ANPEC APL1431LABC-TBL

APL1431L
Low Voltage Adjustable Precision Shunt Regulator
Features
General Description
•
•
The APL1431L is a 3-terminal low voltage adjustable precision reference with specified thermal stability over applicable commercial temperature ranges
. Output voltage may be set to any value between
VREF (1.24 V) and 20 V with two external resistors
(see Figure 2) . When used with an photocoupler ,
the APL1431L is an ideal voltage reference in isolated feedback circuits for 1.24V to 12V switchingmode power supplies . This device has a typical
output impedance of 0.1Ω . Active output circuitry
provides a very sharp turn-on characteristic , making the APL1431L excellent replacements for zener
diodes in many applications , including on-board
regulation and adjustable power supplies .
Precise Reference Voltage to 1.24V
Guaranteed 0.5% or 1% Reference Voltage
Tolerance
•
•
•
•
Sink Current Capability , 60mA to 100mA
Quick Turn-on
Adjustable Output Voltage , VO = VREF to 20V
Low Operational Cathode Current , 60mA
Typical
•
•
0.1Ω Typical Output Impedance
SOT-23-5 Packages
Applications
•
•
•
AN O DE
RE F
5
4
Linear Regulators
Adjustable Power Supply
Switching Power Supply
Symbol
1
2
3
NC
NC
C A T H O DE
Functional Diagram
REF
Anode
C athode
Cathode
+
R EF
−
V REF
Anode
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
1
www.anpec.com.tw
APL1431L
Ordering and Marking Information
Elec. Grade
A : 0.5% Reference Voltage Tolerance
B : 1% Reference Voltage Tolerance
Package Code
B : SOT- 23 - 5
Temp. Range
C : 0 to 70 C
I : -40 to 85 C
Handling Code
PB : Plastic Bag
TB : Tape & Box
TR : Tape & Reel
Lead Free Code
L : Lead Free Device
Blank : Original Device
APL1431L
Lead Free Code
Handling Code
Temp. Range
Package Code
Elec. Grade
APL1431L B :
1431L
Absolute Maximum Ratings
Symbol
VKA
IK
IREF
Rating
Unit
Cathode Voltage
Parameter
20
V
Continuous Cathode Current
100
mA
3
mA
Reference Current
Thermal Resistance from Junction to Ambient in Free Air
SOT-23-5
Operating Junction Temperature Range
357
°C/W
-40 to 150
°C
TSTG
Storage Temperature Range
-65 to 150
°C
TSOL
Lead Temperature Range, Ts (Soldering, 10sec)
260
°C
θJA
TJ
Electrical Characteristics
Symbol
Parameter
TA= 25°C ( unless otherwise noted)
Test Conditions
VKA=VREF, IK=10mA
TA= 25°C, (Fig. 1)
APL1431LA
APL1431LB
APL1431LA
APL1431LB
VREF
Reference Voltage
VDEV
VDEF Temp Deviation
∆VREF
/∆VKA
Ratio of Change in VREF
to Change in Cathode
IK=10mA, ∆VKA =16V to VREF (Fig. 2)
Voltage
Reference Input Current IK=10mA, R1=10kΩ, R2=∞ (Fig. 2)
IREF
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
TA= full range
(see Note 1), (Fig. 1)
TA= full range(see Note 1),
VKA =VREF , IK =10mA, (Fig. 1)
2
APL1431L
Min. Typ. Max.
1.234 1.240 1.246
1.228 1.240 1.252
1.222 1.240 1.258
1.215 1.240 1.265
Unit
V
5
15
mV
-0.2
-1.0
mV/V
0.15
0.5
µA
www.anpec.com.tw
APL1431L
Electrical Characteristics
Symbol
IREF(DEV)
IK(off)
ZKA
IK(MIN)
Parameter
TA= 25°C ( unless otherwise noted)
Test Conditions
APL1431L
Min.
Typ.
Max.
