EVERLIGHT 19-21UBC/C430/TR8

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
0603 Package Chip LED (0.8 mm Height)
19-21UBC/C430/TR8
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within ROHS complaint version.
Descriptions
․The 19-21 SMD LED is much smaller than lead
frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Part No.
19-21UBC/C430/TR8
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
Chip
Material
Emitted Color
GaN/SiC
Blue
http://www.everlight.com
Prepared date: 20-Aug-2005
Lens Color
Water Clear
Rev1
Page: 1 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Package Outline Dimensions
-
+
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Page: 2 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
30
mA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40~ +90
℃
Electrostatic Discharge(HBM)
ESD
1000
V
Power Dissipation
Pd
130
mW
IFP
70
mA
Peak Forward Current
(Duty 1/10 @1KHz)
Soldering Temperature
Tsol
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
14.0
18.0
----
mcd
Viewing Angle
2θ1/2
-----
100
-----
deg
Peak Wavelength
λp
-----
466
-----
nm
Dominant Wavelength
λd
-----
428
-----
nm
Spectrum Radiation
Bandwidth
△λ
-----
65
-----
nm
Forward Voltage
VF
-----
3.8
4.5
V
Reverse Current
IR
-----
-----
50
μA
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Condition
IF=20mA
VR=5V
Page: 3 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Page: 4 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
xxxxxx
xxxxxx
REF: Forward Voltage Rank
RoHS
xxxxxxxxxxxx
xxxx
xxxxxxxx
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Page: 5 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label
Aluminum moistue-proof bag
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Desiccant
Rev1
Label
Page: 6 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Test
Sample
Hours/Cycles
Size
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec.
6 Min.
22 PCS.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles
22 PCS.
0/1
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles
22 PCS.
0/1
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
2
3
4
5
High Temperature
Storage
Low Temperature
Storage
Ac/Re
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Rev1
Page: 7 of 9
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Page: 8 of 9
Prepared by: Meng Yali
EVERLIGHT ELECTRONICS CO.,LTD.
19-21UBC/C430/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and
do soldering of each terminal. Be careful because the damage of the product is often started at the time
of the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,
a double-head soldering iron should be used (as below figure). It should be confirmed beforehand
whether the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Everlight Electronics Co., Ltd.
Device No:SZDSE-191-020
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
http://www.everlight.com
Prepared date: 20-Aug-2005
Rev1
Page: 9 of 9
Prepared by: Meng Yali