DS2430A 256-Bit 1-Wire EEPROM ORDERING INFORMATION N ot R ec DS2430A TO-92 Package DS2430AP 6-pin TSOC Package DS2430A/T&R TO-92 Package, Tape & Reel DS2430AP/T&R TSOC Package, Tape & Reel DS2430A+ TO-92 Package DS2430AP+ 6-pin TSOC Package DS2430A+T&R TO-92 Package, Tape & Reel DS2430AP+T&R TSOC Package, Tape & Reel DS2430AX Flip Chip, 10k Tape & Reel DS2430AX-S Flip Chip, 2.5k Tape & Reel + Indicates lead-free compliance. es i D ew 1 2 1 6 2 5 3 4 TOP VIEW 3.7mm x 4.0mm x 1.5mm rN d TSOC PACKAGE DALLAS DS2430A de TO-92 en PIN ASSIGNMENT 256-bit Electrically Erasable Programmable Read Only Memory (EEPROM) plus 64-bit one-time programmable application register Unique, factory-lasered and tested 64-bit registration number (8-bit family code + 48-bit serial number + 8-bit CRC tester) assures absolute identity because no two parts are alike Built-in multidrop controller ensures compatibility with other MicroLAN products EEPROM organized as one page of 32 bytes for random access Reduces control, address, data, and power to a single data pin Directly connects to a single port pin of a microprocessor and communicates at up to 16.3kbits per second 8-bit family code specifies DS2430A communication requirements to reader Presence detector acknowledges when reader first applies voltage Low cost TO-92 or 6-pin TSOC and Flip Chip surface mount package Reads and writes over a wide voltage range of 2.8V to 6.0V from -40°C to +85°C om m fo FEATURES gn www.maxim-ic.com SIDE VIEW See Mech. Drawing Section 4 3 3 2430A rrd#xx 1 2 3 1 2 Flip Chip, Top View with Laser Mark, Contacts Not Visible. “rrd” = Revision/Date #xx = Lot Number See 56-G7016-001 for package outline. BOTTOM VIEW See Mech. Drawings Section NOTE: The leads of TO-92 packages on tapeand-reel are formed to approximately 100 mil (2.54 mm) spacing. For details refer to drawing 56-G0006-003. PIN DESCRIPTION Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 1 of 16 TO-92 Ground Data NC –––– –––– –––– TSOC Ground Data NC NC NC NC Flip Chip Ground Data NC NC –––– –––– 080807 DS2430A DESCRIPTION D es i gn The DS2430A 256-bit 1-Wire EEPROM identifies and stores relevant information about the product to which it is associated. This lot or product specific information can be accessed with minimal interface, for example a single port pin of a microcontroller. The DS2430A consists of a factory-lasered registration number that includes a unique 48-bit serial number, an 8-bit CRC, and an 8-bit Family Code (14h) plus 256 bits of user-programmable EEPROM and a 64-bit one-time programmable application register. The power to read and write the DS2430A is derived entirely from the 1-Wire® communication line. Data is transferred serially via the 1-Wire protocol, which requires only a single data lead and a ground return. The 48-bit serial number that is factory-lasered into each DS2430A provides a guaranteed unique identity that allows for absolute traceability. The TO-92 and TSOC packages provide a compact enclosure that allows standard assembly equipment to handle the device easily for attachment to printed circuit boards or wiring. Typical applications include storage of calibration constants, board identification, and product revision status. ew OVERVIEW de d fo rN The block diagram in Figure 1 shows the relationships between the major control and memory sections of the DS2430A. The DS2430A has four main data components: 1) 64-bit lasered ROM, 2) 256-bit EEPROM data memory with scratchpad, 3) 64-bit one-time programmable application register with scratchpad and 4) 8-bit status memory. The hierarchical structure of the 1-Wire protocol is shown in Figure 2. The bus master must first provide one of the four ROM Function Commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4) Skip ROM. The protocol required for these ROM Function Commands is described in Figure 8. After a ROM Function Command is successfully executed, the memory functions become accessible and the master can provide any one of the four memory function commands. The protocol for these memory function commands is described in Figure 6. All data is read and written least significant bit first. 64-BIT LASERED ROM N ot R ec om m en Each DS2430A contains a unique ROM code that is 64 bits long. The first 8 bits are a 1-Wire family code (14h). The next 48 bits are a unique serial number. The last 8 bits are a CRC of the first 56 bits. (Figure 3). The 1-Wire CRC is generated using a polynomial generator consisting of a shift register and XOR gates as shown in Figure 4. The polynomial is X8 + X5 + X4 + 1. Additional information about the Dallas 1-Wire Cyclic Redundancy Check is available in Application Note 27. The shift register bits are initialized to 0. Then starting with the least significant bit of the family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC value. Shifting in the 8 bits of CRC should return the shift register to all 0s. 1-Wire and iButton are registered trademarks of Dallas Semiconductor. 