EXAR XRT75R12DIB

XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
DECEMBER 2006
REV. 1.0.1
GENERAL DESCRIPTION
The XRT75R12D is a twelve channel fully integrated
Line Interface Unit (LIU) featuring EXAR’s R3
Technology (Reconfigurable, Relayless Redundancy)
for E3/DS3/STS-1 applications. The LIU incorporates
12 independent Receivers, Transmitters and Jitter
Attenuators in a single 420 Lead TBGA package.
Each channel of the XRT75R12D can be
independently configured to operate in E3 (34.368
MHz), DS3 (44.736 MHz) or STS-1 (51.84 MHz).
Each transmitter can be turned off and tri-stated for
redundancy support or for conserving power.
The XRT75R12D’s differential receiver provides high
noise interference margin and is able to receive data
over 1000 feet of cable or with up to 12 dB of cable
attenuation.
The XRT75R12D incorporates an advanced crystalless jitter attenuator per channel that can be selected
either in the transmit or receive path. The jitter
attenuator performance meets the ETSI TBR-24 and
Bellcore GR-499 specifications. Also, the jitter
attenuators can be used for clock smoothing in
SONET STS-1 to DS-3 de-mapping.
The XRT75R12D provides a Parallel Microprocessor
Interface for programming and control.
The XRT75R12D supports analog, remote and digital
loop-backs. The device also has a built-in Pseudo
Random Binary Sequence (PRBS) generator and
detector with the ability to insert and detect single bit
error for diagnostic purposes.
APPLICATIONS
• E3/DS3 Access Equipment
• DSLAMs
• Digital Cross Connect Systems
• CSU/DSU Equipment
• Routers
• Fiber Optic Terminals
FIGURE 1. BLOCK DIAGRAM OF THE XRT 75R12D
CS
RD
WR
Addr[7:0]
D[7:0]
PCLK
RDY
XRT75R12D
XRT75R12D
CLKOUT_n
µProcessor Interface
SFM_en
RLOL_n
INT
Pmode
RESET
RTIP_n
RRing_n
AGC/
Equalizer
Slicer
TTIP_n
TRing_n
MTIP_n
MRing_n
DMO_n
ICT
Line
Driver
Device
Monitor
Clock & Data
Recovery
Jitter
Attenuator
LOS
Detector
Local
LoopBack
E3Clk
DS3Clk
STS-Clk/12M
Clock
Synthesizer
Peak Detector
MUX
HDB3/
B3ZS
Decoder
RxClk_n
RxPOS_n
RxNEG/LCV_n
Remote
LoopBack
RLOS_n
Tx
Pulse
Shaping
Tx
Control
Timing
Control
Jitter
Attenuator
MUX
HDB3/
B3ZS
Encoder
TxClk_n
TxPOS_n
TxNEG_n
TxON
Channel 0
Channel n...
Channel 11
ORDERING INFORMATION
PART NUMBER
PACKAGE
OPERATING TEMPERATURE RANGE
XRT75R12DIB
420 Lead TBGA
-40°C to +85°C
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
• Each channel supports Analog, Remote and Digital
FEATURES
Loop-backs
RECEIVER
• R3
Technology
Redundancy)
(Reconfigurable,
• Single 3.3 V ± 5% power supply
• 5 V Tolerant digital inputs
• Available in 420 pin TBGA Thermally enhanced
Relayless
• On chip Clock and Data Recovery circuit for high
Package
input jitter tolerance
• - 40°C to 85°C Industrial Temperature Range
• Meets E3/DS3/STS-1 Jitter Tolerance Requirement
• Detects and Clears LOS as per G.775
• Receiver Monitor mode handles up to 20 dB flat
TRANSMIT INTERFACE CHARACTERISTICS
• Accepts either Single-Rail or Dual-Rail data from
Terminal Equipment and generates a bipolar signal
to the line
loss with 6 dB cable attenuation
• On chip B3ZS/HDB3 encoder and decoder that can
• Integrated Pulse Shaping Circuit
• Built-in B3ZS/HDB3 Encoder (which can be
be either enabled or disabled
• On-chip clock synthesizer provides the appropriate
disabled)
rate clock from a single 12.288 MHz Clock
• Provides low jitter output clock
• Accepts Transmit Clock with duty cycle of 30%-
TRANSMITTER
• Generates pulses that comply with the ITU-T G.703
•
R3
Technology
Redundancy)
70%
(Reconfigurable,
Relayless
pulse template for E3 applications
• Generates pulses that comply with the DSX-3 pulse
• Compliant with Bellcore GR-499, GR-253 and ANSI
template, as specified in Bellcore GR-499-CORE
and ANSI T1.102_1993
T1.102 Specification for transmit pulse
• Generates pulses that comply with the STSX-1
• Tri-state Transmit output capability for redundancy
pulse template, as specified in Bellcore GR-253CORE
applications
• Each Transmitter can be independently turned on
• Transmitter can be turned off in order to support
or off
redundancy designs
• Transmitters provide Voltage Output Drive
RECEIVE INTERFACE CHARACTERISTICS
JITTER ATTENUATOR
• Integrated Adaptive Receive Equalization (optional)
• On chip advanced crystal-less Jitter Attenuator for
for optimal Clock and Data Recovery
each channel
• Declares and Clears the LOS defect per ITU-T
• Jitter Attenuator can be selected in Receive,
G.775 requirements for E3 and DS3 applications
Transmit path, or disabled
• Meets Jitter Tolerance Requirements, as specified
• Meets ETSI TBR 24 Jitter Transfer Requirements
• Compliant with jitter transfer template outlined in
in ITU-T G.823_1993 for E3 Applications
• Meets Jitter Tolerance Requirements, as specified
ITU G.751, G.752, G.755 and GR-499-CORE,1995
standards
in Bellcore GR-499-CORE for DS3 Applications
• Declares Loss of Lock (LOL) Alarm
• Built-in B3ZS/HDB3 Decoder (which can be
• 16 or 32 bits selectable FIFO size
CONTROL AND DIAGNOSTICS
disabled)
• Parallel Microprocessor Interface for control and
• Recovered Data can be muted while the LOS
configuration
• Supports
optional
internal
Transmit
Condition is declared
driver
• Outputs either Single-Rail or Dual-Rail data to the
monitoring
Terminal Equipment
2
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE OF CONTENTS
GENERAL DESCRIPTION.............................................................................................................. 1
APPLICATIONS ............................................................................................................................................................... 1
FIGURE 1. BLOCK DIAGRAM OF THE XRT 75R12D.................................................................................................................................. 1
ORDERING INFORMATION .................................................................................................................... 1
FEATURES ..................................................................................................................................................................... 2
TRANSMIT INTERFACE CHARACTERISTICS ....................................................................................................................... 2
RECEIVE INTERFACE CHARACTERISTICS ......................................................................................................................... 2
PIN DESCRIPTIONS (BY FUNCTION) ........................................................................................... 3
SYSTEM-SIDE TRANSMIT INPUT AND TRANSMIT CONTROL PINS ....................................................................................... 3
SYSTEM-SIDE RECEIVE OUTPUT AND RECEIVE CONTROL PINS ....................................................................................... 6
RECEIVE LINE SIDE PINS ............................................................................................................................................... 8
CLOCK INTERFACE......................................................................................................................................................... 9
GENERAL CONTROL PINS ............................................................................................................................................ 10
POWER SUPPLY PINS .................................................................................................................................................. 12
GROUND PINS ............................................................................................................................................................. 13
TABLE 1: LIST BY PIN NUMBER ............................................................................................................................................................. 14
FUNCTIONAL DESCRIPTION ...................................................................................................... 18
1.0 R3 TECHNOLOGY (RECONFIGURABLE, RELAYLESS REDUNDANCY) ....................................... 18
1.1 NETWORK ARCHITECTURE ......................................................................................................................... 18
FIGURE 2. NETWORK REDUNDANCY ARCHITECTURE .............................................................................................................................. 18
2.0 CLOCK SYNTHESIZER ....................................................................................................................... 19
FIGURE 3. SIMPLIFIED BLOCK DIAGRAM OF THE INPUT CLOCK CIRCUITRY DRIVING THE MICROPROCESSOR ............................................ 19
TABLE 2: REFERENCE CLOCK PERFORMANCE SPECIFICATIONS .............................................................................................................. 19
2.1 CLOCK DISTRIBUTION ................................................................................................................................. 20
FIGURE 4. CLOCK DISTRIBUTION CONGIFURED IN E3 MODE WITHOUT USING SFM ................................................................................ 20
3.0 THE RECEIVER SECTION .................................................................................................................. 21
FIGURE 5. RECEIVE PATH BLOCK DIAGRAM .......................................................................................................................................... 21
3.1 RECEIVE LINE INTERFACE .......................................................................................................................... 21
FIGURE 6. RECEIVE LINE INTERFACECONNECTION ................................................................................................................................. 21
3.2 ADAPTIVE GAIN CONTROL (AGC) .............................................................................................................. 21
3.3 RECEIVE EQUALIZER ................................................................................................................................... 22
FIGURE 7. ACG/EQUALIZER BLOCK DIAGRAM ....................................................................................................................................... 22
3.3.1 RECOMMENDATIONS FOR EQUALIZER SETTINGS .............................................................................................. 22
3.4 CLOCK AND DATA RECOVERY ................................................................................................................... 22
3.4.1 DATA/CLOCK RECOVERY MODE ............................................................................................................................ 22
3.4.2 TRAINING MODE........................................................................................................................................................ 22
3.5 LOS (LOSS OF SIGNAL) DETECTOR ........................................................................................................... 23
3.5.1 DS3/STS-1 LOS CONDITION ..................................................................................................................................... 23
TABLE 3: THE ALOS (ANALOG LOS) DECLARATION AND CLEARANCE THRESHOLDS FOR A GIVEN SETTING OF REQEN (DS3 AND STS-1 APPLICATIONS).......................................................................................................................................................................... 23
3.5.2 DISABLING ALOS/DLOS DETECTION ..................................................................................................................... 23
3.5.3 E3 LOS CONDITION:.................................................................................................................................................. 23
FIGURE 8. LOSS OF SIGNAL DEFINITION FOR E3 AS PER ITU-T G.775 .................................................................................................. 23
FIGURE 9. LOSS OF SIGNAL DEFINITION FOR E3 AS PER ITU-T G.775................................................................................................... 24
3.5.4 INTERFERENCE TOLERANCE.................................................................................................................................. 24
FIGURE 10. INTERFERENCE MARGIN TEST SET UP FOR DS3/STS-1 ...................................................................................................... 24
FIGURE 11. INTERFERENCE MARGIN TEST SET UP FOR E3. ................................................................................................................... 24
TABLE 4: INTERFERENCE MARGIN TEST RESULTS ................................................................................................................................. 25
3.5.5 MUTING THE RECOVERED DATA WITH LOS CONDITION:................................................................................... 26
FIGURE 12. RECEIVER DATA OUTPUT AND CODE VIOLATION TIMING ........................................................................................................ 26
3.6 B3ZS/HDB3 DECODER .................................................................................................................................. 26
4.0 THE TRANSMITTER SECTION ........................................................................................................... 27
FIGURE 13.