Unit
0.05
0.3
µA
0.01
0.01
0.1
0.5
µA
0.1
0.3
Ω
60
80
µA
TA= full range(see Note 1), R1=10kΩ,
R2=∞ , IK=10mA, (Fig. 2)
VK=6V
Off-state cathode current VREF=0V, (Fig. 3)
VK=16V
Dynamic Output
VKA =VREF , IK=100µA to 100mA ,
Impedance
f<1kHz , (Fig. 1 )
Minimum Operating
VKA =VREF , (Fig. 1)
Current
IREF Temp Deviation
Note : 1. Full temperature range is 0°C to 70°C for APL1431LXXC, and –40°C to 85°C for APL1431LXXI.
Test Circuits
V IN
VO
V IN
IK
V
VO
R1
I REF
R2
V REF
REF
Figure 1. Test Circuit for VKA=VREF, VO=VKA=VREF
IK
Figure 2. Test Circuit for VKA>VREF,
VO= VKA= VREF× (1+R1/R2) + IREF × R1
V IN
VO
IK(OFF)
Figure 3. Test Circuit for IK(OFF)
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
3
www.anpec.com.tw
APL1431L
Application Schematic
RB
V IN
VO
R1
0.1µF
V REF
APL431L
R2
GND
Precision Voltage Reference
V IN
VO
RB
R1
VREF
APL431L
0.1µF
R2
Precision Voltage Regulator
Notes for Application Circuits:
1)
2)
3)
•
•
To improve the stability of output voltage , a 0.1µF capacitor between cathode and anode of APL431L
is strongly recommended.
Set VO according to the following equation:
VO= VREF (1+R1/ R2)+ IREF R1
Choose the value for RB as follows:
The maximum limit for RB should be such that the cathode current( IK) is greater than the minimum
operating current (60µA) at VIN (MIN) .
The minimum limit for RB should be such that the cathode current (IK) does not exceed 100mA under
all load conditions, and the instantaneous turn-on value for IK does not exceed 150mA . Both of the
following conditions must be met :
RB,MIN ≥ VIN(MAX) / 150mA ( to limit instantaneous turn-on IK)
RB,MIN ≥ VIN(MAX) - VO / IO (MIN) + 100mA (to limit IK under normal operating conditions)
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
4
www.anpec.com.tw
APL1431L
Typical Characteristics
150
300
TA=25°C
TA=25°C
100
VKA=VREF
Cathode Current (mA)
Cathode Current (µA)
200
100
0
-100
-200
-300
VKA=VREF
50
0
-50
-100
-150
-1
-0.5
0
0.5
1
1.5
-1.5
-1
Cathode Voltage (V)
IK=10mA
Reference Input Current (nA)
Reference Voltage (V)
0.5
1
1.5
150
1.244
1.242
1.24
1.238
1.236
1.234
-40
0
Cathode Voltage (V)
1.248
1.246
-0.5
-20
0
20
40
60
80
R1=10kΩ
125
R2=∞
100
75
50
-40
100
Junction Temperature (°C)
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
IK=10mA
-20
0
20
40
60
80
100
Junction Temperature (°C)
5
www.anpec.com.tw
APL1431L
250
1.2
1.1
IK=10mA
1
Off State Cathode Current (nA)
Ratio of Delta Reference Voltage to Delta
Cathode Voltage (-mV/V)
Typical Characteristics (Cont.)
∆VKA=16V to VREF
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
VREF=0V
VKA=16V
200
150
100
50
0
-40
-20
0
20
40
60
80
-40
100
Junction Temperature (°C)
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
-20
0
20
40
60
80
100
Junction Temperature (°C)
6
www.anpec.com.tw
APL1431L
Packaging Information
SOT-23-5
e1
5
4
E1
1
E
3
2
e
b
D
A2
A
a
A1
Dim
A
A1
A2
b
D
E
E1
e
e1
L
L1
L2
N
α
L 2
L
M illimet ers
M in.
0.95
0.05
0.90
0.30
2.8
2.6
1.5
Inches
M ax.
