AZM AZ100LVEL16VRL

ARIZONA MICROTEK, INC.
AZ100LVEL16VR
ECL/PECL Oscillator Gain Stage & Buffer with Selectable Enable
FEATURES
•
•
•
•
•
•
•
•
Green and RoHS Compliant /
Lead (Pb) Free Packages Available
Enhanced Enable Operation
High Bandwidth for ≥1GHz
Similar Operation as AZ100EL16VO
Minimizes External Components
Selectable Enable Polarity and
Threshold (CMOS/TTL or PECL)
Available in a MLP 16 or MLP 8
Package
S–Parameter (.s2p) and IBIS Model
Files Available on Arizona Microtek
Website
PACKAGE AVAILABILITY
PACKAGE
MLP 16 (3x3)
MLP 16 (3x3) RoHS
Compliant / Lead
(Pb) Free
MLP 8 (2x2) Green /
RoHS Compliant /
Lead (Pb) Free
DIE
1
2
3
PART NO.
AZ100LVEL16VRL
AZ100LVEL16VRL+
MARKING
AZM
16R
<Date Code>
AZM+
16R
<Date Code>
NOTES
1,2
1,2
AZ100LVEL16VRNEG
R5G
<Date Code>
1,2
AZ100LVEL16VRX
N/A
3
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts)
Tape & Reel.
Date code format: “Y” for year followed by “WW” for week.
Waffle Pack
DESCRIPTION
The AZ100LVEL16VR is a specialized oscillator gain stage with high gain output buffer including an enable
function. The QHG/Q
¯ HG outputs have voltage gain several times greater than the Q/Q
¯ outputs.
MLP 16, 3x3 mm Package (VRL) or DIE (VRX)
The AZ100LVEL16VR provides a selectable QHG/Q
¯ HG enable that allows continuous oscillator operation via
the Q/Q
¯ outputs. The enable truth table on the next page shows the operating modes. Leaving EN-SEL open (NC)
selects PECL/ECL operation for the EN pad/pin. In this mode the QHG/Q
¯ HG outputs are enabled when EN is left
open (NC) or set to a PECL/ECL low.
Connecting EN-SEL to VCC, VEE or VBB selects CMOS operation for the EN pad/pin. When EN-SEL is tied to
VEE, the QHG/Q
¯ HG outputs are disabled when EN is left open (NC). When EN-SEL is tied to VCC or VBB, the QHG/Q
¯
1
HG outputs are enabled when EN is left open. This default logic condition can be overridden by a ≤20kΩ resistor
connected to the opposite supply.
The AZ100LVEL16VR also provides a VBB and 470Ω internal bias resistors from D to VBB and D
¯ to VBB. The
VBB pin supports 1.5mA sink/source current. VBB should be bypassed to ground or VCC with a 0.01 μF capacitor.
Outputs Q/Q
¯ each have a selectable on-chip pull-down current source. See the current source truth table on the
next page for the supported values. External resistors may also be used to increase pull-down current to a maximum
total of 25mA for the Q/Q
¯ outputs.
Each of the QHG/Q
¯ HG outputs has an optional on-chip pull-down current source of 10 mA. When pad/pin VEEP is
left open (NC), the output current sources are disabled and the QHG /Q
¯ HG operate as standard PECL/ECL. When VEEP
is connected to VEE, the current sources are activated. The QHG /Q
¯ HG pull-down current can be decreased by using a
resistor between VEEP and VEE.
1
This operational mode (EN-SEL to VCC or VBB) is not supported for date codes prior to 0428 (July 2004). EN-SEL to VEE is supported for all
date codes.
1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541
www.azmicrotek.com
AZ100LVEL16VR
MLP 16 (VRL) AND DIE (VRX)
AZ100LVEL16VRL
MLP 16
4mA EA.
Q
Q
CS-SEL
D
QHG
D
QHG
470
VBB
NC
1
D
2
D
3
VBB
4
Q
Q
NC
VCC
16
15
14
13
12 CS-SEL
Leave Pad
Open or
Connect to
VEE
10mA EA.
