MHP10 SERIES Single and dual output • • • • • • • 2 x 1 x 0.4 inch package 12.5 Watts/in3 power density 32 models including 3.3VDC and 2.1VDC Designed to meet EN60950 Indefinite short circuit protection Optional remote ON/OFF Optional trim output The MHP10 series of DC/DC converters, comprising 32 different models, has been designed for a wide range of applications including communications, industrial systems and mobile battery powered systems. Packing 10 Watts of power into a 2 x 1 x 0.4 inch package, with efficiencies as high as 80% the MHP10 has wide input ranges of 4.5-9VDC, 9-18VDC, 18-36VDC and 3672VDC and is available in both single and dual output versions. Other features include indefinite short circuit protection with automatic recovery and remote on/off, all of which minimize the need for external circuitry and make the MHP10 a recommended component in distributed power systems. [ 2 YEAR WARRANTY ] SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS INPUT SPECIFICATIONS CONTINUED Voltage adjustability See Note 3 ±10% Line regulation LL to HL, all outputs ±0.1% Remote ON/OFF Logic compatibility ON OFF Load regulation ML to FL Single outputs Dual outputs ±0.1% ±1.0% GENERAL SPECIFICATIONS Cross regulation Asymmetrical load 25% / 100% FL Voltage accuracy 5.0% max. ±2.0% Minimum load 2.1V, 3.3V, 5V Single 12V, 15V Duals: each output 50mA max. 80mA max. 10% FL Overshoot At start-up 3.0% max. Ripple and noise 20MHz bandwidth Transient response 25% load step ±10% typ. max. dev., 0.5ms recovery to within ±1.0% Temperature coefficient Short circuit protection 1.5% pk-pk, max. 20mV rms ±0.02%/°C Hiccup mode See Note 5 Continuous automatic recovery Efficiency 5VDC, nominal, FL 12VDC nominal, FL 24VDC nominal, FL 48VDC nominal, FL Input filter Input/output 500VDC Isolation capacitance Input/output 1nF Switching frequency Fixed Approvals and standards (pending) Safety Input current Input reflected ripple Start-up time PAGE 1 See table Single output Dual outputs 200mA 200mA 500ms 200 to 275kHz VDE0805, EN60950, IEC950 UL1950, CSA C22.2 No. 950 Case material Black coated, metal case Material flammability UL94V-0 Weight MTBF 27g (0.95oz) MIL-HDBK-217F 300,000 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient -25°C to +60°C (See derating curve) Extended temp., -40°C to +60°C option, See Note 1 Non-operating amb. -40°C to +95°C Case +95°C max. Derating See derating curve Cooling Free air convection cooled Relative humidity Non-condensing Altitude Operating Non operating 10,000 feet max. 40,000 feet max. Vibration 5Hz to 500Hz 2.5G rms (approx.) 4.5 to 9VDC 9 to 18VDC 18 to 36VDC 36 to 72VDC Pi filter 78% typ. Isolation voltage INPUT SPECIFICATIONS Input voltage range CMOS/TTL, See Note 4 3.5VDC min. or open 0.8VDC max. 30% to 95% DC/DC CONVERTERS | 10W DC/DC 10 Watt Wide input DC/DC converters INPUT OUTPUT OUTPUT INPUT TYPICAL REGULATION (TYP.) VOLTAGE VOLTAGE CURRENT CURRENT EFFICIENCY LINE LOAD 4.5-9VDC 2.1V 2000mA 1400mA 60% ±0.1% ±0.1% MHP10-05S2V1 (2) 4.5-9VDC 3.3V 2000mA 2095mA 63% ±0.1% ±0.1% MHP10-0533V3 (2) 4.5-9VDC 5.0V 1400mA 2058mA 62% ±0.1% ±0.1% MHP10-05S05 (2) 4.5-9VDC 12V 580mA 1856mA 75% ±0.1% ±0.1% MHP10-05S12 (2) 4.5-9VDC 15V 460mA 1769mA 78% ±0.1% ±0.1% MHP10-05S15 (2) 4.5-9VDC ±5.0V ±600mA 1764mA 68% ±0.1% ±1.0% MHP10-05D05 (2) 4.5-9VDC ±12V ±290mA 1784mA 78% ±0.1% ±1.0% MHP10-05D12 (2) 4.5-9VDC ±15V ±230mA 1769mA 78% ±0.1% ±1.0% MHP10-05D15 (2) 9-18VDC 2.1V 2000mA 583mA 60% ±0.1% ±0.1% MHP10-12S2V1 9-18VDC 3.3V 2000mA 753mA 73% ±0.1% ±0.1% MHP10-12S3V3 9-18VDC 5.0V 2000mA 1068mA 78% ±0.1% ±0.1% MHP10-12S05 9-18VDC 12V 800mA 1025mA 78% ±0.1% ±0.1% MHP10-12S12 9-18VDC 15V 660mA 1068mA 78% ±0.1% ±0.1% MHP10-12S15 9-18VDC ±5.0V ±600mA 704mA 71% ±0.1% ±1.0% MHP10-12D05 9-18VDC ±12V ±400mA 1025mA 78% ±0.1% ±1.0% MHP10-12D12 9-18VDC ±15V ±300mA 1068mA 78% ±0.1% ±1.0% MHP10-12D15 18-36VDC 2.1V 2000mA 291mA 60% ±0.1% ±0.1% MHP10-24S2V1 18-36VDC 3.3V 2000mA 376mA 73% ±0.1% ±0.1% MHP10-24S3V3 18-36VDC 5.0V 2000mA 534mA 78% ±0.1% ±0.1% MHP10-24S05 18-36VDC 12V 800mA 512mA 78% ±0.1% ±0.1% MHP10-24S12 18-36VDC 15V 660mA 528mA 78% ±0.1% ±0.1% MHP10-24S15 18-36VDC ±5.0V ±600mA 347mA 71% ±0.1% ±1.0% MHP10-24D05 18-36VDC ±12V ±400mA 512mA 78% ±0.1% ±1.0% MHP10-24D12 18-36VDC ±15V ±300mA 528mA 78% ±0.1% ±1.0% MHP10-24D15 36-72VDC 2.1V 2000mA 145mA 60% ±0.1% ±0.1% MHP10-48S2V1 36-72VDC 3.3V 2000mA 180mA 73% ±0.1% ±0.1% MHP10-483V3 36-72VDC 5.0V 2000mA 267mA 78% ±0.1% ±0.1% MHP10-48S05 36-72VDC 12V 800mA 256mA 78% ±0.1% ±0.1% MHP10-48S12 36-72VDC 15V 660mA 264mA 78% ±0.1% ±0.1% MHP10-48S15 36-72VDC ±5.0V ±600mA 176mA 77% ±0.1% ±1.0% MHP10-48D05 36-72VDC ±12V ±400mA 256mA 78% ±0.1% ±1.0% MHP10-48D12 36-72VDC ±15V ±300mA 264mA 78% ±0.1% ±1.0% MHP10-48D15 MODEL NUMBER DERATING CURVE Notes 2 3 4 5 Extended operating temperature range is available as an option. To specify a MHP10 that operates down to -40°C, add the suffix ‘-4’ to the model number, e.g. MHP10-24S05-4. 5VDC input, max. 7 Watt output power. External trimming of the output voltage is optional on the single output units, add the suffix ‘-T’ to the end of the model number, e.g. MHP10-05S05-T. Remote on/off is available as an option, add the suffix ‘-S’ to the end of the model number, e.g. MHP10-24D15-S. 5VDC in max. for 1 minute. Output Power (Watts) 60°C 100% Output Power (%) 1 90°C 0% -25°C 0°C 20°C 40°C 60°C 80°C 100°C 120°C Ambient Temperature (°C) http://www.artesyn.com PAGE 2 10W DC/DC | DC/DC CONVERTERS DC/DC CONVERTERS | 10W DC 10 Watt Wide input DC/DC converters PIN CONNECTIONS EXTERNAL OUTPUT TRIMMING PIN NUMBER SINGLE OUTPUTS DUAL OUTPUT 1 + Input + Input 2 - Input - Input 3 + Output + Output Single output models can be externally trimmed by ±10% using either method shown below. 5 5 4 N.C./Trim (Option) TRIM UP Common 10KΩ TRIMPOT TRIM DOWN 5 - Output - Output 6 Control (Option) Control (Option) 3 3 0.40 (10.20) 0.40 (10.20) 0.24 (6.10) 4 4 0.40 (10.16) 0.30 (7.60) 0.20 (5.10) 0.60 (15.20) Ø 0.04 Dia. (1.02) 6 2 1 0.80 (20.30) BOTTOM VIEW 2.00 (50.80) 5 4 3 0.60 (15.20) 0.10 (2.50) 0.40 (10.20) 0.40 (10.20) 0.10 (2.50) 1.00 (25.40) ALL DIMENSIONS IN INCHES (mm) Tolerance : ±0.008 (0.2) max. on pin placement ±0.02 (0.5) max. on outer dimensions DS_MHP10_19980401.PDF PAGE 3