SY3418-E / SY3418-E(B) Semiconductor High Brightness LED Lamp Features • • • • Yellow colored transparency lens type φ3mm(T-1) all plastic mold type Wide viewing angle Low power consumption Outline Dimensions unit : mm STRAIGHT TYPE STOPPER Ø2.74~3.14 TYPE : (B) Ø2.74~3.14 3.90~4.30 2.70~3.10 3.90~4.30 2.70~3.10 1.20 Min. 0.70 Max. 23.00 Min. 1.27 Typ. 5.00~6.00 23.00 Min. 0.70 Max. 1.00 Min. 1.00 Min. 1 2 3.60~4.00 2.54 Typ. 3.50~3.90 0.45 Max. 0.45 Max. 2.54 Typ. KSD-O2C013-000 1 2 3.60~4.00 3.50~3.90 PIN Connections 1. Anode 2. Cathode 1 SY3418-E / SY3418-E(B) Absolute Maximum Ratings (Ta=25oC) Characteristic Symbol Rating Unit Power dissipation PD 75 mW Forward current IF 30 mA IFP 50 mA Reverse voltage VR 4 V Operating temperature range Topr -25∼85 ℃ Storage temperature range Tstg -30∼100 ℃ 1 * Peak forward current 2 260℃ for 10 seconds * Soldering temperature Tsol *1.Duty ratio = 1/16, Pulse width = 0.1ms *2.Keep the distance more than 2.0mm from PCB to the bottom of LED package Electrical / Optical Characteristics Characteristic (Ta=25oC) Symbol Test Condition Min. Typ. Max. Unit VF IF= 20mA - 2.1 2.5 V * Luminous intensity IV IF= 20mA 155 - 520 mcd *4LDomonant wavelength λD ∆λ IF= 20mA 587 593 600 nm IF= 20mA - 30 - nm IR VR=4V - - 10 uA θ1/2 IF= 20mA - ±45 - deg Forward voltage 3 Spectrum bandwidth Reverse current 5 * Half angle *3. Luminous intensity maximum tolerance for each grade classification limit is ±18% *4. Dominant wavelength maximum tolerance for each grade classification limit is ±2nm *5. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity *4. Luminous Intensity Classification M N O 155 ~ 230 230 ~ 350 350 ~ 520 KSD-O2C013-000 2 SY3418-E / SY3418-E(B) Characteristic Diagrams Fig. 2 IV - IF Forward Current IF [mA] Luminous Intensity Iv [mcd] Fig. 1 IF - VF Forward Voltage VF [V] Forward Fig. 3 IF – Ta Current IF [mA] Forward Relative Intensity [%] Current IF [mA] Fig.4 Spectrum Distribution Ambient Temperature Ta [℃] Wavelength λ [nm] Fig. 5 Radiation Diagram Relative Luminous Intensity Iv [%] KSD-O2C013-000 3 SY3418-E / SY3418-E(B) The AUK Corp. products are intended for the use as components in general electronic equipment (Office and communication equipment, measuring equipment, home appliance, etc.). Please make sure that you consult with us before you use these AUK Corp. products in equipments which require high quality and / or reliability, and in equipments which could have major impact to the welfare of human life(atomic energy control, airplane, spaceship, transportation, combustion control, all types of safety device, etc.). AUK Corp. cannot accept liability to any damage which may occur in case these AUK Corp. products were used in the mentioned equipments without prior consultation with AUK Corp.. Specifications mentioned in this publication are subject to change without notice. KSD-O2C013-000 4