Symbol Description Conditions Min Typ Max Units IOUT = 1mA to 200mA ENA = ENB = IN, ENS = AGND 1.17 1.2 1.23 200 V Linear Regulators VFBA, VFBB IOUTA(MAX), IOUTB(MAX) VOUTA(DO), VOUTB(DO) PSRRA, PSRRB VEN_(L) VEN_(H) tEN_(DLY) Feedback Voltage Tolerance OUTA, OUTB Maximum Load Current 200 OUTA, OUTB Dropout Voltage IOUT = 150mA OUTA, OUTB Power Supply Rejection Ratio IOUT = 10mA, CREF = 10nF, 1kHz ENA, ENB Voltage Low Threshold ENA, ENB Voltage High Threshold ENA, ENB Enable Delay mA 150 300 50 dB 0.4 1.4 REF = Open 15 mV V V µs 1. The AAT2846 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2846.2008.03.1.1 www.analogictech.com 5 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Typical Characteristics Backlight Efficiency vs. Input Voltage Flash Efficiency vs. Input Voltage 100 100 20mA/ch 80 70 60 50 72mA/ch 150mA/ch 90 Efficiency (%) Efficiency (%) 90 10.2mA/ch 1.6mA/ch 80 70 60 50 40 40 30 30 2.7 3.1 3.5 3.9 4.3 4.7 5.1 2.7 5.5 3.1 3.5 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) Input Voltage (V) Flash Current Matching vs. Temperature Backlight Current Matching vs. Temperature (150mA/Ch; Data 6) (20mA/ch; Data 1) 170 21.0 LED Current (mA) LED Current (mA) 165 20.5 20.0 19.5 19.0 18.5 -40 160 155 150 145 140 135 -15 10 35 60 85 130 -40 -15 10 Turn On to 1X Mode Backlight Turn On to 1.5X Mode Backlight (30mA/ch; Data 1; VIN = 4.2V) (30mA/ch; Data 1; VIN = 3.4V) VEN (2V/div) 0V VOUT (2V/div) 0V VOUT (2V/div) VSINK (500mV/div) 0V VSINK (500mV/div) IIN (200mA/div) IIN (200mA/div) 0A Time (200µs/div) 6 60 85 Temperature (°C) Temperature (°C) VEN (2V/div) 35 0V 0V 0V 0A Time (200µs/div) www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Typical Characteristics VEN (2V/div) Turn On to 2X Mode Backlight Turn Off from 1.5X Mode Backlight (30mA/ch; Data 1; VIN = 2.7V) (30mA/ch; Data 1) VEN (2V/div) 0V VOUT (2V/div) 0V VSINK (500mV/div) 0V VOUT (2V/div) 0V 0V IIN (200mA/div) IIN (200mA/div) 0A 0A Time (100µs/div) Time (200µs/div) BENS, FENS High Threshold Voltage vs. Input Voltage BENS, FENS Low Threshold Voltage vs. Input Voltage 1.4 1.4 1.3 VBENS(L), VFENS(L) (V) VBENS(H), VFENS(H) (V) 1.3 -40°C 1.2 1.1 1.0 0.9 0.8 25°C 0.7 85°C 1.2 -40°C 1.1 1.0 0.9 0.8 0.7 25°C 0.6 0.6 0.5 0.5 2.7 3.1 3.5 3.9 4.3 4.7 5.1 2.7 5.5 3.1 3.5 Input Voltage (V) 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) BENS, FENS Latch Timeout vs. Input Voltage BENS, FENS Off Timeout vs. Input Voltage 300 260 240 220 VBENS(H), VFENS(H) (V) TBENS(LAT), TFENS(LAT) (µs) 85°C 25°C 200 -40°C 180 160 25°C 140 120 260 25°C -40°C 220 85°C 180 140 100 80 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 100 2.7 Input Voltage (V) 2846.2008.03.1.1 3.1 3.5 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) www.analogictech.com 7 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Typical Characteristics LDOs A and B Turn On Characteristic LDOs A and B Load Regulation VEN (2V/div) Output Voltage Error (%) 1.0 0V VOUT (500mV/div) 0V 0.5 OUTA 0.0 OUTB -0.5 -1.0 0.1 1 10 Time (50µs/div) 3.2 1 3.0 Output Voltage (V) Output Voltage (%) LDOs A and B Dropout Characteristics 1.5 0.5 0 -0.5 -1 -15 10 35 1000 Load Current (mA) LDOs A and B Output Voltage vs. Temperature -1.5 -40 100 60 85 IOUT = 100mA 2.8 2.6 IOUT = 200mA 2.4 2.2 2.0 2.7 2.8 Temperature (°C) 2.9 3.0 3.1 3.2 Input Voltage (V) LDOs A and B Line Transient Response LDOs A and B Load Transient Response (10mA Load) (10mA to 200mA Load Step) VIN = 3.6V IOUT = 200mA IOUT (100mA/div) VIN (250mV/div) VIN = 3.1V VOUT (AC Coupled) (100mV/div) VOUT (AC Coupled) (20mV/div) Time (50µs/div) 8 Time (50µs/div) www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Functional Block Diagram IN IN C1+ C1C2+ OUTA LDO A 1x/1.5x/2x Charge Pump OUTB C2- ENA ENB FBA LDO B To LDO A FBB 1.2V VREF REF To LDO B OUT BL1 BL2 BL3 ENS FEN BL4 Control Logic BL5 BL6 CT FSET FL1 FL2 AGND PGND Functional Description The AAT2846 is a highly integrated backlight and flash LED