CCLD-023 5x7mm SMD LVDS Clock Oscillator 2.5 Volts Model CCLD-023 is a 77.760Mhz to 161.000MHz LVDS Clock Oscillator operating at 2.5Volts. The oscillator utlizes a High Q Third Overtone crystal design providing very low Jitter and Phase Noise. No Sub-Harmonics are present in the Output Signal. 5x7mm SMD Applications: Digital Video SONET/SDH/DWDM Storage Area Networks Broadband Access Ethernet, Gigabit Ethernet Rev.: C Date: 10-10-07 CCLD-023 5x7mm SMD LVDS Clock Oscillator Frequency Range: 77.760Mhz to 161.000Mhz Temperature Range: (standard) (Option M) (Option X) 0°C to +70°C -20°C to +70°C -40°C to +85°C Storage: Input Voltage: Input Current: -55°C to 120°C 2.5V ± 0.125V 43mA Typ., 63mA Max Output: Symmetry: Rise/Fall Time: Differential LVDS 45/55% Max @ 50%Vdd 1nsec Max @ 20% to 80% Vdd Frequency Stability Options(ppm): ±20, ±25, ±50, ±100 Load: 100 Ohms Connected between OUT and COUT Logic: Output Voltage Levels “0”=0.90 Min., 1.10 Typ. “1”=1.43 Typ., 1.60 Max Differential Output Voltage: 247mV Min., 454mV Max Disable Time 200nSec Max Enable Time 2mSec Max Phase Jitter: 12KHz~80MHz 0.5psec Typ., 1psec RMS Max Phase Noise: (See Plot Below) Sub-harmonics: None Aging: <3ppm 1st/yr, <1ppm every year thereafter Typical Phase Noise Plot Rev.: C Date: 10-10-07 CCLD-023 5x7mm SMD LVDS Clock Oscillator PART NUMBER GUIDE CCLD - 023 X - 50 - 155.520 #1 #2 #3 #4 #5 #1 Crystek LVDS Osc. #2 Model 023 #3 Temp. Range (Blank=0/70°C)(M=-20/70°C)(X=-40/85°C) #4 Stability: (see Table 1) #5 Frequency in MHz: 3 or 6 decimal places Stability Indicator Blank(std) ±100ppm 50 ±50ppm 25 ±25ppm 20 ±20ppm Example: CCLD-023X-50-155.520 2.5V, -40/85°C, ±50ppm, 155.520 MHz Shock: Solderability: Vibration: Solvent Resistance: Resistance to Soldering Heat: RECOMMENDED REFLOW SOLDERING PROFILE MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 2007, Condition A MIL-STD-202, Method 215 MIL-STD-202, Method 210, Condition I or J Ramp-Up 3°C/Sec Max. 260°C 217°C 200°C 150°C Environmental: Preheat 180 Secs. Max. 8 Minutes Max. Thermal Shock: MIL-STD-883, Method 1011, Condition A Moisture Resistance: MIL-STD-883, Method 1004 90 Secs. Max. 260°C for 10 Secs. Max. NOTE: Reflow Profile with 240°C peak also acceptable. 0.274 ±0.007 (6.96 ±0.18) Tri-State Function Part Number Frequency DC Lot Code 0.193 ±0.007 (4.90 ±0.18) SUGGESTED PAD LAYOUT 0.055 Typ (1.40 Typ) 0.045 ±0.008 (1.14 ±0.20) #1 #2 #3 #6 #5 #4 0.045 ±0.008 (1.14 ±0.20) Pin #1 State Output State Open or N/C Active “0”level 0.3*Vcc Max High Z “1” level 0.7*Vcc Min Denotes pad 1 0.100 (2.54) 0.200 (5.08) Critical Temperature Zone Ramp-Down 6°C/Sec. TEMPERATURE Mechanical: Table 1 Pad 0.071 SQ (1.80) 1 0.148 (3.75) 0.200 (5.08) 0.01uF Bypass Capacitor Recommended Active Connection Enable/Disable 2 N/C 3 GND 4 Out 5 Comp. Out 6 VCC Rev.: C Date: 10-10-07