NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B V7PD-15B Series • Nonisolated • Industry standard pinout • Fixed frequency • High efficiency means less power dissipation • Optimized for cost • Remote on/off • Undervoltage lockout (UVLO) • Over current and short circuit protection • Remote sense • Over temperature shutdown protection Description The Bel V7PD-15B modules are a series of non-isolated, step down DC/DC power converters that operate from a nominal 5V source. These converters are available in a range of output voltages from 1.2V to 3.3V. They are packaged in an industry standard, single-in-line footprint and provide a maximum 15A output. Standard features include remote on/off, over current and short circuit protection, output voltage adjust and remote sense. These products may be used almost anywhere low voltage silicon is employed and a 5V source is available. Typical applications include file servers, routers, line cards and other computing and communications equipment. Applications Options • Distributed power architectures • • Data networking equipment • Telecommunications • Computers and peripherals Reverse remote on/off logic Part Number Selection Output Voltage Input Voltage Max. Output Current Max. Output Power Typical Efficiency Part Number Active High Part Number Active Low 3.3V 5V 15A 49.5W 93% V7PD-15B330 V7PD-15B33L 2.5V 5V 15A 37.5W 91% V7PD-15B250 V7PD-15B25L 1.8V 5V 15A 27.0W 89% V7PD-15B180 V7PD-15B18L 1.5V 5V 15A 22.5W 86% V7PD-15B150 V7PD-15B15L 1.2V 5V 15A 18.0W 83% V7PD-15B120 V7PD-15B12L ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Absolute Maximum Ratings Parameter Max Unit -0.3 6 V Vouten -0.3 6 V Ambient Temperature Tamb 0 70 °C Storage Temperature Tstor -55 105 °C Continuous Input Voltage Output Enable Terminal Voltage Symbol Min Vin Typical Note: Use beyond the maximum ratings may cause a reliability degradation of the DC/DC converter or may permanently damage the device. Input Specifications Parameter Operating Input Voltage Module Symbol Min Typical Max Units All Vin 4.5 5 5.5 V Input Current A Iin 13.5 10.5 7.6 6.5 5.3 3.3V 2.5V 1.8V 1.5V 1.2V No Load Input Current All 70 100 mA Remote Off Input Current Al l 6 10 mA Input Reflected Ripple Current1 All 50 80 mArms Input Reflected Ripple Current (P-P)1 All 135 160 mApk I2t Inrush Current Transient All 0.18 A 2s Turn On Voltage Threshold All 4.25 V Turn Off Voltage Threshold All 3.85 V Note: Input capacitance a 680µF/6.3V and a 270µF/16V Oscon caps 1. With simulated source impedance of 500nH, 5Hz to 20MHz. ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 2 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Output Specifications Parameter Module Output Voltage Set Point Min Typical Max 3.234 2.450 1.764 1.470 1.176 3.3 2.5 1.8 1.5 1.2 3.366 2.550 1.836 1.530 1.224 3.3V 2.5V 1.8V 1.5V 1.2V 8 6 6 5 5 16.5 12.5 11.0 10.5 10.5 3.3V 2.5V 1.8V 1.5V 1.2V 5 3 3 2 2 10 7.5 6.0 4.5 4.5 3.3V 2.5V 1.8V 1.5V 1.2V 15 10 7 5 5 35 25 20 15 15 3.3V 2.5V 1.8V 1.5V 1.2V 28 19 16 12 12 61.5 45 37 30 30 50 50 48 45 38 100 100 90 80 70 25 20 18 15 12 30 25 23 20 17 1 Symbol Vout 3.3V 2.5V 1.8V 1.5V 1.2V Units V Load Regulation mV Line Regulation mV Regulation Over Temperature mV Total Output Voltage Regulation mV Output Ripple and Noise 2 3.3V 2.5V 1.8V 1.5V 1.2V Output Ripple and Noise 2 mVp-p mVrms 3.3V 2.5V 1.8V 1.5V 1.2V Output Current Range All Iout 0 15 A Output DC Current Limit All Ioutlim 19.5 37.5 A Shor t Circuit Surge A2s Ioutsurge 0.041 0.048 0.070 0.081 0.095 3.3V 2.5V 1.8V 1.5V 1.2V Turn on Time All Overshoot at Turn On All Output Capacitance All Ton Cout 0 11 20 ms 0 3 % 6800 µF Note: All specifications are typical at nominal input, full load at 25° C unless otherwise stated. 