driver with two LDO linear regulators. The charge pump LED driver drives backlight and flash LEDs from a 2.7V to 5.5V input voltage. The LDO regulators are operated from the same input voltage range and produce regulated output voltages as low as 1.2V. LED Drivers The LEDs are driven from an internal charge pump that, depending on the battery voltage and LED forward voltage, drives LEDs directly from the supply voltage (1X or bypass mode) or steps up the supply voltage by a factor of 1.5 (1.5X mode) or 2 (2X mode). The charge pump requires only two tiny 1µF ceramic capacitors, providing a 2846.2008.03.1.1 more compact solution than typical inductor-based stepup converter solutions. Each individual LED is driven by a current sink to AGND, allowing individual current control with high accuracy over a wide range of input voltages and LED forward voltages while maintaining high efficiency. The charge pump is controlled by the voltage across the LED current sinks. When any one of the active current sinks begins to dropout, the charge pump goes to the next higher mode (from 1X to 1.5X or from 1.5X to 2X mode) to maintain sufficient LED voltage for constant LED current. The AAT2846 continuously monitors the LED forward voltages and uses the input voltage to determine when to reduce the charge pump mode for better efficiency. There is also a 500mV mode-transition hysteresis that prevents the charge pump from oscillating between charge pump modes. www.analogictech.com 9 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications AS2Cwire Serial Interface The backlight and flash LED current levels are dynamically controllable by the AS2Cwire single-wire interface. The backlight section has multiple current level scales and the maximum current level is fixed at 20mA or 30mA, depending on the scale chosen through programming. The flash section maximum current level is user programmable by an external set resistor. The maximum flash current that can be supported by the device is 300mA/channel, or 600mA total. This corresponds to a 280K set resistor value. The AAT2846 is dynamically programmable by the AS2Cwire single-wire interface. AS2Cwire records rising edges detected at the ENS pin to address and load the data registers. AS2Cwire latches data or address after the ENS input has been held high for time TLAT (500µs). Address or data is differentiated by the number of ENS rising edges. Since the data registers are 4 bits each, the differentiating number of pulses is 24 or 16, so that Address 0 is identified by 17 rising edges, Address 1 by 18 rising edges, Address 2 by 19 rising edges, etc. Data is set to any number of rising edges between 1 and 16. A typical write protocol is a burst of ENS rising edges identifying a particular address, followed by a pause with ENS held high for the TLAT timeout period, then a burst of rising edges signifying data, and another TLAT timeout after the data has been sent. Once an address is set, multiple writes to that address are allowed since the address is not reset after each write. Address edges are needed when changing the address, or writing to an address other than the default after shutdown. Address 0 is the default address after shutdown. If the part is enabled with only data edges and no address, then Address 0 will be programmed and backlight channels BL1-BL6 will turn-on according to the number of data edges applied. For maximum LED current lower than 300mA, use a programming resistor greater than 280kΩ up to 1MΩ. Calculate the flash programming resistor value using the equation: RFSET = 280k · 300mA Ω IFMAX where IFMAX is the maximum flash LED current in mA. If any one of the backlight or flash current sinks is not used, connect that current sink to OUT. The current controller monitors the sink voltage and, if it is connected to OUT, then the controller determines that the current sink is not used or that the LED is shorted. In either case, the controller turns off the affected current sink. When ENS is held low for a time greater than TOFF (500µs), the AAT2846 enters shutdown mode and draws less than 1µA of current from IN. At shutdown, the data and address registers are reset to 0. Address Data T HI T LO TLAT TLAT EN/SET 1 Address 2 17 18 1 0 2... n ≤ 16 1 Data Reg 1 0 Data Reg 2 0 n Figure 1: AS2Cwire Serial Interface Timing. 