FIGURE 14.
FIGURE 15.
FIGURE 16.
TRANSMIT PATH BLOCK DIAGRAM ...................................................................................................................................... 27
TYPICAL INTERFACE BETWEEN TERMINAL EQUIPMENT AND THE XRT75R12D (DUAL-RAIL DATA)............................................ 27
TRANSMITTER TERMINAL INPUT TIMING ............................................................................................................................... 28
SINGLE-RAIL OR NRZ DATA FORMAT (ENCODER AND DECODER ARE ENABLED) .................................................................. 28
4.1 TRANSMIT CLOCK ........................................................................................................................................ 29
4.2 B3ZS/HDB3 ENCODER .................................................................................................................................. 29
4.2.1 B3ZS ENCODING ....................................................................................................................................................... 29
FIGURE 18. B3ZS ENCODING FORMAT ................................................................................................................................................. 29
I
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
4.2.2 HDB3 ENCODING....................................................................................................................................................... 29
FIGURE 17. DUAL-RAIL DATA FORMAT (ENCODER AND DECODER ARE DISABLED).................................................................................... 29
FIGURE 19. HDB3 ENCODING FORMAT ................................................................................................................................................. 30
4.3 TRANSMIT PULSE SHAPER ......................................................................................................................... 30
FIGURE 20. TRANSMIT PULSE SHAPE TEST CIRCUIT .............................................................................................................................. 30
4.3.1 GUIDELINES FOR USING TRANSMIT BUILD OUT CIRCUIT .................................................................................. 30
4.4 E3 LINE SIDE PARAMETERS ........................................................................................................................ 31
FIGURE 21. PULSE MASK FOR E3 (34.368 MBITS/S) INTERFACE AS PER ITU-T G.703 ............................................................................. 31
TABLE 5: E3 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS .............................................................. 31
FIGURE 22. BELLCORE GR-253 CORE TRANSMIT OUTPUT PULSE TEMPLATE FOR SONET STS-1 APPLICATIONS ................................. 32
TABLE 6: STS-1 PULSE MASK EQUATIONS ........................................................................................................................................... 32
TABLE 7: STS-1 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS (GR-253)..................................... 33
FIGURE 23. TRANSMIT OUPUT PULSE TEMPLATE FOR DS3 AS PER BELLCORE GR-499 ......................................................................... 34
TABLE 8: DS3 PULSE MASK EQUATIONS ............................................................................................................................................... 34
TABLE 9: DS3 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS (GR-499) ........................................ 35
4.5 TRANSMIT DRIVE MONITOR ........................................................................................................................ 36
FIGURE 24. TRANSMIT DRIVER MONITOR SET-UP................................................................................................................................... 36
4.6 TRANSMITTER SECTION ON/OFF ............................................................................................................... 36
5.0 JITTER ..................................................................................................................................................37
5.1 JITTER TOLERANCE ..................................................................................................................................... 37
FIGURE 25. JITTER TOLERANCE MEASUREMENTS .................................................................................................................................. 37
5.1.1 DS3/STS-1 JITTER TOLERANCE REQUIREMENTS ................................................................................................ 37
FIGURE 26. INPUT JITTER TOLERANCE FOR DS3/STS-1 ...................................................................................................................... 38
5.1.2 E3 JITTER TOLERANCE REQUIREMENTS .............................................................................................................. 38
FIGURE 27. INPUT JITTER TOLERANCE FOR E3..................................................................................................................................... 38
TABLE 10: JITTER AMPLITUDE VERSUS MODULATION FREQUENCY (JITTER TOLERANCE) ......................................................................... 39
5.2 JITTER TRANSFER ........................................................................................................................................ 39
TABLE 11: JITTER TRANSFER SPECIFICATION/REFERENCES ................................................................................................................... 39
5.3 JITTER ATTENUATOR ................................................................................................................................... 39
TABLE 12: JITTER TRANSFER PASS MASKS ........................................................................................................................................... 40
FIGURE 28. JITTER TRANSFER REQUIREMENTS AND JITTER ATTENUATOR PERFORMANCE ...................................................................... 40
5.3.1 JITTER GENERATION................................................................................................................................................ 40
6.0 DIAGNOSTIC FEATURES ...................................................................................................................41
6.1 PRBS GENERATOR AND DETECTOR ......................................................................................................... 41
FIGURE 29. PRBS MODE ................................................................................................................................................................... 41
6.2 LOOPBACKS .................................................................................................................................................. 42
6.2.1 ANALOG LOOPBACK................................................................................................................................................ 42
FIGURE 30. ANALOG LOOPBACK ........................................................................................................................................................... 42
6.2.2 DIGITAL LOOPBACK ................................................................................................................................................. 43
FIGURE 31. DIGITAL LOOPBACK ............................................................................................................................................................ 43
6.2.3 REMOTE LOOPBACK ................................................................................................................................................ 43
FIGURE 32. REMOTE LOOPBACK ........................................................................................................................................................... 43
6.3 TRANSMIT ALL ONES (TAOS) ...................................................................................................................... 44
FIGURE 33. TRANSMIT ALL ONES (TAOS) ............................................................................................................................................ 44
7.0 MICROPROCESSOR INTERFACE BLOCK ........................................................................................45
TABLE 13: SELECTING THE MICROPROCESSOR INTERFACE MODE .......................................................................................................... 45
FIGURE 34. SIMPLIFIED BLOCK DIAGRAM OF THE MICROPROCESSOR INTERFACE BLOCK ........................................................................ 45
7.1 THE MICROPROCESSOR INTERFACE BLOCK SIGNALS ......................................................................... 46
TABLE 14: XRT75R12D MICROPROCESSOR INTERFACE SIGNALS ......................................................................................................... 46
7.2 ASYNCHRONOUS AND SYNCHRONOUS DESCRIPTION .......................................................................... 47
FIGURE 35. ASYNCHRONOUS µP INTERFACE SIGNALS DURING PROGRAMMED I/O READ AND WRITE OPERATIONS .................................. 47
TABLE 15: ASYNCHRONOUS TIMING SPECIFICATIONS ............................................................................................................................. 48
FIGURE 36. SYNCHRONOUS µP INTERFACE SIGNALS DURING PROGRAMMED I/O READ AND WRITE OPERATIONS.................................... 48
TABLE 16: SYNCHRONOUS TIMING SPECIFICATIONS ............................................................................................................................... 49
7.3 REGISTER MAP ............................................................................................................................................. 50
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D ........................................................................................... 50
