AAT4295/97 Single/Dual RGB Controller General Description Features The AAT4295/97 SmartSwitch is a member of AnalogicTech's Application Specific Power MOSFET™ (ASPM™) product family. The AAT4295/97 is comprised of three/six low-side N-channel MOSFET switches that gate an applied load to ground. This device is intended for controlling RGB fashion lighting in portable products; it can also be used for a combination of general purposes where a load requires a low-side switch connection to ground. The AAT4295/97 simplifies design and layout limitations by eliminating the need for multiple GPIO control lines and discrete MOSFETs to control product features. • • • • • • • • The state of each output channel is controlled with a single GPIO line via the EN/SET pin using AnalogicTech's Simple Serial Control™ (S2Cwire™) interface. After a short set of data pulses is sent to the EN/SET input and the line is pulled to logic high, the device is enabled with the desired switch configuration. In the enabled state, the AAT4295/97 typically consumes less than 3µA of quiescent current. When EN/SET is pulled to a logic low, the device is disabled and each output switch is placed in a high impedance open state. SmartSwitch™ Input Voltage Range: 1.8V to 5.5V Independent Low-Side N-Channel MOSFET Switches: — AAT4295: Three Channels — AAT4297: Six Channels User-Programmable S2Cwire Interface Single GPIO Controls State of Each MOSFET Low Quiescent Current: 3µA Typical Temperature Range: -40°C to +85°C No External Components Required Available in Pb-Free Packages — AAT4295 in 8-Pin SC70JW — AAT4297 in 12-Pin TSOPJW Applications • • • • Cell Phones Multiple Low Power Switching Personal Communication Devices Portable Electronic Devices The AAT4295 and AAT4297 operate over an input voltage range of 1.8V to 5.5V, making them ideal for battery-powered applications. The three-switch AAT4295 is offered in a Pb-free, 8-pin SC70JW package, while the six-switch AAT4297 is offered in a Pb-free, 12-pin TSOPJW package. Both devices are rated over the -40°C to +85°C temperature range. Typical Application VCC VCC AAT4295/97 S1 D1 D2 D3 *D4 *D5 *D6 RB1 RB2 RB3 RB4 RB5 RB6 S2 S3 EN/SET EN/SET *S4 *S5 GND *S6 * AAT4297 Only 4295.2006.03.1.3 1 AAT4295/97 Single/Dual RGB Controller Pin Descriptions Pin Number AAT4295 AAT4297 Symbol Function 1 8 VCC Input supply voltage. 2, 3 9, 10, 12 N/C No connection. 4 11 EN/SET 5 1 GND 6 2 S1 Drain of the N-channel MOSFET for Channel 1. 7 3 S2 Drain of the N-channel MOSFET for Channel 2. 8 6 S3 Drain of the N-channel MOSFET for Channel 3. N/A 4 S5 Drain of the N-channel MOSFET for Channel 5. N/A 5 S4 Drain of the N-channel MOSFET for Channel 4. N/A 7 S6 Drain of the N-channel MOSFET for Channel 6. Input control pin using S2Cwire serial interface. The device records rising edges of the clock and decodes them into eight states, which control the ON/OFF states of the MOSFETs. See Table 1 for output settings. In addition, a logic low forces the device into shutdown mode, reducing the supply current to less than 1µA. This pin should not be left floating. Ground connection. Pin Configuration AAT4295 SC70JW-8 (Top View) VCC N/C N/C EN/SET 2 1 8 2 7 3 6 4 5 AAT4297 TSOPJW-12 (Top View) S3 S2 S1 GND GND S1 S2 S5 S4 S3 1 12 2 11 3 10 4 9 5 8 6 7 N/C EN/SET N/C N/C VCC S6 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Absolute Maximum Ratings1 Symbol VCC to GND INx to GND EN/SET TJ Description Power Supply to GND All Input (Drain) to GND EN/SET to GND Operating Junction Temperature Range Value Units 6.0 -0.3 to 6.0 -0.3 to 6.0 -40 to 150 V V V °C Value Units Thermal Information2 Symbol Description θJA Thermal Resistance PD Maximum Power Dissipation SC70JW TSOPJW SC70JW TSOPJW 225 160 4403 6254 °C/W mW 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 board. 