10 www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications AS2Cwire Serial Interface Addressing 0 1 2 3 4 5 17 18 19 20 21 22 12 29 15 Sub-2 Sub-3 32 19 20 30.0 Function 25.0 Backlight Current BL1-BL6 Main Backlight Current BL1-BL5 Sub Backlight Current BL6 Low Current Backlight Flash Current FL1, FL2 Independent Flash On/Off Control Maximum Backlight Current (Main and Sub) Backlight Independent Control BL3-BL6 On/Off Control BL1/BL2 On/Off Control Table 1: AS2Cwire Serial Interface Addressing. Backlight Current Control (Address 0-3) Use Addresses 0-3 to program all six backlight LED channels. All six backlight channels are programmed to the same current level by writing Address 0 followed by any Data between 1 and 16. To program only the main channels BL1 through BL5, use Address 1. Similarly, use Address 2 to independently program subchannel BL6 only. Data 30mA Max (mA) 20mA Max (mA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 30.0 27.9 26.1 24.2 21.0 19.2 17.3 15.0 12.7 10.9 8.1 6.2 4.4 3.5 2.6 0 20.0 19.0 17.8 16.5 14.3 13.0 11.8 10.2 8.5 7.3 5.4 4.1 2.9 2.2 1.6 0 Table 2: Data Code for Backlight Current Level, Address 0-2. 2846.2008.03.1.1 IBLED (mA) Address ENS Rising Edges 35.0 20.0 30mA (Full Scale) 15.0 20mA (Full Scale) 10.0 5.0 0.0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Data Code Figure 2: Data Code for Address 0-2 vs. Backlight Current Level. The AAT2846 incorporates additional circuitry that optimizes performance for exceptionally low backlight current settings. A separate address is used to activate this circuitry. To program the low current settings with improved performance and efficiency, write to Address 3. Unlike Addresses 0-3, which have current level settings according to Table 2 and Figure 2, Address 3 possesses a separate set of current levels described by the Low Current Backlight settings found in Table 3. Data Main Current On Sub Current On Current (µA) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 No No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes No No No No Yes Yes Yes Yes No No No No Yes Yes Yes Yes 0 0 0 0 95 500 950 1900 95 500 950 1900 95 500 950 1900 Table 3: Data Code for Low-Level Backlight Current, Address 3, FS = 20mA range. www.analogictech.com 11 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Flash Current FL1, FL2 (Address 4) The current level for the flash channels FL1 and FL2 is programmed by Address 4. Data 1 enables the maximum current level. The maximum current level is determined by the value of RFSET. Table 4 and Figure 3 illustrate the additional flash current levels that are available. Data Flash LED Current (% of Maximum) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 100 87 77 66 58 50 44 39 35 30 27 24 20 17 16 14 IFLED (% of FL Maximum) IFLED = 100% at Data 1 80 60 IFLED = 14% at Data 16 FL2 Off Off On On Off On Off On Table 5: Output Enable Control, Address 5. There are two separate current level scales that apply to Addresses 0-2: 20mA and 30mA. According to the Maximum Backlight Current setting at Address 12, only one of the two scales can be active at any given time and never both. By default, the 20mA scale is active on startup. To change to the 30mA scale, or go back to the 20mA scale, write to Address 12. Since only one of the scales can be active at any given time, the 20mA and 30mA scales cannot be mixed between main and sub. When setting Address 12 to the 30mA scale, only current levels from that scale can be mixed between main and sub. 20 Data Maximum Current 0 1 2 20mA 