EXAR XR16V554IL

XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
MAY 2007
REV. 1.0.1
GENERAL DESCRIPTION
FEATURES
• Pin-to-pin compatible with ST16C454, ST16C554,
The XR16V554 (V554) is a quad Universal
Asynchronous Receiver and Transmitter (UART) with
16 bytes of transmit and receive FIFOs, selectable
receive FIFO trigger levels and data rates of up to 4
Mbps at 3.3 V. Each UART has a set of registers that
provide the user with operating status and control,
receiver error indications, and modem serial interface
controls. An internal loopback capability allows
onboard diagnostics. The V554 is available in a 48pin QFN, 64-pin LQFP, 68-pin PLCC and 80-pin
LQFP packages. The 64-pin and 80-pin packages
only offer the 16 mode interface, but the 48- and 68pin packages offer an additional 68 mode interface
which allows easy integration with Motorola
processors. The XR16V554IV (64-pin) offers three
state interrupt output while the XR16V554DIV
provides continuous interrupt output. The XR16V554
is compatible with the industry standard ST16C554.
TI’s TL16C554A and Philip’s SC16C554B
• Intel or Motorola Data Bus Interface select
• Four independent UART channels
■
Register Set Compatible to 16C550
■
Data rates of up to 4 Mbps at 3.3 V and 3.125
Mbps at 2.5 V
■
16 byte Transmit FIFO
■
16 byte Receive FIFO with error tags
■
4 Selectable RX FIFO Trigger Levels
■
Full modem interface
• 2.25V to 3.6V supply operation
• Crystal oscillator or external clock input
APPLICATIONS
• Portable Appliances
• Telecommunication Network Routers
• Ethernet Network Routers
• Cellular Data Devices
• Factory Automation and Process Controls
FIGURE 1. XR16V554 BLOCK DIAGRAM
* 5 Volt Tolerant Inputs
( Except XTAL1 input)
A2:A0
D7:D0
CSA#
UART Channel A
UART 16 Byte TX FIFO
Regs
TX & RX
CSB#
BRG
IOR#
IOW#
CSC#
CSD#
INTA
2.25V to 3.6 V VCC
GND
TXA, RXA, DTRA#,
DSRA#, RTSA#, CTSA#,
CDA#, RIA#
16 Byte RX FIFO
UART Channel B
(same as Channel A)
TXB, RXB, DTRB#,
DSRB#, RTSB#, CTSB#,
CDB#, RIB#
UART Channel C
(same as Channel A)
TXC, RXC, DTRC#,
DSRC#, RTSC#, CTSC#,
CDC#, RIC#
Reset
UART Channel D
(same as Channel A)
TXD, RXD, DTRD#,
DSRD#, RTSD#, CTSD#,
CDD#, RID#
16/ 68#
INTSEL
Crystal Osc / Buffer
INTB
INTC
INTD
Data Bus
Interface
TXRDY# A-D
RXRDY# A-D
XTAL1
XTAL2
554BLK
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
10
60
DSRD#
CTSA#
11
59
CTSD#
DTRA#
12
58
DTRD#
VCC
13
57
GND
RTSA#
14
56
RTSD#
INTA
15
55
INTD
CSA#
16
TXA
17
IOW#
18
TXB
19
CSB#
CSC#
A3
RID#
CDD#
50
49
RXD
RID#
CDD#
63
41
42
43
RXC
RIC#
CDC#
46
DTRD#
4
45
GND
RTSA#
5
44
RTSD#
INTA
6
43
INTD
CSA#
7
42
CSD#
TXA
8
IOW#
9
XR16V554/554D
64-pin TQFP
Intel Mode Only
41
TXD
40
IOR#
TXC
2
30
31
32
CDC#
DSRC#
CTSC#
RIC#
33
29
16
RXC
CTSB#
28
DTRC#
GND
34
26
15
27
VCC
DTRB#
XTAL2
RTSC#
35
RESET
36
14
25
13
GND
XTAL1
RTSB#
23
INTC
24
37
A0
12
A1
CSC#
INTB
21
38
22
39
11
A2
10
VCC
TXB
CSB#
20
62
40
GND
3
VCC
19
VCC
39
TXRDY#
DTRA#
RIB#
63
38
RXRDY#
CTSD#
RXB
64
37
RESET
DSRD#
47
17
D0
36
XTAL2
48
2
18
GND
35
XTAL1
1
CTSA#
CDB#
65
D1
RXD
51
DSRA#
DSRB#
66
D2
67
VCC
52
34
16/68#
D0
53
VCC
D2
D1
54
56
55
D4
D3
57
RXB
27
CDB#
43
CDC#
RXA
GND
42
RIC#
61
41
62
40
RXC
RIA#
GND
CDA#
64
63
39
TXRDY#
A0
DSRC#
DSRC#
33
44
44
A1
26
26
32
DSRB#
DSRB#
A2
CTSC#
31
DTRC#
45
30
46
25
45
29
24
CTSB#
46
25
D5
DTRB#
24
CTSB#
58
DTRC#
CTSC#
DTRB#
D7
VCC
D6
47
VCC
60
23
47
59
RTSC#
GND
23
38
N.C.
48
GND
RXRDY#
A4
49
RTSC#
37
50
22
INTC
48
RESET
TXC
20
21
49
22
36
51
N.C.
21
XTAL2
XR16V554
68-pin PLCC
Motorola Mode
(16/68# pin connected to GND)
RTSB#
INTB
RTSB#
35
D3
N.C.
50
XTAL1
68
TXD
52
20
34
D4
N.C.
53
19
A0
1
54
TXB
33
D5
N.C.
TXC
A1
2
RTSD#
55
51
32
D6
56
15
18
A2
3
14
IRQ#
R/W#
31
D7
RTSA#
IOR#
16/68#
4
GND
52
30
GND
DTRD#
57
17
29
5
58
13
16
RXB
RXA
12
VCC
TXA
VCC
6
DTRA#
CS#
28
RIA#
CTSD#
CSD#
27
7
DSRD#
59
TXD
RIB#
CDA#
60
11
53
CDB#
8
10
CTSA#
54
XR16V554
68-pin PLCC
Intel Mode
(16/68# pin connected to VCC)
9
DSRA#
28
CDD#
DSRA#
RIB#
RID#
67
63
D1
68
RXD
D2
1
62
D3
2
VCC
D4
3
63
D5
4
64
D6
5
D0
D7
6
INTSEL
GND
7
65
RXA
8
66
CDA#
RIA#
9
FIGURE 2. PIN OUT ASSIGNMENT FOR 68-PIN PLCC PACKAGES IN 16 AND 68 MODE AND 64-PIN LQFP PACKAGES
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
1
36
RXD
VCC
2
35
CTSD#
RTSA#
3
34
GND
INTA
4
33
CSA#
5
32
TXA
6
IOW#
7
TXB
8
CSB#
XR16V554
48-pin QFN
Intel Mode
(16/68# pin connected to VCC)
37 VCC
38 INTSEL
40 D1
39 D0
D3
41 D2
43 D4
42
44 D5
46 D7
45 D6
RXA
48
CTSA#
47 GND
37 VCC
38 INTSEL
40 D1
39 D0
D3
41 D2
43 D4
42
44 D5
46 D7
45 D6
RXA
48
47 GND
FIGURE 3. PIN OUT ASSIGNMENT FOR 48-PIN QFN PACKAGE AND 80-PIN LQFP PACKAGE
CTSA#
1
36
RXD
VCC
2
35
CTSD#
RTSA#
3
34
GND
RTSD#
INTA
4
33
RTSD#
INTD
CSA#
5
32
INTD
31 CSD#
TXA
6
XR16V554
48-pin QFN
Motorola Mode
(16/68# pin connected to GND)
31 CSD#
27
CSC#
RTSB#
11
26
INTC
RTSB#
11
26
INTC
CTSB#
12
25
RTSC#
CTSB#
12
25
RTSC#
TXD
9
TXA
10
IOW#
11
TXB
CSB#
N.C.
N.C.
62
61
XTAL2
RID#
CDD#
RXD
65
63
VCC
66
64
INTSEL
67
RXB
D1
D0
68
D2
69
70
73
D4
74
D3
D5
75
71
GND
76
72
RXA
77
RESET
RIA#
78
XTAL2
CDA#
79
XTAL1
N.C.
80
20
CSD#
52
XR16V554
80-pin LQFP
Intel Mode Only
RESET
8
CSA#
19
INTD
53
14
54
13
7
INTA
16/68#
RTSA#
23
RTSD#
24
6
55
VCC
GND
VCC
CTSC#
56
D6
5
D7
DTRD#
DTRA#
22
CTSD#
57
RXC
58
4
GND
3
CTSA#
20
DSRA#
19
17
A1
A0
2
DSRD#
18
15
16
N.C.
59
16/68#
60
14
1
NC
13
NC
RXB
A2
23
10
24
INTB
VCC
CSC#
CTSC#
27
21
10
22
TXC
INTB
RXC
28
GND
9
18
CSB#
17
TXC
A0
28
XTAL1
9
15
8
16
7
TXB
A1
IOW#
IOR#
A2
TXD
29
21
30
51
IOR#
50
TXC
12
49
CSC#
13
48
INTC
INTB
14
47
RTSC#
RTSB#
15
46
VCC
GND
16
45
DTRC#
DTRB#
17
44
CTSC#
3
39
40
CDC#
N.C.
36
GND
38
35
TXRDY#
37
34
RXRDY#
RXC
33
RIC#
32
XTAL2
RESET
31
29
A1
XTAL1
28
A2
30
27
N.C.
A0
26
N.C.
N.C.
25
41
24
20
RXB
NC
RIB#
N.C.
23
42
CDB#
19
22
DSRC#
N.C.
43
21
18
N.C.