3. Derated 4.4mW/°C above 25°C. 4. Derated 6.25mW/°C above 25°C. 4295.2006.03.1.3 3 AAT4295/97 Single/Dual RGB Controller Electrical Characteristics1 VCC = 5.0V; TA = -40°C to +85°C, unless otherwise noted. Typical values are TA = 25°C. Symbol VCC IQ IQ(OFF) Description Supply Voltage Range Quiescent Current IDS(OFF) Off Supply Current Off Switch Current for Any Switch RDS(ON) On-Resistance TCRDS TON EN/SET VEN(L) VEN(H) TEN/SET LO TEN/SET_HI_MIN TEN/SET_HI_MAX TOFF TLAT IEN/SET Conditions On-Resistance Temperature Coefficient Output Turn-On Time2 Min Typ 1.8 VCC = 5V, EN/SET = VCC, IOUT = No Load, All Switches On EN/SET = 0, VCC = 5V, VOUT Open 3.0 Max Units 5.5 V 10 µA 1.0 µA EN/SET = 0, VCC = 5V, VOUT = 0 0.1 1.0 µA VCC = 5V VCC = 3.6V 1.9 2.1 6.0 7.0 Ω 2800 VIN = 5V, RPULLUP = 250Ω, COUT = 0.1µF Enable Threshold Low VIN = 1.8V Enable Threshold High VIN = 5.5V EN/SET Low Time Minimum EN/SET High Time Maximum EN/SET High Time EN/SET Off Timeout EN/SET Latch Timeout EN/SET Input Leakage 0.6 1.4 0.5 ppm/°C 2.7 µs 0.3 V V µs ns µs µs µs µA 75 50 -1 75 500 500 1 1. The AAT4295 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. TON is the time after latch timeout to 10% of the output voltage. See Figure 1, Timing Diagram. 4 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Typical Characteristics Quiescent Current vs. Input Voltage Quiescent Current vs. Temperature 3.0 3.0 Quiescent Current (µA) Quiescent Current (µ µA) 3.5 85°C 2.5 2.0 1.5 -40°C 25°C 1.0 0.5 0.0 1.5 2 2.5 3 3.5 4 4.5 5 2.0 1.5 1.0 -40 5.5 VIN = 5V 2.5 VIN = 3.6V -20 0 20 40 60 Input Voltage (V) Temperature (°°C) Off-Supply Current vs. Temperature RDS(ON) vs. Input Voltage 80 100 (ILOAD = 20mA) 3.5 VIN = 5V 0.005 0.004 3.0 VIN = 4.2V RDS(ON) (Ω Ω) Quiescent Current (µA) 0.006 VIN = 3.3V 0.003 0.002 0.001 0 20 40 60 80 100 RDS1 RDS5 2.0 RDS2 2.5 3.0 3.5 4.0 4.5 Input Voltage (V) RDS(ON) vs. Temperature RDS(ON) vs. Temperature (VIN = 3.6V; ILOAD = 20mA) (VIN = 5V; ILOAD = 20mA) 5.0 5.5 3.0 2.5 RDS4 RDS3 RDS6 RDS(ON) (Ω) RDS(ON) (Ω) RDS6 Temperature (°°C) 3.0 2.0 1.5 1.0 RDS4 2.0 1.0 1.5 0.000 -20 2.5 1.5 VIN = 1.8V -40 RDS3 RDS5 -40 -20 0 RDS2 RDS1 20 40 RDS6 2.0 1.5 60 80 100 RDS4 RDS3 RDS2 RDS5 Temperature (°°C) 4295.2006.03.1.3 2.5 1.0 -40 -20 0 20 RDS1 40 60 80 100 Temperature (°°C) 5 AAT4295/97 Single/Dual RGB Controller Typical Characteristics EN/SET Latch Timeout vs. Input Voltage EN/SET Timeout vs. Input Voltage 300 250 Latch Timeout, TLAT (µs) TOFF 225 Timeout (µs) 200 175 TLATCH 150 125 100 75 50 1.5 2 2.5 3 3.5 4 4.5 5 5.5 -40°C 250 200 150 85°C 25°C 100 50 1.5 Input Voltage (V) 2 2.5 3 3.5 4 4.5 5 5.5 Input Voltage (V) Turn-On Characteristic EN/SET Off Timeout vs. Input Voltage (IOUT1 = IOUT2 = 20mA) Off Timeout, TOFF (µs) 300 -40°C 250 EN/SET (5V/div) 200 150 VOUT1 (5V/div) VOUT2 (5V/div) 85°C 25°C 100 IOUT1 (20mA/div) 50 1.5 2 2.5 3 3.5 4 5 5.5 Input Voltage (V) Time (50µs/div) Turn-On Characteristic Turn-Off Characteristic (IOUT1 = IOUT2 = 20mA) (IOUT1 = IOUT2 = 20mA) EN/SET (5V/div) EN/SET (5V/div) VOUT1 (5V/div) VOUT1 (5V/div) VOUT2 (5V/div) VOUT2 (5V/div) IOUT1 (20mA/div) IOUT1 (20mA/div) Time (50µs/div) 6 4.5 Time (50µs/div) 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Typical Characteristics Transition of Outputs Turn-On Transient Characteristic (IOUT1 = IOUT2 = 20mA) (IOUT1 = IOUT2 = 20mA) EN/SET (5V/div) EN/SET (5V/div) VOUT1 (20mV/div, AC coupled) VOUT1 (5V/div) VOUT2 (5V/div) VOUT2 (5V/div) IOUT1 (20mA/div) IOUT1 (20mA/div) Time (50µs/div) Time (50µs/div) Turn-Off Transient Characteristic Turn-On Fall Time vs. Temperature (IOUT1 = IOUT2 = 20mA) 1.0 0.8 VOUT1 (20mV/div, AC coupled) 0.6 Time (µs) EN/SET (5V/div) VOUT2 (5V/div) IOUT1 (20mA/div) TON (Fall Time) 0.4 0.2 0.0 -40 -20 0 Time (50µs/div) 40 60 80 100 Temperature (°°C) VIH vs. Input Voltage VIL vs. Input Voltage 1.1 1.0 1.0 0.9 -40°C -40°C 0.8 VIL (V) 0.9 VIH (V) 20 0.8 0.7 85°C 25°C 0.7 0.6 85°C 25°C 0.5 0.6 0.4 0.5 0.3 1.5 2.0 2.5 3.0 3.5 4.0 Input Voltage (V) 4295.2006.03.1.3 4.5 5.0 5.5 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) 7 AAT4295/97 Single/Dual RGB Controller Functional Block Diagram EN/SET S2 Cwire Interface VCC Control Logic S1 S2 S3 S4* S5* S6* GND * AAT4297 only Functional Description The AAT4295/97 is comprised of three or six lowside N-channel MOSFET load switches primarily targeted for general purpose applications where several load circuits need to be connected to a common ground and controlled from a single microcontroller GPIO output. When a given switch is enabled, the respective switch connects the load input (S1 to S3 for the AAT4295 and S1 to S6 for the AAT4297) to ground through the N-channel MOSFET. Each low-side N-channel MOSFET transistor has a typical on resistance (RDS(ON)) of 2Ω when operating from a 3.6V supply. Both the AAT4295 8 and AAT4297 have been designed to operate with an input voltage range of 1.8V to 5.5V, making them ideal for battery-powered applications. These devices may be used for load switching applications such as RGB LED fashion lighting, display or keypad backlight LEDs, miscellaneous indicator LED lamps, as well as audio and RF circuits or any other system with a power requirement that does not exceed the thermal dissipation limits of the load switch and device package. Each switch input may be represented by the following circuit (Figure 1) and simplified equivalent model (Figure 2). 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Control S1 to S6 Control 2Ω S1 to S6 Figure 1: Switch Input Circuit. The state of each switch is controlled via the EN/SET pin using AnalogicTech's S2Cwire interface. To enable a respective switch, a series of clocked pulses should be applied to the EN/SET pin. The number of pulses clocked will determine the switch configuration based on the truth table given in Table 1. At the end of the serial pulse data set, the EN/SET set pin should be held high to latch the clocked data and enable the desired switch configuration. When the device is enabled with the EN/SET held to a logic high state, the quiescent current consumption will typically increase to 3µA at normal ambient room temperatures. If output sequencing of the switches is not necessary, all of the switches may be turned on simultaneously on the first rising edge of the EN/SET pin by simply pulling the EN/SET to a logic high level. The default configuration for one clock pulse is to enable all switches to the "on" state. However, if output sequencing is desired, a series of pulses on the EN/SET pin will set the outputs to the desired state (refer to Table 2 for output settings). For LED lighting applications, the EN/SET line may be clocked at rates up to 1MHz, allowing the user to not only control brightness, but (in the case of color RGB LEDs) color as well. 4295.2006.03.1.3 Figure 2: Simplified Equivalent Model. Output Settings The ON/OFF state of the MOSFET switches is controlled by the EN/SET serial data input. An internal control counter is clocked on the rising edge of the EN/SET pin, and is decoded into the 8 possible states of the MOSFET for the AAT4295 (see Table 1) and 64 possible states for the AAT4297 (see Table 2). The counter rolls over after 8 clocks and the table repeats. Clock OUT3 OUT2 OUT1 1 2 3 4 5 6 7 8 on on on on off off off off on on off off on on off off on off on off on off on off Table 1: AAT4295 EN/SET Settings. 