CURRENT 10.0Amperes VOLTAGE 20 to 100 Volts SBP1020 THRU SBP10100 Features · Plastic Package has Underwriters Laboratory Flammability Classification 94V-0 · Metal silicon junction, majority carrier conduction · Guard ring for overvoltage protection · Low power loss, high efficiency · High current capability, Low forward voltage drop · High surge capability · For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications · Dual rectifier construction · High temperature soldering guaranteed : 250℃/10 seconds, 0.25" (6.35mm) from case ITO-220 2.54 · Case : JEDEC ITO-220 molded plastic body · Terminals : Lead solderable per MIL-STD-750, Method 2026 · Polarity : As marked. No suffix indicates Common Cathode, suffix "A" indicates Common Anode · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram 0.7 2.54 0.2 PIN 1 PIN 3 Positive CT Suffix "C" 4.5 0.2 15 0.3 2.7 0.2 13Min 2.7 0.2 1.3 0.2 3.7 0. 2 Mechanical Data 0.2 0.1 3.2 6.4 0.1 10 0.5 0.2 0.5 2.4 0.2 0.2 0.2 PIN 1 + CASE PIN 2 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, single phase, half wave, resistive or inductive load. For capacitive load, derate by 20%) Symbols SBP 1020 SBP 1030 SBP 1040 SBP 1050 SBP 1060 SBP 1080 SBP 10100 Units Maximum repetitive peak reverse voltage VRRM 20 30 40 50 60 80 100 Volts Maximum RMS voltage VRMS 14 21 28 35 42 56 70 Volts Maximum DC blocking voltage VDC 20 30 40 50 60 80 100 Volts Maximum average forward rectified current (see Fig. 1) I(AV) 10.0 Amps Repetitive peak forward current(square wavr, 20KHZ) at Tc=105℃ IFRM 20.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150.0 Amps Maximum instantaneous forward voltage at 5.0A (Note 1) VF Maximum instantaneous reverse current at rated DC blocking voltage (Note1) IR TA=25℃ Operating junction temperature range Storage temperature range Notes: (1) Pulse test: 300μS pulse width, 1% duty cycle (2) Thermal resistance from junction to case 0.75 0.80 0.85 Volts 1.0 TA=100℃ Typical thermal resistance (Note 2) 0.65 50 RθJC TJ TSTG 25 ℃/W 5.0 -65 to +125 -65 to +150 -65 to +150 mA ℃ ℃ RATINGS AND CHARACTERISTIC CURVES SBP1020 THRU SBP10100 FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG.1-FORWARD CURRENT DERATING CURVE 150 4.0 3.0 2.0 ── SBP1020-SBP1040 - - - SBP1050-SBP10100 1.0 0 0 20 40 60 TJ=TJMAX 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 125 RESISTIVE OR INDUCTIVE LOAD 0.375"(9.5MM) LEAD LENGTH 80 100 120 150 PEAK FORWARD SURGE CURRENT (AMPERES) AVERAGE FORWARD CURRENT AMPERES 5.0 100 75 50 25 0 1 10 100 LEAD TEMPERATURE (℃) NUMBER OF CYCLES AT 60Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 20 10 TJ=150℃ TJ=125℃ TJ=125℃ 10 INSTANTANEOUS REVERSE CURRENT MILL (AMPERES) INSTANTANEOUS FORWARD CURRENT (AMPERES) 50 ㎲ PULSE WIDTH=300 1% DUTY CYCLE 1 TJ=25℃ 0.1 ── SBP1020-SBP1040 - - - SBP1050-SBP10100 1 TJ=75℃ 0.1 0.01 TJ=25℃ 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 ── SBP1020-SBP1040 - - - SBP1050-SBP10100 0.001 0 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TJ=25℃ f=1.0MHz Vsig=50mVp-p 1000 ── SBP1020-SBP1040 - - - SBP1050-SBP10100 100 0.1 1 10 REVERSE VOLTAGE. VOLTS 100 TRANSIENT THERMAL IMPEDANCE,℃/ W JUNCTION CAPACITANCE (pF) 4000 10 1 0.1 0.01 0.1 1 T, PULSE DURATION, sec. 10 100