30mA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Data Code Figure 3: Data Code for Address 4 vs. Percentage of Flash Current Level. Independent Flash ON/OFF Control (Address 5) Use Address 5 to program which flash channels are active. By default, both flash channels are OFF at startup. After writing to Address 4 to program the desired 12 FL1 1 2 3 4 Maximum Backlight Current (Address 12) 120 40 Data Writing to Address 5 enables the flash channels indefinitely. FL1 and FL2 will remain ON until Address 5 is re-programmed to OFF, ENS is strobed low to shutdown the device, or the flash safety timer times out after FEN has been strobed high. The flash safety timer is always activated when FEN is taken high. The Address 5 data setting is always reset to Data 1 when the flash timer expires or when FEN is strobed low. Table 4: Data Code for the Flash Current Control, Address 4. 100 flash channel current level, write to Address 5 to enable a single channel or both channels according to Table 5. Table 6: Data Code for the Maximum Current Settings, Address 12. Backlight Independent Channel Control (Address 15) The AAT2846 has a unique independent channel control mode whereby individual backlight LED channels can be enabled and disabled to form a custom arrangement of active channels. www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications To enable independent channel control mode, write Data 8 to Address 15. To exit individual mode control, the AAT2846 state machine can be reset by strobing ENS low and holding ENS low longer than the AS2Cwire’s tOFF latch time. Data Individual Backlight Control 8 On Table 7: Data Code for Independent Backlight Control, Address 15. With independent channel control mode enabled, Addresses 2 and 3 are re-mapped according to Tables 8 and 9. As indicated by the possible settings listed in the tables, any combination of backlighting channels can be enabled and disabled. Because Addresses 2 and 3 are re-mapped when independent channel control mode is enabled, the functions originally assigned to Addresses 2 and 3 are no longer available. It is also important to note that Address 0 is disabled when independent channel control mode is enabled. Additionally, Address 3 is disabled and the very low current settings cannot be used in this mode. Other addresses are unmodified by this mode so that the flash features can still be operated and the 30mA backlight scale can still be used. The LDO enables are always independent of AS2Cwire programming. Flash LED Current Control The flash LEDs are driven through current sinks FL1 and FL2. There are two ways to drive the flash LEDs: either through the AS2Cwire serial interface or through the flash enable input, FEN. The AAT2846 also includes an adjustable safety timer to turn off the flash in the event of a controller fault to prevent overstressing the flash LEDs. Flash/Movie Mode Operation The flash LED current level is set via the serial interface according to a logarithmic scale where each code is 1.2dB lower than the previous code as a percentage of the maximum current set by an external resistor, RFSET from FSET to AGND. Flash LED current is set between 2846.2008.03.1.1 14% and 100% of the maximum current for both channels through Address 4. For lower current applications such as torch, flashlight, or movie light, write to Address 5 to enable only FL1 or only FL2. For higher LED current, the flash channels can be connected in parallel to drive the sum of the two channel currents into a single LED. Data BL6 BL5 BL4 BL3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Off Off Off Off Off Off Off Off On On On On On On On On Off Off Off Off On On On On Off Off Off Off On On On On Off Off On On Off Off On On Off Off On On Off Off On On Off On Off On Off On Off On Off On Off On Off On Off On Table 8: Data Code for BL3-BL6 On/Off Control, Sub-Address 2. Data BL2 BL1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Off Off Off Off Off