2 of 16 DS2430A N ot R ec om m en de d fo rN ew D es i gn DS2430A BLOCK DIAGRAM Figure 1 3 of 16 DS2430A om m en de d fo rN ew D es i gn HIERARCHICAL STRUCTURE FOR 1-WIRE PROTOCOL Figure 2 64-BIT LASERED ROM Figure 3 ec 8-Bit CRC Code LSB MSB 8-Bit Family Code (14H) LSB MSB LSB R MSB 48-Bit Serial Number Polynomial = X8 + X5 + X4 + 1 N ot 1-WIRE CRC GENERATOR Figure 4 4 of 16 DS2430A MEMORY es i gn The memory of the DS2430A consists of three separate sections, called data memory, application register, and status register (Figure 5). The data memory and the application register each have its own intermediate storage area called scratchpad that acts as a buffer when writing to the device. The data memory can be read and written as often as desired. The application register, however, is one-time programmable only. Once the application register is programmed, it is automatically write protected. The status register will indicate if the application register is already locked or if it is still available for storing data. As long as the application register is unprogrammed, the status register will read FFh. Copying data from the register scratchpad to the application register will clear the 2 least significant bits of the status register, yielding an FCh the next time one reads the status register. en de d fo rN ew D DS2430A MEMORY MAP Figure 5 om m MEMORY FUNCTION COMMANDS The Memory Function Flow Chart (Figure 6) describes the protocols necessary for accessing the different memory sections of the DS2430A. An example is shown later in this document. WRITE SCRATCHPAD [0Fh] ot R ec After issuing the Write Scratchpad command, the master must first provide a 1-byte address, followed by the data to be written to the scratchpad for the data memory. The DS2430A will automatically increment the address after every byte it received. After having received a data byte for address 1Fh, the address counter will wrap around to 00h for the next byte and writing continues until the master sends a Reset Pulse. READ SCRATCHPAD [AAh] N This command is used to verify data previously written to the scratchpad before it is copied into the final storage EEPROM memory. After issuing the Read Scratchpad command, the master must provide the 1byte starting address from where data is to be read. The DS2430A will automatically increment the address after every byte read by the master. After the data of address 1Fh has been read, the address counter will wrap around to 00h for the next byte and reading continues until the master sends a Reset Pulse. 5 of 16 DS2430A en COPY SCRATCHPAD [55h] de d fo rN ew D es i gn MEMORY FUNCTION FLOW CHART Figure 6 om m After the data stored in the scratchpad has been verified the master may send the Copy Scratchpad command followed by a validation key of A5h to transfer data from the scratchpad to the EEPROM memory. This command will always copy the data of the entire scratchpad. Therefore, if one desires to change only a few bytes of the EEPROM data, the scratchpad should contain a copy of the latest EEPROM data before the Write Scratchpad and Copy Scratchpad commands are issued. After this command is issued, the data line must be held at logic high level for at least 10ms. ec READ MEMORY [F0h] N ot R The Read Memory command is used to read a portion or all of the EEPROM data memory and to copy the entire data memory into the scratchpad to prepare for changing a few bytes. To copy data from the data memory to the scratchpad and to read it, the master must issue the read memory command followed by the 1-byte starting address from where data is to be read from the scratchpad. The DS2430A will automatically increment the address after every byte read by the master. After the data of address 1Fh has been read, the address counter will wrap around to 00h for the next byte and reading continues until the master sends a Reset Pulse. If one intends to copy the entire data memory to the scratchpad without reading data, a starting address is not required; the master may send a Reset Pulse immediately following the command code. 6 of 16 DS2430A d fo rN ew D es i gn MEMORY FUNCTION FLOW CHART Figure 6 (cont’d) de WRITE APPLICATION REGISTER [99h] om m en This command is essentially the same as the Write Scratchpad command, but it addresses the 64-bit register scratchpad. After issuing the command code, the master must provide a 1-byte address, followed by the data to be written. The DS2430A will automatically increment the address after every byte it received. After having received a data byte for address 07h, the address counter will wrap around to 00h for the next byte and writing continues until the master sends a Reset Pulse. The Write Application Register command can be used as long as the application register has not yet been locked. If issued for a device with the application register locked, the data written to the register scratchpad will be lost. READ STATUS REGISTER [66h] N ot R ec The status register is a means for the master to find out if the application register has been programmed and locked. After issuing the read status register command, the master must provide the validation key 00h before receiving status information. The two least significant bits of the 8-bit status register will be 0 if the application register was programmed and locked; all other bits will always read 1. The master may finish the read status command by sending a Reset Pulse at any time. 7 of 16 DS2430A en de d fo rN ew D es i gn MEMORY FUNCTION FLOW CHART Figure 6 (cont’d) READ APPLICATION REGISTER [C3h] R ec om m This command is used to read the application register or the register scratchpad. As long as the application register is not yet locked, one will receive data from the register scratchpad. After the application register is locked the DS2430A will transmit data from the application register, making the register scratchpad inaccessible for reading. The contents of the status register indicate where the data received with this command came from. After issuing the Read Application Register command, the master must provide the 1-byte starting address from where data is to be read. The DS2430A will automatically increment the address after every byte read by the master. After the data of address 07h has been read, the address counter will wrap around to 00h for the next byte and reading continues until the master sends a Reset Pulse. COPY & LOCK APPLICATION REGISTER [5Ah] N ot After the data stored in the register scratchpad has been verified the master may send the Copy & Lock Application Register command followed by a validation key of A5h to transfer the contents of the entire register scratchpad to the application register and to simultaneously write-protect it. The master may cancel this command by sending a Reset Pulse instead of the validation key. After the validation key was transmitted, the application register will contain the data of the register scratchpad. Further write accesses to the application register will be denied. The Copy & Lock Application Register command can only be executed once. 8 of 16 DS2430A 1-WIRE BUS SYSTEM gn The 1-Wire bus is a system that has a single bus master and one or more slaves. In all instances, the DS2430A is a slave device. The bus master is typically a microcontroller. The discussion of this bus system is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal type and timing). A 1-Wire protocol defines bus transactions in terms of the bus state during specified time slots that are initiated on the falling edge of sync pulses from the bus master. Hardware Configuration rN ew D es i The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open drain connection or three-state outputs. The 1-Wire port of the DS2430A is open drain with an internal circuit equivalent to that shown in Figure 7. A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The DS2430A communicates at regular 1-Wire speed, 16.3kbits per second, and requires a pullup resistor as shown in Figure 7. The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus MUST be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low for more than 120µs, one or more of the devices on the bus may be reset. fo HARDWARE CONFIGURATION Figure 7 RPU N ot R ec om m en de d RPU Note: Depending on the 1-Wire communication speed and the bus characteristics, the optimal pullup resistor value will be in the 1.5kΩ to 5kΩ range. To write to a single device, a 2.2kΩ resistor and VPUP of at least 4.0V is sufficient. For writing multiple DS2430As simultaneously or operation at low VPUP, the resistor should be bypassed by a low-impedance pullup to VPUP while the device copies the scratchpad to EEPROM. 