9 AAT4295/97 Single/Dual RGB Controller AAT4297 AAT4297 AAT4295 (only) Clock OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on off off off off off off off off off off off off off off off off on on on on on on on on off off off off off off off off on on on on on on on on off off off off off off off off on on on on off off off off on on on on off off off off on on on on off off off off on on on on off off off off on on off off on on off off on on off off on on off off on on off off on on off off on on off off on on off off on off on off on off on off on off on off on off on off on off on off on off on off on off on off on off on off Clock 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off off on on on on on on on on on on on on on on on on off off off off off off off off off off off off off off off off on on on on on on on on off off off off off off off off on on on on on on on on off off off off off off off off on on on on off off off off on on on on off off off off on on on on off off off off on on on on off off off off on on off off on on off off on on off off on on off off on on off off on on off off on on off off on on off off on off on off on off on off on off on off on off on off on off on off on off on off on off on off on off on off Table 2: Output Settings. The S2Cwire interface relies on the number of rising edges of the EN/SET pin to load the internal register to a desired count. S2Cwire control latches data after the EN/SET pin has been held high for the preset latch enable time (TLAT). The interface records rising edges of the EN/SET pin and decodes them into one of 8 states for the AAT4295 or to one of 64 states for the AAT4297, as indicated in Tables 1 and 2. The counter can be clocked at speeds up to 1MHz, so different switch combi10 nations may be clocked in lighting applications without any visible perception to the user. Alternatively, the EN/SET clock pulses may be entered one at a time for the desired setting. The first rising edge of EN/SET enables the IC and turns all the switches ON. Once the final clock cycle is received, the EN/SET pin is held high to maintain the device setting. The device is disabled 500µs (TOFF) after the EN/SET pin transitions to a logic low state (see Figure 3). 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Sn TH TL TLAT TON TO T OFF EN/SET Figure 3: EN/SET Timing Diagram. Application Information External Component Selection The AAT4295 and AAT4297 have been designed so that no external parts are required for the device to function as a general purpose three- or six-position low-side switch. For some applications, the addition of bypass capacitors or pull-up or pulldown resistors may be desired to improve overall system performance. For lighting applications, such as controlling RGB LEDs, keypad or display backlight LEDs, or photo flash LEDs, no bypass capacitors are necessary. For other general purpose load switching applications which may use some or all of the outputs to switch light load current levels to application circuits, good engineering practice would dictate the use of small bypass capacitors placed on the VCC input and each switch connection that is used to conduct current from the load to ground. The use of small ceramic capacitors between the input and output nodes will aid in reducing line and load transient response effects when the load switch on a given output is turned on or off. Input Capacitor Typically, a 0.1µF capacitor is recommended for CIN in most applications to provide input line transient response immunity to small changes in the input supply. A CIN capacitor is not required for basic operation. If used, CIN should be located as close to the device VIN pin as practically possible. There is no specific capacitor equivalent series resistance (ESR) requirement for CIN; however, for higher current operation, ceramic capacitors are recommended for CIN due to their inherent capability over tantalum or aluminum electrolytic capacitors to withstand input current surges from low impedance sources, such as batteries in portable devices. 