Off Off Off On On On On On On On On Off Off Off Off On On On On Off Off Off Off On On On On Table 9: Data Code for BL1 and BL2 On/Off Control, Sub-Address 3. www.analogictech.com 13 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Flash/Movie Mode Operation Flash Protection Timer The flash LED current level is set via the serial interface according to a logarithmic scale where each code is 1.2dB lower than the previous code as a percentage of the maximum current set by an external resistor, RFSET from FSET to AGND. Flash LED current is set between 14% and 100% of the maximum current for both channels through Address 4. For lower current applications such as torch, flashlight, or movie light, write to Address 5 to enable only FL1 or only FL2. For higher LED current, the flash channels can be connected in parallel to drive the sum of the two channel currents into a single LED. The AAT2846 includes a protection timer set by the capacitor CT connected from CT to AGND. The timer is used to avoid thermal issues with flash LEDs operating above their continuous power rating should a data error occur in the controller. The flash protection time, TF, is calculated by the following equation: where TF is in seconds and CT is in µF. For example: if CT = 0.1µF: Flash Strobe Input The AAT2846 features an active high flash enable input, FEN, that overrides the AS2Cwire programming and drives both flash outputs, FL1 and FL2, at the maximum current set by the flash current setting resistor RFSET. This signal also triggers an internal protection timer. When the FEN input is strobed low, the flash current is turned off independent of the internal timer. If FEN remains high at the end of the protection timer period, the flash LEDs are turned off. Make sure that the maximum time set by the external CT capacitor is such that the flash LEDs remain within their power dissipation limit at the maximum current set by RFSET. Contact the LED manufacturer for details on the thermal limitations of the LEDs used. When FEN is used to control the flash LEDs, flash on/off control set by Address 6 is automatically reset. 14 TF = 10 · CT TF = 10 · 0.1µF = 1s Low Dropout Regulators The AAT2846 includes two independent LDO linear regulators. The regulators operate from a 2.7V to 5.5V input voltage at IN. The AAT2846 supplies separate LDO enable inputs (ENA and ENB) to control individually the operation of the LDOs. The LDO output voltages are set through resistive voltage dividers from the output (OUTA or OUTB) to the feedback input (FBA or FBB). The regulator controls the output voltage such that the voltage divider output is at the 1.2V feedback threshold. The low 200mV dropout voltage at 200mA load current allows the regulator to maintain output voltage regulation. Each LDO regulator can supply up to 200mA continuous current to the load. They include current limiting and thermal overload protection to prevent damage to the load or to the LDOs. www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Applications Information Altering the Maximum Flash LED Current Level LDO Output Voltage Programming RFSET determines the maximum LED current level at each of the F1 and F2 flash LED outputs. In the typical application, selecting RFSET = 280K results in 300mA/ch LED current. From this reference point, the maximum current level can be modified by calculating an alternative RFSET value: The output voltages for LDOA and LDOB are programmed by an external resistor divider network. As shown below, the selection of R1 and R1 is a straight forward matter. R1 is chosen by considering the tradeoff between the feedback network bias current and resistor value. Higher resistor values allow stray capacitance to become a larger factor in circuit performance whereas lower resistor values increase bias current and decrease efficiency. OUT(A/B) RFSET = 300mA · 280kΩ ILED(MAX) This is illustrated in Figure 4. VOUT(A/B) 450 400 R2(A/B) 350 