THE GLOBAL/CHIP-LEVEL REGISTERS ................................................................................................................ 59
TABLE 18: LIST AND ADDRESS LOCATIONS OF GLOBAL REGISTERS ........................................................................................................ 59
REGISTER DESCRIPTION - GLOBAL REGISTERS ............................................................................................... 59
TABLE 19:
TABLE 20:
TABLE 21:
TABLE 22:
TABLE 23:
APS/REDUNDANCY TRANSMIT CONTROL REGISTER - CR0 (ADDRESS LOCATION = 0X00) ..................................................... 59
APS/REDUNDANCY TRANSMIT CONTROL REGISTER - CR8 (ADDRESS LOCATION = 0X08) ..................................................... 60
CHANNEL LEVEL INTERRUPT ENABLE REGISTER - CR96 (ADDRESS LOCATION = 0X60) ......................................................... 61
CHANNEL LEVEL INTERRUPT ENABLE REGISTER - CR224 (ADDRESS LOCATION = 0XE0)....................................................... 62
CHANNEL LEVEL INTERRUPT STATUS REGISTER - CR97 (ADDRESS LOCATION = 0X61) ......................................................... 63
II
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.1
TABLE 24: CHANNEL LEVEL INTERRUPT STATUS REGISTER - CR225 (ADDRESS LOCATION = 0XE1)....................................................... 64
TABLE 25: DEVICE/PART NUMBER REGISTER - CR110 (ADDRESS LOCATION = 0X6E) ........................................................................... 64
TABLE 26: CHIP REVISION NUMBER REGISTER - CR111 (ADDRESS LOCATION = 0X6F) ......................................................................... 65
THE PER-CHANNEL REGISTERS........................................................................................................................... 66
REGISTER DESCRIPTION - PER CHANNEL REGISTERS .................................................................................... 66
TABLE 27:
TABLE 28:
TABLE 29:
TABLE 30:
TABLE 31:
TABLE 32:
TABLE 33:
TABLE 34:
TABLE 35:
TABLE 36:
TABLE 37:
TABLE 38:
TABLE 39:
TABLE 40:
XRT75R12D REGISTER MAP SHOWING INTERRUPT ENABLE REGISTERS (IER_N) ............................................................... 66
SOURCE LEVEL INTERRUPT ENABLE REGISTER - CHANNEL N ADDRESS LOCATION = 0XM1 .................................................... 67
XRT75R12D REGISTER MAP SHOWING ALARM STATUS REGISTERS (AS_N)........................................................................ 69
XRT75R12 REGISTER MAP SHOWING ALARM STATUS REGISTERS (AS_N) .......................................................................... 71
XRT75R12D REGISTER MAP SHOWING TRANSMIT CONTROL REGISTERS (TC_N) ................................................................ 75
XRT75R12D REGISTER MAP SHOWING RECEIVE CONTROL REGISTERS (RC_N).................................................................. 77
XRT75R12D REGISTER MAP SHOWING CHANNEL CONTROL REGISTERS (CC_N)................................................................. 79
XRT75R12D REGISTER MAP SHOWING JITTER ATTENUATOR CONTROL REGISTERS (JA_N)................................................. 81
XRT75R12D REGISTER MAP SHOWING ERROR COUNTER MSBYTE REGISTERS (EM_N) ..................................................... 82
ERROR COUNTER MSBYTE REGISTER - CHANNEL N ADDRESS LOCATION = 0XMA................................................................. 83
XRT75R12D REGISTER MAP SHOWING ERROR COUNTER LSBYTE REGISTERS (EL_N) ....................................................... 83
ERROR COUNTER LSBYTE REGISTER - CHANNEL N ADDRESS LOCATION = 0XMB.................................................................. 84
XRT75R12D REGISTER MAP SHOWING ERROR COUNTER HOLDING REGISTERS (EH_N) ..................................................... 84
ERROR COUNTER HOLDING REGISTER - CHANNEL N ADDRESS LOCATION = 0XMC ................................................................ 85
8.0 THE SONET/SDH DE-SYNC FUNCTION WITHIN THE LIU ............................................................... 86
8.1 BACKGROUND AND DETAILED INFORMATION - SONET DE-SYNC APPLICATIONS ........................... 86
FIGURE 37. A SIMPLE ILLUSTRATION OF A DS3 SIGNAL BEING MAPPED INTO AND TRANSPORTED OVER THE SONET NETWORK ............... 87
8.2 MAPPING/DE-MAPPING JITTER/WANDER ................................................................................................. 88
8.2.1 HOW DS3 DATA IS MAPPED INTO SONET ............................................................................................................. 88
FIGURE 38. A SIMPLE ILLUSTRATION OF THE SONET STS-1 FRAME ..................................................................................................... 89
FIGURE 39. A SIMPLE ILLUSTRATION OF THE STS-1 FRAME STRUCTURE WITH THE TOH AND THE ENVELOPE CAPACITY BYTES DESIGNATED
90
FIGURE 40. THE BYTE-FORMAT OF THE TOH WITHIN AN STS-1 FRAME ................................................................................................. 91
FIGURE 41. THE BYTE-FORMAT OF THE TOH WITHIN AN STS-1 FRAME ................................................................................................. 92
FIGURE 42. ILLUSTRATION OF THE BYTE STRUCTURE OF THE STS-1 SPE ............................................................................................. 93
FIGURE 43. AN ILLUSTRATION OF TELCORDIA GR-253-CORE'S RECOMMENDATION ON HOW MAP DS3 DATA INTO AN STS-1 SPE ......... 94
FIGURE 44. A SIMPLIFIED "BIT-ORIENTED" VERSION OF TELCORDIA GR-253-CORE'S RECOMMENDATION ON HOW TO MAP DS3 DATA INTO AN
STS-1 SPE.......................................................................................................................................................................... 94
8.2.2 DS3 FREQUENCY OFFSETS AND THE USE OF THE "STUFF OPPORTUNITY" BITS ......................................... 95
FIGURE 45. A SIMPLE ILLUSTRATION OF A DS3 DATA-STREAM BEING MAPPED INTO AN STS-1 SPE, VIA A PTE .................................... 96
FIGURE 46. AN ILLUSTRATION OF THE STS-1 SPE TRAFFIC THAT WILL BE GENERATED BY THE "SOURCE" PTE, WHEN MAPPING IN A DS3 SIGNAL
THAT HAS A BIT RATE OF 44.736MBPS + 1PPM, INTO AN STS-1 SIGNAL .................................................................................. 98
FIGURE 47. AN ILLUSTRATION OF THE STS-1 SPE TRAFFIC THAT WILL BE GENERATED BY THE SOURCE PTE, WHEN MAPPING A DS3 SIGNAL
THAT HAS A BIT RATE OF 44.736MBPS - 1PPM, INTO AN STS-1 SIGNAL ................................................................................... 99
8.3
JITTER/WANDER DUE TO POINTER ADJUSTMENTS .............................................................................. 99
8.3.1 THE CONCEPT OF AN STS-1 SPE POINTER......................................................................................................... 100
FIGURE 48. AN ILLUSTRATION OF AN STS-1 SPE STRADDLING ACROSS TWO CONSECUTIVE STS-1 FRAMES ......................................... 100
FIGURE 49. THE BIT-FORMAT OF THE 16-BIT WORD (CONSISTING OF THE H1 AND H2 BYTES) WITH THE 10 BITS, REFLECTING THE LOCATION OF
THE J1 BYTE, DESIGNATED .................................................................................................................................................. 101
FIGURE 50. THE RELATIONSHIP BETWEEN THE CONTENTS OF THE "POINTER BITS" (E.G., THE 10-BIT EXPRESSION WITHIN THE H1 AND H2 BYTES)
AND THE LOCATION OF THE J1 BYTE WITHIN THE ENVELOPE CAPACITY OF AN STS-1 FRAME ................................................ 101
8.3.2 POINTER ADJUSTMENTS WITHIN THE SONET NETWORK ................................................................................ 101
8.3.3 CAUSES OF POINTER ADJUSTMENTS ................................................................................................................. 102
FIGURE 51. AN ILLUSTRATION OF AN STS-1 SIGNAL BEING PROCESSED VIA A SLIP BUFFER .................................................................. 103
FIGURE 52. AN ILLUSTRATION OF THE BIT FORMAT WITHIN THE 16-BIT WORD (CONSISTING OF THE H1 AND H2 BYTES) WITH THE "I" BITS DESIGNATED ............................................................................................................................................................................. 104
FIGURE 53. AN ILLUSTRATION OF THE BIT-FORMAT WITHIN THE 16-BIT WORD (CONSISTING OF THE H1 AND H2 BYTES) WITH THE "D" BITS DESIGNATED ............................................................................................................................................................................. 105
8.3.4 WHY ARE WE TALKING ABOUT POINTER ADJUSTMENTS? ............................................................................. 106
8.4 CLOCK GAPPING JITTER ........................................................................................................................... 106
FIGURE 54. ILLUSTRATION OF THE TYPICAL APPLICATIONS FOR THE LIU IN A SONET DE-SYNC APPLICATION ...................................... 106
8.5 A REVIEW OF THE CATEGORY I INTRINSIC JITTER REQUIREMENTS (PER TELCORDIA GR-253-CORE)
FOR DS3 APPLICATIONS .......................................................................................................................... 107
TABLE 41: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3 APPLICATIONS ...... 107
8.5.1 DS3 DE-MAPPING JITTER....................................................................................................................................... 108
8.5.2 SINGLE POINTER ADJUSTMENT ........................................................................................................................... 108
FIGURE 55. ILLUSTRATION OF SINGLE POINTER ADJUSTMENT SCENARIO ............................................................................................. 108
8.5.3 POINTER BURST...................................................................................................................................................... 109
FIGURE 56. ILLUSTRATION OF BURST OF POINTER ADJUSTMENT SCENARIO ......................................................................................... 109
8.5.4 PHASE TRANSIENTS............................................................................................................................................... 109
III
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 57. ILLUSTRATION OF "PHASE-TRANSIENT" POINTER ADJUSTMENT SCENARIO .......................................................................... 110
8.5.5 87-3 PATTERN.......................................................................................................................................................... 110
FIGURE 58. AN ILLUSTRATION OF THE 87-3 CONTINUOUS POINTER ADJUSTMENT PATTERN .................................................................. 110
8.5.6 87-3 ADD ................................................................................................................................................................... 111
FIGURE 59. ILLUSTRATION OF THE 87-3 ADD POINTER ADJUSTMENT PATTERN ..................................................................................... 111
8.5.7 87-3 CANCEL............................................................................................................................................................ 111
FIGURE 60. ILLUSTRATION OF 87-3 CANCEL POINTER ADJUSTMENT SCENARIO .................................................................................... 112
8.5.8 CONTINUOUS PATTERN......................................................................................................................................... 112
FIGURE 61. ILLUSTRATION OF CONTINUOUS PERIODIC POINTER ADJUSTMENT SCENARIO .................................................................... 112
8.5.9 CONTINUOUS ADD ................................................................................................................................................. 113
FIGURE 62. ILLUSTRATION OF CONTINUOUS-ADD POINTER ADJUSTMENT SCENARIO ............................................................................. 113
8.5.10 CONTINUOUS CANCEL......................................................................................................................................... 113
FIGURE 63. ILLUSTRATION OF CONTINUOUS-CANCEL POINTER ADJUSTMENT SCENARIO ....................................................................... 114
8.6 A REVIEW OF THE DS3 WANDER REQUIREMENTS PER ANSI T1.105.03B-1997. ................................ 114
8.7 A REVIEW OF THE INTRINSIC JITTER AND WANDER CAPABILITIES OF THE LIU IN A TYPICAL SYSTEM
APPLICATION .............................................................................................................................................. 114
8.7.1 INTRINSIC JITTER TEST RESULTS........................................................................................................................ 114
TABLE 42: SUMMARY OF "CATEGORY I INTRINSIC JITTER TEST RESULTS" FOR SONET/DS3 APPLICATIONS ......................................... 115
8.7.2 WANDER MEASUREMENT TEST RESULTS.......................................................................................................... 116
8.8 DESIGNING WITH THE LIU ......................................................................................................................... 116
8.8.1 HOW TO DESIGN AND CONFIGURE THE LIU TO PERMIT A SYSTEM TO MEET THE ABOVE-MENTIONED INTRINSIC JITTER AND WANDER REQUIREMENTS........................................................................................................... 116
FIGURE 64. ILLUSTRATION OF THE LIU BEING CONNECTED TO A MAPPER IC FOR SONET DE-SYNC APPLICATIONS .............................. 116
CHANNEL CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X06................................................................... 117
CHANNEL 1 ADDRESS LOCATION = 0X0E .......................................................... 117
CHANNEL 2 ADDRESS LOCATION = 0X16 ........................................................... 117
CHANNEL CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X06................................................................... 118
CHANNEL 1 ADDRESS LOCATION = 0X0E ............................................................... 118
CHANNEL 2 ADDRESS LOCATION = 0X16 ................................................................. 118
JITTER ATTENUATOR CONTROL REGISTER - (CHANNEL 0 ADDRESS LOCATION = 0X07................................................. 118
CHANNEL 1 ADDRESS LOCATION = 0X0F.................................................... 118
CHANNEL 2 ADDRESS LOCATION = 0X17 .................................................... 118
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07.................................................. 119
CHANNEL 1 ADDRESS LOCATION = 0X0F.............................................. 119
CHANNEL 2 ADDRESS LOCATION = 0X17 .............................................. 119
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07.................................................. 119
CHANNEL 1 ADDRESS LOCATION = 0X0F............................................. 119
CHANNEL 2 ADDRESS LOCATION = 0X17 ............................................. 119
8.8.2 RECOMMENDATIONS ON PRE-PROCESSING THE GAPPED CLOCKS (FROM THE MAPPER/ASIC DEVICE) PRIOR
TO ROUTING THIS DS3 CLOCK AND DATA-SIGNALS TO THE TRANSMIT INPUTS OF THE LIU ...................... 119
FIGURE 65. ILLUSTRATION OF MINOR PATTERN P1 ......................................................................................................................... 120
FIGURE 66. ILLUSTRATION OF MINOR PATTERN P2 ......................................................................................................................... 121
FIGURE 67. ILLUSTRATION OF PROCEDURE WHICH IS USED TO SYNTHESIZE MAJOR PATTERN A....................................................... 121
FIGURE 68. ILLUSTRATION OF MINOR PATTERN P3 ......................................................................................................................... 122
FIGURE 69. ILLUSTRATION OF PROCEDURE WHICH IS USED TO SYNTHESIZE PATTERN B ................................................................... 122
FIGURE 70. ILLUSTRATION OF THE SUPER PATTERN WHICH IS OUTPUT VIA THE "OC-N TO DS3" MAPPER IC ................................... 123
FIGURE 71. SIMPLE ILLUSTRATION OF THE LIU BEING USED IN A SONET DE-SYNCHRONIZER" APPLICATION ......................................... 123
8.8.3 HOW DOES THE LIU PERMIT THE USER TO COMPLY WITH THE SONET APS RECOVERY TIME REQUIREMENTS
OF 50MS (PER TELCORDIA GR-253-CORE)? .......................................................................................................... 123
TABLE 43: MEASURED APS RECOVERY TIME AS A FUNCTION OF DS3 PPM OFFSET ............................................................................. 124
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07.................................................. 125
CHANNEL 1 ADDRESS LOCATION = 0X0F............................................. 125
CHANNEL 2 ADDRESS LOCATION = 0X17 ............................................. 125
8.8.4 HOW SHOULD ONE CONFIGURE THE LIU, IF ONE NEEDS TO SUPPORT "DAISY-CHAIN" TESTING AT THE END
CUSTOMER'S SITE? ................................................................................................................................................... 125
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07.................................................. 125
CHANNEL 1 ADDRESS LOCATION = 0X0F.................................................... 125
CHANNEL 2 ADDRESS LOCATION = 0X17 .................................................... 125
9.0 ELECTRICAL CHARACTERISTICS ..................................................................................................126
TABLE 44: ABSOLUTE MAXIMUM RATINGS ........................................................................................................................................... 126
TABLE 45: DC ELECTRICAL CHARACTERISTICS:................................................................................................................................... 126
ORDERING INFORMATION.................................................................................................................128
PACKAGE DIMENSIONS - ............................................................................................................................................ 128
IV
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REVISIONS ................................................................................................................................................................ 129
V
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
PIN DESCRIPTIONS (BY FUNCTION)
SYSTEM-SIDE TRANSMIT INPUT AND TRANSMIT CONTROL PINS
PIN #
SIGNAL NAME
TYPE
P4
TxON
I
DESCRIPTION
Transmit On/Off Input
Upon power up, the transmitters are powered on. Turning the transmitters
On or Off is selected through the microprocessor interface by programming
the appropriate channel register if this pin is pulled "High". If the TxON pin
is pulled "Low", all 12 transmitters are powered off.
NOTE: TxON is ideal for redundancy applications. See the R3 Technology
section of this datasheet for more details. Internally pulled "High".
F22
AA22
H22
Y23
G26
AA25
G1
AA2
H5
Y4
F5
AA5
TxCLK0
TxCLK1
TxCLK2
TxCLK3
TxCLK4
TxCLK5
TxCLK6
TxCLK7
TxCLK8
TxCLK9
TxCLK10
TxCLK11
I
E23
AB24
J22
AA23
G25
AA26
G2
AA1
J5
AA4
E4
AB3
TxPOS0
TxPOS1
TxPOS2
TxPOS3
TxPOS4
TxPOS5
TxPOS6
TxPOS7
TxPOS8
TxPOS9
TxPOS10
TxPOS11
I
Transmit Clock Input
These input pins have three functions:
• They function as the timing source for the Transmit Section of the
corresponding channel within the XRT75R12D.
• They are used by the Transmit Section of the LIU IC to sample the
corresponding TxPOS_n and TxNEG_n input pins.
• They are used to clock the PRBS generator
NOTE: The user is expected to supply a 44.736MHz ± 20ppm clock signal
(for DS3 applications), 34.368MHz ± 20 ppm clock signal (for E3
applications) or a 51.84MHz ± 4.6ppm clock signal (for STS-1,
Stratum 3E or better applications).
