Cree® P4 LED Model # LP476THR1-90G-01 Data Sheet 90-degree, 7.6 x 7.6 mm LED lamp in red color with water-transparent lens and stopper Applications • • • Advertising Signs Indicators Automotive Lighting Absolute Maximum Ratings (TA = 25°C) Items Symbol Absolute Maximum Rating Unit IF 70 mA IFP 200 mA Reverse Voltage VR 5 V Power Dissipation PD 220 mW Operation Temperature Topr -40 ~ +100 °C Storage Temperature Tstg -40 ~ +100 °C Lead Soldering Temperature Tsol Forward Current Note 2 Peak Forward Current Note 1 Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) Notes: 1. 2. Pulse width ≤0.1 msec, duty ≤1/10. A heat sink is recommended if the device is operated at ambient temperatures higher than 25°C. D-CT137.000 Data Sheet: CL Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Symbol Condition Unit Forward Voltage VF IF = 70 mA V Reverse Current IR VR = 5 V μA Dominant Wavelength λD IF = 70 mA nm 620 628 Luminous Flux ΦV IF = 70 mA mlm 1520 3000 2θ½H-H IF = 70 mA deg 90 2θ½V-V IF = 70 mA deg 35 50% Power Angle Minimum Subject to change without notice. www.cree.com/ledlamps Typical Maximum 2.6 3.2 100 637 Standard Bins for LP476THR1-90G-01 (IF = 70 mA) Lamps are sorted to luminous intensity (IV), VF and dominant wavelength (λD) bins shown. Orders for LP476THR1-90G-01 may be filled with any or all bins contained as below. All luminous intensity (IV), VF and dominant wavelength (λD) values shown and specified are at IF = 70 mA. Y or above 5860 mcd Luminous Intensity (IV) X 4180 mcd W 3000 mcd V 2130 mcd U 1520 mcd 620 nm 637 nm Dominant Wavelength (λD) Forward Voltage (VF) Rank Voltage V4 V5 V6 V7 V8 2.2-2.4 V 2.4-2.6 V 2.6-2.8 V 2.8-3.0 V 3.0-3.2 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Tolerance of measurement of luminous intensity is ±15%. 3. Tolerance of measurement of dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT137.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LP476THR1-90G-01 Rev. No. 02 Graphs Graphs 100.0 -50 -60 If (mA) -40 -30 -10 -20 0.0 Vr(V) 80.0 -10.0 60.0 -20.0 40.0 -30.0 20.0 -40.0 0.0 2.0 2.2 2.4 2.6 2.8 3.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Vf(V) Ir(uA) -50.0 FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. 2.5 Half Power WL=23nm Domi WL= 628nm I (RELATIVE LUMINOUS INTENSITY) 100% 2.0 75% 1.5 50% 1.0 25% 0.5 If(mA) 0.0 0.0 20.0 40.0 60.0 80.0 100.0 FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT. WL(nm) 0% 400 500 600 700 800 900 FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. H-H : 90 V-V : 35 50% Power Angle : 100 IF(mA) H-H V-V Ie(%) 0 80 100% 60 80% 60% 40 40% 20 20% 0 Ta( C) 0 20 40 60 80 100 120 -90 FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) Items Signatures Date Prepared by LiuZM 2005-05-18 Rev. No Checked by Aldosin 2005-05-18 02 Approved by David 2005-05-18 FCN# -60 -30 0 30 60 90 0% FIG.6 FAR FIELD PATTERN Revision History Date Change Description 2005-05-18 Release. Change OD(max)635 to 637nm; IV from V,,W,X,Y(typ)4000 to U,V,W,X(typ)4000mcd. FCN20050163 Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT137.000 4/4 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Format #: COTCO-D-074 REV.4 Mechanical Dimensions Document No. SPE/LP476THR1-90G-01 All dimensions are in mm. Tolerance isRev. ±0.25No. mm unless otherwise 02 noted. An epoxy meniscus may extend about 1.5 mm down the leads. Dimmay ens n mm Dramax. wing Burr around bottom of epoxy beio 0.5 e maximum ating Unit 70 mA 200 mA 5 V 220 mW ~ +100 °C ~ +100 °C 0°C forNotes 5 sec Max. he base RoHS of theCompliance epoxy bulb) The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted at materials in this product are below the than maximum concentration values (also referred to as the the device is operated ambient temperatures higher 25 deg C. For long term threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Direc- tive 2002/95/EC on the restriction of the use of certain hazardous in electrical and electronic equipment A and 50mA are recommended. Please contact COTCO sales substances representative for more . (RoHS), as amended through April 21, 2006. Vision Advisory Claim = 2should 5°C) be cautioned not to stare at the light of this LED product. The bright light can damage the eye. cs ( TaUsers Condition Min. Typ. Max. Unit Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the are registered trademarks of Cree, Inc. Cree logo IF = 70mA --- CLD-CT137.000 2.6 3.2 V Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color 1: Full-color distribution 2~9, A~Z . . . : special request * aaaaaaaaa-aaa-aa- x x x x x IV 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type 0: Standard = tube pack 1~9, A~Z . . . : special request * Product P/N * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number Description LP476THR1-90G-01-00001 P4 90 High Red 628nm, FULL RANK, Tube Pack LP476THR1-90G-01-00011 P4 90 High Red 628nm, V or above, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT137.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps