DOMINANT Semiconductors Innovating Illumination Power DomiLED TM DATA SHEET: Power DomiLEDTM InGaN White : DWW-UJG TM With its significant power in terms brightness, viewing angle and variety of application possibilities, Power DomiLED™ truly is a standout performer! Ideal for automotive interior lighting as well as home, office and industrial applications, it is also a proven performer in electronic signs and signals. Features: > > > > > > > High brightness surface mount LED. Long lifetime up to 50,000 hours due to silicone encapsulation. 120° viewing angle. Small package outline (LxWxH) of 3.2 x 2.8 x 1.8mm. Qualified according to JEDEC moisture sensitivity Level 2. Compatible to IR reflow soldering. Environmental friendly; RoHS compliance. Applications: > Automotive: interior applications, eg: switches, telematics, climate control system, dashboard, etc. exterior applications, eg: signal lighting, Center High Mounted Stop Light (CHMSL), > Display: full color display video notice board. > Industry: white goods (eg: Oven, microwave, etc.). > Lighting: architecture lighting, general lighting, garden light, etc © 2005 DomiLED is a trademark of DOMINANT Semiconductors. All rights reserved. Product specifications are subject to change without notice. 1 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Part Ordering Number Chip Technology / Color DWW-UJG-VW1-1 InGaN • DWW-UJG-V1 White Viewing Angle˚ 120 Total Flux @ IF=30mA, mlm 2100 - 4150 Luminous Intensity @ IF = 30mA IV (mcd) 715.0 - 1400.0 715.0 - 900.0 • DWW-UJG-V2 900.0 - 1125.0 • DWW-UJG-W1 1125.0 - 1400.0 NOTE 1. All part number above comes in a quantity of 2000 units per reel. 2. Other luminous intensity groups may also be available upon request. 3. Luminous intensity is measured with an accuracy of ± 11%. 4. Wavelength binning is carried for all units as per the wavelength-binning table. Only one wavelength group is allowed for each reel. 5. InGaN wavelength is very sensitive to drive current. Operating at lower current is not recommended and may yield unpredictable performance current pulsing should is used for dimming purposes. 6. An optional Vf bining is also available upon request. Bining scheme is as per following table. 6. Data provided for luminous flux is based on approximation. 2 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Electrical Characteristics at Ta=25˚C Part Number Min. (V) DWW 3.05 Vf @ If = 30mA Typ. (V) Max. (V) 3.40 Vr @ Ir = 10uA Min. (V) 5 4.00 Forward voltages are measure using a current pulse of 1 ms and with an accuracy of ± 0.1V. Vf Bining (Optional) Vf @ If = 30mA Forward Voltage (V) 3A 3.05 ... 3.35 30 3.35 ... 3.65 31 3.65 ... 3.95 32 3.95 ... 4.25 Forward voltage, Vf is measured with an accuracy of ± 0.1V. Please consult sales and marketing to incorporate special part number to incorporate Vf binning. Absolute Maximum Ratings Maximum Value Unit DC forward current 50 mA Peak pulse current; (tp ≤ 10µs, Duty cycle = 0.1) 200 mA Reverse voltage; Ir (max) = 10µA 5 V ESD Threshold (HBM) 2 kV 125 ˚C Operating temperature -40 … +110 ˚C Storage temperature -40 … +110 ˚C 200 mW LED junction temperature Power dissipation (at room temperature) 3 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination DWW, White Color Grouping Dominant White Bin Structure 0.44 0.42 0.40 0.38 0.36 0.34 0.32 0.30 0.28 0.26 0.24 0.27 • • • A1 A2 0.28 • • • 0.29 A3 A4 0.30 • • • C1 C2 • • • 0.31 • • • C3 C4 0.32 E1 E2 0.33 • • • 0.34 E3 E4 • • • 0.35 0.36 Chromaticity coordinate groups are measured with an accuracy of ± 0.01. W Bin A1 A2 A3 A4 C1 C2 C3 C4 0.2775 0.2900 0.2900 0.2775 Cy 0.2732 0.2939 0.3114 0.2907 Cx 0.2775 0.2900 0.2900 0.2775 Cy 0.2557 0.2764 0.2939 0.2732 Cx 0.2900 0.3025 0.3025 0.2900 Cy 0.2939 0.3146 0.3321 0.3114 Cx 0.2900 0.3025 0.3025 0.2900 Cy 0.2764 0.2971 0.3146 0.2939 Cx Cx 0.3025 0.3150 0.3150 0.3025 Cy 0.3146 0.3354 0.3529 0.3321 Cx 0.3025 0.3150 0.3150 0.3025 Cy 0.2971 0.3179 0.3354 0.3146 Cx 0.3150 0.3275 0.3275 0.3150 Cy 0.3354 0.3561 0.3736 0.3529 Cx 0.3150 0.3275 0.3275 0.3150 0.3179 0.3386 0.3561 0.3354 Cy X Bin E1 E2 E3 E4 Cx 0.3275 0.3400 0.3400 0.3275 Cy 0.3561 0.3768 0.3943 0.3736 Cx 0.3275 0.3400 0.3400 0.3275 Cy 0.3386 0.3593 0.3768 0.3561 Cx 0.3400 0.3525 0.3525 0.3400 Cy 0.3768 0.3975 0.4150 0.3943 Cx 0.3400 0.3525 0.3525 0.3400 Cy 0.3593 0.3800 0.3975 0.3768 Dominant color coordinate is measured with an accuracy of ± 0.01. 