CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts HER1601 THRU HER1606 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage TO-220A .180 3.8 f +.2 HOLE THRU (4.6) .412 (10.5) MAX. .108 (2.75) .248 (6.3) .595 (15.1) MAX. .040 (1.0) MAX. .550 .158 (14.0) (4.0) MIN. MAX. .051 MAX. (1.3) .040 MAX. (1.0) Mechanical Data · Case : JEDEC TO-220A molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram .050 (1.27) PIN 1 + .200 (5.08) + CASE PIN 2 Case Positive PIN 1 .120 (3.05) + CASE PIN 2 Case Negative Suffix "R" Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols HER 1601 HER 1602 HER 1603 HER 1604 HER 1605 HER 1606 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 300 400 600 Volts Maximum RMS voltage VRMS 35 70 140 210 280 420 Volts Maximum DC blocking voltage VDC 50 100 200 300 400 600 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100℃ I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 200 Amps Maximum instantaneous forward voltage at 8.0A VF 1.0 1.3 Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=125℃ 1.7 Volts 10.0 μA IR 100 Maximum reverse recovery time (Note 1) Trr 50 80 ns Typical junction capacitance (Note 2) CJ 80 50 pF Typical thermal resistance (Note 3) RθJC Operating junction and storage temperature range TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. 2.2 -55 to +150 -55 to +150 ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES HER1601 THRU HER1606 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 AND TEST CIRCUIT DIAGRAM trr NONINDUCTIVE DUT (+ ) 50Vdc (approx) (-) NONINDUCTIVE +0.5A PULSE GENERATOR ( NOTE 2 ) -1.0A 1cm . FIG 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING 1000 20 8 4 0 50 100 CASE TEMPERATURE . ( % ) 150 FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT Tj=25oC 120 8.3ms Single Half Sine Wave JEDEC Method INSTANTAN EOUS REVERSE CURRET . ( 12 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS 60 10 Tj=25 C O 1 0.1 20 40 60 80 100 120 140 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 100 o 160 HE 120 HE 80 40 1 R1 60 2 R1 60 1-1 6 60 5 0.3 10 20 50 100 200 REVERSE VOLTAGE . ( V) 500 1000 5 60 0.1 Tj=25oC Pulse Width=300 1% Duty Cycle 0.03 .010.4 5 R1 6 1.0 60 Tj=25 C 3.0 R1 200 10 HE FIG . 5 -TYPICAL JUNCTIOON CAPACITANCE PER LEG 30 4 1 00 HE 50 60 5 10 20 NMBER OF CYCLES AT 60Hz 1-1 2 60 1 R1 30 0 O PERCENT OF RATED PEAK REVERSE VOLTAGE . (%) 90 240 Tj=125 C 100 HE 0 SET TIME BASE FOR 5/ 10ns / cm A) 16 INSTANTANEOUS FORWARD CURRENT . ( A) AVERAGE FORWARD CURRENT . ( A ) PE A K F O R W A R D S U R G E C U R R E N T . ( A ) -0.25A OSCILLOSCOPE (NOTE 2 ) NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISETIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf CAPACITANCE ( pF) 0 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE . ( V ) s 1.8