EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Full Color Chip LEDs 15-23B/R6G6BHC-A01/2T Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Full-color type. Descriptions ․The 15-23B SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type Material Emitted Color R6 AlGaInP Brilliant Red G6 InGaN Brilliant Yellow Green BH InGaN Blue Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 1 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Package Outline Dimensions Notes: Tolerances Unless Dimension ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 2 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V R6:25 Forward Current IF G6:25 mA BH:25 Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol 260 (for 5 seconds) ℃ R6:2000 Electrostatic Discharge ESD G6:150 V BH:150 R6:60 Power Dissipation Pd G6:110 mW BH:110 Peak Forward Current (Duty 1/10 @1KHz) R6:60 IF P G6:100 mA BH:100 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 3 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Electro-Optical Characteristics (Ta=25℃) Parameter Luminous Intensity Symbol Min. Typ. Max. Unit R6 72 28.5 28.5 100 50 50 180 90 90 mcd ----- 120 ----- deg ----- 632 575 468 ----- nm ----- 629 575 480 nm ----- nm Iv G6 BH 2θ1/2 Viewing Angle R6 Peak Wavelength λp G6 BH R6 Dominant Wavelength λd G6 BH 619 568 465 Forward Voltage △λ G6 VF ----- 20 BH 25 R6 2.0 2.0 3.5 2.4 2.4 3.9 V ----- 10 10 50 μA ----- G6 BH R6 Reverse Current IR IF=20mA 20 R6 Spectrum Radiation Bandwidth Condition G6 ----- BH VR=5V Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 4 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 5 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves G6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 6 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Typical Electro-Optical Characteristics Curves BH Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 7 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 8 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 9 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 240℃±5℃ 5sec. 2 3 4 5 Test Sample Ac/Re Hours/Cycles Size 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 High Temperature Storage Low Temperature Storage 6 Min. 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/R.H85% 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 10 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Lead solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 11 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai EVERLIGHT ELECTRONICS CO.,LTD. 15-23B/R6G6BHC-A01/2T 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936 Reliability Test AndYang Conditions Office: No 25, Lane 76,Items Sec 3, Chung Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306 Taipei Taiwan, R.O.C http://www.everlight.com The Tucheng, reliability of236, products shall be satisfied with items listed below. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1.0 Page: 12 of 12 Device No:DSE-153- Prepared date: 09-08-2003 Prepared by: Jeff Tsai