BRIGHT LED ELECTRONICS CORP. LED LAMPS SPECIFICATION ●COMMODITY：AXIAL TYPE LAMP ●DEVICE NUMBER：BL-XJF361-TR7 ●ELECTRICAL AND OPTICAL CHARACTERISTICS (Ta=25℃) Chip Peak Dominant Wave Want Length Length λp (nm) λd(nm) Emitted Color Super Amber 610 605±5 PAGE: 2 REVISION: 1.0 Absolute Maximun Rating Lens Electro-optical Data (At 20mA) Vf(V) Iv(mcd) Appearance Δλ Pd If Peak (nm) (mW) (mA) If(mA) Typ. Max. Min Typ. Water Clear 17 100 30 100 2.0 2.6 Viewing Angle 2θ1/2 (deg) 63.0 150.0 35 Remark：1.Viewing angle is the Off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. This product doesn’t contain restriction Substance, comply ROHS standard. ●ABSOLUTE MAXIMUN RATINGS (Ta=25℃) Reverse Voltage ………………………………………..……………………………….…..……………………….… 5V Reverse Current (VR=5V) …………………………………………….………………………………………….. 100µA Operating Temperature Range ……………………………………………..……….……………..…… -25℃ ～ 80℃ Storage Temperature Range ……………………………………………………………………..…… -30℃ ～ 85℃ Lead Soldering Temperature ………………………………..……………..……………………… 260℃ For 5 Seconds ●PACKAGE DIMENSIONS NOTES: 1.All dimensions are in millimeters (inches). 2.Tolerance is ±0.25mm (0.01”) unless otherwise specified. 3.Lead spacing is measured where the leads emerge from the package. 4.Specifications are subject to change without notice. BRIGHT LED ELECTRONICS CORP. LED LAMP SPECIFICATION ●COMMODITY：AXIAL TYPE LED LAMP ●DEVICE NUMBER：BL-XJF361-TR7 PAGE: REVISION: 3 1.0 BRIGHT LED ELECTRONICS CORP. AXIAL LED LAMP SPECIFICATION ●COMMODITY：AXIAL TYPE LED LAMP ●DEVICE NUMBER：BL-XJF361-TR7 PAGE: ● TAPPING AND PACKAGING SPECIFICA RERSION: 1.0 4 SPECIFICATION ITEM SYMBOL Minimum Maximum mm inch mm inch Tape Feed Hole Diameter (DIA) D0 1.40 0.055 1.55 0.061 Feed Hole Location E 1.65 0.065 1.85 0.072 Centers Line Dimensions Length Direction F 5.45 0.215 5.55 0.218 Compartment Depth K0 3.10 0.122 3.30 0.130 Carrier Tape Overall Thickness K 3.00 0.118 3.20 0.126 Compartment Pitch P 3.90 0.153 4.10 0.161 Sprocket Hole Diameter P0 3.90 0.153 4.10 0.161 Centers Line Dimensions Length Direction P2 1.95 0.076 2.05 0.080 Carrier Tape Thickness t － － 0.30 0.012 Carrier Tape Width W 12.00 0.472 12.30 0.484 Flange Diameter A 178.0 7.008 180.0 7.087 Hub Spindle Hole C 12.50 0.492 13.50 0.531 Hub Diameter D2 20.00 0.788 21.50 0.846 Fixing Tape Width W1 9.00 0.354 9.30 0.366 Flange Space Between Flanges T 16.00 0.629 17.00 0.669 Compartment Length A0 2.20 0.087 2.40 0.094 Compartment Width B0 3.90 0.154 4.10 0.161 e d o n A e d o h t a C BRIGHT LED ELECTRONICS CORP. SURFACE MOUNT CHIP LED LAMP SPECIFICATION RELIABILITY TEST Classification Test Item Reference Standard Operation Life MIL-STD-750:1026 MIL-STD-883:1005 JIS C 7021 :B-1 High Temperature MIL-STD-202:103B High Humidity JIS C 7021 :B-11 Endurance Storage Test High MIL-STD-883:1008 Temperature JIS C 7021 :B-10 Storage Low Temperature JIS-C-7021 :B-12 Storage Temperature MIL-STD-202:107D Cycling MIL-STD-750:1051 MIL-STD-883:1010 JIS C 7021 :A-4 Thermal Shock MIL-STD-202:107D Environmental MIL-STD-750:1051 Test MIL-STD-883:1011 Solder MIL-STD-202:201A Resistance MIL-STD-750:2031 JIS C 7021 :A-1 PAGE: REVISION: Test Conditions Connect with a power If=20mA Ta=Under room temperature Test time=1,000hrs Ta=+65℃±5℃ RH=90%-95% Test time=240hrs 5 1.0 Result 0/20 0/20 High Ta=+85℃±5℃ Test time=1,000hrs 0/20 Low Ta=-35℃±5℃ Test time=1,000hrs 0/20 -35℃ ~ +25℃ ~ +85℃ ~ +25℃ 60min 20min 60min 20min Test Time=5cycle -35℃±5℃ ~+85℃±5℃ 20min 20min Test Time=10cycle Preheating： 140℃-160℃,within 2 minutes. Operation heating： 235℃(Max.), within 10seconds. (Max.) 0/20 0/20 0/20 JUDGMENT CRITERIA OF FAILURE FOR THE RELIABILITY Measuring items Forward voltage Reverse current Luminous intensity Note: Symbol VF ( V) Ir(uA) Iv ( mcd ) Measuring conditions If=20mA Vr=5V If=20mA 1.U means the upper limit of specified characteristics. Judgement criteria for failure Over Ux1.2 Over Ux2 Below SX0.5 S means initial value. 2.Measurment shall be taken between 2 hours and after the test pieces have been returned to normal ambient conditions after completion of each test. BRIGHT LED ELECTRONICS CORP. SURFACE MOUNT CHIP LED LAMP SPECIFICATION PAGE: REVISION: 1. 6 1.0 SOLDERING: ● Manual Of Soldering The temperature of the iron tip should not be higher than 300℃(572℉) and Soldering within 3 seconds per solder-land is to be observed. ● Reflow Soldering Preheating : 140℃~160℃±5℃,within 2 minutes. Operation heating : 235℃(MAX.) within 10 seconds.(Max) Gradual Cooling (Avoid quenching). 10 SEC. MAX. TEMPERATURE 140~160℃ 235℃ MAX. 4℃ /SEC. MAX. 4℃ /SEC. MAX. OVER 2 MIN. TIME ● DIP soldering (Wave Soldering) Preheating : 120℃~150℃,within 120~180 sec. Operation heating : 245℃±5℃ within 5 sec.260℃ (Max) Gradual Cooling (Avoid quenching). Soldering heat Max. 260 ℃ TEMPERATURE 245 ±5℃ within 5 sec. 120~150℃ Preheat 120~180 sec. TIME 2. Handling : Care must be taken not to cause to the epoxy resin portion of BRIGHT LEDs while it is exposed to high temperature. Care must be taken not rub the epoxy resin portion of BRIGHT LEDs with hard or sharp article such as the sand blast and the metal hook.