Transmit Positive Data Input
The function of these digitial input pins depends upon whether the corresponding channel has been configured to operate in the Single-Rail or
Dual-Rail Mode.
Single Rail Mode - Transmit Data Input
Operating in the Single-Rail Mode; all transmit input data will be serially
applied to this input pin. This signal will be latched into the Transmit Section circuitry on the active edge of the TxCLK_n signal.
The Transmit Section of the LIU IC will then encode this data into either the
B3ZS line code (for DS3 and STS-1 applications) or the HDB3 line code
(for E3 applications).
Dual Rail Mode - Transmit Positive Data Input
In the Dual-Rail Mode, the user should apply a pulse to this input pin when
a positive-polarity pulse is to be transmitted onto the line. This signal will
be latched into the Transmit Section circuitry upon the active edge of the
TxCLK_n signal,.
The Transmit Section of the LIU IC will NOT encode this data into either the
B3ZS or HDB3 line codes. If the user configures the LIU IC to operate in
the Dual-Rail Mode, B3ZS/HDB3 encoding must have already been done
prior to this input.
3
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
SYSTEM-SIDE TRANSMIT INPUT AND TRANSMIT CONTROL PINS
PIN #
SIGNAL NAME
TYPE
C25
AB25
H23
W23
H24
Y26
H3
Y1
H4
W4
C2
AB2
TxNEG0
TxNEG1
TxNEG2
TxNEG3
TxNEG4
TxNEG5
TxNEG6
TxNEG7
TxNEG8
TxNEG9
TxNEG10
TxNEG11
I
B24
AE24
C20
AD20
C16
AD16
C11
AD11
C7
AD7
C3
AD3
TTip0
TTip1
TTip2
TTip3
TTip4
TTip5
TTip6
TTip7
TTip8
TTip9
TTip10
TTip11
O
C24
AD24
B20
AE20
B16
AE16
B11
AE11
B7
AE7
B3
AE3
TRing0
TRing1
TRing2
TRing3
TRing4
TRing5
TRing6
TRing7
TRing8
TRing9
TRing10
TRing11
O
DESCRIPTION
Transmit Negative Data Input
When a Channel has been configured to operate in the Dual-Rail Mode,
the user should apply a pulse to this input pin anytime the Transmit Section
of the LIU IC to generate a negative-polarity pulse onto the line. This signal
will be latched into the Transmit Section circuitry upon the active edge of
the TxCLK_n signal.
NOTE: In the Single-Rail Mode, this input pin has no function, and should
be tied to GND.
Transmit TTIP Output - Positive Polarity Signal
These output pins along with the corresponding TRING_n output pins,
function as the Transmit DS3/E3/STS-1 Line output signal drivers for a
given channel of the XRT75R12D.
Connect this signal and the corresponding TRING_n output signal to a 1:1
transformer.
Whenever the Transmit Section of the Channel generates and transmits a
positive-polarity pulse onto the line, this output pin will be pulsed to a high
ervoltage than its corresponding TRING_n output pins.
Conversely, whenever the Transmit Section of the Channel generates and
transmit a negative-polarity pulse onto the line, this output pin will be
pulsed to a lower voltage than its corresponding TRING_n output pin.
NOTE: This output pin will be tri-stated whenever the TxON input pin or bitfield is set to "0".
Transmit Ring Output - Negative Polarity Signal
These output pins along with the corresponding TTIP_n output pins, function as the Transmit DS3/E3/STS-1 Line output signal drivers for a given
channel, within the XRT75R12D.
Connect this signal and the corresponding TTIP_n output signal to a 1:1
transformer.
Whenever the Transmit Section of the Channel generates and transmits a
positive-polarity pulse onto the line, this output pin will be pulsed to a lower
voltage than its corresponding TTIP_n output pin.
Conversely, whenever the Transmit Section of the Channel generates and
transmit a negative-polarity pulse onto the line, this output pin will be
pulsed to a higher voltage than its corresponding TTIP_n output pin.
NOTE: This output pin will be tri-stated whenever the TxON input pin or bitfield is set to "0".
4
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
SYSTEM-SIDE TRANSMIT INPUT AND TRANSMIT CONTROL PINS
PIN #
SIGNAL NAME
TYPE
C23
AD23
D19
AC19
D15
AC15
E11
AB11
E8
AB8
C4
AD4
MTip0
MTip1
MTip2
MTip3
MTip4
MTip5
MTip6
MTip7
MTip8
MTip9
MTip10
MTip11
I
D23
AC23
E19
AB19
E16
AB16
D10
AC10
D8
AC8
D4
AC4
MRing0
MRing1
MRing2
MRing3
MRing4
MRing5
MRing6
MRing7
MRing8
MRing9
MRing10
MRing11
I
N3
N4
N5
N1
M1
L2
M2
M3
M4
M5
K2
J1
DMO0
DMO1
DMO2
DMO3
DMO4
DMO5
DMO6
DMO7
DMO8
DMO9
DMO10
DMO11
O
DESCRIPTION
Monitor Tip Input - Positive Polarity Signal
These input pins along with MRing_n function as the Transmit Drive Monitor Output (DMO) input monitoring pins. (1) To monitor the Transmit Output line signal and (2) to perform this monitoring externally, then this pin
MUST be connected to the corresponding TTIP_n output pin via a 270W
series resistor. Similarly, the MRING_n input pin MUST also be connected
to its corresponding TRING_n output pin via a 270W series resistor.
The MTIP_n and MRING_n input pins will continuously monitor the Transmit Output line signal via the TTIP_n and TRING_n output pins for bipolar
activity. If these pins do not detect any bipolar activity for 128 bit periods,
then the Transmit Drive Monitor circuit will drive the corresponding DMO_n
output pin "High" in order to denote a possible fault condition in the Transmit Output Line signal path.
NOTE:
These input pins are inactive if the user chooses to internally
monitor the Transmit Output line signal.
Monitor Ring Input
These input pins along with MTIP_n function as the Transmit Drive Monitor
Output (DMO) input monitoring pins. (1) To monitor the Transmit Output
line signal and (2) to perform this monitoring externally, then this input pin
MUST be connected to the corresponding TRING_n output pin via a 270W
series resistor. Similarly, the MTIP_n input pin MUST be connected to its
corresponding TTIP_n output pin via a 270W series resistor.
The MTIP_n and MRING_n input pins will continuously monitor the Transmit Output line signal via the TTIP_n and TRING_n output pins for bipolar
activity. If these pins do not detect any bipolar activity for 128 bit periods,
then the Transmit Drive Monitor circuit will drive the corresponding DMO_n
output pin "High" to indicate a possible fault condition in the Transmit Output Line signal path.
NOTE:
These input pins are inactive if the user chooses to internally
monitor the Transmit Output line signal.
Drive Monitor Output
These output signals are used to indicate a fault condition within the Transmit Output signal path.
This output pin will toggle "High" anytime the Transmit Drive Monitor circuitry either, via the corresponding MTIP and MRING input pins or internally, detects no bipolar pulses via the Transmit Output line signal (e.g., via
the TTIP_m and TRING_m output pins) for 128 bit-periods.
This output pin will be driven "Low" anytime the Transmit Drive Monitor circuitry has detected at least one bipolar pulse via the Transmit Output line
signal within the last 128 bit periods.
5
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
SYSTEM-SIDE RECEIVE OUTPUT AND RECEIVE CONTROL PINS
PIN #
SIGNAL NAME
TYPE
D25
AD25
G23
AA24
J24
U24
J3
U3
G4
AA3
D2
AD2
RLOS0
RLOS1
RLOS2
RLOS3
RLOS4
RLOS5
RLOS6
RLOS7
RLOS8
RLOS9
RLOS10
RLOS11
O
G22
AB26
K22
U22
L24
W25
L3
W2
K5
U5
G5
AB1
RLOL0
RLOL1
RLOL2
RLOL3
RLOL4
RLOL5
RLOL6
RLOL7
RLOL8
RLOL9
RLOL10
RLOL11
O
E25
AD26
G24
Y24
L22
T22
L5
T5
G3
Y3
E2
AD1
RxPOS0
RxPOS1
RxPOS2
RxPOS3
RxPOS4
RxPOS5
RxPOS6
RxPOS7
RxPOS8
RxPOS9
RxPOS10
RxPOS11
O
DESCRIPTION
Receive Loss of Signal Output Indicator
This output pin indicates Loss of Signal (LOS) Defect condition for the corresponding channel.
"Low" - Indicates that the corresponding Channel is NOT currently declaring the
LOS defect condition.
"High" - Indicates that the corresponding Channel is currently declaring the LOS
defect condition.
Receive Loss of Lock Output Indicator
This output pin indicates Loss of Lock (LOL) condition for the corresponding
channel.
"Low" - Indicates that the corresponding Channel is NOT declaring the LOL
condition.
"High" - Indicates that the corresponding Channel is currently declaring the LOL
condition.
NOTE: The Receive Section of a given channel will declare the LOL condition
anytime the frequency of the Recovered Clock (RCLK) signal differs
from that of the reference clock programmed for that channel by 0.5%
or more.
Receive Positive Data Output
The function of these output pins depends upon whether the channel has been
configured to operate in the Single-Rail or Dual-Rail Mode.
Dual-Rail Mode - Receive Positive Polarity Data Output
If the channel has been configured to operate in the Dual-Rail Mode, then all
positive-polarity data will be output via this pin. The negative-polarity data will
be output via the corresponding RxNEG_n pin. In other words, the Receive
Section of the corresponding Channel will pulse this output pin "High" for one
period of RCLK_n anytime it receives a positive-polarity pulse via the RTIP/
RRING input pins.
The data output via this pin is updated upon the active edge of RxCLK_n output
clock signal.
Single-Rail Mode - Receive Data Output
In the Single-Rail Mode, all Receive (or Recovered) data will be output via this
pin.
The data output via this pin is updated upon the active edge of RxCLK_n output
clock signal.
6
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
SYSTEM-SIDE RECEIVE OUTPUT AND RECEIVE CONTROL PINS
PIN #
SIGNAL NAME
TYPE
F23
AC26
F24
U23
L23
T24
L4
T3
F3
U4
F4
AC1
RxNEG/LCV0
RxNEG/LCV1
RxNEG/LCV2
RxNEG/LCV3
RxNEG/LCV4
RxNEG/LCV5
RxNEG/LCV6
RxNEG/LCV7
RxNEG/LCV8
RxNEG/LCV9
RxNEG/LCV10
RxNEG/LCV11
O
E24
AC25
J23
V23
K24
T23
K3
T4
J4
V4
E3
AC2
RxCLK0
RxCLK1
RxCLK2
RxCLK3
RxCLK4
RxCLK5
RxCLK6
RxCLK7
RxCLK8
RxCLK9
RxCLK10
RxCLK11
O
DESCRIPTION
Receive Negative Data Output/Line Code Violation
The function of these pins depends on whether the XRT75R12D is configured in
Single Rail or Dual Rail mode.
Dual-Rail Mode - Receive Negative Polarity Data Output
In the Dual-Rail Mode, all negative-polarity data will be output via this pin. The
positive-polarity data will be output via the corresponding RxPOS_n output pin.
In other words, the Receive Section of the corresponding Channel will pulse this
output pin "High" for one period of RxCLK_n anytime it receives a negativepolarity pulse via the RTIP/RRING input pins.
The data output via this pin is updated upon the active edge of the RCLK_n
output clock signal.
Single-Rail Mode - Line Code Violation Indicator Output
In the Single-Rail Mode, this output pin will function as the Line Code Violation
indicator output.
In this configuration, the Receive Section of the Channel will pulse this output
pin "High" for at least one RCLK period whenever it detects either an LCV (Line
Code Violation) or an EXZ (Excessive Zero Event).
The data that is output via this pin is updated upon the active edge of the
RCLK_n output clock signal.
Receive Clock Output
This output pin functions as the Receive or recovered clock signal. All Receive
(or recovered) data will output via the RxPOS_n and RxNEG_n outputs upon
the active edge of this clock signal.
Additionally, if the device/channel has been configured to operate in the SingleRail Mode, then the RNEG_n/LCV_n output pins will also be updated upon the
active edge of this clock signal.
7
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
RECEIVE LINE SIDE PINS
PIN #
SIGNAL NAME
TYPE
B22
AE22
B18
AE18
A14
AF14
D13
AC13
B9
AE9
B5
AE5
RTip0
RTip1
RTip2
RTip3
RTip4
RTip5
RTip6
RTip7
RTip8
RTip9
RTip10
RTip11
I
C22
AD22
C18
AD18
B14
AE14
C13
AD13
C9
AD9
C5
AD5
RRing0
RRing1
RRing2
RRing3
RRing4
RRing5
RRing6
RRing7
RRing8
RRing9
RRing10
RRing11
I
DESCRIPTION
Receive TIP Input
These input pins along with the corresponding RRing_n input pin function as the
Receive DS3/E3/STS-1 Line input signal for a given channel of the
XRT75R12D.
Cconnect this signal and the corresponding RRING_n input signal to a 1:1
transformer.
Whenever the RTIP/RRING input pins are receiving a positive-polarity pulse
within the incoming DS3, E3 or STS-1 line signal, this input pin will be pulsed to
a higher voltage than its corresponding RRING_n input pin.
Conversely, whenever the RTIP/RRING input pins are receiving a negativepolarity pulse within the incoming DS3, E3 or STS-1 line signal, this input pin
will be pulsed to a lower voltage than its corresponding RRING_n input pin.
Receive Ring Input
These input pins along with the corresponding RTIP_n input pin function as the
Receive DS3/E3/STS-1 Line input signal for a given channel of the
XRT75R12D.
Connect this signal and the corresponding RTIP_n input signal to a 1:1 transformer. (See Figure 6)
Whenever the RTIP/RRING input pins are receiving a positive-polarity pulse
within the incoming DS3, E3 or STS-1 line signal, then this input pin will be
pulsed to a lower voltage than its corresponding RTIP_n input pin.
Conversely, whenever the RTIP/RRING input pins are receiving a negativepolarity pulse within the incoming DS3, E3 or STS-1 line signal, then this input
pin will be pulsed to a higher voltage than its corresponding RTIP_n input pin.
8
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
CLOCK INTERFACE
PIN #
SIGNAL NAME
TYPE
R5
SFM_EN
I
DESCRIPTION
Single Frequency Mode Enable
This input pin is used to configure the XRT75R12D to operate in the SFM (Single Frequency Mode).
When this feature is invoked, the SFM Synthesizer will become active. By
applying a 12.288MHz clock signal to the STS-1Clk/12M pin, the XRT75R12D
will generate all of the appropriate clock signals (e.g., 34.368MHz, 44.736MHz
or 51.84). The XRT75R12D internal circuitry will route each of these synthesized clock signals to the appropriate nodes of the corresponding channels in
the XRT75R12D.
"Low" - Disables the Single Frequency Mode. In this setting, the user is
required to supply to the E3CLK, DS3CLK or STS-1CLK input pins all of the relevant clock signals that are to be used within the chip.
"High" - Enables the Single-Frequency Mode.
NOTE: This input pin is internally pulled low.
R1
E3Clk
I
E3 Clock Input (34.368 MHz ± 20 ppm)
If any one of the channels is configured in E3 mode, a reference clock of 34.368
MHz ± 20 ppm is applied to this input pin. If the LIU is used in E3 mode only,
this pin must be connected to the DS3Clk input pin to have access to the internal microprocessor.
NOTE: SFM mode negates the need for this clock
T1
DS3Clk
I
DS3 Clock Input (44.736 MHz ± 20 ppm)
If any one of the channels is configured in DS3 mode, a reference clock of
44.736 MHz ± 20 ppm is applied to this input pin.
NOTE: SFM mode negates the need for this clock
U1
STS-1Clk/12M
I
STS-1 Clock Input (51.84 MHz ± 20 ppm)
If any one of the channels is configured in STS-1 mode, a reference clock of
51.84MHz ± 20 ppm is applied to this input pin. If the LIU is used in STS-1
mode only, this pin must be connected to the DS3Clk input pin to have access
to the internal microprocessor.
Single Frequency Mode Clock Input (12.288MHz ± 20 ppm)
In Single Frequency Mode, a reference clock of 12.288 MHz ± 20 ppm is connected to this pin and the internal clock synthesizer generates the appropriate
clock frequencies based on the configuration of the rates (E3, DS3 or STS-1).
C26
W22
K23
W24
J25
V25
J2
V2
K4
W3
C1
W5
CLKOUT0
CLKOUT1
CLKOUT2
CLKOUT3
CLKOUT4
CLKOUT5
CLKOUT6
CLKOUT7
CLKOUT8
CLKOUT9
CLKOUT10
CLKOUT11
O
Reference Clock Out
A reference clock pin is provided for each channel that will supply a precise data
rate frequency derived from either the Clock input pin (E3Clk, DS3Clk, or STS1Clk) or the 12.288MHz input in SFM mode. This frequency will be as stable as
the original source. It is designed to provide the attached framer with its appropriate reference clock.
9
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
GENERAL CONTROL PINS
PIN #
SIGNAL NAME
TYPE
P3
TEST
****
DESCRIPTION
Factory Test Mode Input Pin
This pin must be connected to GND for normal operation.
NOTE: This input pin is internally pulled "Low".
AE25
TRST
Test Reset
I
Test Boundary Scan
AB23
TMS
Test Mode Select
I
Test Boundary Scan
AB5
TCK
Test Clock
I
Test Boundary Scan
AB4
TDI
Test Data Input
I
Test Boundary Scan
AE2
TDO
O
Test Data Output
Test Boundary Scan
MICROPROCESSOR PARALLEL INTERFACE PIN #
SIGNAL NAME
TYPE
J26
Pmode
I
DESCRIPTION
This pin controls the Microprocessor Parallel Interface mode.