1.45
0.15
1.30
0.50
3.00
3.00
1.70
M in.
0.037
0.002
0.035
0.011
0.110
0.102
0.059
0.55
0.014
0.7
0.020
0.20 BSC
0.5
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
0.022
0.008 BSC
5
0°
M ax.
0.057
0.006
0.051
0.019
0.118
0.118
0.067
0.037BSC
0.074BSC
0.95BSC
1.90BSC
0.35
L 1
0.028
5
10°
7
0°
10°
www.anpec.com.tw
APL1431L
Physical Specifications
Terminal Material
Lead Solderability
Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn
Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reflow Condition
(IR/Convection or VPR Reflow)
tp
TP
C ritical Zone
T L to T P
T e m p e ra tu re
R am p-up
TL
tL
T sm ax
T sm in
R am p-down
ts
Preheat
25
t 25 °C to Peak
T im e
Classificatin Reflow Profiles
Profile Feature
Sn-Pb Eutectic Assembly
Large Body
Small Body
Average ramp-up rate
3°C/second max.
(TL to TP)
Preheat
- Temperature Min (Tsmin)
100°C
- Temperature Mix (Tsmax)
150°C
- Time (min to max)(ts)
60-120 seconds
Tsmax to TL
- Ramp-up Rate
Tsmax to TL
- Temperature(TL)
183°C
- Time (tL)
60-150 seconds
Peak Temperature(Tp)
225 +0/-5°C
240 +0/-5°C
Time within 5°C of actual Peak
10-30 seconds
10-30 seconds
Temperature(tp)
Ramp-down Rate
6°C/second max.
6 minutes max.
Time 25°C to Peak Temperature
Pb-Free Assembly
Large Body
Small Body
3°C/second max.
150°C
200°C
60-180 seconds
3°C/second max
217°C
60-150 seconds
245 +0/-5°C
250 +0/-5°C
10-30 seconds
20-40 seconds
6°C/second max.
8 minutes max.
Note: All temperatures refer to topside of the package. Measured on the body surface.
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
8
www.anpec.com.tw
APL1431L
Reliability Test Program
Test item
SOLDERABILITY
HOLT
PCT
TST
ESD
Latch-Up
Method
MIL-STD-883D-2003
MIL-STD-883D-1005.7
JESD-22-B,A102
MIL-STD-883D-1011.9
MIL-STD-883D-3015.7
JESD 78
Description
245°C, 5 SEC
1000 Hrs Bias @125°C
168 Hrs, 100%RH, 121°C
-65°C~150°C, 200 Cycles
VHBM > 2KV, VMM > 200V
10ms, 1tr > 100mA
Carrier Tape & Reel Dimensions
t
D
P
Po
E
P1
Bo
F
W
Ko
Ao
D1
T2
J
C
A
B
T1
Application
SOT-23-5
A
B
C
J
178 ±1
72 ± 1.0
F
D
D1
Po
3.5 ± 0.05
1.5± 0.1
1.5± 0.1
4.0 ± 0.1
13.0 + 0.2 2.5 ± 0.15
T1
T2
W
P
E
8.4 ± 2
1.5 ± 0.3
8.0 ± 0.3
4 ± 0.1
1.75± 0.1
P1
Ao
Bo
Ko
t
3.2± 0.1
1.4± 0.1
0.2±0.033
2.0 ± 0.1 3.15 ± 0.1
(mm)
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
9
www.anpec.com.tw
APL1431L
Cover Tape Dimensions
Application
SOT- 23-5
Carrier Width
8
Cover Tape Width
5.3
Devices Per Reel
3000
Customer Service
Anpec Electronics Corp.
Head Office :
5F, No. 2 Li-Hsin Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
7F, No. 137, Lane 235, Pac Chiao Rd.,
Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.
Tel : 886-2-89191368
Fax : 886-2-89191369
Copyright  ANPEC Electronics Corp.
Rev. A.4 - May., 2003
10
www.anpec.com.tw