CTSB#
DSRB#
30
TXD
29
IOR#
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
ORDERING INFORMATION
PART NUMBER
PACKAGE
OPERATING TEMPERATURE
RANGE
DEVICE STATUS
XR16V554IJ
68-Lead PLCC
-40°C to +85°C
Active
XR16V554IV
64-Lead LQFP
-40°C to +85°C
Active
XR16V554DIV
64-Lead LQFP
-40°C to +85°C
Active
XR16V554IL
48-pin QFN
-40°C to +85°C
Active
XR16V554IV80
80-Lead LQFP
-40°C to +85°C
Active
PIN DESCRIPTIONS
Pin Description
NAME
48-QFN
PIN #
64-LQFP 68-PLCC 80-LQFP
TYPE
PIN #
PIN#
PIN #
DESCRIPTION
DATA BUS INTERFACE
A2
A1
A0
15
16
17
22
23
24
32
33
34
28
29
30
I
D7
D6
D5
D4
D3
D2
D1
D0
46
45
44
43
42
41
40
39
60
59
58
57
56
55
54
53
5
4
3
2
1
68
67
66
75
74
73
72
71
70
69
68
I/O
IOR#
(VCC)
29
40
52
51
I
When 16/68# pin is HIGH, the Intel bus interface is
selected and this input becomes read strobe (active
low). The falling edge instigates an internal read cycle
and retrieves the data byte from an internal register
pointed by the address lines [A2:A0], puts the data byte
on the data bus to allow the host processor to read it on
the rising edge.
When 16/68# pin is LOW, the Motorola bus interface is
selected and this input is not used and should be connected to VCC.
IOW#
(R/W#)
7
9
18
11
I
When 16/68# pin is HIGH, it selects Intel bus interface
and this input becomes write strobe (active low). The
falling edge instigates the internal write cycle and the
rising edge transfers the data byte on the data bus to
an internal register pointed by the address lines.
When 16/68# pin is LOW, the Motorola bus interface is
selected and this input becomes read (HIGH) and write
(LOW) signal.
CSA#
(CS#)
5
7
16
9
I
When 16/68# pin is HIGH, this input is chip select A
(active low) to enable channel A in the device.
When 16/68# pin is LOW, this input becomes the chip
select (active low) for the Motorola bus interface.
4
Address data lines [2:0]. These 3 address lines select
one of the internal registers in UART channel A-D during a data bus transaction.
Data bus lines [7:0] (bidirectional).
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
Pin Description
NAME
48-QFN
PIN #
64-LQFP 68-PLCC 80-LQFP
TYPE
PIN #
PIN#
PIN #
DESCRIPTION
CSB#
(A3)
9
11
20
13
I
When 16/68# pin is HIGH, this input is chip select B
(active low) to enable channel B in the device.
When 16/68# pin is LOW, this input becomes address
line A3 which is used for channel selection in the Motorola bus interface.
CSC#
(A4)
27
38
50
49
I
When 16/68# pin is HIGH, this input is chip select C
(active low) to enable channel C in the device.
When 16/68# pin is LOW, this input becomes address
line A4 which is used for channel selection in the Motorola bus interface.
CSD#
(VCC)
31
42
54
53
I
When 16/68# pin is HIGH, this input is chip select D
(active low) to enable channel D in the device.
When 16/68# pin is LOW, this input is not used and
should be connected VCC.
INTA
(IRQ#)
4
6
15
8
INTB
INTC
INTD
(N.C.)
10
26
32
12
37
43
21
49
55
14
48
54
O
When 16/68# pin is HIGH for Intel bus interface, these
ouputs become the interrupt outputs for channels B, C,
and D. The output state is defined by the user through
the software setting of MCR[3]. The interrupt outputs
are set to the active mode when MCR[3] is set to a logic
1 and are set to the three state mode when MCR[3] is
set to a logic 0 (default). See MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
these outputs are unused and will stay at logic zero
level. Leave these outputs unconnected.
TXRDY#
-
-
39
35
O
Transmitter Ready (active low). This output is a logically ANDed status of TXRDY# A-D. See Table 5. If this
output is unused, leave it unconnected.
RXRDY#
-
-
38
34
O
Receiver Ready (active low). This output is a logically
ANDed status of RXRDY# A-D. See Table 5. If this output is unused, leave it unconnected.
O
When 16/68# pin is HIGH for Intel bus interface, this
(OD) ouput becomes channel A interrupt output. The output
state is defined by the user and through the software
setting of MCR[3]. INTA is set to the active mode when
MCR[3] is set to a logic 1. INTA is set to the three state
mode when MCR[3] is set to a logic 0 (default). See
MCR[3].
When 16/68# pin is LOW for Motorola bus interface,
this output becomes device interrupt output (active low,
open drain). An external pull-up resistor is required for
proper operation.
5
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
Pin Description
NAME
48-QFN
PIN #
INTSEL
38
64-LQFP 68-PLCC 80-LQFP
TYPE
PIN #
PIN#
PIN #
-
DESCRIPTION
65
67
I
Interrupt Select (active high, input with internal pulldown).
When 16/68# pin is HIGH for Intel bus interface, this pin
can be used in conjunction with MCR bit-3 to enable or
disable the INT A-D pins or override MCR bit-3 and
enable the interrupt outputs. Interrupt outputs are
enabled continuously when this pin is HIGH. MCR bit-3
enables and disables the interrupt output pins. In this
mode, MCR bit-3 is set to a logic 1 to enable the continuous output. See MCR bit-3 description for full detail.
This pin must be LOW in the Motorola bus interface
mode. For the 64 pin packages, this pin is bonded to
VCC internally in the XR16V554D so the INT outputs
operate in the continuous interrupt mode. This pin is
bonded to GND internally in the XR16V554 and therefore requires setting MCR bit-3 for enabling the interrupt output pins.
MODEM OR SERIAL I/O INTERFACE
TXA
TXB
TXC
TXD
6
8
28
30
8
10
39
41
17
19
51
53
10
12
50
52
O
UART channels A-D Transmit Data and infrared transmit data. In this mode, the TX signal will be HIGH during reset, or idle (no data).
RXA
RXB
RXC
RXD
48
13
22
36
62
20
29
51
7
29
41
63
77
25
37
65
I
UART channel A-D Receive Data. Normal receive data
input must idle HIGH.
RTSA#
RTSB#
RTSC#
RTSD#
3
11
25
33
5
13
36
44
14
22
48
56
7
15
47
55
O
UART channels A-D Request-to-Send (active low) or
general purpose output. If these outputs are not used,
leave them unconnected.
CTSA#
CTSB#
CTSC#
CTSD#
1
12
23
35
2
16
33
47
11
25
45
59
4
18
44
58
I
UART channels A-D Clear-to-Send (active low) or general purpose input. These inputs should be connected
to VCC when not used.
DTRA#
DTRB#
DTRC#
DTRD#
-
3
15
34
46
12
24
46
58
5
17
45
57
O
UART channels A-D Data-Terminal-Ready (active low)
or general purpose output. If these outputs are not
used, leave them unconnected.
DSRA#
DSRB#
DSRC#
DSRD#
-
1
17
32
48
10
26
44
60
3
19
43
59
I
UART channels A-D Data-Set-Ready (active low) or
general purpose input. This input should be connected
to VCC when not used. This input has no effect on the
UART.
6
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
Pin Description
NAME
48-QFN
PIN #
64-LQFP 68-PLCC 80-LQFP
TYPE
PIN #
PIN#
PIN #
CDA#
CDB#
CDC#
CDD#
-
64
18
31
49
9
27
43
61
79
23
39
63
I
UART channels A-D Carrier-Detect (active low) or general purpose input. This input should be connected to
VCC when not used. This input has no effect on the
UART.
RIA#
RIB#
RIC#
RID#
-
63
19
30
50
8
28
42
62
78
24
38
64
I
UART channels A-D Ring-Indicator (active low) or general purpose input. This input should be connected to
VCC when not used. This input has no effect on the
UART.
DESCRIPTION
ANCILLARY SIGNALS
XTAL1
18
25
35
31
I
Crystal or external clock input. Caution: this input is not
5V tolerant.
XTAL2
19
26
36
32
O
Crystal or buffered clock output.
16/68#
14
-
31
-
I
Intel or Motorola Bus Select (input with internal pull-up).
When 16/68# pin is HIGH, 16 or Intel Mode, the device
will operate in the Intel bus type of interface.
When 16/68# pin is LOW, 68 or Motorola mode, the
device will operate in the Motorola bus type of interface.
Motorola bus interface is not available on the 64 pin
package.
RESET
(RESET#)
20
27
37
33
I
When 16/68# pin is HIGH for Intel bus interface, this
input becomes the Reset pin (active high). In this case,
a 40 ns minimum HIGH pulse on this pin will reset the
internal registers and all outputs. The UART transmitter
output will be held HIGH, the receiver input will be
ignored and outputs are reset during reset period
(Table 13). When 16/68# pin is at LOW for Motorola
bus interface, this input becomes Reset# pin (active
low). This pin functions similarly, but instead of a HIGH
pulse, a 40 ns minimum LOW pulse will reset the internal registers and outputs.
Motorola bus interface is not available on the 64 pin
package.
13, 30,
47, 64
6, 30, 46,
66
Pwr
2.25V to 3.6V power supply. All inputs, except XTAL1,
are 5V tolerant.
VCC
2, 24, 37 4, 21, 35,
52
GND
21, 47
14, 28,
45, 61
6, 23, 40,
57
16, 36,
56, 76
Pwr
Power supply common, ground.
GND
Center
Pad
N/A
N/A
N/A
Pwr
The center pad on the backside of the QFN package is
metallic and should be connected to GND on the PCB.
The thermal pad size on the PCB should be the approximate size of this center pad and should be solder mask
defined. The solder mask opening should be at least
0.0025" inwards from the edge of the PCB thermal pad.