"High" sets a Synchronous clocked interface mode with a clock from the Host.
"Low" sets an Asynchronous mode where a clock internal to the XRT75R12D will
time the operations.
P24
PCLK
I
High speed clock supplied by the Host to provide timing in the Synchronous
Interface mode. This signal must be a square-wave.
N24
CS
I
Chip Select Input (active low)
Initiates a read or write operation. When "High", no parallel communication is
active between the LIU and the Host.
N22
WR
I
Write Input (active low)
Enables the Host to write data D[7:0] into the LIU register space at address
Addr[7:0].
N23
RD
I
Read Input (active low)
Commands the LIU to transfer the contents of a register specified by Addr[7:0] to
the Host.
N25
RDY
O
Ready Line Output (active low)
Provides a handshake between the LIU and the Host that communicates when
an operation has been completed.
NOTE: This pin must be pulled "High" with a 3kΩ ± 1% resistor.
10
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
MICROPROCESSOR PARALLEL INTERFACE PIN #
SIGNAL NAME
TYPE
DESCRIPTION
K25
M22
M23
M24
K26
L26
M26
N26
Addr0
Addr1
Addr2
Addr3
Addr4
Addr5
Addr6
Addr7
I
An eight bit direct address bus that specifies the source/destination register for a
Read or Write operation.
P22
R26
T26
U26
R25
R24
R23
R22
D0
D1
D2
D3
D4
D5
D6
D7
I/O
An eight bit bi-directional data bus that provides the data into the LIU for a Write
operation or the data out to the Host for a Read operation.
P26
INT
O
Interrupt Active Output (active low)
Normally, this output pin will be pulled "High". However, if the user enables
interrupts within the LIU, and if those conditions occur, the XRT75R12D will signal an interrupt from the Microprocessor by pulling this output pin "Low". The
Host Microprocessor must ascertain the source of the interrupt and service it.
Reading the source of the interupt will clear the flag and the INT pin will go back
high unless another interrupt has gone active.
NOTES:
N2
RESET
I
1.
This pin will remain "Low" until the Interrupt has been serviced.
2.
This pin must be pulled "High" with a 3kΩ ± 1% resistor.
RESET Input
Pulsing this input "Low" causes the XRT75R12D to reset the contents of the onchip Command Registers to their default values. As a consequence, the
XRT75R12D will then also be operating in its default condition.
For normal operation this input pin should be at a logic "High".
NOTE: This input pin is internally pulled high.
11
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
POWER SUPPLY PINS
PIN NAME
PIN NUMBERS
RVDD0
RVDD1
RVDD2
RVDD3
RVDD4
RVDD5
RVDD6
RVDD7
RVDD8
RVDD9
RVDD10
RVDD11
D22
AC22
D18
AC18
E15
AB15
E12
AB12
A9
AF9
D5
AC5
Receive Analog Power Supply (3.3V ±5%)
TVDD0
TVDD1
TVDD2
TVDD3
TVDD4
TVDD5
TVDD6
TVDD7
TVDD8
TVDD9
TVDD10
TVDD11
B23
AE23
B19
AE19
B15
AE15
B10
AE10
A6
AF6
B4
AE4
Transmit Analog Power Supply (3.3V ±5%)
AVDD
M25, T25, AB21, AB18,
AF13, AF12, AB9, AB6, R4,
K1, E6, E9, A12, A13, E18,
E21,
Analog Power Supply (3.3V ±5%)
D26, F25, H25, P25, W26,
V24, Y22, AF21, AF20, AF17,
AF16, AD14, AD12, AF11,
AF8, AF7, AF24, AD6, AF3,
Y5, V3, W1, P5, P2, H2, F2,
D1, C6, A7, A3, A8, A11, C12,
C14, A16, A17, A20, A21,
A24
Digital Power Supply (3.3V ±5%)
DVDD
DESCRIPTION
RVDD should not be shared with other power supplies. It is recommended
that RVDD be isolated from the digital power supply DVDD and the analog
power supply TVDD. For best results, use an internal power plane for isolation. If an internal power plane is not available, a ferrite bead can be used.
Each power supply pin should be bypassed to ground through an external
0.1µF capacitor.
TVDD can be shared with DVDD. However, it is recommended that TVDD be
isolated from the analog power supply RVDD. For best results, use an internal power plane for isolation. If an internal power plane is not available, a ferrite bead can be used. Each power supply pin should be bypassed to ground
through an external 0.1µF capacitor.
AVDD should be isolated from the digital power supplies. For best results,
use an internal power plane for isolation. If an internal power plane is not
available, a ferrite bead can be used. Each power supply pin should be
bypassed to ground through at least one 0.1µF capacitor.
DVDD should be isolated from the analog power supplies. For best results,
use an internal power plane for isolation. If an internal power plane is not
available, a ferrite bead can be used. Every two DVDD power supply pins
should be bypassed to ground through at least one 0.1µF capacitor.
12
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
GROUND PINS
PIN NAME
PIN NUMBERS
DESCRIPTION
RGND0
RGND1
RGND2
RGND3
RGND4
RGND5
RGND6
RGND7
RGND8
RGND9
RGND10
RGND11
A22
AF22
A18
AF18
E14
AB14
E13
AB13
D9
AC9
A5
AF5
Receive Analog Ground
TGND0
TGND1
TGND2
TGND3
TGND4
TGND5
TGND6
TGND7
TGND8
TGND9
TGND10
TGND11
A23
AF23
A19
AF19
A15
AF15
A10
AF10
B6
AE6
A4
AF4
Transmit Analog Ground
It’s recommended that all ground pins of this device be tied together.
It’s recommended that all ground pins of this device be tied together.
AGND
A1, A2, A25, A26, B1, B2, Analog Ground
B25, B26, C8, C10, C17, C19, It’s recommended that all ground pins of this device be tied together.
C21, D17, D21, E5, E22, L25,
U25, AB22, AB20, AB17,
AB10, AB7, R3, L1, E7, E10,
B12, B13, E17, E20, T2, U2,
AC17, AC21, AD8, AD10,
AD15, AD17, AD19, AD21,
AE1, AE26, AE12, AE13,
AF1, AF2, AF25, AF26, C15
DGND
E26, F26, H26, P23, , V26, Digital Ground
Y25, V22, AC24, AC20,
It’s recommended that all ground pins of this device be tied together.