9 of 16 DS2430A N ot R ec om m en de d fo rN ew D es i gn ROM FUNCTIONS FLOW CHART Figure 8 10 of 16 DS2430A Transaction Sequence Initialization ROM Function Command Memory Function Command Transaction/Data es i gn The sequence for accessing the DS2430A via the 1-Wire port is as follows: INITIALIZATION ew D All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence consists of a Reset Pulse transmitted by the bus master followed by a Presence Pulse(s) transmitted by the slave(s). rN The Presence Pulse lets the bus master know that the DS2430A is on the bus and is ready to operate. For more details, see the 1-Wire Signaling section. ROM FUNCTION COMMANDS fo Once the bus master has detected a presence, it can issue one of the four ROM function commands. All ROM function commands are 8 bits long. A list of these commands follows (refer to flowchart in Figure 8): d Read ROM [33h] om m Match ROM [55h] en de This command allows the bus master to read the DS2430A’s 8-bit family code, unique 48-bit serial number, and 8-bit CRC. This command can be used only if there is a single DS2430A on the bus. If more than one slave is present on the bus, a data collision will occur when all slaves try to transmit at the same time (open drain will produce a wired-AND result). The resultant family code and 48-bit serial number will usually result in a mismatch of the CRC. ec The Match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a specific DS2430A on a multidrop bus. Only the DS2430A that exactly matches the 64-bit ROM sequence will respond to the subsequent memory function command. All slaves that do not match the 64-bit ROM sequence will wait for a Reset Pulse. This command can be used with a single or multiple devices on the bus. Skip ROM [CCh] N ot R This command can save time in a single-drop bus system by allowing the bus master to access the memory functions without providing the 64-bit ROM code. If more than one slave is present on the bus and a read command is issued following the Skip ROM command, data collision will occur on the bus as multiple slaves transmit simultaneously (open drain pulldowns will produce a wired-AND result). Search ROM [F0h] When a system is initially brought up, the bus master might not know the number of devices on the 1Wire bus or their 64-bit ROM codes. The Search ROM command allows the bus master to use a process of elimination to identify the 64-bit ROM codes of all slave devices on the bus. The Search ROM process is the repetition of a simple, three-step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master performs this simple, three-step routine on each bit of the ROM. 11 of 16 DS2430A After one complete pass, the bus master knows the contents of the ROM in one device. The remaining number of devices and their ROM codes may be identified by additional passes. See Application Note 187 for a comprehensive discussion of a search ROM, including an actual example. 1-Wire Signaling ew D es i gn The DS2430A requires strict protocols to insure data integrity. The protocol consists of four types of signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1 and Read Data. All these signals (except Presence Pulse) are initiated by the bus master. The initialization sequence required to begin any communication with the DS2430A is shown in Figure 9. A Reset Pulse followed by a Presence Pulse indicates the DS2430A is ready to accept a ROM command. The bus master transmits (TX) a Reset Pulse (tRSTL, minimum 480µs). The bus master then releases the line and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor. After detecting the rising edge on the data pin, the DS2430A waits (tPDH, 15µs to 60µs) and then transmits the Presence Pulse (tPDL, 60µs to 240µs). om m en de d fo rN INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 9 ec In order not to mask interrupt signaling by other devices on the 1-Wire bus, tRSTL + tR should always be less than 960µs. Read/Write Time Slots N ot R The definitions of write and read time slots are illustrated in Figure 10. All time slots are initiated by the master driving the data line low. The falling edge of the data line synchronizes the DS2430A to the master by triggering a delay circuit in the DS2430A. During write time slots, the delay circuit determines when the DS2430A will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit determines how long the DS2430A will hold the data line low overriding the 1 generated by the master. If the data bit is a “1”, the DS2430A will leave the read data time slot unchanged. 