7
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
Pin Description
NAME
48-QFN
PIN #
N.C.
-
64-LQFP 68-PLCC 80-LQFP
TYPE
PIN #
PIN#
PIN #
-
-
1, 2, 20,
21, 22,
26, 27,
40, 41,
42, 60,
61, 62,
80
DESCRIPTION
No Connection. These pins are not used in either the
Intel or Motorola bus modes.
Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain.
8
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
1.0 PRODUCT DESCRIPTION
The XR16V554 (V554) integrates the functions of 4 enhanced 16C550 Universal Asynchrounous Receiver and
Transmitter (UART). Each UART is independently controlled and has its own set of device configuration
registers. The configuration registers set is 16550 UART compatible for control, status and data transfer.
Additionally, each UART channel has 16 bytes of transmit and receive FIFOs, programmable baud rate
generator and data rate up to 4 Mbps at 3.3 V. The XR16V554 can operate from 2.25 to 3.6 volts. The V554 is
fabricated with an advanced CMOS process.
Enhanced FIFO
The V554 QUART provides a solution that supports 16 bytes of transmit and receive FIFO memory, instead of
one byte in the ST16C454. The V554 is designed to work with high performance data communication systems,
that require fast data processing time. Increased performance is realized in the V554 by the larger transmit and
receive FIFOs and Receiver FIFO trigger level control. This allows the external processor to handle more
networking tasks within a given time. This increases the service interval giving the external CPU additional time
for other applications and reducing the overall UART interrupt servicing time.
Data Bus Interface, Intel or Motorola Type
The V554 provides a single host interface for the 4 UARTs and supports Intel or Motorola microprocessor
(CPU) data bus interface. The Intel bus compatible interface allows direct interconnect to Intel compatible type
of CPUs using IOR#, IOW# and CSA#, CSB#, CSC# or CSD# inputs for data bus operation. The Motorola bus
compatible interface instead uses the R/W#, CS#, A3 and A4 signals for data bus transactions. Few data bus
interface signals change their functions depending on user’s selection, see pin description for details. The Intel
and Motorola bus interface selection is made through the pin 16/68#.
Data Rate
The V554 is capable of operation up to 4 Mbps at 3.3V. The device can operate at 3.3V with a crystal oscillator
of up to 24 MHz crystal on pins XTAL1 and XTAL2, or external clock source of 64 MHz on XTAL1 pin. With a
typical crystal of 14.7456 MHz and through a software option, the user can set the sampling rate for data rates
of up to 921.6 Kbps.
Enhanced Features
The rich feature set of the V554 is available through the internal registers. Selectable receive FIFO trigger
levels, programmable baud rates, infrared encoder/decoder interface and modem interface controls are all
standard features. In the 16 mode INTSEL and MCR bit-3 can be configured to provide a software controlled or
continuous interrupt capability. For backward compatibility to the ST16C554, the 64-pin LQFP does not have
the INTSEL pin. Instead, two different LQFP packages are offered. The XR16V554DIV operates in the
continuous interrupt enable mode by internally bonding INTSEL to VCC. The XR16V554IV operates in
conjunction with MCR bit-3 by internally bonding INTSEL to GND.
9
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
2.0 FUNCTIONAL DESCRIPTIONS
2.1
CPU Interface
The CPU interface is 8 data bits wide with 3 address lines and control signals to execute data bus read and
write transactions. The V554 data interface supports the Intel compatible types of CPUs and it is compatible to
the industry standard 16C550 UART. No clock (oscillator nor external clock) is required for a data bus
transaction. Each bus cycle is asynchronous using CS# A-D, IOR# and IOW# or CS#, R/W#, A4 and A3 inputs.
All four UART channels share the same data bus for host operations. A typical data bus interconnection for
Intel and Motorola mode is shown in Figure 4.
FIGURE 4. XR16V554 TYPICAL INTEL/MOTOROLA DATA BUS INTERCONNECTIONS
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
A0
A1
A2
VCC
VCC
TXA
RXA
UART
Channel A
DTRA#
RTSA#
CTSA#
DSRA#
CDA#
Serial Interface of
RS-232
RIA#
IOR#
IOR#
IOW#
IOW#
UART_CSA#
UART_CSB#
UART_CSC#
UART_CSD#
CSA#
CSB#
CSC#
CSD#
UART_INTA
INTA
UART_INTB
INTB
UART_INTC
INTC
UART_INTD
INTD
UART_RESET
UART
Channel B
UART
Channel C
UART
Channel D
Similar
to Ch A
Serial Interface of
RS-232
Similar
to Ch A
Similar
to Ch A
RESET
VCC
GND
16/68#
Intel Data Bus (16 Mode) Interconnections
VCC
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
A0
A1
A2
A0
A1
DSRA#
A2
RIA#
A3
A4
CSB#
CSC#
CSD#
VCC
TXA
RXA
UART
Channel A
DTRA#
RTSA#
CTSA#
Serial Interface of
RS-232
CDA#
UART
Channel B Similar
to Ch A
IOR#
VCC
IOW#
R/W#
UART_CS#
VCC
CSA#
VCC
UART_IRQ#
INTA
INTB
INTC
INTD
RESET#
16/68#
(no connect)
(no connect)
(no connect)
UART_RESET#
UART
Channel C
UART
Channel D
Similar
to Ch A
Similar
to Ch A
GND
Motorola Data Bus (68 Mode) Interconnections
10
Serial Interface of
RS-232
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
2.2
Device Reset
The RESET input resets the internal registers and the serial interface outputs in all channels to their default
state (see Table 13). An active high pulse of longer than 40 ns duration will be required to activate the reset
function in the device. Following a power-on reset or an external reset, the V554 is software compatible with
previous generation of UARTs, 16C454 and 16C554.
2.3
Channel Selection
The UART provides the user with the capability to bi-directionally transfer information between an external
CPU and an external serial communication device. During Intel Bus Mode (16/68# pin is connected to VCC), a
logic 0 on chip select pins, CSA#, CSB#, CSC# or CSD# allows the user to select UART channel A, B, C or D
to configure, send transmit data and/or unload receive data to/from the UART. Selecting all four UARTs can be
useful during power up initialization to write to the same internal registers, but do not attempt to read from all
four uarts simultaneously. Individual channel select functions are shown in Table 1.
TABLE 1: CHANNEL A-D SELECT IN 16 MODE
CSA# CSB# CSC# CSD#
FUNCTION
1
1
1
1
UART de-selected
0
1
1
1
Channel A selected
1
0
1
1
Channel B selected
1
1
0
1
Channel C selected
1
1
1
0
Channel D selected
0
0
0
0
Channels A-D selected
During Motorola Bus Mode (16/68# pin is connected to GND), the package interface pins are configured for
connection with Motorola, and other popular microprocessor bus types. In this mode the V554 decodes two
additional addresses, A3 and A4, to select one of the four UART ports. The A3 and A4 address decode
function is used only when in the Motorola Bus Mode. See Table 2.
TABLE 2: CHANNEL A-D SELECT IN 68 MODE
CS#
A4
A3
FUNCTION
1
X
X
UART de-selected
0
0
0
Channel A selected
0
0
1
Channel B selected
0
1
0
Channel C selected
0
1
1
Channel D selected
11
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
2.4
REV. 1.0.1
Channels A-D Internal Registers
Each UART channel in the V554 has a set of enhanced registers for controlling, monitoring and data loading
and unloading. The configuration register set is compatible to those already available in the standard single
16C550. These registers function as data holding registers (THR/RHR), interrupt status and control registers
(ISR/IER), a FIFO control register (FCR), receive line status and control registers (LSR/LCR), modem status
and control registers (MSR/MCR), programmable data rate (clock) divisor registers (DLL/DLM), and a user
accessible scratchpad register (SPR). All the register functions are discussed in full detail later in “Section 3.0,
UART INTERNAL REGISTERS” on page 19.
2.5
INT Ouputs for Channels A-D
The interrupt outputs change according to the operating mode and enhanced features setup. Table 3 and 4
summarize the operating behavior for the transmitter and receiver. Also see Figure 18 through 23.
TABLE 3: INT PIN OPERATION FOR TRANSMITTER FOR CHANNELS A-D
FCR BIT-0 = 1 (FIFO ENABLED)
FCR BIT-0 = 0
(FIFO DISABLED)
INT Pin
LOW = a byte in THR
HIGH = THR empty
FCR Bit-3 = 0
(DMA Mode Disabled)
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or
FIFO empty
FCR Bit-3 = 1
(DMA Mode Enabled)
LOW = FIFO above trigger level
HIGH = FIFO below trigger level or
FIFO empty
TABLE 4: INT PIN OPERATION FOR RECEIVER FOR CHANNELS A-D
FCR BIT-0 = 0
(FIFO DISABLED)
FCR BIT-0 = 1 (FIFO ENABLED)
FCR Bit-3 = 0
(DMA Mode Disabled)
INT Pin
2.6
LOW = no data
HIGH = 1 byte
LOW = FIFO below trigger level
HIGH = FIFO above trigger level
FCR Bit-3 = 1
(DMA Mode Enabled)
LOW = FIFO below trigger level
HIGH = FIFO above trigger level
DMA Mode
The device does not support direct memory access. The DMA Mode (a legacy term) in this document does not
mean “direct memory access” but refers to data block transfer operation. The DMA mode affects the state of
the RXRDY# A-D and TXRDY# A-D output pins. The transmit and receive FIFO trigger levels provide
additional flexibility to the user for block mode operation. The LSR bits 5-6 provide an indication when the
transmitter is empty or has an empty location(s) for more data. The user can optionally operate the transmit
and receive FIFO in the DMA mode (FCR bit-3 = 1). When the transmit and receive FIFOs are enabled and the
DMA mode is disabled (FCR bit-3 = 0), the V554 is placed in single-character mode for data transmit or receive
operation. When DMA mode is enabled (FCR bit-3 = 1), the user takes advantage of block mode operation by
loading or unloading the FIFO in a block sequence determined by the programmed trigger level. The following
table show their behavior. Also see Figure 18 through 23.
12
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D
PINS
FCR BIT-0=0
(FIFO DISABLED)
FCR BIT-0=1 (FIFO ENABLED)
FCR BIT-3 = 0
(DMA MODE DISABLED)
FCR BIT-3 = 1
(DMA MODE ENABLED)
RXRDY#
LOW = 1 byte
HIGH = no data
LOW = at least 1 byte in FIFO
HIGH = FIFO empty
HIGH to LOW transition when FIFO reaches the
trigger level, or timeout occurs
LOW to HIGH transition when FIFO empties
TXRDY#
LOW = THR empty
HIGH = byte in THR
LOW = FIFO empty
HIGH = at least 1 byte in FIFO
LOW = FIFO has at least 1 empty location
HIGH = FIFO is full
2.7
Crystal Oscillator or External Clock Input
The V554 includes an on-chip oscillator (XTAL1 and XTAL2) to produce a clock for both UART sections in the
device. The CPU data bus does not require this clock for bus operation. The crystal oscillator provides a
system clock to the Baud Rate Generators (BRG) section found in each of the UART. XTAL1 is the input to the
oscillator or external clock buffer input with XTAL2 pin being the output. Caution: the XTAL1 input is not 5V
tolerant. For programming details, see “Section 2.8, Programmable Baud Rate Generator” on page 13.
FIGURE 5. TYPICAL CRYSTAL CONNECTIONS
R=300K to 400K
XTAL1
14.7456
MHz
XTAL2
C2
22-47pF
C1
22-47pF
The on-chip oscillator is designed to use an industry standard microprocessor crystal (parallel resonant,
fundamental frequency with 10-22 pF capacitance load, ESR of 20-120 ohms and 100ppm frequency
tolerance) connected externally between the XTAL1 and XTAL2 pins. Typical oscillator connections are shown
in Figure 5. Alternatively, an external clock can be connected to the XTAL1 pin to clock the internal baud rate
generator for standard or custom rates. For further reading on oscillator circuit please see application note
DAN108 on EXAR’s web site.
2.8
Programmable Baud Rate Generator
Each UART has its own Baud Rate Generator (BRG) for the transmitter and receiver. The BRG further divides
this clock by a programmable divisor between 1 and (216 - 0.0625) in increments of 0.0625 (1/16) to obtain a
16X sampling rate clock of the serial data rate. The sampling rate clock is used by the transmitter for data bit
shifting and receiver for data sampling. The BRG divisor defaults to the maximum baud rate (DLL = 0x01 and
DLM = 0x00) upon power up and reset. Programming the Baud Rate Generator Registers DLL and DLM
provides the capability for selecting the operating data rate. Table 6 shows the standard data rates available
with a 24MHz crystal or external clock at 16X clock rate. If the pre-scaler is used (MCR bit-7 = 1), the output
data rate will be 4 times less than that shown in Table 6.
13
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 6. BAUD RATE GENERATOR
To Other
Channels
DLL and DLM
Registers
XTAL1
XTAL2
Crystal
Osc /
Buffer
Programmable Baud
Rate Generator Logic
16 X Sampling
Rate Clock
to Transmitter
and Receiver
TABLE 6: TYPICAL DATA RATES WITH A 14.7456 MHZ CRYSTAL OR EXTERNAL CLOCK
OUTPUT Data Rate
MCR Bit-7=0
(DEFAULT)
DIVISOR FOR 16x
Clock (Decimal)
DIVISOR FOR 16x
Clock (HEX)
DLM PROGRAM
VALUE (HEX)
DLL PROGRAM
VALUE (HEX)
DATA RATE
ERROR (%)
400
2304
900
09
00
0
2400
384
180
01
80
0
4800
192
C0
00
C0
0
9600
96
60
00
60
0
19.2k
48
30
00
30
0
38.4k
24
18
00
18
0
76.8k
12
0C
00
0C
0
153.6k
6
06
00
06
0
230.4k
4
04
00
04
0
460.8k
2
02
00
02
0
921.6k
1
01
00
01
0
2.9
Transmitter
The transmitter section comprises of an 8-bit Transmit Shift Register (TSR) and 16 bytes of FIFO which
includes a byte-wide Transmit Holding Register (THR). TSR shifts out every data bit with the 16X internal
sampling clock. A bit time is 16X clock periods. The transmitter sends the start-bit followed by the number of
data bits, inserts the proper parity-bit if enabled, and adds the stop-bit(s). The status of the FIFO and TSR are
reported in the Line Status Register (LSR bit-5 and bit-6).
14
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
2.9.1
Transmit Holding Register (THR) - Write Only
The transmit holding register is an 8-bit register providing a data interface to the host processor. The host
writes transmit data byte to the THR to be converted into a serial data stream including start-bit, data bits,
parity-bit and stop-bit(s). The least-significant-bit (Bit-0) becomes first data bit to go out. The THR is the input
register to the transmit FIFO of 16 bytes when FIFO operation is enabled by FCR bit-0. Every time a write
operation is made to the THR, the FIFO data pointer is automatically bumped to the next sequential data
location.
2.9.2
Transmitter Operation in non-FIFO Mode
The host loads transmit data to THR one character at a time. The THR empty flag (LSR bit-5) is set when the
data byte is transferred to TSR. THR flag can generate a transmit empty interrupt (ISR bit-1) when it is enabled
by IER bit-1. The TSR flag (LSR bit-6) is set when TSR becomes completely empty.
FIGURE 7. TRANSMITTER OPERATION IN NON-FIFO MODE
Data
Byte
Transmit
Holding
Register
(THR)
THR Interrupt (ISR bit-1)
Enabled by IER bit-1
16X Clock
M
S
B
Transmit Shift Register (TSR)
L
S
B
TXNOFIFO1
2.9.3
Transmitter Operation in FIFO Mode
The host may fill the transmit FIFO with up to 16 bytes of transmit data. The THR empty flag (LSR bit-5) is set
whenever the FIFO is empty. The THR empty flag can generate a transmit empty interrupt (ISR bit-1) when the
FIFO becomes empty. The transmit empty interrupt is enabled by IER bit-1. The TSR flag (LSR bit-6) is set
when TSR/FIFO becomes empty.
FIGURE 8. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE
Transmit
Data Byte
16X Clock
Transmit
FIFO
THR Interrupt (ISR bit-1)
When it becomes empty.
FIFO is Enabled by FCR
Bit-0=1
Transmit Data Shift Register
( TSR )
TXFIFO1
15
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
2.10
REV. 1.0.1
Receiver
The receiver section contains an 8-bit Receive Shift Register (RSR) and 16 bytes of FIFO which includes a
byte-wide Receive Holding Register (RHR). The RSR uses the 16X clock for timing. It verifies and validates
every bit on the incoming character in the middle of each data bit. On the falling edge of a start or false start bit,
an internal receiver counter starts counting at the 16X clock rate. After 8 clocks the start bit period should be at
the center of the start bit. At this time the start bit is sampled and if it is still LOW it is validated. Evaluating the
start bit in this manner prevents the receiver from assembling a false character. The rest of the data bits and
stop bits are sampled and validated in this same manner to prevent false framing. If there were any error(s),
they are reported in the LSR register bits 2-4. Upon unloading the receive data byte from RHR, the receive
FIFO pointer is bumped and the error tags are immediately updated to reflect the status of the data byte in
RHR register. RHR can generate a receive data ready interrupt upon receiving a character or delay until it
reaches the FIFO trigger level. Furthermore, data delivery to the host is guaranteed by a receive data ready
time-out interrupt when data is not received for 4 word lengths as defined by LCR[1:0] plus 12 bits time. This is
equivalent to 3.7-4.6 character times. The RHR interrupt is enabled by IER bit-0. See Figure 9 and Figure 10
below.
2.10.1
Receive Holding Register (RHR) - Read-Only
The Receive Holding Register is an 8-bit register that holds a receive data byte from the Receive Shift
Register. It provides the receive data interface to the host processor. The RHR register is part of the receive
FIFO of 16 bytes by 11-bit wide, the 3 extra bits are for the 3 error tags to be reported in LSR register. When
the FIFO is enabled by FCR bit-0, the RHR contains the first data character received by the FIFO. After the
RHR is read, the next character byte is loaded into the RHR and the errors associated with the current data
byte are immediately updated in the LSR bits 2-4.
FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE
16X Clock
Receive Data Shift
Register (RSR)
Receive
Data Byte
and Errors
Error
Tags in
LSR bits
4:2
Receive Data
Holding Register
(RHR)
Data Bit
Validation
Receive Data Characters
RHR Interrupt (ISR bit-2)
RXFIFO1
16
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 10. RECEIVER OPERATION IN FIFO
16X C lock
R eceive D ata Shift
R egister (R SR )
D ata Bit
V alidation
16 bytes by 11-bit w ide
FIFO
Error Tags
(16-sets)
D ata falls to
4
R eceive
D ata FIFO
FIFO
Trigger=8
Error Tags in
LSR bits 4:2
D ata fills to
14
R eceive D ata
Byte and Errors
R eceive D ata C haracters
E xam ple
: - R X FIFO trigger level selected at 8 bytes
(See N ote Below )
Asking for sending data w hen data falls below the flow
control trigger level to restart rem ote transm itter.
R H R Interrupt (IS R bit-2) program m ed for
desired FIFO trigger level.
FIFO is Enabled by FC R bit-0=1
Asking for stopping data w hen data fills above the flow
control trigger level to suspend rem ote transm itter.
R eceive
D ata
R XFIFO 1
17
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
2.11
REV. 1.0.1
Internal Loopback
The V554 UART provides an internal loopback capability for system diagnostic purposes. The internal
loopback mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally.
Figure 11 shows how the modem port signals are re-configured. Transmit data from the transmit shift register
output is internally routed to the receive shift register input allowing the system to receive the same data that it
was sending. The TX pin is held HIGH or mark condition while RTS# and DTR# are de-asserted, and CTS#,
DSR# CD# and RI# inputs are ignored. Caution: the RX input must be held HIGH during loopback test else
upon exiting the loopback test the UART may detect and report a false “break” signal.
FIGURE 11. INTERNAL LOOP BACK IN CHANNEL A AND B
VCC
TX A-D
Transmit Shift Register
(THR/FIFO)
Receive Shift Register
(RHR/FIFO)
RX A-D
VCC
RTS# A-D
Modem / General Purpose Control Logic
Internal Data Bus Lines and Control Signals
MCR bit-4=1
RTS#
CTS#
CTS# A-D
VCC
DTR# A-D
DTR#
DSR#
DSR# A-D
OP1#
RI#
OP2#
CD#
RI# A-D
CD# A-D
18
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
3.0 UART INTERNAL REGISTERS
Each UART channel in the V554 has its own set of configuration registers selected by address lines A0, A1
and A2 with a specific channel selected (See Table 1 and Table 2). The complete register set is shown on
Table 7 and Table 8.
TABLE 7: UART CHANNEL A AND B UART INTERNAL REGISTERS
A2,A1,A0 ADDRESSES
REGISTER
READ/WRITE
COMMENTS
16C550 COMPATIBLE REGISTERS
0 0 0
RHR - Receive Holding Register
THR - Transmit Holding Register
Read-only
Write-only
0 0 0
DLL - Divisor LSB
Read/Write
0 0 1
DLM - Divisor MSB
Read/Write
0 0 1
IER - Interrupt Enable Register
Read/Write
0 1 0
ISR - Interrupt Status Register
FCR - FIFO Control Register
Read-only
Write-only
0 1 1
LCR - Line Control Register
Read/Write
1 0 0
MCR - Modem Control Register
Read/Write
1 0 1
LSR - Line Status Register
Read-only
1 1 0
MSR - Modem Status Register
Read-only
1 1 1
SPR - Scratch Pad Register
Read/Write
LCR[7] = 0
LCR[7] = 1, LCR ≠ 0xBF
LCR[7] = 0
LCR[7] = 0
19
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
TABLE 8: INTERNAL REGISTERS DESCRIPTION.
ADDRESS
A2-A0
REG
NAME
READ/
WRITE
BIT-7
BIT-6
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
COMMENT
16C550 Compatible Registers
000
RHR
RD
Bit-7
Bit-6
Bit-5
Bit-4
Bit-3
Bit-2
Bit-1
Bit-0
000
THR
WR
Bit-7
Bit-6
Bit-5
Bit-4
Bit-3
Bit-2
Bit-1
Bit-0
001
IER
RD/WR
0
0
0
0
010
ISR
RD
FIFOs
FIFOs
Enabled Enabled
0
0
INT
Source
Bit-3
INT
INT
INT
Source Source Source
Bit-2
Bit-1
Bit-0
010
FCR
WR
RX FIFO RX FIFO
Trigger Trigger
0
0
DMA
Mode
Enable
TX
FIFO
Reset
011
LCR
RD/WR
Divisor
Enable
Set TX
Break
Set
Parity
Even
Parity
Parity
Enable
Stop
Bits
100
MCR
RD/WR
0
0
0
Internal
Lopback
Enable
INT
Output
Enable
(OP2#)
101
LSR
RD/WR
RX
FIFO
Global
Error
THR &
TSR
Empty
THR
Empty
RX Break
RX
Framing
Error
RX
Parity
Error
RX
Overrun
Error
RX
Data
Ready
Modem RX Line
TX
RX
Stat. Int. Stat.
Empty
Data
Enable
Int.
Int
Int.
Enable Enable Enable
RX
FIFO
Reset
LCR[7] = 0
FIFOs
Enable
Word
Word
Length Length
Bit-1
Bit-0
Rsvd
RTS# DTR#
(OP1#) Output Output
Control Control
110
MSR
RD/WR
CD#
Input
RI# Input
DSR#
Input
CTS#
Input
Delta
CD#
Delta
RI#
Delta
DSR#
Delta
CTS#
111
SPR
RD/WR
Bit-7
Bit-6
Bit-5
Bit-4
Bit-3
Bit-2
Bit-1
Bit-0
LCR[7] = 0
Baud Rate Generator Divisor
000
DLL
RD/WR
Bit-7
Bit-6
Bit-5
Bit-4
Bit-3
Bit-2
Bit-1
Bit-0
001
DLM
RD/WR
Bit-7
Bit-6
Bit-5
Bit-4
Bit-3
Bit-2
Bit-1
Bit-0
LCR[7]=1
LCR≠0xBF
4.0 INTERNAL REGISTER DESCRIPTIONS
4.1
Receive Holding Register (RHR) - Read- Only
SEE”RECEIVER” ON PAGE 16.
4.2
Transmit Holding Register (THR) - Write-Only
SEE”TRANSMITTER” ON PAGE 14.
4.3
Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR).
20
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
4.3.1
IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR BIT-0 = 1) and receive interrupts (IER BIT-0 = 1) are enabled, the RHR interrupts
(see ISR bits 2 and 3) status will reflect the following:
A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
4.3.2
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR BIT-0 equals a logic 1 for FIFO enable; resetting IER bits 0-3 enables the XR16V554 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can
be used in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates THR is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
• Logic 0 = Disable the receive data ready interrupt (default).
• Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
This bit enables the Transmit Ready interrupt which is issued whenever the THR becomes empty. If the THR is
empty when this bit is enabled, an interrupt will be generated.
• Logic 0 = Disable Transmit Ready interrupt (default).
• Logic 1 = Enable Transmit Ready interrupt.
IER[2]: Receive Line Status Interrupt Enable
If any of the LSR register bits 1, 2, 3 or 4 is a logic 1, it will generate an interrupt to inform the host controller
about the error status of the current data byte in FIFO. LSR bit-1 generates an interrupt immediately when an
overrun occurs. LSR bits 2-4 generate an interrupt when the character in the RHR has an error.
• Logic 0 = Disable the receiver line status interrupt (default).
• Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
• Logic 0 = Disable the modem status register interrupt (default).
• Logic 1 = Enable the modem status register interrupt.
IER[7:4]: Reserved (Default 0)
21
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
4.4
REV. 1.0.1
Interrupt Status Register (ISR)
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others are queued up to be
serviced next. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt
Source Table, Table 9, shows the data values (bit 0-3) for the interrupt priority levels and the interrupt sources
associated with each of these interrupt levels.
4.4.1
Interrupt Generation:
• LSR is by any of the LSR bits 1, 2, 3 and 4.
• RXRDY Data Ready is by RX trigger level.
• RXRDY Data Time-out is by a 4-char plus 12 bits delay timer.
• TXRDY is by TX FIFO empty.
• MSR is by any of the MSR bits 0, 1, 2 and 3.
4.4.2
Interrupt Clearing:
• LSR interrupt is cleared by a read to the LSR register.
• RXRDY interrupt is cleared by reading data until FIFO falls below the trigger level.
• RXRDY Time-out interrupt is cleared by reading RHR.
• TXRDY interrupt is cleared by a read to the ISR register or writing to THR.
• MSR interrupt is cleared by a read to the MSR register.
]
TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
LEVEL
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
1
0
LSR (Receiver Line Status Register)
2
1
1
0
0
RXRDY (Receive Data Time-out)
3
0
1
0
0
RXRDY (Received Data Ready)
4
0
0
1
0
TXRDY (Transmit Ready)
5
0
0
0
0
MSR (Modem Status Register)
-
0
0
0
1
None (default)
ISR[0]: Interrupt Status
• Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
• Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Interrupt Source Table 9).
ISR[4]: Reserved (Default 0)
ISR[5]: Reserved (Default 0)
22
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO trigger levels, and select the
DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
• Logic 0 = Disable the transmit and receive FIFO (default).
• Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
• Logic 0 = No receive FIFO reset (default).
• Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
• Logic 0 = No transmit FIFO reset (default).
• Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[3]: DMA Mode Select
Controls the behavior of the TXRDY and RXRDY pins. See DMA operation section for details.
• Logic 0 = Normal Operation (default).
• Logic 1 = DMA Mode.
FCR[5:4]: Reserved (Default 0)
FCR[7:6]: Receive FIFO Trigger Select
(logic 0 = default, RX trigger level =1)
These 2 bits are used to set the trigger level for the receive FIFO. The UART will issue a receive interrupt when
the number of the characters in the FIFO crosses the trigger level. Table 10 shows the complete selections.
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION
FCR BIT-7
FCR BIT-6
RECEIVE TRIGGER LEVEL
0
0
1
1
0
1
0
1
1
4
8
14
23
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
4.6
REV. 1.0.1
Line Control Register (LCR) - Read/Write
The Line Control Register is used to specify the asynchronous data communication format. The word or
character length, the number of stop bits, and the parity are selected by writing the appropriate bits in this
register.
LCR[1:0]: TX and RX Word Length Select
These two bits specify the word length to be transmitted or received.
BIT-1
BIT-0
WORD LENGTH
0
0
5 (default)
0
1
6
1
0
7
1
1
8
LCR[2]: TX and RX Stop-bit Length Select
The length of stop bit is specified by this bit in conjunction with the programmed word length.
LENGTH
STOP BIT LENGTH
(BIT TIME(S))
0
5,6,7,8
1 (default)
1
5
1-1/2
1
6,7,8
2
BIT-2
WORD
LCR[3]: TX and RX Parity Select
Parity or no parity can be selected via this bit. The parity bit is a simple way used in communications for data
integrity check. See Table 11 for parity selection summary below.