VREF(A/B) = 1.2V IFLED (mA) FB(A/B) R1(A/B) 300 250 200 150 100 50 To select appropriate resistor values, first choose R1 such that the feedback network bias current is less than 10µA. Then, according to the desired VOUT, calculate R1 according to the equation below. An example calculation follows. An R1 value of 120K is chosen, resulting in a small feedback network bias current of 1.2V/120K = 10µA. The desired output voltage is 1.8V. From this information, R1 is calculated from the equation below. R2 = R1(VOUT - 1.2V) 1.2V 0 100 R2 (Ω) 160K 130K 79.6K 60.4K 30.1K Table 10: Example Output Voltages and Corresponding Resistor Values 2846.2008.03.1.1 400 500 600 700 800 900 1000 1100 RFSET (kΩ Ω) Figure 4: Maximum Flash LED Current vs. RFSET. Selection of set resistor values outside of the typical application must be carefully evaluated to ensure that the application’s performance requirements can still be met. The AAT2846 power conversion efficiency depends on the charge pump mode. By definition, device efficiency is expressed as the output power delivered to the LEDs divided by the total input power consumed. η= R2 Standard 1% Values (R1 = 120K) 2.8 2.5 2.0 1.8 1.5 300 Device Power Efficiency The result is R1 = 60K. Since 60K is not a standard 1%-value, 60.4K is selected. From this example calculation, for VOUT = 1.8V, use R1 = 120K and R1 = 60.4K. Example output voltages and corresponding resistor values are provided in Table 11. VOUT (V) 200 POUT PIN When the input voltage is sufficiently greater than the LED forward voltages, the device optimizes efficiency by operating in 1X mode. In 1X mode, the device is working as a bypass switch and passing the input supply directly to the output. By simplifying the conditions such that the LEDs have uniform VF, the power conversion efficiency can be approximated by: www.analogictech.com 15 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications η= VF VF · ILED ≈ VIN · IIN VIN Due to the very low 1X mode quiescent current, the input current nearly equals the total output current delivered to the LEDs. Further, the low-resistance bypass switch introduces negligible voltage drop from input to output. The AAT2846 further maintains optimized performance and efficiency by detecting when the input voltage is not sufficient to sustain LED drive current. The device automatically switches to 1.5X mode when the input voltage drops too low in relation to the LED forward voltages. In 1.5X mode, the output voltage can be boosted to 3/2 the input voltage. The 3/2 conversion ratio introduces a corresponding 1/2 increase in input current. For ideal conversion, the 1.5X mode efficiency is given by: η= VF VF · ILED = VIN · 1.5IIN 1.5 · VIN Similarly, when the input falls further, such that 1.5X mode can no longer sustain LED drive current, the device will automatically switch to 2X mode. In 2X mode, the output voltage can be boosted to twice the input voltage. The doubling conversion ratio introduces a corresponding doubling of the input current. For ideal conversion, the 2X mode efficiency is given by: η= VF VF · ILED = VIN · 2IIN 2 · VIN LED Selection The AAT2846 is designed to drive high-intensity white LEDs. It is particularly suitable for LEDs with an operating forward voltage in the range of 1.5V to 4.2V. The charge pump can also drive other loads that have similar characteristics to white LEDs. For various load types, the AAT2846 provides a high-current, programmable ideal constant current source. Capacitor Selection Careful selection of the four external capacitors CIN, C1, C2, and COUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used. In general, low ESR may be defined as less than 100mΩ. 16 Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT2846. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is nonpolarized. Low ESR ceramic capacitors help maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Equivalent Series Resistance ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials Ceramic capacitors less than 0.1µF are typically made from NPO or C0G materials. NPO and C0G materials generally have tight tolerance and are very stable over temperature. Larger capacitor values are usually composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors are often available in lowercost dielectrics, but capacitors greater than 10µF are not typically required for AAT2846 applications. Capacitor area is another contributor to ESR. Capacitors that are physically larger will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit performance when compared to an equal value capacitor in a smaller package size. PCB Layout To achieve adequate electrical and thermal performance, careful attention must be given to the PCB layout. In the worst-case operating condition, the chip must dissipate considerable power at full load. Adequate heat-sinking must be achieved to ensure intended operation. Figure 5 illustrates an example PCB layout. The bottom of the package features an exposed metal paddle. The exposed paddle acts, thermally, to transfer heat from the chip and, electrically, as a ground connection. www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications The junction-to-ambient thermal resistance (θJA) for the connection can be significantly reduced by following a couple of important PCB design guidelines. The PCB area directly underneath the package should be plated so that the exposed paddle can be mated to the top layer PCB copper during the re-flow process. Multiple copper plated thru-holes should be used to electrically and thermally connect the top surface paddle area to additional ground plane(s) and/or the bottom layer ground pour. The chip ground is internally connected to both the paddle and to the AGND and PGND pins. It is good practice to connect the GND pins to the exposed paddle area with traces as shown in the example. The flying capacitors C1 and C2 should close to the IC. Trace length should be minimize path resistance and potential input and output capacitors should also close to the chip as possible. be connected kept short to coupling. The be placed as Evaluation Board User Interface The user interface for the AAT2846 evaluation board is provided through 4 buttons and a number of connection terminals. The board is operated by supplying external power and pressing individual buttons or button combinations. The table below indicates the function of each button or button combination. To power-on the board, connect a power supply or battery to the DC- and DC+ terminals. Make the board’s supply connection by positioning the J1 jumper to the ON position. A red LED indicates that power is applied. The evaluation board is made flexible so that the user can disconnect the enable lines from the microcontroller and apply external enable signals. By removing the jumpers from J2, J3, J4 and/or J5, external enable signals can be applied to the board. External enable signals must be applied to pin 1 of each J2, J3, J4 or J5 terminal. When applying external enable signals, consideration must be given to the voltage levels. The externally applied voltages cannot exceed the supply voltage that is applied to the IN pins of the device (DC+). The LDO loads can be connected directly to the evaluation board. For adequate performance, be sure to connect the load between OUTA/OUTB and DC- as opposed to some other GND in the system. Figure 5: Example PCB Layout. 