4 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Forward Current Vs Forward Voltage 60 2.5 2 Forward Current, mA Relative Intensity; Relative Normalized Intensity at 30mA Relative Intensity Vs Forward Current 1.5 1 0.5 40 30 20 10 0 0 0 20 40 60 80 2.5 100 3 3.5 4 4.5 Forward Current, mA Forward Voltage, V Maximum Forward Current Vs Temperature Wavelength Vs Forward Current 55 1 Temp. Solder Point, Ts 50 0.9 45 0.8 Relative Intensity Forward Current, mA 50 40 35 30 Temp. Ambient, Ta 25 20 15 0.7 0.6 0.5 0.4 0.3 10 0.2 5 0.1 0 0 0 10 20 30 40 50 60 70 80 400 90 100 110 450 500 550 600 650 700 750 800 Wavelength, nm Temperature Radiation Pattern 30° 20° 10° 0° 1.0 40° 0.8 50° 0.6 60° 0.4 70° 0.2 80° 90° 0 5 08/01/2006 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Power DomiLED • InGaN White : DWW-UJG Package Outlines TM 6 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Recommended Solder Pad 7 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Taping and orientation • Reels come in quantity of 2000 units. • Reel diameter is 180 mm. 8 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Packaging Specification 9 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Packaging Specification Moisture sensitivity level Barcode label DOMINANT Semiconductors ROHS Compliant LOT NO : lotno PB Free PART NO : partno QTY : qty S/N : xxx D/C: xxxx GROUP : group Reel Moisture absorbent material + Moisture indicator The reel, moisture absorbent material and moisture indicator are sealed inside the moisture proof foil bag Average 1pc Power DomiLED 1 completed bag (2000pcs) 0.034 0.034 190 ± 10 190 10 Weight Weight(gram) (gram) Cardboard Box DOMINANT TM Semiconductors For Power DomiLED Cardboard Box Size TM Dimensions (mm) Empty Box Weight (kg) Reel / Box Quantity / Box (pcs) Small 300 x 250 x 250 0.58 15 reels MAX 30,000 MAX Large 416 x 516 x 476 1.74 55 reels MAX 110,000 MAX 10 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Recommended Sn-Pb IR-Reflow Soldering Profile Classification Reflow Profile (JEDEC J-STD-020C) 275 235-240˚C 10-30s 250 225 Ramp-up 3˚C/sec max. Temperature (˚C) 200 175 183˚C 150 60-150s 125 Rampdown 6˚C/sec max. 100 75 Preheat 60-120s 50 360s max 25 0 50 100 150 200 Recommended Pb-free Soldering Profile Classification Reflow Profile (JEDEC J-STD-020C) 300 255-260˚C 10-30s 275 250 Temperature (˚C) Ramp-up 3˚C/sec max. 217˚C 225 200 60-150s 175 150 125 Rampdown 6˚C/sec max. 100 75 Preheat 60-180s 50 25 480s max 0 50 100 150 200 Time (sec) 11 08/01/2007 V(O) DOMINANT TM InGaN White : DWW-UJG Semiconductors Innovating Illumination Revision History Page Subjects Date of Modification - Initial Release 08 Jan 2007 NOTE All the information contained in this document is considered to be reliable at the time of publishing. However, DOMINANT Semiconductors does not assume any liability arising out of the application or use of any product described herein. DOMINANT Semiconductors reserves the right to make changes at any time without prior notice to any products in order to improve reliability, function or design. DOMINANT Semiconductors products are not authorized for use as critical components in life support devices or systems without the express written approval from the Managing Director of DOMINANT Semiconductors. 12 08/01/2007 V(O) DOMINANT TM Semiconductors Innovating Illumination InGaN White : DWW-UJG About Us DOMINANT Semiconductors is a dynamic Malaysian Corporation that is among the world’s leading SMT LED Manufacturers. An excellence – driven organization, it offers a comprehensive product range for diverse industries and applications. Featuring an internationally certified quality assurance acclaim, DOMINANT’s extra bright LEDs are perfectly suited for various lighting applications in the automotive, consumer and communications as well as industrial sectors. With extensive industry experience and relentless pursuit of innovation, DOMINANT’s state-of-art manufacturing, research and testing capabilities have become a trusted and reliable brand across the globe. More information about DOMINANT Semiconductors can be found on the Internet at http://www.dominant-semi.com. Please contact us for more information: Head Quarter DOMINANT Semiconductors Sdn. Bhd. Lot 6, Batu Berendam, FTZ Phase III, 75350 Melaka, Malaysia Tel: (606) 283 3566 Fax: (606) 283 0566 E-mail: [email protected] DOMINANT China Sales Office DOMINANT Semiconductors (Shenzhen) Co. Ltd. 24BC Newbaohui Building, No. 1007 West Nanhai Blvd., Nanshan, Shenzhen, China P.C. 518054 Tel: +86 (755) 86031785 / +86 (755) 86031786 Fax: +86 (755) 86031789 E-mail: [email protected] DOMINANT Korea Sales Office DOMINANT Semiconductors Korea Inc. 902 Sunil Technopia, 440 Sangdaewon-dong, Jungwon-gu, Sungnam-si, Kyunggi-do, Korea 462726 Tel: 82-31-777-3978 Fax: 82-31-777-3976 E-mail: [email protected] DOMINANT Semiconductors Innovating Illumination TM