• Logic 0 = No parity.
• Logic 1 = A parity bit is generated during the transmission while the receiver checks for parity error of the
data character received.
LCR[4]: TX and RX Parity Select
If the parity bit is enabled with LCR bit-3 set to a logic 1, LCR BIT-4 selects the even or odd parity format.
• Logic 0 = ODD Parity is generated by forcing an odd number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format (default).
• Logic 1 = EVEN Parity is generated by forcing an even number of logic 1’s in the transmitted character. The
receiver must be programmed to check the same format.
24
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
• LCR BIT-5 = logic 0, parity is not forced (default).
• LCR BIT-5 = logic 1 and LCR BIT-4 = logic 0, parity bit is forced to HIGH for the transmit and receive data.
• LCR BIT-5 = logic 1 and LCR BIT-4 = logic 1, parity bit is forced to LOW for the transmit and receive data.
TABLE 11: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
X
0
No parity
0
0
1
Odd parity
0
1
1
Even parity
1
0
1
Force parity to mark, HIGH
1
1
1
Forced parity to space, LOW
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, logic 0, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
• Logic 0 = No TX break condition. (default)
• Logic 1 = Forces the transmitter output (TX) to a “space”, logic 0, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
• Logic 0 = Data registers are selected (default).
• Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
• Logic 0 = Force DTR# output HIGH (default).
• Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
• Logic 0 = Force RTS# output HIGH (default).
• Logic 1 = Force RTS# output LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the V554. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
25
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
MCR[3]: INT Output Enable
Enable or disable INT outputs to become active or in three-state. This function is associated with the INTSEL
input, see below table for details. This bit is also used to control the OP2# signal during internal loopback
mode. INTSEL pin must be LOW during 68 mode.
• Logic 0 = INT (A-D) outputs disabled (three state) in the 16 mode (default). During internal loopback mode,
OP2# is HIGH.
• Logic 1 = INT (A-D) outputs enabled (active) in the 16 mode. During internal loopback mode, OP2# is LOW.
TABLE 12: INT OUTPUT MODES
INTSEL
PIN
MCR
BIT-3
INT A-D OUTPUTS IN 16 MODE
0
0
Three-State
0
1
Active
1
X
Active
MCR[4]: Internal Loopback Enable
• Logic 0 = Disable loopback mode (default).
• Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
MCR[7:5]: Reserved (Default 0)
4.8
Line Status Register (LSR) - Read/Write
This register is writeable but it is not recommended. The LSR provides the status of data transfers between the
UART and the host. If IER bit-2 is enabled, LSR bit-1 will generate an interrupt immediately and LSR bits 2-4
will generate an interrupt when a character with an error is in the RHR.
LSR[0]: Receive Data Ready Indicator
• Logic 0 = No data in receive holding register or FIFO (default).
• Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
• Logic 0 = No overrun error (default).
• Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
• Logic 0 = No parity error (default).
• Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
• Logic 0 = No framing error (default).
• Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
26
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
LSR[4]: Receive Break Tag
• Logic 0 = No break condition (default).
• Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX
input returns to the idle condition, “mark” or HIGH.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to a logic 1 when the last data byte
is transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0
concurrently with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set
when the transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
This bit is set to a logic 1 whenever the transmitter goes idle. It is set to logic 0 whenever either the THR or
TSR contains a data character. In the FIFO mode this bit is set to a logic 1 whenever the transmit FIFO and
transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
• Logic 0 = No FIFO error (default).
• Logic 1 = A global indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error
or break indication is in the FIFO data. This bit clears when there is no more error(s) in any of the bytes in the
RX FIFO.
4.9
Modem Status Register (MSR) - Read/Write
This register is writeable but it is not recommended. The MSR provides the current state of the modem
interface input signals. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used for general
purpose inputs when they are not used with modem signals.
MSR[0]: Delta CTS# Input Flag
• Logic 0 = No change on CTS# input (default).
• Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
MSR[1]: Delta DSR# Input Flag
• Logic 0 = No change on DSR# input (default).
• Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
MSR[2]: Delta RI# Input Flag
• Logic 0 = No change on RI# input (default).
• Logic 1 = The RI# input has changed from LOW to HIGH, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[3]: Delta CD# Input Flag
• Logic 0 = No change on CD# input (default).
• Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
27
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
MSR[4]: CTS Input Status
A HIGH on the CTS# pin will stop UART transmitter as soon as the current character has finished
transmission, and a LOW will resume data transmission. Normally MSR bit-4 bit is the compliment of the CTS#
input. However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input
may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
Normally this bit is the complement of the DSR# input. In the loopback mode, this bit is equivalent to the DTR#
bit in the MCR register. The DSR# input may be used as a general purpose input when the modem interface is
not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit-2 in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
4.10
Scratch Pad Register (SPR) - Read/Write
This is a 8-bit general purpose register for the user to store temporary data.
4.11
Baud Rate Generator Registers (DLL and DLM) - Read/Write
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and DLL
gives the 16-bit divisor value. See ”Section 2.8, Programmable Baud Rate Generator” on page 13.
28
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
TABLE 13: UART RESET CONDITIONS FOR CHANNELS A-D
REGISTERS
RESET STATE
DLM, DLL
DLM = 0x00 and DLL = 0x01. Only resets to these values during a power up. They do not reset when the
Reset Pin is asserted.
RHR
Bits 7-0 = 0xXX
THR
Bits 7-0 = 0xXX
IER
Bits 7-0 = 0x00
FCR
Bits 7-0 = 0x00
ISR
Bits 7-0 = 0x01
LCR
Bits 7-0 = 0x00
MCR
Bits 7-0 = 0x00
LSR
Bits 7-0 = 0x60
MSR
Bits 3-0 = Logic 0
Bits 7-4 = Logic levels of the inputs inverted
SPR
Bits 7-0 = 0xFF
I/O SIGNALS
RESET STATE
TX
HIGH
RTS#
HIGH
DTR#
HIGH
RXRDY#
HIGH
TXRDY#
LOW
INT
(16 Mode)
XR16V554 = Three-State Condition (INTSEL = LOW)
XR16V554 = LOW (INTSEL = HIGH)
XR16V554D = LOW
IRQ#
(68 Mode)
HIGH (INTSEL = LOW)
29
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
ABSOLUTE MAXIMUM RATINGS
Power Supply Range
4 Volts
Voltage at Any Pin
GND-0.3 V to 5.5 V
Operating Temperature
-40o to +85oC
Storage Temperature
-65o to +150oC
Package Dissipation
500 mW
TYPICAL PACKAGE THERMAL RESISTANCE DATA (MARGIN OF ERROR: ± 15%)
Thermal Resistance (48-QFN)
theta-ja = 28oC/W, theta-jc = 10.5oC/W
Thermal Resistance (64-LQFP)
theta-ja = 50oC/W, theta-jc = 11oC/W
Thermal Resistance (68-PLCC)
theta-ja = 46oC/W, theta-jc = 17oC/W
Thermal Resistance (80-LQFP)
theta-ja = 37oC/W, theta-jc = 7oC/W
ELECTRICAL CHARACTERISTICS
DC ELECTRICAL CHARACTERISTICS
UNLESS OTHERWISE NOTED: TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V
SYMBOL
PARAMETER
LIMITS
2.5V
MIN
MAX
LIMITS
3.3V
MIN
MAX
UNITS
CONDITIONS
VILCK
Clock Input Low Level
-0.3
0.4
-0.3
0.6
V
VIHCK
Clock Input High Level
2.0
VCC
2.4
VCC
V
VIL
Input Low Voltage
-0.3
0.5
-0.3
0.7
V
VIH
Input High Voltage
1.8
5.5
2.0
5.5
V
VOL
Output Low Voltage
0.4
V
V
IOL = 6 mA
V
V
IOH = -4 mA
0.4
VOH
Output High Voltage
2.0
1.8
IIL
Input Low Leakage Current
±15
±15
uA
IIH
Input High Leakage Current
±15
±15
uA
CIN
Input Pin Capacitance
5
5
pF
ICC
Power Supply Current