1. Vin = 5V, Iout = full load, Ta = 25° C. 2. 0 - 20MHz, 0.1µF ceramic cap on output. ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 3 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Output Specifications Parameter Module Transient Response Symbol Min Typical Max Units 88 150 mV 20 50 µs 85 150 mV 20 50 µs 95 150 mV 20 50 µs 95 150 mV 20 50 µs 94 150 mV 20 50 µs 92 150 mV 20 50 µs 95 150 mV 20 50 µs 95 150 mV 20 50 µs 80 150 mV 20 50 µs 75 150 mV 20 50 µs 3 ∆V 50% to 100% of Max Load Settling Time Ts 3.3V ∆V 100% to 50% of Max Load Settling Time Ts Transient Response 3 ∆V 50% to 100% of Max Load Settling Time Ts 2.5V ∆V 100% to 50% of Max Load Settling Time Ts Transient Response 3 ∆V 50% to 100% of Max Load Settling Time Ts 1.8V ∆V 100% to 50% of Max Load Settling Time Ts Transient Response 3 ∆V 50% to 100% of Max Load Settling Time Ts 1.5V ∆V 100% to 50% of Max Load Settling Time Ts Transient Response 3 ∆V 50% to 100% of Max Load Settling Time Ts 1.2V ∆V 100% to 50% of Max Load Settling Time Ts Note: All specifications are typical at nominal input, full load at 25° C unless otherwise stated. 3. di/dt = 0.5A/1µS, Ta = 25° C without external load capacitance. ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 4 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B General Specifications Parameter Module Symbol Min Typical 91 89 87 84 81 93 91 89 86 83 230 300 Max η Efficiency1 3.3V 2.5V 1.8V 1.5V 1.2V Switching Frequency All Fsw Over temperature Shutdown All Tc Output Voltage Trim Range2 All Weight All Units % 340 120 90 kHz °C 110 15 % g 1. Vin=5V, full load and Ta=25° C. 2. See graphs on pages 11-13. Control Specifications Parameter Remote On/Off Module 3 Symbol Min Typical Max Vouten Signal Low (Unit Off) Units V -0.3 0.8 V 2.5 5.5 V -0.3 0.8 V 2.5 5.5 V V7PD-15Bxx0 Signal High (Unit On) Signal Low (Unit On) V7PD-15BxxL Signal High (Unit Off) 3. With remote on/off pin 11 open, the module is on. Note: On/off pin designed to work with an open collector/drain switch. ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 5 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Efficiency Data Module 3.3V Module 2.5V 98% 94% 96% 92% 92% 4.5V 90% 5V 88% 5.5V Efficiency Efficiency 94% 90% 4.5V 88% 5V 5.5V 86% 86% 84% 84% 82% 82% 1 2 3 4 5 6 7 8 9 1 10 11 12 13 14 15 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Output Current Output Current Module 1.8V 94% Efficiency 92% 90% 4.5V 88% 5V 5.5V 86% 84% 82% 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Output Current Module 1.5V Module 1.2V 94% 94% 92% 92% 90% 88% 4.5V 86% 5V 84% 5.5V Efficiency Efficiency 90% 88% 4.5V 86% 5V 84% 5.5V 82% 82% 80% 80% 78% 78% 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Output Current ©2003 Bel Fuse Inc. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Output Current Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 6 NON-ISOLATED DC/DC CONVERTERS 5V Input / 1.2V – 3.3V Output / 15A POWER PRODUCTS BP02V7PD-15B Ripple and Noise 0.1µF ceramic cap added at the output. Ripple and noise at full load and 5Vdc input, 3.3Vdc output and Ta=25° C Ripple and noise at full load and 5Vdc input, 2.5Vdc output and Ta=25° C Ripple and noise at full load and 5Vdc input, 1.8Vdc output and Ta=25° C Ripple and noise at full load and 5Vdc input, 1.5Vdc output and Ta=25° C Ripple and noise at full load and 5Vdc input, 1.2Vdc output and Ta=25° C ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 7 POWER PRODUCTS NON-ISOLATED