12 of 16 DS2430A READ/WRITE TIMING DIAGRAM Figure 10 ew D es i gn Write-1 Time Slot en de d fo rN Write-0 Time Slot N ot R ec om m Read-data Time Slot 13 of 16 DS2430A MEMORY FUNCTION EXAMPLE Example: Write 2 data bytes to data memory location 0006 and 0007. Read entire data memory. gn es i D Reset Presence CCh F0h 00h <32 Bytes> Reset Presence ew TX RX TX TX TX RX TX RX rN <Data Line High> fo TX COMMENTS Reset pulse (480µs to 960µs) Presence pulse Issue “Skip ROM” command Issue “Write Scratchpad” command Start address = 06h Write 2 bytes of data to scratchpad Reset pulse Presence pulse Issue “Skip ROM” command Issue “Read Scratchpad” command Start address = 06h Read scratchpad data and verify Reset pulse Presence pulse Issue “Skip ROM” command Issue “Copy Scratchpad” command Validation key Data line is held high for 10ms by the bus master to provide energy for copying data from the scratchpad to EEPROM Reset pulse Presence pulse Issue “Skip ROM” command Issue “Read Memory” command Start address = 00h Read EEPROM data page Reset pulse Presence pulse d DATA (LSB FIRST) Reset Presence CCh 0Fh 06h <2 Data Bytes> Reset Presence CCh AAh 06h <2 Data Bytes> Reset Presence CCh 55h A5h N ot R ec om m en de MASTER MODE TX RX TX TX TX TX TX RX TX TX TX RX TX RX TX TX TX 14 of 16 DS2430A ABSOLUTE MAXIMUM RATINGS* Voltage on DATA to Ground Operating Temperature Range Storage Temperature Range Soldering Temperature SYMBOL VIH VIL VOL VOH IL IP MIN 2.2 -0.3 SYMBOL CD MIN fo MIN 100k 10 de SYMBOL NCYCLE tDR en PARAMETER Write/Erase Cycles Data Retention (at 85°C) AC ELECTRICAL CHARACTERISTICS N ot SYMBOL tSLOT tLOW1 tLOW0 tLOWR tRDV tRELEASE tSU tREC tRSTH tRSTL tPDH tPDL tPROG om m R ec PARAMETER Time Slot Write 1 Low Time Write 0 Low Time Read Low Time Read Data Valid Release Time Read Data Setup Recovery Time Reset Time High Reset Time Low Presence Detect High Presence Detect Low Programming Time TYP d EEPROM VPUP 5 0.1 CAPACITANCE PARAMETER Capacitance TYP MAX +0.8 0.4 6.0 15 500 UNITS V V V V μA μA MAX 800 UNITS pF NOTES 1, 6 1, 9 1 1, 2 3 10 D PARAMETER Logic 1 Logic 0 Output Logic Low @ 4mA Output Logic High Input Load Current (DATA pin) Programming Current (-40°C to +85°C; VPUP = 2.8V to 6.0V) ew DC ELECTRICAL CHARACTERISTICS es i gn This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. rN * -0.5V to +7.0V -40°C to +85°C -55°C to +125°C See J-STD-020A Specification (tA = +25°C) NOTES 7 (VPUP = 5.0V; tA = +25°C) TYP MAX UNITS years NOTES (-40°C to +85°C; VPUP=2.8V to 6.0V) MIN 60 1 60 1 0 1 480 480 15 60 15 of 16 TYP 15 15 MAX 120 15 120 15 45 1 960 60 240 10 UNITS µs µs µs µs µs µs µs µs µs µs µs µs ms NOTES 13 13 11, 12 5 4 8 DS2430A NOTES: 1) All voltages are referenced to ground. 2) VPUP = external pullup voltage. gn 3) Input load is to ground. 4) An additional reset or communication sequence cannot begin until the reset high time has expired. es i 5) Read data setup time refers to the time the host must pull the 1-Wire bus low to read a bit. Data is guaranteed to be valid within 1μs of this falling edge. D 6) VIH is a function of the external pullup resistor and VPUP. rN ew 7) Capacitance on the data pin could be 800pF when power is first applied. If a 5kΩ resistor is used to pull up the data line to VPUP, 5μs after power has been applied the parasite capacitance will not affect normal communications. fo 8) The Reset Low Time (tRSTL) should be restricted to a maximum of 960μs, to allow interrupt signaling; otherwise it could mask or conceal interrupt pulses. d 9) Under certain low voltage conditions VILMAX may have to be reduced to as much as 0.5V to always guarantee a Presence Pulse. de 10) The Copy Scratchpad takes 10ms maximum, during which the voltage on the 1-Wire bus must not fall below 2.8V. en 11) Depending on the 1-Wire communication speed and the bus load characteristics, the optimal pullup resistor value will be in the 1.5kΩ to 5kΩ range. om m 12) The optimal sampling point for the master is as close as possible to the end time of the 15μs tRDV period without exceeding tRDV. For the case of a Read-One Time slot, this maximizes the amount of time for the pullup resistor to recover to a high level. For a Read-Zero Time slot, it ensures that a read will occur before the fastest 1-Wire device(s) releases the line. N ot R ec 13) The duration of the low pulse sent by the master should be a minimum of 1μs with a maximum value as short as possible to allow time for the pullup resistor to recover the line to a high level before the 1Wire device samples in the case of a Write-One Time or before the master samples in the case of a Read-One Time. 16 of 16