EN
VEEP
VEE
CMOS / TTL
THRESHOLD
EN-SEL
5
6
7
8
EN
NC
VEE
VEEP
AZ100LVEL16VRL, VRX
11
QHG
10
QHG
9
EN-SEL
TOP VIEW
ENABLE TRUTH TABLE
EN-SEL
EN
Q/Q
¯ QHG Q
¯ HG
NC
PECL Low, VEE or NC
Data Data Data
NC
PECL High or VCC
Data Low High
VEE1
Data Low High
CMOS Low, VEE or NC
VEE1
CMOS High or VCC
Data Data Data
VCC or VBB1,2 CMOS Low or VEE
Data Low High
VCC or VBB 1,2 CMOS High, VCC or NC Data Data Data
1
EN-SEL connections must be ≤1Ω.
2
Date codes prior to 0428 do not support this operating mode.
PIN DESCRIPTION
PIN
CURRENT SOURCE TRUTH TABLE
CS-SEL
Q
Q
¯
NC
4mA typ.
4mA typ.
VEE1
8mA typ.
8mA typ.
VCC1
0
4mA typ.
1
Connections to VCC or VEE must be ≤1Ω.
D/D
¯
Q/Q
¯
QHG/Q
¯ HG
VBB
EN-SEL
EN
CS-SEL
VEEP
VEE
VCC
April 2007 * REV - 15
www.azmicrotek.com
2
FUNCTION
Data Inputs
Data Outputs
Data Outputs w/High Gain
Reference Voltage Output
Enable Logic Select
Enable Input
Selects Q and Q
¯ Current Source
Magnitude
Optional QHG and Q
¯ HG Current
Sources
Negative Supply
Positive Supply
AZ100LVEL16VR
MLP 16 (VRL) AND DIE (VRX)
D
EN (EN-SEL NC)
(PECL)
EN (EN-SEL CONNECTED TO VEE
(CMOS)
or V CC)
Q
Q
QHG
QHG
TIMING DIAGRAM
DIE PAD COORDINATES
EL16VR
A
B
L
M
A
B
C
D
E
F
G
H
I
J
K
L
M
D
D
¯
VBB
EN
VEE
VEEP
EN-SEL
Q
¯ HG
QHG
CS-SEL
VCC
Q
Q
¯
J
BOND PAD: 85u X 85u
D
Notes:
SIGNAL
DIE SIZE: 950u X 940u
DIE THICKNESS: 14 MILS
C
K
NAME
E
F
I
H
G
1. Other die thicknesses available. Contact
factory for further information.
2. The die backside may be left open or
connected to VEE.
April 2007 * REV - 15
www.azmicrotek.com
3
X
(Microns)
-342.5
-342.5
-342.5
-342.5
-33.5
126.5
312.5
312.5
312.5
312.5
302.5
142.5
-140.5
Y
(Microns)
312.5
144.5
-87.0
-255.0
-312.5
-312.5
-248.5
-98.5
51.5
201.5
342.5
342.5
342.5
AZ100LVEL16VR
MLP 8, 2x2 mm Package (VRNE)
A CMOS enable input (EN) allows continuous oscillator operation. When the EN input is HIGH or left open
(NC), the Q
¯ and QHG/Q
¯ HG outputs follow the data input. When EN is LOW, the QHG output is forced high and the Q
¯
¯ continues to follow the data input. The Q
¯ output has an internal 4 mA current source
HG output is forced low while Q
to VEE, in most cases eliminating the need for an external pull-down resistor.
¯ is
The data input D is tied to the VBB pin through a 470 Ω internal bias resistor while the inverting input D
connected directly to VBB. Bypassing VBB to ground with a 0.01 μF capacitor is recommended.
NOTE: The specifications in the ECL/PECL tables are valid when thermal equilibrium has been established.