1.7
3
mA
30
IOL = 4 mA
IOH = -2 mA
Ext Clk = 2MHz
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
AC ELECTRICAL CHARACTERISTICS
TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE
SYMBOL
PARAMETER
LIMITS
2.5V ± 10%
MIN
MAX
LIMITS
3.3V ± 10%
MIN
MAX
UNIT
XTAL1
UART Crystal Frequency
24
24
MHz
ECLK
External Clock Frequency
50
64
MHz
TECLK
External Clock Time Period
10
7
ns
TAS
Address Setup Time (16 Mode)
0
0
ns
TAH
Address Hold Time (16 Mode)
0
0
ns
TCS
Chip Select Width (16 Mode)
50
40
ns
TRD
IOR# Strobe Width (16 Mode)
50
40
ns
TDY
Read Cycle Delay (16 Mode)
50
40
ns
TRDV
Data Access Time (16 Mode)
45
35
ns
TDD
Data Disable Time (16 Mode)
10
10
ns
TWR
IOW# Strobe Width (16 Mode)
50
40
ns
TDY
Write Cycle Delay (16 Mode)
50
40
ns
TDS
Data Setup Time (16 Mode)
10
10
ns
TDH
Data Hold Time (16 Mode)
5
5
ns
TADS
Address Setup (68 Mode)
0
0
ns
TADH
Address Hold (68 Mode)
0
0
ns
TRWS
R/W# Setup to CS# (68 Mode)
0
0
ns
TRDA
Data Access Time (68 mode)
45
35
ns
TRDH
Data Disable Time (68 mode)
10
10
ns
TWDS
Write Data Setup (68 mode)
10
10
ns
TWDH
Write Data Hold (68 Mode)
5
5
ns
TRWH
CS# De-asserted to R/W# De-asserted (68 Mode)
10
5
ns
TCSL
CS# Strobe Width (68 Mode)
50
40
ns
TCSD
CS# Cycle Delay (68 Mode)
50
40
ns
TWDO
Delay From IOW# To Output
50
50
ns
TMOD
Delay To Set Interrupt From MODEM Input
50
50
ns
TRSI
Delay To Reset Interrupt From IOR#
50
50
ns
31
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
AC ELECTRICAL CHARACTERISTICS
TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE
SYMBOL
PARAMETER
LIMITS
2.5V ± 10%
MAX
MIN
LIMITS
3.3V ± 10%
MAX
MIN
UNIT
TSSI
Delay From Stop To Set Interrupt
1
1
Bclk
TRRI
Delay From IOR# To Reset Interrupt
45
45
ns
TSI
Delay From Start To Interrupt
45
45
ns
TINT
Delay From Initial INT Reset To Transmit Start
24
Bclk
TWRI
Delay From IOW# To Reset Interrupt
45
45
ns
TSSR
Delay From Stop To Set RXRDY#
1
1
Bclk
TRR
Delay From IOR# To Reset RXRDY#
45
45
ns
TWT
Delay From IOW# To Set TXRDY#
45
45
ns
TSRT
Delay From Center of Start To Reset TXRDY#
8
8
Bclk
TRST
Reset Pulse Width
Bclk
Baud Clock
8
40
FIGURE 12. CLOCK TIMING
CLK
CLK
EXTERNAL
CLOCK
OSC
32
24
8
40
ns
16X data rate
Hz
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 13. MODEM INPUT/OUTPUT TIMING FOR CHANNELS A-D
IO W #
IO W
A c t iv e
TW
RTS#
DTR#
C h a n g e o f s ta te
DO
C h a n g e o f s ta te
CD#
CTS#
DSR#
C h a n g e o f s ta te
C h a n g e o f s ta te
TMOD
TMOD
IN T
A c t iv e
A c t iv e
A c t iv e
T RSI
IO R #
A c t iv e
A c t iv e
A c t iv e
TMOD
C h a n g e o f s ta te
R I#
FIGURE 14. 16 MODE (INTEL) DATA BUS READ TIMING FOR CHANNELS A-D
A0-A7
Valid Address
TAS
TCS
Valid Address
TAS
TAH
TAH
TCS
CS#
TDY
TRD
TRD
IOR#
TDD
TRDV
D0-D7
Valid Data
TDD
TRDV
Valid Data
RDTm
33
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 15. 16 MODE (INTEL) DATA BUS WRITE TIMING FOR CHANNELS A-D
A0-A7
Valid Address
Valid Address
TAS
TAS
TAH
TCS
TAH
TCS
CS#
TDY
TWR
TWR
IOW#
TDH
TDS
Valid Data
D0-D7
TDH
TDS
Valid Data
16Write
FIGURE 16. 68 MODE (MOTOROLA) DATA BUS READ TIMING FOR CHANNELS A-D
A0-A7
Valid Address
TADS
TCSL
Valid Address
TADH
CS#
TCSD
TRWS
TRWH
R/W#
TRDH
TRDA
D0-D7
Valid Data
Valid Data
68Read
34
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 17. 68 MODE (MOTOROLA) DATA BUS WRITE TIMING FOR CHANNELS A-D
A0-A7
Valid Address
TADS
TCSL
Valid Address
TADH
CS#
TCSD
TRWS
TRWH
R/W#
TWDS
T WDH
Valid Data
D0-D7
Valid Data
68Write
FIGURE 18. RECEIVE READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D
RX
INT
RXRDY#
Start
Bit
D0:D7
Stop
Bit
D0:D7
D0:D7
TSSR
TSSR
TSSR
1 Byte
in RHR
1 Byte
in RHR
1 Byte
in RHR
TSSR
TSSR
Active
Data
Ready
Active
Data
Ready
TRR
TRR
TSSR
Active
Data
Ready
TRR
IOR#
(Reading data
out of RHR)
RXNFM
35
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 19. TRANSMIT READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D
TX
Start
Bit
(Unloading)
IER[1]
enabled
Stop
Bit
D0:D7
D0:D7
ISR is read
D0:D7
ISR is read
ISR is read
INT*
TWRI
TWRI
TWRI
TSRT
TSRT
TSRT
TXRDY#
TWT
TWT
TWT
IOW#
(Loading data
into THR)
*INT is cleared when the ISR is read or when data is loaded into the THR.
TXNonFIFO
FIGURE 20. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA DISABLED] FOR CHANNELS A-D
Start
Bit
RX
S D0:D7
S D0:D7 T
Stop
Bit
D0:D7
S D0:D7 T
S D0:D7 T S D0:D7 T
S D0:D7 T
RX FIFO drops
below RX
Trigger Level
TSSI
INT
FIFO
Empties
TSSR
RX FIFO fills up to RX
Trigger Level or RX Data
Timeout
RXRDY#
First Byte is
Received in
RX FIFO
TRRI
TRR
IOR#
(Reading data out
of RX FIFO)
RXINTDMA#
36
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 21. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA ENABLED] FOR CHANNELS A-D
Start
Bit
RX
Stop
Bit
S D0:D7
S D0:D7 T
D0:D7
S D0:D7 T
S D0:D7 T S D0:D7 T
S D0:D7 T
RX FIFO drops
below RX
Trigger Level
TSSI
INT
RX FIFO fills up to RX
Trigger Level or RX Data
Timeout
FIFO
Empties
TSSR
RXRDY#
TRRI
TRR
IOR#
(Reading data out
of RX FIFO)
RXFIFODMA
FIGURE 22. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE DISABLED] FOR CHANNELS A-D
TX FIFO
Empty
TX
Start
Bit
Stop
Bit
S D0:D7 T
(Unloading)
IER[1]
enabled
Last Data Byte
Transmitted
T S D0:D7 T S D0:D7 T
S D0:D7 T S D0:D7 T
TSI
ISR is read
S D0:D7 T
ISR is read
TSRT
INT*
TX FIFO fills up
to trigger level
TXRDY#
Data in
TX FIFO
TX FIFO
Empty
TWRI
TX FIFO drops
below trigger level
TWT
IOW#
(Loading data
into FIFO)
*INT is cleared when the ISR is read or when TX FIFO fills up to the trigger level.
37
TXDMA#
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
FIGURE 23. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE ENABLED] FOR CHANNELS A-D
Start
Bit
TX
Stop
Bit
Last Data Byte
Transmitted
S D0:D7 T S D0:D7 T
(Unloading)
IER[1]
enabled
D0:D7
S D0:D7 T
ISR Read
S D0:D7 T S D0:D7 T
S D0:D7 T
TSI
TSRT
ISR Read
INT*
TX FIFO fills up
to trigger level
TXRDY#
TX FIFO drops
below trigger level
TWRI
At least 1
empty location
in FIFO
TX FIFO
Full
TWT
IOW#
(Loading data
into FIFO)
*INT cleared when the ISR is read or when TX FIFO fills up to trigger level.
38
TXDMA
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
PACKAGE DIMENSIONS
48 LEAD QUAD FLAT NO LEAD (7 x 7 x 0.9 mm, 0.50 mm pitch QFN)
Note: The actual center pad is
metallic and the size (D2) is
device-dependent with a typical
tolerance of 0.3mm. The lead
may be half-etched terminal.
Note: The control dimension is the millimeter column
INCHES
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
A
0.031
0.039
0.80
1.00
A1
0.000
0.002
0.00
0.05
A3
0.006
0.010
0.15
0.25
D
0.270
0.281
6.85
7.15
D2
0.201
0.209
5.10
5.30
b
0.007
0.012
0.18
0.30
e
0.0197 BSC
0.50 BSC
L
0.012
0.020
0.30
0.50
k
0.008
-
0.20
-
39
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
64 LEAD LOW-PROFILE QUAD FLAT PACK (10 x 10 x 1.4 mm LQFP)
D
D1
48
33
49
32
D1
64
D
17
1
16
B
A2
e
C
A
α
Seating Plane
A1
L
Note: The control dimension is the millimeter column
INCHES
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
A
0.055
0.063
1.40
1.60
A1
0.002
0.006
0.05
0.15
A2
0.053
0.057
1.35
1.45
B
0.007
0.011
0.17
0.27
C
0.004
0.008
0.09
0.20
D
0.465
0.480
11.80
12.20
D1
0.390
0.398
9.90
10.10
e
0.020 BSC
0.50 BSC
L
0.018
0.030
0.45
0.75
α
0°
7°
0°
7°
40
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
68 LEAD PLASTIC LEADED CHIP CARRIER (PLCC)
D
C
Seating Plane
D1
45° x H2
45° x H1
A2
2 1 68
B1
B
D
D3
D1
D2
e
R
D3
A1
A
Note: The control dimension is the inch column
INCHES
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
A
0.165
0.200
4.19
5.08
A1
0.090
0.130
2.29
3.30
A2
0.020
---.
0.51
---
B
0.013
0.021
0.33
0.53
B1
0.026
0.032
0.66
0.81
C
0.008
0.013
0.19
0.32
D
0.985
0.995
25.02
25.27
D1
0.950
0.958
24.13
24.33
D2
0.890
0.930
22.61
23.62
D3
0.800 typ.
20.32 typ.
e
0.050 BSC
1.27 BSC
H1
0.042
0.056
1.07
1.42
H2
0.042
0.048
1.07
1.22
R
0.025
0.045
0.64
1.14
41
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
80 LEAD PLASTIC QUAD FLAT PACK (12 mm x 12 mm LQFP, 1.4 mm Form)
Note: The control dimension is the millimeter column
INCHES
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
A
0.055
0.063
1.40
1.60
A1
0.002
0.006
0.05
0.15
A2
0.053
0.057
1.35
1.45
B
0.007
0.011
0.17
0.27
C
0.004
0.008
0.09
0.20
D
0.543
0.559
13.80
14.20
D1
0.465
0.480
11.80
12.20
e
0.0197 BSC
0.50 BSC
L
0.018
0.030
0.45
0.75
α
0°
7°
0°
7°
42
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
REVISION HISTORY
DATE
REVISION
DESCRIPTION
April 2006
Rev P1.0.0
Preliminary Data Sheet.