4295.2006.03.1.3 Output Capacitor For typical applications where the AAT4295/97 is used for LED lighting control, no output capacitors are required because the end load is not sensitive to device turn-on or turn-off transient effects. For improved load transient response in systems using the AAT4295/97 for load switching, the addition of a small output capacitor placed between the output pins and ground can have a beneficial effect. A 0.1µF ceramic capacitor is suggested as a reasonable value for an output capacitor. The output capacitor has no specific capacitor type or ESR requirement. If desired, COUT may be increased to a value greater than 0.1µF without limit to accommodate any load transient condition without adversely affecting the device turn-on slew rate time. Thermal Considerations The AAT4295 and AAT4297 are designed to sink a continuous load current to ground when a respective switch is enabled via the S2Cwire control. The limiting characteristic for maximum safe operating load current through a given switch or set of switches is package power dissipation. In order to obtain high operating currents, careful device layout and circuit operating conditions must be taken into account. At any given ambient temperature (TA), the maximum package power dissipation can be determined by the following equation: PD(MAX) = TJ(MAX) - TA θJA Constants for the AAT4295 are maximum junction temperature, TJ(MAX) = 125°C, and package thermal resistance, θJA = 225°C/W. Worst case conditions are calculated at the maximum operating tempera11 AAT4295/97 Single/Dual RGB Controller ture, where TA = 85°C. Typical conditions are calculated under normal ambient conditions, where TA = 25°C. At 25°C ambient, the AAT4295 is capable of dissipating 444.4mW of power and the AAT4297 is capable of dissipating 625mW of power. At 85°C ambient, the AAT4295 is capable of dissipating 177.8mW of power and the AAT4297 can dissipate 250mW. The power dissipation of any given MOSFET switch is limited by its respective on resistance (RDS). The RDS of any given MOSFET switch is controlled by the applied gate voltage to the switch, which is set by the applied VCC supply and the ambient operating temperature. Switch RDS for the AAT4295 or AAT4297 may be estimated by using the RDS versus Temperature curve in the Typical Characteristics section of this datasheet. The maximum current of any given switch can be calculated for a given operating temperature and VCC supply level. The corresponding RDS is determined by use of the RDS vs. Temperature curve for the given VCC. Given the maximum package power dissipation and operating temperature, the maximum current through any switch or combination of switches can be calculated using the following formula: 1 ⎛ PD(MAX)⎞ 2 ISWITCH(MAX) = ⎝ R ⎠ DS Example: If all the switches on an AAT4295 were closed simultaneously, each switch could handle up to 271mA of current at 25°C for total of 813mA. For the same set of operating conditions at 25°C, the AAT4297 can handle up to 208mA per switch for a total of 1.25A for all six switches. If the load current for a desired application exceeds the recommended current at a given temperature, two or more switches may be operated in parallel as long as the overall power dissipation of the device package is not exceeded. If different current levels are passed through different switches on a given device, then one should total up the power dissipation for each switch and assure the sum of the power dissipation does not exceed the power rating for the package. Application Circuits Today, many mobile phones and similar products contain RGB LED fashion lighting, LCD display and sub-display, as well as keypad backlighting