DC/DC CONVERTERS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Transient Response Transient response: di/dt = 0.5A/µS, no external load capacitance Vout=3.3V 50% to 100% load transients at 5V input and Ta=25° C Vout=3.3V 100% to 50% load transients at 5V input and Ta=25° C Vout=2.5V 50% to 100% load transients at 5V input and Ta=25° C Vout=2.5V 100% to 50% load transients at 5V input and Ta=25° C ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 8 NON-ISOLATED DC/DC CONVERTERS 5V Input / 1.2V – 3.3V Output / 15A POWER PRODUCTS BP02V7PD-15B Transient Response Transient response: di/dt = 0.5A/µS, no external load capacitance Vout=1.8V 50% to 100% load transients at 5V input and Ta=25° C Vout=1.8V 100% to 50% load transients at 5V input and Ta=25° C Vout=1.5V 50% to 100% load transients at 5V input and Ta=25° C Vout=1.5V 100% to 50% load transients at 5V input and Ta=25° C ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 9 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Transient Response Transient response: di/dt = 0.5A/µS, no external load capacitance Vout=1.2V 50% to 100% load transients at 5V input and Ta=25° C Vout=1.2V 100% to 50% load transients at 5V input and Ta=25° C Thermal Considerations V7PD-15B Derating Curve 100LFM 200LFM 300LFM Output Current (A) 15.0 12.0 9.0 6.0 Natural Convection 3.0 0 0 10 20 30 40 50 60 70 85 Ambient Temperature, Ta (˚C) Output Current vs. Local Ambient Temperature and Air Velocity ©2003 Bel Fuse Inc. Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 10 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Output Voltage Set-Point Adjustment Trim Down Test Circuit Trim Up Test Circuit Vo Trim Gnd Vo Trim Gnd Output Voltage Set-Point Adjustment V7PD-15B33x Trim Resistor Calculation Rtrim down = ( Rtrim up = ( ©2003 Bel Fuse Inc. 3.17 Vo adj – 0.767 Vo nom – 3.65) Kohm Vo nom – Vo, adj 0.767 Vo nom Vo, adj – Vo nom – 3.65) Kohm Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 11 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Output Voltage Set-Point Adjustment V7PD-15B25x Trim Resistor Calculation Rtrim down = Rtrim up = ( ( 2.16 Vo adj – 0.689 Vo nom – 2) Kohm Vo nom – Vo, adj 0.689 Vo nom Vo, adj – Vo nom – 2) Kohm V7PD-15B18x Trim Resistor Calculation Rtrim down = ( Rtrim up = ©2003 Bel Fuse Inc. ( 1.51 Vo adj – 0.668 Vo nom – 1.78) Kohm Vo nom – Vo, adj 0.668 Vo nom Vo, adj – Vo nom – 1.78) Kohm Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 12 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Output Voltage Set-Point Adjustment V7PD-15B15x Trim Resistor Calculation Rtrim down = ( Rtrim up = ( 2.06 Vo adj – 1.092 Vo nom – 1.78) Kohm Vo nom – Vo, adj 1.092 Vo nom Vo, adj – Vo nom – 1.78) Kohm V7PD-15B12x Trim Resistor Calculation Rtrim down = ( Rtrim up = ©2003 Bel Fuse Inc. ( 1.22 Vo adj – 0.808 Vo nom – 0.825) Kohm Vo nom – Vo, adj 0.808 Vo nom Vo, adj – Vo nom – 0.825) Kohm Specifications subject to change without notice. 01.03 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 13 NON-ISOLATED DC/DC CONVERTERS POWER PRODUCTS 5V Input / 1.2V – 3.3V Output / 15A BP02V7PD-15B Mechanical V7PD-15B 0.55 [13.97] 0.05 [1.27] 0.39 [9.91] max 0.063 [1.60] 3.00 [76.20] 0.025 [0.64] 0.10 [2.54] 0.09 [2.30] max 0.10 [2.54] 0.65 [16.51] 0.15 [3.81] 1.4 [35.56] 1 234 5 6 7 8 91011 Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. ©2003 Bel Fuse Inc. Pin Function 1 +Vo 2 +Vo 3 Remote Sense 4 +Vo 5 Ground 6 Ground 7 +Vin 8 +Vin 9 Not Used 10 Trim 11 Remote On/Off Specifications subject to change without notice. 01.03 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 14