PIN DESCRIPTION
4mA
Q
D
QHG
QHG
470
VEE
VBB
EN
PIN
D
Q
¯
QHG/Q
¯ HG
VBB
EN
VEE
VCC
FUNCTION
Data Input
Data Output
Data Outputs w/High Gain
Reference Voltage Output
Enable Input
Negative Supply
Positive Supply
AZ100LVEL16VRNE
D
EN
AZ100LVEL16VRNE
MLP 8, 2x2 mm
(CMOS Input
Levels)
Q
QHG
QHG
D
1
VBB
2
EN
3
VEE
4
Leave Pad
open or
connect to
VEE
TIMING DIAGRAM
TOP VIEW
April 2007 * REV - 15
www.azmicrotek.com
4
8
Q
7
VCC
6
QHG
5
QHG
AZ100LVEL16VR
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol
VCC
VD/D¯
VEN
VEE
VD/D¯
VEN
IOUT
IHGOUT
TA
TSTG
Characteristic
PECL Power Supply
(VEE = 0V)
PECL D/D
¯ Input Voltage
(VEE = 0V)
PECL EN Input Voltage
(VEE = 0V)
ECL Power Supply
(VCC = 0V)
ECL D/D
¯ Input Voltage
(VCC = 0V)
ECL EN Input Voltage
(VCC = 0V)
Output Current, Q/Q
¯
— Continuous
— Surge
¯ HG — Continuous
Output Current, QHG/Q
— Surge
Operating Temperature Range
Storage Temperature Range
Rating
0 to +6.0
±0.75 with respect to VBB
0 to +6.0
-6.0 to 0
±0.75 with respect to VBB
-6.0 to 0
25
50
50
100
-40 to +85
-65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
mA
mA
°C
°C
100K ECL DC Characteristics (VEE = -3.0V to -5.5V, VCC = GND)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
-40°C
Characteristic
1
Min
-1045
-1925
0°C
Max
-835
-1555
Min
-1025
-1900
25°C
Max
-835
-1620
Min
-1025
-1900
Output HIGH Voltage
Output LOW Voltage1
Input HIGH Voltage
-1165
-740
-740
-1165
D/D
¯ , EN (ECL)2
-1165
VCC
VCC
VEE+2000
EN (CMOS)3 VEE+2000
VEE+2000
Input LOW Voltage
-1900
-1475
-1900
-1475
-1900
D/D
¯ , EN (ECL)2
VEE
VEE + 800
VEE
VEE + 800
VEE
EN (CMOS)3
Reference Voltage
-1390
-1250
-1390
-1250
-1390
Input HIGH Current EN
150
150
Input LOW Current
0.5
0.5
0.5
EN (ECL)2
-150
-150
-150
EN (CMOS)3
Power Supply Current1
48
48
Specified with VEEP and CS-SEL NC, QHG/Q
¯ HG terminated through 50Ω resistors to VCC - 2V.
EN-SEL = NC.
EN-SEL = VCC or VEE.
85°C
Unit
Max
-835
-1620
Min
-1025
-1900
Max
-835
-1620
-740
VCC
-1165
VEE+2000
-740
VCC
mV
-1475
VEE + 800
-1250
150
-1900
VEE
-1390
-1475
VEE + 800
-1250
150
mV
mV
mV
mV
μA
μA
0.5
-150
48
54
mA
100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
4.
-40°C
Characteristic
1,2
Min
2255
1375
0°C
Max
2465
1745
Min
2275
1400
25°C
Max
2465
1680
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage1
2135
2560
2135
2560
D/D
¯ , EN (PECL)3
EN (CMOS)4
2000
VCC
2000
VCC
Input LOW Voltage1
D/D
¯ , EN (PECL)3
1400
1825
1400
1825
EN (CMOS)4
GND
800
GND
800
Reference Voltage1
1910
2050
1910
2050
Input HIGH Current EN
150
150
Input LOW Current
0.5
0.5
EN (PECL)3
-150
-150
EN (CMOS)4
Power Supply Current2
48
48
For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.
¯ HG terminated through 50Ω resistors to VCC - 2V.
Specified with VEEP and CS-SEL NC, QHG/Q
EN-SEL = NC.
EN-SEL = VCC or VEE.
April 2007 * REV - 15
www.azmicrotek.com
5
85°C
Unit
Min
2275
1400
Max
2465
1680
Min
2275
1400
Max
2465
1680
2135
2000
2560
VCC
2135
2000
2560
VCC
mV
1400
GND
1910
1825
800
2050
150
1400
GND
1910
1825
800
2050
150
mV
0.5
-150
mV
μA
μA
0.5
-150
48
mV
mV
54
mA
AZ100LVEL16VR
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
VOH
VOL
VIH
VIL
VBB
IIH
IIL
IEE
1.
2.
3.
4.