and photo flash LEDs. Due to the nature of common anode RGB LEDs, the AAT4295 and AAT4297 make ideal low-cost lighting control solutions. In general, most types of LEDs can be controlled via a low-side MOSFET switch and current limiting ballast resistor. The following application circuits (Figures 4 through 7) show voltage boosting charge pumps to power RGB and flash LEDs. However, if a voltage or current source is already available in a given product design, the charge pump circuit block may be replaced with the existing power source solution. Since both the AAT4295 and AAT4297 require only one GPIO line from the system microcontroller to enable and disable all the switches via the EN/SET input, these solutions can provide a simple way to add lighting solutions to existing design platforms. Driving LED Loads When driving LEDs with a voltage source, series ballast resistors must be used to limit the LED forward current. The LED current will vary with supply voltage and LED forward voltage. Most types of LEDs have forward voltage specifications ranging from 2.0V to 5.0V. When controlling an LED of any type with a low-side MOSFET switch, the necessary series ballast resistor value can be calculated from the following formula: RBALLAST = (VIN - VF) - RDS(ON) ILED Where: RBALLAST is the value of resistor to be placed in series with the LED (Ω). VIN is the input supply voltage to the device (V). VF is the forward voltage of the LED (V). RDS(ON) is the resistance of the switch when it is turned on (Ω). ILED is the desired operating current of the LED (A). 12 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller RGB LED VIN Li-Ion Battery 2.8V - 4.2V VOUT AAT3110 10µF VCC 10µF R RR 1µF SHDN GND B AAT4295 C+ CP ON/OFF G RG RB S1 C- S2 S3 EN/SET DATA EN/SET GND Figure 4: Single RGB LED Fashion Light Solution Using an AAT4295. RGB LED VIN Li-Ion Battery 2.8V - 4.2V 10µF 10µF AAT3110 R1 VCC VOUT AAT4297 EN/SET DATA SHDN GND RG1 RB1 B1 R2 RR2 RG2 G2 B2 RB2 S1 C+ S2 1µF CP ON/OFF RR1 G1 RGB LED S3 C- S4 EN/SET S5 S6 GND Figure 5: Dual RGB LED Fashion Light Solution Using an AAT4297. 4295.2006.03.1.3 13 AAT4295/97 Single/Dual RGB Controller VOUT1 VOUT2 VIN Li-Ion Battery 2.8V - 4.2V VCC C1+ 1µF AAT3112 10µF RGB LED 10µF VIN R1 AAT4297 C1- EN2 GND Flash RB1 RLIGHT S2 1µF EN1 Flash Enable R G1 B1 S1 C2+ RGB/Light Enable RR1 G1 Flash LED R FLASH S3 C2- S4 EN/SET DATA S5 EN/SET S6 GND Figure 6: RGB LED Fashion Light With a Dual Mode Light/Strobe Flash LED Solution Using an AAT4297. Input Voltage Supply RGB LED VCC R AAT4297 RR G RG B RB Main Display Sub Display Flash LED D1 D2 D3 D4 D5 D6 Flash RD1 RD2 RD3 R D4 RD5 RD6 RFLASH S1 S2 S3 S4 EN/SET DATA EN/SET S5 S6 GND Figure 7: Total Lighting Control Solution Using an AAT4297. Includes RGB Fashion Light, Main Display and Sub-Display LCD Backlight, and Photo Flash LED. 14 4295.2006.03.1.3 AAT4295/97 Single/Dual RGB Controller Ordering Information Package Marking1 Part Number (Tape and Reel)2 SC70JW-8 RBXYY AAT4295IJS-T1 TSOPJW-12 RCXYY AAT4297ITP-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. Package Information SC70JW-8 2.20 ± 0.20 1.75 ± 0.10 0.50 BSC 0.50 BSC 0.50 BSC 0.225 ± 0.075 2.00 ± 0.20 0.100 7° ± 3° 0.45 ± 0.10 4° ± 4° 0.05 ± 0.05 0.15 ± 0.05 1.10 MAX 0.85 ± 0.15 0.048REF 2.10 ± 0.30 All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 4295.2006.03.1.3 15 AAT4295/97 Single/Dual RGB Controller TSOPJW-12 2.85 ± 0.20 2.40 ± 0.10 0.10 0.20 +- 0.05 0.50 BSC 0.50 BSC 0.50 BSC 0.50 BSC 0.50 BSC 7° NOM 0.04 REF 0.055 ± 0.045 0.15 ± 0.05 + 0.10 1.00 - 0.065 0.9625 ± 0.0375 3.00 ± 0.10 4° ± 4° 0.45 ± 0.15 0.010 2.75 ± 0.25 All dimensions in millimeters. © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech’s standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 16 4295.2006.03.1.3