ARIZONA MICROTEK, INC. AZ10EL31 AZ100EL31 ECL/PECL D Flip-Flop with Set and Reset FEATURES • • • • PACKAGE AVAILABILITY 475ps Propagation Delay 2.8GHz Toggle Frequency 75kΩ Internal Input Pulldown Resistors Direct Replacement for ON Semiconductor MC10EL31 & MC100EL31 PACKAGE SOIC 8 SOIC 8 TSSOP 8 TSSOP 8 1 2 PART NUMBER AZ10EL31D AZ100EL31D AZ10EL31T AZ100EL31T MARKING AZM10EL31 AZM100EL31 AZTEL31 AZHEL31 NOTES 1,2 1,2 1,2 1,2 Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date Code “YWW” on underside of part. DESCRIPTION The AZ10/100EL31 is a master-slave D flip-flop with set and reset. The device is functionally equivalent to the E131 device with higher performance capabilities. With propagation delays and output transition times significantly faster than the E131, the EL31 is ideally suited for those applications that require the ultimate in AC performance. Both set and reset inputs are asynchronous, level triggered signals. Data enters the master section of the flipflop when the clock is LOW. When the clock transitions from LOW to HIGH, the data in the master section transfers into the slave section and through to the outputs. NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established. TRUTH TABLE LOGIC DIAGRAM AND PINOUT ASSIGNMENT D S* R* CLK Q Q ¯ L H X X X L L H L H L L L H H Z Z X X X L H H L Undef H L L H Undef S 1 D 2 PIN S D R CLK Q, Q ¯ VCC VEE FUNCTION Set Input Data Input Reset Input Clock Input Data Outputs Positive Supply Negative Supply VCC 7 Q 6 Q 5 VEE S Z = LOW to HIGH Transition * Pins will default low when left open PIN DESCRIPTION 8 D Flip Flop CLK 3 R R 4 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com AZ10EL31 AZ100EL31 Absolute Maximum Ratings are those values beyond which device life may be impaired. Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA °C °C 10K ECL DC Characteristics (VEE = -4.75 to -5.5V, VCC = GND) Symbol VOH VOL VIH VIL IIH IIL IEE 1. Characteristic 1 Min -1080 -1950 -1230 -1950 -40°C Typ Max -890 -1650 -890 -1500 Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current D, CLK 150 S, R 300 Input LOW Current 0.5 Power Supply Current 27 32 Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1020 -1950 -1170 -1950 0°C Typ Max -840 -1630 -840 -1480 Min -980 -1950 -1130 -1950 25°C Typ 150 300 0.5 Max -810 -1630 -810 -1480 85°C Typ 150 300 0.5 27 Min -910 -1950 -1060 -1950 32 Max -720 -1595 -720 -1445 150 300 0.5 27 32 27 32 Unit mV mV mV mV μA μA mA 10K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. 2. Characteristic 1,2 Min 3920 3050 3770 3050 -40°C Typ Max 4110 3350 4110 3500 Min 3980 3050 3830 3050 0°C Typ Max 4160 3370 4160 3520 Min 4020 3050 3870 3050 Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current D, CLK 150 150 S, R 300 300 Input HIGH Current 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 27 32 27 32 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ Max 4190 3370 4190 3520 Min 4090 3050 3940 3050 85°C Typ 150 300 150 Max 4280 3405 4280 3555 150 300 150 0.5 27 32 27 32 Unit mV mV mV mV μA μA μA mA 100K ECL DC Characteristics (VEE = -4.2V to -5.5V, VCC = GND) Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. Characteristic 1 Min -1085 -1830 -1165 -1810 -40°C Typ -1005 -1695 Max -880 -1555 -880 -1475 Output HIGH Voltage Output LOW Voltage1 Input HIGH Voltage Input LOW Voltage Input HIGH Current D, CLK 150 S, R 300 Input HIGH Current 150 Input LOW Current 0.5 Power Supply Current 27 32 Each output is terminated through a 50Ω resistor to VCC – 2V. November 2006 * REV - 3 Min -1025 -1810 -1165 -1810 0°C Typ -955 -1705 Max -880 -1620 -880 -1475 Min -1025 -1810 -1165 -1810 25°C Typ -955 -1705 150 300 150 0.5 Max -880 -1620 -880 -1475 www.azmicrotek.com 2 32 85°C Typ -955 -1705 150 300 150 0.5 27 Min -1025 -1810 -1165 -1810 Max -880 -1620 -880 -1475 150 300 150 0.5 27 32 31 37 Unit mV mV mV mV μA μA μA mA AZ10EL31 AZ100EL31 100K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol VOH VOL VIH VIL IIH IIH IIL IEE 1. 2. Characteristic 1,2 Min 3915 3170 3835 3190 -40°C Typ 3995 3305 Max 4120 3445 4120 3525 Min 3975 3190 3835 3190 0°C Typ 4045 3295 Max 4120 3380 4120 3525 Min 3975 3190 3835 3190 Output HIGH Voltage Output LOW Voltage1,2 Input HIGH Voltage1 Input LOW Voltage1 Input HIGH Current D, CLK 150 150 S, R 300 300 Input HIGH Current 150 150 Input LOW Current 0.5 0.5 0.5 Power Supply Current 27 32 27 32 For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ 4045 3295 Max 4120 3380 4120 3525 Min 3975 3190 3835 3190 85°C Typ 4045 3295 150 300 150 Max 4120 3380 4120 3525 150 300 150 0.5 27 32 31 37 Unit mV mV mV mV μA μA μA mA AC Characteristics (VEE =10E(-4.75V to -5.5V), 100E(-4.2V to -5.5V); VCC =GND or VEE =GND; VCC =10E(+4.75V to +5.5V), 100E(+4.2V to +5.5V)) Symbol fMAX tPLH / tPHL tS tH tRR tPW tr / t f Characteristic Maximum Toggle Frequency Propagation Delay to Output CLK S,R Setup Time Hold Time Set/Reset Recovery Minimum Pulse Width CLK, Set, Reset Output Rise/Fall Times Q (20% - 80%) November 2006 * REV - 3 Min -40°C Typ 2.0 2.5 315 295 150 250 400 465 455 0 100 200 Max 630 630 400 100 Min 0°C Typ 2.2 2.8 365 345 150 250 400 465 455 0 100 200 Max 580 580 400 350 100 www.azmicrotek.com 3 Min 25°C Typ 2.2 2.8 375 355 150 250 400 475 465 0 100 200 Max 590 590 400 350 100 Min 85°C Typ 2.2 2.8 430 400 150 250 400 530 510 0 100 200 Max GHz 645 645 100 ps ps ps 400 350 Unit ps 350 ps AZ10EL31 AZ100EL31 PACKAGE DIAGRAM SOIC 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. November 2006 * REV - 3 DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z θ www.azmicrotek.com 4 MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O AZ10EL31 AZ100EL31 PACKAGE DIAGRAM TSSOP 8 DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. November 2006 * REV - 3 www.azmicrotek.com 5 MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O AZ10EL31 AZ100EL31 Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. November 2006 * REV - 3 www.azmicrotek.com 6