-40°C
Characteristic
0°C
Min
3955
3075
1,2
Max
4165
3445
Min
3975
3100
25°C
Max
4165
3380
Output HIGH Voltage
Output LOW Voltage1,2
Input HIGH Voltage1
3835
4260
3835
4260
D/D
¯ , EN (PECL)3
EN (CMOS)4
2000
VCC
2000
VCC
Input LOW Voltage1
3100
3525
3100
3525
D/D
¯ , EN (PECL)3
EN (CMOS)4
GND
800
GND
800
1
Reference Voltage
3610
3750
3610
3750
Input HIGH Current EN
150
150
Input LOW Current
0.5
0.5
EN (PECL)3
-150
-150
EN (CMOS)4
Power Supply Current2
48
48
For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
¯ HG terminated through 50Ω resistors to VCC - 2V.
Specified with VEEP and CS-SEL NC, QHG/Q
EN-SEL = NC.
EN-SEL = VCC or VEE.
85°C
Unit
Min
3975
3100
Max
4165
3380
Min
3975
3100
Max
4165
3380
3835
2000
4260
VCC
3835
2000
4260
VCC
mV
3100
GND
3610
3525
800
3750
150
3100
GND
3610
3525
800
3750
150
mV
0.5
-150
mV
mV
mV
μA
μA
0.5
-150
48
54
mA
AC Characteristics (VEE = -3.0V to -5.5V; VCC = GND or VEE = GND; VCC = +3.0V to +5.5V)
Symbol
Characteristic
Min
-40°C
Typ
Max
Min
0°C
Typ
Max
Min
25°C
Typ
Max
Min
85°C
Typ
Max
Propagation Delay
400
400
400
400
(SE)
D to Q/Q
¯ Outputs1
¯ HG Outputs2 (SE)
450
450
450
450
D to QHG/Q
tSKEW
Duty Cycle Skew4
(SE)
5
20
5
20
5
20
5
20
VPP (AC) Differential Input Swing5
80
1000
80
1000
80
1000
80
1000
Output Rise/Fall1,2
tr / t f
100
240
100
240
100
240
100
240
(20% - 80%)
1.
Specified with CS-SEL connected to VEE, Q/Q
¯ terminated with an AC coupled 50Ω load.
¯ HG terminated through 50Ω resistors to VCC - 2V.
2.
Specified with VEEP NC, QHG/Q
3.
Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
4.
The peak-to-peak differential input swing is the range for which AC parameters are guaranteed. VD and VD¯ must remain within the range of ± 750
¯ outputs and a voltage gain of ≈ 100 to the QHG/Q
¯ HG outputs.
mV with respect to VBB. The device has a voltage gain of ≈ 20 to the Q/Q
tPLH / tPHL
AC PP INPUT
D
D
V PP (AC)
April 2007 * REV - 15
www.azmicrotek.com
6
Unit
ps
ps
mV
ps
AZ100LVEL16VR
VOUTpp (mV)
Typical Large Signal Outputs, QHG/Q
¯ HG
1000
900
800
700
600
500
400
300
200
100
0
0
500
1000
1500
2000
2500
3000
3500
4000
FREQUENCY (MHz)
Measured with 750mv differential input, VEEP NC, QHG/Q
¯ HG each terminated to VCC2V via 50 Ω resistors.
