HIGH FREQUENCY MAGNETICS T1/E1 Miniature Surface Mount Tranformers • • • • Operating temperature range: -40° C to +85° C Meet pulse template and return loss requirements of T1/ • E1 interface circuits • Designed to meet stringent requirements of low-voltage • applications Maximum inductance unbalance of center-tapped windings is 0.2% TM00143 Meets IEC 695, 2-2 flammability requirements PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias Minimum interwinding breakdown voltage of 1500 Vrms ELECTRICAL SPECIFICATIONS at 25° C Part Number Turns Ratio ± 1% Primary Inductance1 mH min Leakage Inductance2 µH max Pri : Sec Surge Voltage Capability3 DCR Ω max Interwinding Capacitance pF typ (4 - 6) (3 - 1) Metallic Longitudinal V peak V peak 2795K 1 : 1.93CT 0.810 0.4 1.2 2.3 35 3000 2500 2795H 1 : 2CT 1.34 0.5 1.8 3.7 45 2500 2500 2795L 1 : 2.1CT 1.1 0.6 1.8 3.8 47 2500 2500 2795J 1 : 2.45CT 0.950 0.4 1.5 3.7 45 2500 2500 1. measured at 10 kHz, 0.5 Vac 2. measured at 100 kHz, 0.1 Vac 3. See Supplementary Information 4. measured at 10 kHz, 0.1 Vac SCHEMATIC Minimum Return Loss for 2795J and 2795K used with Lucent 3.3 volt transceivers 2795H 2795J 2795K 2795L Frequency Interface 4 51 kHz 102 kHz 2 MHz 3 MHz Receive 14 dB 20 dB 20 dB 16 dB Transmit1 9 dB 15 dB 15 dB 11 dB 3 2 CT 6 Primary 1 Secondary 1. For transmit, only, place external capacitor of 470 pF ± 10% across winding (4-6) ©2000 Bel Fuse Inc. Specifications subject to change without notice. 04.00 Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com T1-95 HIGH FREQUENCY MAGNETICS T1/E1 Miniature Surface Mount Tranformers TM00143 MECHANICAL 2795H 2795J 2795K 2795L 0.240 [6.10] max 6 5 4 A 0.186 [4.72] 0.350 [8.90] max 0.265 [6.73] ref 0.073 [1.85] 0.040 [1.02] 0.065 [1.65] 0.057 [1.45] A Terminal 1 ID 1 2 0.020 [0.51] 0.364 0.234 [9.25] [5.95] 3 No metallization or solder mask in cross-hatched designated area 0.073 [1.85] 0.265 [6.73] max 0.055 [1.40] 0˚/8˚ 0.015 [0.40] Supplementary Information Safety Agency Compatibility Surge Voltage Capability Flammability Compliance Simulation Model Surface-Mount Packaging Terminal Lead Coplanarity PWB Process Capability 0.033 [0.84] Suggested PCB Pad Layout Note: Unless otherwise specified, dimensions are nominal and in inches [millimeters]. R 0.023 [0.60] Underwriters Laboratories, Inc. UL 1950 10/700 µs; 10 repetitions of alternating polarity, generator output: peak voltage, 25 Ω source IEC-695, 2-2 (needle flame test), materials are UL 94 VO approved SPICE computer simulation file available on request Tape and Reel; 16 mm wide by 12 mm pitch; 13 inch OD; 4 inch ID 650 transformers per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards—JEDEC SO package 0.004 inch [0.10 mm] Machine placement (recommendation: locate by terminals, not body) ©2000 Bel Fuse Inc. Specifications subject to change without notice. 04.00 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 198 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com T1-96