AZ10LVEL16 AZ100LVEL16 ARIZONA MICROTEK, INC. ECL/PECL Differential Receiver FEATURES • • • • • • • PACKAGE AVAILABILITY Green and RoHS Compliant / Lead (Pb) Free Packages available 250ps Propagation Delay High Bandwidth Output Transitions Operating Range of 3.0V to 5.5V Internal Input Pulldown Resistors Direct Replacement For ON Semiconductor MC10EL16, MC100EL16, & MC100LVEL16 IBIS Model Files Available on Arizona Microtek Website DESCRIPTION PACKAGE PART NUMBER MARKING AZM10 LVEL16 AZM100 LVEL16 NOTES SOIC 8 AZ10LVEL16D SOIC 8 AZ100LVEL16D SOIC 8 RoHS Compliant / Lead (Pb) Free AZ100LVEL16D+ AZM100+ LVEL16 1,2 TSSOP 8 AZ10LVEL16T AZT LV16 1,2 TSSOP 8 RoHS Compliant / Lead (Pb) Free AZ10LVEL16T+ AZT+ LV16 1,2 TSSOP 8 AZ100LVEL16T AZH LV16 1,2 AZ100LVEL16T+ AZH+ LV16 1,2 TSSOP 8 RoHS Compliant / Lead (Pb) Free MLP 8 (2x2) Green / RoHS Compliant / Lead (Pb) Free 1,2 1,2 The AZ10/100LVEL16 is a differential Q6G AZ100LVEL16NG 1,3 receiver. The device is functionally equivalent <Date Code> to the E116 device with higher performance capabilities. With output transition times 1 Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. significantly faster than the E116, the LVEL16 2 Date code format: “Y” or “YY” for year followed by “WW” for week on is ideally suited for interfacing with high underside of part. frequency sources. 3 Date code format: “Y” for year followed by “WW” for week. The LVEL16 provides a VBB output for single-ended use or a DC bias reference for AC coupling to the device. For single-ended input applications, the VBB reference should be connected to one side of the D/D ¯ differential input pair. The input signal is then fed to the other D/D ¯ input. The VBB pin can support 1.5 mA sink/source current. When used, the VBB pin should be bypassed to ground via a 0.01 μF capacitor. Under open input conditions internal input clamps will force the Q output LOW. NOTE: Specifications in the ECL/PECL tables are valid when thermal equilibrium is established. PINOUT ASSIGNMENT PIN DESCRIPTION PIN D, D ¯ Q, Q ¯ VBB VCC VEE NC FUNCTION Data Inputs Data Outputs Reference Voltage Output Positive Supply Negative Supply No Connect NC 1 8 VCC D 2 7 Q D 3 6 Q VBB 4 5 VEE 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com AZ10LVEL16 AZ100LVEL16 Absolute Maximum Ratings are those values beyond which device life may be impaired. Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA °C °C 10K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND) Symbol Characteristic 1 Min -1080 -1950 -1230 -1950 -1430 -150 -40°C Typ Max -890 -1650 -890 -1500 -1300 VOH Output HIGH Voltage VOL Output LOW Voltage1 VIH Input HIGH Voltage VIL Input LOW Voltage VBB Reference Voltage Input LOW Current IIL Input HIGH Current 150 IIH IEE Power Supply Current 18 22 1. Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1020 -1950 -1170 -1950 -1380 -150 0°C Typ 18 Max -840 -1630 -840 -1480 -1270 Min -980 -1950 -1130 -1950 -1350 -150 150 22 25°C Typ 18 Max -810 -1630 -810 -1480 -1250 Min -910 -1950 -1060 -1950 -1310 -150 150 22 85°C Typ 18 Max -720 -1595 -720 -1445 -1190 150 22 Unit mV mV mV mV mV μA μA mA 10K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V) Symbol Characteristic 1,2 Min 2220 1350 2070 1350 1870 -150 -40°C Typ Max 2410 1650 2410 1800 2000 Min 2280 1350 2130 1350 1920 -150 0°C Typ Max 2460 1670 2460 1820 2030 Min 2320 1350 2170 1350 1950 -150 VOH Output HIGH Voltage VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 VBB Reference Voltage1 Input LOW Current IIL IIH Input HIGH Current 150 150 IEE Power Supply Current 18 22 18 22 1. For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ 18 Max 2490 1670 2490 1820 3050 Min 2390 1350 2240 1350 1990 -150 150 22 85°C Typ 18 Max 2580 1705 2580 1855 1390 150 22 Unit mV mV mV mV mV μA μA mA 10K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol Characteristic Min 3920 3050 3770 3050 3570 -150 -40°C Typ Max 4110 3350 4110 3500 3700 Min 3980 3050 3830 3050 3620 -150 0°C Typ Max 4160 3370 4160 3520 3730 Min 4020 3050 3870 3050 3650 -150 VOH Output HIGH Voltage1,2 VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 VBB Reference Voltage1 Input LOW Current IIL IIH Input HIGH Current 150 150 IEE Power Supply Current 18 22 18 22 1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. April 2007 * REV - 8 www.azmicrotek.com 2 25°C Typ 18 Max 4190 3370 4190 3520 3750 150 22 Min 4090 3050 3940 3050 3690 -150 85°C Typ 18 Max 4280 3405 4280 3555 3810 150 22 Unit mV mV mV mV mV μA μA mA AZ10LVEL16 AZ100LVEL16 100K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND) Symbol Characteristic 1 Min -1085 -1830 -1165 -1810 -1380 -150 -40°C Typ -1005 -1695 Max -880 -1555 -880 -1475 -1260 VOH Output HIGH Voltage VOL Output LOW Voltage1 VIH Input HIGH Voltage VIL Input LOW Voltage VBB Reference Voltage Input LOW Current IIL Input HIGH Current 150 IIH IEE Power Supply Current 18 22 1. Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1025 -1810 -1165 -1810 -1380 -150 0°C Typ -955 -1705 18 Max -880 -1620 -880 -1475 -1260 Min -1025 -1810 -1165 -1810 -1380 -150 150 22 25°C Typ -955 -1705 18 Max -880 -1620 -880 -1475 -1260 Min -1025 -1810 -1165 -1810 -1380 -150 150 22 85°C Typ -955 -1705 18 Max -880 -1620 -880 -1475 -1260 150 24 Unit mV mV mV mV mV μA μA mA 100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V) Symbol Characteristic Min 2215 1470 2135 1490 1920 -150 -40°C Typ 2295 1605 Max 2420 1745 2420 1825 2040 Min 2275 1490 2135 1490 1920 -150 0°C Typ 2345 1595 Max 2420 1680 2420 1825 2040 Min 2275 1490 2135 1490 1920 -150 VOH Output HIGH Voltage1,2 VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 VBB Reference Voltage1 Input LOW Current IIL IIH Input HIGH Current 150 150 IEE Power Supply Current 18 22 18 22 1. For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ 2345 1595 18 Max 2420 1680 2420 1825 2040 Min 2275 1490 2135 1490 1920 -150 150 22 85°C Typ 2345 1595 18 Max 2420 1680 2420 1825 2040 150 24 Unit mV mV mV mV mV μA μA mA 100K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol Characteristic 1,2 Min 3915 3170 3835 3190 3620 -150 -40°C Typ 3995 3305 Max 4120 3445 4120 3525 3740 Min 3975 3190 3835 3190 3620 -150 0°C Typ 4045 3295 Max 4120 3380 4120 3525 3740 Min 3975 3190 3835 3190 3620 -150 VOH Output HIGH Voltage VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 VBB Reference Voltage1 Input LOW Current IIL IIH Input HIGH Current 150 150 IEE Power Supply Current 18 22 18 22 1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ 4045 3295 18 Max 4120 3380 4120 3525 3740 Min 3975 3190 3835 3190 3620 -150 150 22 85°C Typ 4045 3295 Max 4120 3380 4120 3525 3740 18 150 24 85°C Typ Max Unit mV mV mV mV mV μA μA mA AC Characteristics (VEE = -3.0V to -5.5V; VCC = GND or VEE = GND; VCC = +3.0V to +5.5V) Symbol Characteristic Min -40°C Typ Max Min 0°C Typ Max Min 25°C Typ Max Min Propagation Delay to Output (Diff) 125 250 375 175 250 325 175 250 325 205 280 355 (SE) 75 250 425 125 250 375 125 250 375 155 280 405 tSKEW Duty Cycle Skew 1(Diff) 5 5 20 5 20 5 20 VPP (AC) Minimum Input Swing2 150 150 150 150 Common Mode Range3 VEE + VCC - VEE + VCC - VEE + VCC - VEE + VCC VPP < 500mV 1.2 0.4 1.1 0.4 1.1 0.4 1.1 0.4 VCMR 1.5 0.4 1.4 0.4 1.4 0.4 1.4 0.4 VPP ≥ 500mV Output Rise/Fall Times Q tr / t f 100 260 100 260 100 260 100 260 (20% - 80%) 1. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. 2. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. The device has a DC gain of ≈ 40. 3. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min) and 1V. tPLH / tPHL April 2007 * REV - 8 www.azmicrotek.com 3 Unit ps ps mV V ps AZ10LVEL16 AZ100LVEL16 PACKAGE DIAGRAM SOIC 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. April 2007 * REV - 8 DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z θ www.azmicrotek.com 4 MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O AZ10LVEL16 AZ100LVEL16 PACKAGE DIAGRAM TSSOP 8 DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. April 2007 * REV - 8 www.azmicrotek.com 5 MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O AZ10LVEL16 AZ100LVEL16 PACKAGE DIAGRAM MLP 8 2x2mm Pin 1 Dot By Marking 2.000±0.050 MLP 8 (2x2mm) 2.000±0.050 TOP VIEW Pin 1 Identification R0.100 TYP 0.350±0.050 0.250±0.050 0.500 bsc 8 1 7 6 2 1.200±0.050 exp. pad 3 5 4 0.600±0.050 exp. pad BOTTOM VIEW 0.750±0.050 0.000-0.050 1 2 SIDE VIEW Note: All dimensions are in mm April 2007 * REV - 8 www.azmicrotek.com 6 3 4 0.203±0.025 1.750 Ref. AZ10LVEL16 AZ100LVEL16 Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. April 2007 * REV - 8 www.azmicrotek.com 7