April 2007 * REV - 15
www.azmicrotek.com
7
AZ100LVEL16VR
0
0.9
-10
0.85
-20
Phase
Magnitude
0.95
0.8
-30
0.75
-40
0.7
S11 MAG 8mA
S11 MAG 4mA
S11 PHASE 8mA
S11 PHASE 4mA
-50
50
150
250
350
450
550
650
750
850
950
1050
1150
1250
1350
Frequency (MHz)
S11, D to Q
¯
0.025
225
0.02
200
0.015
175
Phase
Magnitude
(50 Ω external AC, 4 & 8mA internal DC Load on Q
¯)
0.01
150
0.005
125
0
100
50
150
250
350
450
550
650
750
850
950
1050
1150
1250
1350
Frequency (MHz)
S12, D to Q
¯
(50 Ω external AC, 4 & 8mA internal DC Load on Q
¯)
April 2007 * REV - 15
www.azmicrotek.com
8
S12 MAG 8mA
S12 MAG 4mA
S12 PHASE 8mA
S12 PHASE 4mA
40
200
35
175
30
150
25
125
20
100
15
75
10
50
5
25
0
S21 MAG 8mA
S21 MAG 4mA
S21 PHASE 8mA
S21 PHASE 4mA
Phase
Magnitude
AZ100LVEL16VR
0
50
150
250
350
450
550
650
750
850
950
1050
1150
1250
1350
Frequency (MHz)
S21, D to Q
¯
0.8
200.00
0.75
190.00
0.7
180.00
0.65
170.00
0.6
160.00
0.55
150.00
0.5
140.00
0.45
130.00
0.4
120.00
50
150
250
350
450
550
650
750
850
950
1050 1150 1250 1350
Frequency (MHz)
S22, D to Q
¯
(50 Ω external AC, 4 & 8mA internal DC Load on Q
¯)
April 2007 * REV - 15
www.azmicrotek.com
9
Phase
Magnitude
(50 Ω external AC, 4 & 8mA internal DC Load on Q
¯)
S22 MAG 8mA
S22 MAG 4mA
S22 PHASE 8mA
S22 PHASE 4mA
AZ100LVEL16VR
AC Coupling Capacitor
C2
3.3 or 5 V
CMOS
R1
See table
LVEL16VR
Front End
D
D
VBB
C1
0.01 μF
Application Circuit for CMOS Inputs
R11
Input
Type
AC
Coupled
(C2 in
circuit)
DC
Coupled
(C2
shorted)
3.3 V
1.1 kΩ
2.0 kΩ
CMOS
5 V CMOS
1.6 kΩ
3.3 kΩ
1
R1 should be chosen so that the input swing on the D input
with respect to D
¯ is in the range of ±80 to ±1000 mV, per the
AC Characteristics table and the D input is < ±750 mV with
respect to VBB.
Recommended Component Values for CMOS Single Ended Inputs
April 2007 * REV - 15
www.azmicrotek.com
10
AZ100LVEL16VR
PACKAGE DIAGRAM
MLP 8 2x2mm
Pin 1 Dot
By Marking
2.000±0.050
MLP 8
(2x2mm)
2.000±0.050
TOP VIEW
Pin 1 Identification
R0.100 TYP
0.350±0.050
0.250±0.050
0.500 bsc
8
1
7
6
2 1.200±0.050
exp. pad
3
5
4
0.600±0.050
exp. pad
BOTTOM VIEW
0.750±0.050
0.000-0.050
1
2
SIDE VIEW
Note: All dimensions are in mm
April 2007 * REV - 15
www.azmicrotek.com
11
3 4
0.203±0.025
1.750
Ref.
AZ100LVEL16VR
PACKAGE DIAGRAM
MLP 16
A
D
D
2
2.
INDEX AREA
(D/2 x E/2)
D2
D2/2
B
E2/2
E2
E
2
3x
E
e
2
e
2x
1
aaa C
2x
TOP VIEW
aaa C
bbb M C A B
5.
16 x b
L
3.
3x e
BOTTOM VIEW
ccc C
A3
A
4.
0.08 C
A1
SIDE
VIEW
NOTES:
1. DIMENSIONING AND TOLERANCING
CONFORM TO ASME T14-1994.
2. THE TERMINAL #1 AND PAD
NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012.
3. DIMENSION b APPLIES TO METALLIZED
PAD AND IS MEASURED BETWEEN 0.25
AND 0.30 mm FROM PAD TIP.
4. COPLANARITY APPLIES TO THE
EXPOSED PADS AS WELL AS THE
TERMINALS.
5. INSIDE CORNERS OF METALLIZED PAD
MAY BE SQUARE OR ROUNDED
April 2007 * REV - 15
www.azmicrotek.com
12
C
SEATING
PLANE
MILLIMETERS
DIM
A
A1
A3
b
D
D2
E
E2
e
L
aaa
bbb
ccc
MIN
MAX
0.80
1.00
0.05
0.00
0.25 REF
0.18
0.30
3.10
2.90
1.95
0.25
3.10
2.90
1.95
0.25
0.50 BSC
0.50
0.30
0.25
0.10
0.10
AZ100LVEL16VR
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.
April 2007 * REV - 15
www.azmicrotek.com
13