CURRENT 35.0 Amperes VOLTAGE 50 to 1000 Volts KBPC35005/W THRU KBPC3510/W Features · Diffused Junction · Low Reverse Leakage Current · Low Power Loss, High Efficiency · Surge Overload Rating to 400A Peak · Electrically Isolated Metal Case for Maximum Heat Dissipation · High Case Dielectric Strength of 1500VRMS K B PC K B P C -W H H B N E M L A A C H P H (AC) (+) (AC) (+) J C Mechanical Data A P K (AC) (-) (-) (AC) G · Case : High Conductivity Metal · Terminals : Plated Leads Solderable per MIL-STD-202, Method 208 · Polarity : Symbols Marked on Case · Mounting : Through Hole for #10 Screw · Mounting Torque : 8.0 Inch-pounds Maximum · Weight : KBPC 31.6 grams (approx.) KBPC-W 28.5 grams (approx.) · Mounting Position : Any · Marking : Type Number Dim A B C E G H K B P C / K B P C -W Min Max Dim Min J 28.40 28.70 17.10 10.40 10.97 11.23 K 15.50 17.60 0.97 O/ L M 22.86 25.40 30.50 N 13.30 15.30 10.97 P Hole for #10 s crew 17.10 4.85 O/ 5.59 O/ A ll Dimens ions in mm Max 19.10 12.40 1.07 O/ 11.23 19.10 "W" S uffix Des ignates Wire Leads No S uffix Des ignates F as t-on T erminals Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols KBPC35 KBPC35 KBPC35 KBPC35 KBPC35 KBPC35 KBPC35 005/W 01/W 02/W 04/W 06/W 08/W 10/W Units Peak Repetitive Reverse voltage Working Peak Reverse voltage DC Blocking voltage VRMM VRWM VR 50 100 200 400 600 800 1000 Volts RMS Reverse voltage VR(RMS) 35 70 140 280 420 560 700 Volts Io 35 Amps Non-Repetitive Peak Forward Surge Current, 8.3ms single half-sine-wave superimposed on rated load (JEDEC method) IFSM 400 Amps Forward voltage (per element) @ IF=17.5 A VFM 1.2 Volts Peak Reverse Current at Rated DC Blocking voltage @ TC=25℃ 10 μA Average Rectified Output Current @ TC=55℃ IR 1.0 mA I2t Rating for Fusing (t<8.3ms) (Note 2) I2t 664 A2S Typical Junction Capacitance (Note 3) Cj 300 pF RθJA 2.7 ℃/W -65 to +150 ℃ @ TC=125℃ Typical Thermal Resistance Junction to Case Operating and Storage Temperature Range Tj TSTG Notes: (1) Thermal resistance junction to case mounted on heat sink. (2) Measured at non-repetitive, for t > 1.0ms and < 8.3ms. (3) Measured at 1.0MHz and applied reverse voltage of 4.0V DC. A RATINGS AND CHARACTERISTIC CURVES KBPC35005/W THRU KBPC3510/W I F , INST ANT ANEOUS FOR WARD CURRENT I F , AVERAGE FOR WARD CURRENT (A) Mounted on a 220 x 220 x 50mm AL plate heatsink 30 20 10 Resistive or Inductive load 0 0 25 50 75 100 125 100 (A) 40 10 1.0 0.1 T j = 25 C 0.01 0 150 CURRENT (µA) 300 I R , INST ANT ANEOUS REVERSE (A) CURRENT I FSM , PEAK FOR WARD. SURGE Single Half-Sine Wave (JEDEC Method) 200 100 T j = 150 C 0 1 10 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 V F , INST ANT ANEOUS FOR WARD VOL TAGE (V) Fi g. 2 Typical Forward Characteristics (per element) T C , CASE TEMPERA TURE ( C ) Fi g. 1 Forward. Current Deratin g Curve. 400 Pulse Width = 300 s 100 NUMBER OF CYCLES AT 60 Hz Fi g. 3 Maximum Non-Repetitive Sur ge Current 10 T j = 100 C 1.0 T j = 25°C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RA TED PEAK REVERSE VOL TAGE (%) Fi g. 4 Typical Reverse Characteristics (per element )