Technical Data Sheet Silicon PIN Photodiode PD15-22C Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․PD15-22C is a high speed and high sensitive PIN photodiode in miniature flat top view lens SMD package and it is molded in a water clear plastic. The device is Spectrally matched to visible and infrared emitting diode. Applications ․High speed photo detector ․Copier ․Game machine Device Selection Guide LED Part No. Chip Material Lens Color PD Silicon Water clear Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 1 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Package Dimensions 1.1 0.45 0.9 2.3 0.9 2.1 2.0 3.3 2.3 2.8 1.4 1.15 1.65 4-R0.25 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Reverse Voltage VR 32 Units mA Operating Temperature Topr -25 ~ +85 ℃ Storage Temperature Tstg -40 ~ +85 ℃ Soldering Temperature Tsol 260 ℃ Power Dissipation at(or below) 25℃Free Air Temperature Pc 150 mW Notes: *1:Soldering time≦5 seconds. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 2 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth λ0.5 --- 400 --- 1100 nm Wavelength Of Peak Sensitivity λP --- --- 940 --- nm Open-Circuit Voltage VOC Ee=5mW /cm2 λP=940nm --- 0.41 --- V ISC Ee=1mW /cm2 λP=875nm --- 6.5 --- μA Reverse Light Current IL Ee=1mW /cm2 λP=875nm VR=5V 4.2 6.5 --- μA Dark Reverse Current ID Ee=0mW /cm2 VR=10V --- --- 10 nA BVR Ee=0mW /cm2 IR=100μA 32 170 --- V Total Capacitance Ct Ee=0mW /cm2 f=1MHz VR=5V --- 6 --- pF Rise Time tr --- 10 --- Fall Time tf --- 10 --- Short-Circuit Current Reverse Breakdown Voltage VR=5V RL=1000Ω nS Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 3 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Typical Electro-Optical Characteristics Curves Fig.1 Power Dissipation vs. Ambient Temperature 200 Fig.2 Spectral Sensitivity 1.0 Ta=25 C 0.8 150 0.6 100 0.4 50 0.2 0 -25 25 0 50 75 85 100 Fig.3 Dark Current vs. Ambient Temperature 1000 0 100 300 500 700 900 1100 1300 Fig.4 Reverse Light Current vs. Ee 20 100 15 10 10 VR=10V 5 VR=5V 1 20 40 60 80 100 0 0.5 1.0 1.5 3.0 2 Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 4 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Reverse Voltage t 10 f=1MHZ VR=5V Fig.6 Response Time vs. Load Resistance 10 1 VR=10V Ta=25°C 2 0 8 10 6 10 4 10 2 10 -1 -2 -3 0.1 1 10 100 10 1 2 10 3 10 10 4 Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang 5 10 Page: 5 of 9 PD15-22C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 6 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 7 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% NO. Item Test Conditions Test Hours/ Sample Cycles Sizes 1 REFLOW Soldering TEMP.：260℃±5℃ 6Mins 5secs 15mins 50Cycles 2 Temperature Cycle H : +100℃ 5mins L : -40℃ 15mins 3 Thermal Shock H :+100℃ 5mins 50Cycles 10secs 5mins L :-10℃ Failure Judgement Criteria 22pcs Ac/Re 0/1 IL≦L×0.8 22pcs 0/1 L：Lower 22pcs Specification Limit 0/1 4 High Temperature Storage TEMP.：+100℃ 1000hrs 22pcs 0/1 5 Low Temperature Storage TEMP.：-40℃ 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 6 DC Operating Life VR=5V 7 High Temperature/ 85℃ / 85% R.H High Humidity Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 8 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang PD15-22C Packing Quantity Specification 1.1000PCS/1Bag，20Bags/1Box 2.10Boxes/1Carton Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place RoHS PD15-22C Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com Everlight Electronics Co., Ltd. http:\\www.everlight.com Rev 3 Page: 9 of 9 Device No：DPD-152-013 Prepared date：07-20-2005 Prepared by：David Huang