July 2006
Rev P1.0.1
Updated AC Electrical Characterstics.
October 2006
Rev P1.0.2
Updated DC Electrical Characteristics.
January 2007
Rev 1.0.0
Final Datasheet.
May 2007
Rev 1.0.1
Updated QFN package dimensions drawing to show minimum "k" parameter.
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to
improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any
circuits described herein, conveys no license under any patent or other right, and makes no representation that
the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration
purposes and may vary depending upon a user’s specific application. While the information in this publication
has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the
failure or malfunction of the product can reasonably be expected to cause failure of the life support system or
to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless
EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has
been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately
protected under the circumstances.
Copyright 2007 EXAR Corporation
Datasheet May 2007.
Send your UART technical inquiry with technical details to hotline: [email protected].
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
43
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
TABLE OF CONTENTS
GENERAL DESCRIPTION ................................................................................................ 1
FEATURES .................................................................................................................................................... 1
APPLICATIONS ............................................................................................................................................... 1
FIGURE 1. XR16V554 BLOCK DIAGRAM ........................................................................................................................................... 1
FIGURE 2. PIN OUT ASSIGNMENT FOR 68-PIN PLCC PACKAGES IN 16 AND 68 MODE AND 64-PIN LQFP PACKAGES.......................... 2
FIGURE 3. PIN OUT ASSIGNMENT FOR 48-PIN QFN PACKAGE AND 80-PIN LQFP PACKAGE ............................................................... 3
PIN DESCRIPTIONS ......................................................................................................... 4
ORDERING INFORMATION................................................................................................................................ 4
1.0 PRODUCT DESCRIPTION....................................................................................................................... 9
2.0 FUNCTIONAL DESCRIPTIONS............................................................................................................. 10
2.1 CPU INTERFACE............................................................................................................................................... 10
FIGURE 4. XR16V554 TYPICAL INTEL/MOTOROLA DATA BUS INTERCONNECTIONS ........................................................................... 10
2.2 DEVICE RESET ................................................................................................................................................. 11
2.3 CHANNEL SELECTION..................................................................................................................................... 11
TABLE 1: CHANNEL A-D SELECT IN 16 MODE ................................................................................................................................. 11
TABLE 2: CHANNEL A-D SELECT IN 68 MODE ................................................................................................................................. 11
2.4 CHANNELS A-D INTERNAL REGISTERS ....................................................................................................... 12
2.5 INT OUPUTS FOR CHANNELS A-D ................................................................................................................. 12
TABLE 3: INT PIN OPERATION FOR TRANSMITTER FOR CHANNELS A-D ........................................................................................... 12
TABLE 4: INT PIN OPERATION FOR RECEIVER FOR CHANNELS A-D ................................................................................................. 12
2.6 DMA MODE........................................................................................................................................................ 12
TABLE 5: TXRDY# AND RXRDY# OUTPUTS IN FIFO AND DMA MODE FOR CHANNELS A-D ........................................................... 13
2.7 CRYSTAL OSCILLATOR OR EXTERNAL CLOCK INPUT .............................................................................. 13
FIGURE 5. TYPICAL CRYSTAL CONNECTIONS................................................................................................................................... 13
2.8 PROGRAMMABLE BAUD RATE GENERATOR .............................................................................................. 13
FIGURE 6. BAUD RATE GENERATOR ............................................................................................................................................... 14
TABLE 6: TYPICAL DATA RATES WITH A 14.7456 MHZ CRYSTAL OR EXTERNAL CLOCK ...................................................................... 14
2.9 TRANSMITTER .................................................................................................................................................. 14
2.9.1 TRANSMIT HOLDING REGISTER (THR) - WRITE ONLY ...........................................................................................
2.9.2 TRANSMITTER OPERATION IN NON-FIFO MODE ....................................................................................................
FIGURE 7. TRANSMITTER OPERATION IN NON-FIFO MODE ..............................................................................................................
2.9.3 TRANSMITTER OPERATION IN FIFO MODE .............................................................................................................
FIGURE 8. TRANSMITTER OPERATION IN FIFO AND FLOW CONTROL MODE .....................................................................................
15
15
15
15
15
2.10 RECEIVER ....................................................................................................................................................... 16
2.10.1 RECEIVE HOLDING REGISTER (RHR) - READ-ONLY ............................................................................................ 16
FIGURE 9. RECEIVER OPERATION IN NON-FIFO MODE .................................................................................................................... 16
FIGURE 10. RECEIVER OPERATION IN FIFO.................................................................................................................................... 17
2.11 INTERNAL LOOPBACK ................................................................................................................................. 18
FIGURE 11. INTERNAL LOOP BACK IN CHANNEL A AND B ................................................................................................................ 18
3.0 UART INTERNAL REGISTERS ............................................................................................................. 19
TABLE 7: UART CHANNEL A AND B UART INTERNAL REGISTERS ....................................................................................... 19
TABLE 8: INTERNAL REGISTERS DESCRIPTION. ................................................................................................................... 20
4.0 INTERNAL REGISTER DESCRIPTIONS............................................................................................... 20
4.1 RECEIVE HOLDING REGISTER (RHR) - READ- ONLY .................................................................................. 20
4.2 TRANSMIT HOLDING REGISTER (THR) - WRITE-ONLY ............................................................................... 20
4.3 INTERRUPT ENABLE REGISTER (IER) - READ/WRITE................................................................................. 20
4.3.1 IER VERSUS RECEIVE FIFO INTERRUPT MODE OPERATION ............................................................................... 21
4.3.2 IER VERSUS RECEIVE/TRANSMIT FIFO POLLED MODE OPERATION .................................................................. 21
4.4 INTERRUPT STATUS REGISTER (ISR) ........................................................................................................... 22
4.4.1 INTERRUPT GENERATION: ........................................................................................................................................ 22
4.4.2 INTERRUPT CLEARING: ............................................................................................................................................. 22
TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL ....................................................................................................................... 22
4.5 FIFO CONTROL REGISTER (FCR) - WRITE-ONLY......................................................................................... 23
TABLE 10: RECEIVE FIFO TRIGGER LEVEL SELECTION ................................................................................................................... 23
4.6 LINE CONTROL REGISTER (LCR) - READ/WRITE......................................................................................... 24
TABLE 11: PARITY SELECTION ........................................................................................................................................................ 25
4.7 MODEM CONTROL REGISTER (MCR) OR GENERAL PURPOSE OUTPUTS CONTROL - READ/WRITE.. 25
TABLE 12: INT OUTPUT MODES ..................................................................................................................................................... 26
4.8 LINE STATUS REGISTER (LSR) - READ/WRITE ............................................................................................ 26
4.9 MODEM STATUS REGISTER (MSR) - READ/WRITE...................................................................................... 27
I
XR16V554/554D
2.25V TO 3.6V QUAD UART WITH 16-BYTE FIFO
REV. 1.0.1
4.10 SCRATCH PAD REGISTER (SPR) - READ/WRITE ....................................................................................... 28
4.11 BAUD RATE GENERATOR REGISTERS (DLL AND DLM) - READ/WRITE................................................. 28
TABLE 13: UART RESET CONDITIONS FOR CHANNELS A-D ................................................................................................. 29
ABSOLUTE MAXIMUM RATINGS ................................................................................. 30
TYPICAL PACKAGE THERMAL RESISTANCE DATA (MARGIN OF ERROR: ± 15%) 30
ELECTRICAL CHARACTERISTICS............................................................................... 30
DC ELECTRICAL CHARACTERISTICS............................................................................................................. 30
AC ELECTRICAL CHARACTERISTICS ............................................................................................................. 31
TA = -40O TO +85OC, VCC IS 2.25 TO 3.6V, 70 PF LOAD WHERE APPLICABLE ............................................. 31
FIGURE 12. CLOCK TIMING............................................................................................................................................................. 32
FIGURE 13. MODEM INPUT/OUTPUT TIMING FOR CHANNELS A-D .................................................................................................... 33
FIGURE 14. 16 MODE (INTEL) DATA BUS READ TIMING FOR CHANNELS A-D ................................................................................... 33
FIGURE 15. 16 MODE (INTEL) DATA BUS WRITE TIMING FOR CHANNELS A-D .................................................................................. 34
FIGURE 16. 68 MODE (MOTOROLA) DATA BUS READ TIMING FOR CHANNELS A-D........................................................................... 34
FIGURE 18. RECEIVE READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D ............................................................ 35
FIGURE 17. 68 MODE (MOTOROLA) DATA BUS WRITE TIMING FOR CHANNELS A-D ......................................................................... 35
FIGURE 19. TRANSMIT READY & INTERRUPT TIMING [NON-FIFO MODE] FOR CHANNELS A-D .......................................................... 36
FIGURE 20. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA DISABLED] FOR CHANNELS A-D........................................... 36
FIGURE 21. RECEIVE READY & INTERRUPT TIMING [FIFO MODE, DMA ENABLED] FOR CHANNELS A-D............................................ 37
FIGURE 22. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE DISABLED] FOR CHANNELS A-D .............................. 37
FIGURE 23. TRANSMIT READY & INTERRUPT TIMING [FIFO MODE, DMA MODE ENABLED] FOR CHANNELS A-D ............................... 38
PACKAGE DIMENSIONS................................................................................................................................ 39
REVISION HISTORY ..................................................................................................................................... 43
I
TABLE OF CONTENTS .....................................................................................................
II