EVERLIGHT 11-21SYGC/S530

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
1206 Package Chip LED with Inner lens
11-21SYGC/S530-XX/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS complaint version
Descriptions
․The 11-21 SMD Taping is much smaller than lead frame type
components, thus enable smaller board size, higher
packing density, reduced storage space and finally
smaller equipment to be obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Part No.
11-21SYGC/S530-XX/TR8
Chip
Material
Emitted Color
AlGaInP
Brilliant Yellow Green
Lens Color
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 1 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Package Outline Dimensions
-
+
Notes: The tolerances unless mentioned are ±0.1, unit=mm.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 2 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Electrostatic Discharge
ESD
2000
V
Power Dissipation
Pd
60
mW
IFP
60
mA
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering : 260 ℃ for 10 sec.
Soldering Temperature
Tsol
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Luminous Intensity
Iv
*Chip
Rank
Min.
Typ.
Max.
E1
19
29
-----
E2
29
39
-----
E3
39
52
-----
E4
52
62
-----
E5
63
100
-----
Unit
Conditio
n
mcd
Viewing Angle
2θ1/2
-----
-----
60
-----
deg
Peak Wavelength
Dominant
Wavelength
Spectrum Radiation
Bandwidth
λp
-----
-----
575
-----
nm
λd
-----
-----
573
-----
nm
△λ
-----
-----
20
-----
nm
Forward Voltage
VF
-----
1.7
2.0
2.4
V
Reverse Current
IR
-----
-----
-----
10
μA
IF=20mA
VR=5V
*11-21SYGC/S530-XX/TR8
Chip Rank
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 3 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 4 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
xxxxxx
xxxxxx
REF: Forward Voltage Rank
RoHS
xxxxxxxxxxxx
xxxx
xxxxxxxx
Reel Dimensions
Note: The tolerances unless mentioned are ±0.1, Unit = mm.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 5 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: The tolerances unless mentioned are ±0.1, Unit = mm.
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Desiccant
Label
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 6 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level : 90 %
LTPD : 10 %
Test
Sample
No.
Items
Test Condition
Hours/Cycles
Size
Temp. : 260℃±5℃
1
Reflow Soldering
22 PCS.
6 Min.
Min. 5sec.
2
3
4
5
Ac/Re
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
High Temperature
Storage
Low Temperature
Storage
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 7 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.(To fit the MSL-2 .)
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 8 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
11-21SYGC/S530-XX/TR8
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev. 1
Page: 9 of 9
Device No:SZDSE-111-006
Prepared date: 11-Jul-2005
Prepared by: Wu xiaowei