2846.2008.03.1.1 www.analogictech.com 17 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Button(s) Pushed DATA LIGHT LIGHT+DATA MOVIE MOVIE+DATA FLASH FLASH+DATA LIGHT+MOVIE+FLASH Description Increment the data setting for the most recently activated mode. With backlight or movie mode activated, hold down the button to auto-cycle through the brightness levels. Toggle ON/OFF the backlighting section. Set the brightness level using the DATA button (defaults to Data 1). Decrement the brightness setting for backlight mode. Hold down to auto-cycle. Toggle ON/OFF movie mode illumination. Set the brightness level using the DATA button (defaults to Data 10). Decrement the brightness setting for movie mode. Hold down to auto-cycle. Generate a flash pulse. Pulse duration is the lesser of 2 seconds or the CT value result. Set the brightness level using the DATA button (defaults to Data 1). Toggle ON/OFF the LDOs. Reset. Clear all data and bring all enable lines low. Table 11: AAT2846 Evaluation Board User Interface. Evaluation Board Layout Figure 6: AAT2846 Evaluation Board Layout Top Side. 18 Figure 7: AAT2846 Evaluation Board Layout Bottom Side. www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Evaluation Board Schematics VOUT DC+ D1 D2 D3 D4 D5 D6 D7 D8 VIN J1 1 2 C12 100µF 3 280K yields 300mA/chnl max flash optional 100µF lab supply bypass R10 280K 22 23 24 25 26 U1 F1 FEN D6 FSET D5 ENA D4 ENFL 27 28 ENLA 1 2 3 4 5 6 7 ENS D1 PGND AGND IN C2- CREF C2+ FBB ENB 21 20 ENBL 19 18 17 16 C2 1.0µF C4 4.7µF 15 OUT C1- 9 C1+ IN 8 OUTA CT FBA C9 0.1µF C8 0.1µF F2 D2 OUTB CTRL _CT D3 ENLB 10 11 12 13 14 VOUT OUTB Programmed for 2.8V output by default R11 160K C6 2.2µF C5 2.2µF C3 2.2µF C1 1.0µF R12 120K R13 60.4K R14 120K C7 2.2µF OUTA Programmed for 1.8V output by default Figure 8: AAT2846 Section Schematic. 2846.2008.03.1.1 www.analogictech.com 19 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications U3 AAT4290 VIN C11 0.1µF 1 2 3 4 IN OUT3 OUT2 OUT4 OUT1 OUT5 EN/SET GND 8 7 6 5 J2 ENBL J3 ENFL J4 ENLA J5 ENLB ENBL ENFL ENLA ENLB R6 R7 R8 R9 100K 100K 100K 100K VIN VIN R1 1K DATA SW1 LIGHT SW2 MOVIE SW3 FLASH SW4 R2 1K R3 1K R4 1K U2 1 2 3 4 VDD GP5 GP4 GP3 VSS GP0 GP1 GP2 8 7 6 5 C10 0.1µF R5 330 LED7 RED PIC12F675 CTRL_CT DC- Figure 9: MCU and I/O Expander Section Schematic. Evaluation Board Component Listing 20 Component Part# Description Manufacturer U1 AAT2846INJ-EE-T1 High Eff. 1X/1.5X/2X CP for White LED, Dual LDO AnalogicTech U2 U3 D1-D6 D7, D8 C1, C2 C3-C7 C4 C8-C11 C12 R1-R4 R5 R6-R9 R10 R11 R12, R14 R13 J1-J5 LED7 SW1-SW4 PIC12F675 AAT4290IJS-1-T1 LW M673 LXCL-PWF1 GRM18x GRM18x GRM18x GRM18x TAJBx Chip Resistor Chip Resistor Chip Resistor Chip Resistor Chip Resistor Chip Resistor Chip Resistor PRPN401PAEN CMD15-21SRC/TR8 PTS645TL50 8-bit CMOS, FLASH MCU; 8-pin PDIP I/O Expander Mini TOPLED White LED; SMT Luxeon Flash LED 1.0µF, 10V, X5R, 0603, Ceramic 2.2µF, 10V, X5R, 0603, Ceramic 4.7µF, 10V, X5R, 0603, Ceramic 0.1µF, 16V, X7R, 0603, Ceramic 100µF, 10V, 10µA, Tantalum 1K, 5%, 1/4W; 1206 330, 5%, 1/4W; 1206 100K, 5%, 1/10W; 0603 280K, 1%, 1/10W; 0603 160K, 1%, 1/10W; 0603 120K, 1%, 1/10W; 0603 60.4K, 1%, 1/10W; 0603 Conn. Header, 2mm Zip Red LED; 1206 Switch Tact, SPST, 5mm Microchip AnalogicTech OSRAM Lumileds Murata Murata Murata Murata AVX Vishay Vishay Vishay Vishay Vishay Vishay Vishay Sullins Electronics Chicago Miniature Lamp ITT Industries www.analogictech.com 2846.2008.03.1.1 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Ordering Information Package Marking1 Part Number (Tape and Reel)2 TQFN44-28-0.4 UPXYY AAT2846INJ-EE-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/about/quality.aspx. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 2846.2008.03.1.1 www.analogictech.com 21 PRODUCT DATASHEET AAT2846 ChargePumpTM High Current Charge Pump with Dual LDO for Backlight and Flash Applications Package Information1 TQFN44-28-0.4 Pin 1 Dot by Marking C0.3 2.600 ± 0.050 4.000 ± 0.050 Detail "A" 4.000 ± 0.050 2.600 ± 0.050 Top View Bottom View 0.400 ± 0.050 0.430 ± 0.050 0.750 ± 0.050 0.230 ± 0.050 0.203 REF 0.050 ± 0.050 Side View Pin 1 Indicator Detail "A" All dimensions in millimeters. 1. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737-4600 Fax (408) 737-4611 © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech’s terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. 22 www.analogictech.com 2846.2008.03.1.1