AC16, AC14, AC12, AC11,
AE8, AE17, AE21, AC7, AC6,
AC3, V5, Y2, V1, R2, P1, H1,
F1, E1, D3, D7, B8, D6, D11,
D12, D14, D16, B17, D20,
B21, D24
13
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 1: LIST BY PIN
NUMBER
PIN
PIN NAME
PIN
PIN NAME
PIN
PIN NAME
B7
TRing8
C15
AGND
D23
MRing0
PIN
PIN NAME
B8
DGND
C16
TTip4
D24
DGND
A1
AGND
B9
RTip8
C17
AGND
D25
RLOS0
A2
AGND
B10
TVDD6
C18
RRing2
D26
DVDD
A3
DVDD
B11
TRing6
C19
AGND
E1
DGND
A4
TGND10
B12
AGND
C20
TTip2
E2
RxPOS10
A5
RGND10
B13
AGND
C21
AGND
E3
RxCLK10
A6
TVDD8
B14
RRing4
C22
RRing0
E4
TxPOS10
A7
DVDD
B15
TVDD4
C23
MTip0
E5
AGND
A8
DVDD
B16
TRing4
C24
TRing0
E6
AVDD
A9
RVDD8
B17
DGND
C25
TxNEG0
E7
AGND
A10
TGND6
B18
RTip2
C26
CLKOUT0
E8
MTip8
A11
DVDD
B19
TVDD2
D1
DVDD
E9
AVDD
A12
AVDD
B20
TRing2
D2
RLOS10
E10
AGND
A13
AVDD
B21
DGND
D3
DGND
E11
MTip6
A14
RTip4
B22
RTip0
D4
MRing10
E12
RVDD6
A15
TGND4
B23
TVDD0
D5
RVDD10
E13
RGND6
A16
DVDD
B24
TTip0
D6
DGND
E14
RGND4
A17
DVDD
B25
AGND
D7
DGND
E15
RVDD4
A18
RGND2
B26
AGND
D8
MRing8
E16
MRing4
A19
TGND2
C1
CLKOUT10
D9
RGND8
E17
AGND
A20
DVDD
C2
TxNEG10
D10
MRing6
E18
AVDD
A21
DVDD
C3
TTip10
D11
DGND
E19
MRing2
A22
RGND0
C4
MTip10
D12
DGND
E20
AGND
A23
TGND0
C5
RRing10
D13
RTip6
E21
AVDD
A24
DVDD
C6
DVDD
D14
DGND
E22
AGND
A25
AGND
C7
TTip8
D15
MTip4
E23
TxPOS0
A26
AGND
C8
AGND
D16
DGND
E24
RxCLK0
B1
AGND
C9
RRing8
D17
AGND
E25
RxPOS0
B2
AGND
C10
AGND
D18
RVDD2
E26
DGND
B3
TRing10
C11
TTip6
D19
MTip2
F1
DGND
B4
TVDD10
C12
DVDD
D20
DGND
F2
DVDD
B5
RTip10
C13
RRing6
D21
AGND
F3
RxNEG/LCV8
B6
TGND8
C14
DVDD
D22
RVDD0
F4
RxNEG/LCV10
14
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
PIN
PIN NAME
PIN
PIN NAME
PIN
PIN NAME
PIN
PIN NAME
F5
TxCLK10
J25
CLKOUT4
N3
DMO0
T23
RxCLK5
F22
TxCLK0
J26
Pmode
N4
DMO1
T24
RxNEG/LCV5
F23
RxNEG/LCV0
K1
AVDD
N5
DMO2
T25
AVDD
F24
RxNEG/LCV2
K2
DMO10
N22
WR
T26
D2
F25
DVDD
K3
RxCLK6
N23
RD
U1
STS-1Clk/12M
F26
DGND
K4
CLKOUT8
N24
CS
U2
AGND
G1
TxCLK6
K5
RLOL8
N25
RDY
U3
RLOS7
G2
TxPOS6
K22
RLOL2
N26
Addr7
U4
RxNEG/LCV9
G3
RxPOS8
K23
CLKOUT2
P1
DGND
U5
RLOL9
G4
RLOS8
K24
RxCLK4
P2
DVDD
U22
RLOL3
G5
RLOL10
K25
Addr0
P3
TEST
U23
RxNEG/LCV3
G22
RLOL0
K26
Addr4
P4
TxON
U24
RLOS5
G23
RLOS2
L1
AGND
P5
DVDD
U25
AGND
G24
RxPOS2
L2
DMO5
P22
D0
U26
D3
G25
TxPOS4
L3
RLOL6
P23
DGND
V1
DGND
G26
TxCLK4
L4
RxNEG/LCV6
P24
PCLK
V2
CLKOUT7
H1
DGND
L5
RxPOS6
P25
DVDD
V3
DVDD
H2
DVDD
L22
RxPOS4
P26
INT
V4
RxCLK9
H3
TxNEG6
L23
RxNEG/LCV4
R1
E3Clk
V5
DGND
H4
TxNEG8
L24
RLOL4
R2
DGND
V22
DGND
H5
TxCLK8
L25
AGND
R3
AGND
V23
RxCLK3
H22
TxCLK2
L26
Addr5
R4
AVDD
V24
DVDD
H23
TxNEG2
M1
DMO4
R5
SFM_EN
V25
CLKOUT5
H24
TxNEG4
M2
DMO6
R22
D7
V26
DGND
H25
DVDD
M3
DMO7
R23
D6
W1
DVDD
H26
DGND
M4
DMO8
R24
D5
W2
RLOL7
J1
DMO11
M5
DMO9
R25
D4
W3
CLKOUT9
J2
CLKOUT6
M22
Addr1
R26
D1
W4
TxNEG9
J3
RLOS6
M23
Addr2
T1
DS3Clk
W5
CLKOUT11
J4
RxCLK8
M24
Addr3
T2
AGND
W22
CLKOUT1
J5
TxPOS8
M25
AVDD
T3
RxNEG/LCV7
W23
TxNEG3
J22
TxPOS2
M26
Addr6
T4
RxCLK7
W24
CLKOUT3
J23
RxCLK2
N1
DMO3
T5
RxPOS7
W25
RLOL5
J24
RLOS4
N2
RESET
T22
RxPOS5
W26
DVDD
15
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
PIN
PIN NAME
PIN
PIN NAME
PIN
PIN NAME
PIN
PIN NAME
Y1
TxNEG7
AB15
RVDD5
AC23
MRing1
AE5
RTip11
Y2
DGND
AB16
MRing5
AC24
DGND
AE6
TGND9
Y3
RxPOS9
AB17
AGND
AC25
RxCLK1
AE7
TRing9
Y4
TxCLK9
AB18
AVDD
AC26
RxNEG/LCV1
AE8
DGND
Y5
DVDD
AB19
MRing3
AD1
RxPOS11
AE9
RTip9
Y22
DVDD
AB20
AGND
AD2
RLOS11
AE10
TVDD7
Y23
TxCLK3
AB21
AVDD
AD3
TTip11
AE11
TRing7
Y24
RxPOS3
AB22
AGND
AD4
MTip11
AE12
AGND
Y25
DGND
AB23
TMS
AD5
RRing11
AE13
AGND
Y26
TxNEG5
AB24
TxPOS1
AD6
DVDD
AE14
RRing5
AA1
TxPOS7
AB25
TxNEG1
AD7
TTip9
AE15
TVDD5
AA2
TxCLK7
AB26
RLOL1
AD8
AGND
AE16
TRing5
AA3
RLOS9
AC1
RxNEG/LCV11
AD9
RRing9
AE17
DGND
AA4
TxPOS9
AC2
RxCLK11
AD10
AGND
AE18
RTip3
AA5
TxCLK11
AC3
DGND
AD11
TTip7
AE19
TVDD3
AA22
TxCLK1
AC4
MRing11
AD12
DVDD
AE20
TRing3
AA23
TxPOS3
AC5
RVDD11
AD13
RRing7
AE21
DGND
AA24
RLOS3
AC6
DGND
AD14
DVDD
AE22
RTip1
AA25
TxCLK5
AC7
DGND
AD15
AGND
AE23
TVDD1
AA26
TxPOS5
AC8
MRing9
AD16
TTip5
AE24
TTip1
AB1
RLOL11
AC9
RGND9
AD17
AGND
AE25
TRST
AB2
TxNEG11
AC10
MRing7
AD18
RRing3
AE26
AGND
AB3
TxPOS11
AC11
DGND
AD19
AGND
AF1
AGND
AB4
TDI
AC12
DGND
AD20
TTip3
AF2
AGND
AB5
TCK
AC13
RTip7
AD21
AGND
AF3
DVDD
AB6
AVDD
AC14
DGND
AD22
RRing1
AF4
TGND11
AB7
AGND
AC15
MTip5
AD23
MTip1
AF5
RGND11
AB8
MTip9
AC16
DGND
AD24
TRing1
AF6
TVDD9
AB9
AVDD
AC17
AGND
AD25
RLOS1
AF7
DVDD
AB10
AGND
AC18
RVDD3
AD26
RxPOS1
AF8
DVDD
AB11
MTip7
AC19
MTip3
AE1
AGND
AF9
RVDD9
AB12
RVDD7
AC20
DGND
AE2
TDO
AF10
TGND7
AB13
RGND7
AC21
AGND
AE3
TRing11
AF11
DVDD
AB14
RGND5
AC22
RVDD1
AE4
TVDD11
AF12
AVDD
16
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
PIN
PIN NAME
AF13
AVDD
AF14
RTip5
AF15
TGND5
AF16
DVDD
AF17
DVDD
AF18
RGND3
AF19
TGND3
AF20
DVDD
AF21
DVDD
AF22
RGND1
AF23
TGND1
AF24
DVDD
AF25
AGND
AF26
AGND
17
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FUNCTIONAL DESCRIPTION
The XRT75R12D is a twelve channel fully integrated Line Interface Unit featuring EXAR’s R3 Technology
(Reconfigurable, Relayless Redundancy) for E3/DS3/STS-1 applications.
The LIU incorporates 12
independent Receivers, Transmitters and Jitter Attenuators in a single 420 Lead TBGA package. Each
channel can be independently programmed to support E3, DS-3 or STS-1 line rates using one input clock
reference of 12.288MHz in Single Frequency Mode (SFM). The LIU is responsible for providing the physical
connection between a line interface and an aggregate mapper or framing device. Along with the analog-todigital processing, the LIU offers monitoring and diagnostic features to help optimize network design
implementation. A key characteristic within the network topology is Automatic Protection Switching (APS).
EXAR’s proven expertise in providing redundany solutions has paved the way for R3 Technology.
1.0 R3 TECHNOLOGY (RECONFIGURABLE, RELAYLESS REDUNDANCY)
Redundancy is used to introduce reliability and protection into network card design. The redundant card in
many cases is an exact replicate of the primary card, such that when a failure occurs the network processor
can automatically switch to the backup card. EXAR’s R3 technology has re-defined E3/DS-3/STS-1 LIU design
for 1:1 and 1+1 redundancy applications. Without relays and one Bill of Materials, EXAR offers multi-port,
integrated LIU solutions to assist high density aggregate applications and framing requirements with reliability.
The following section can be used as a reference for implementing R3 Technology with EXAR’s world leading
line interface units.
1.1
Network Architecture
A common network design that supports 1:1 or 1+1 redundancy consists of N primary cards along with N
backup cards that connect into a mid-plane or back-plane architecture without transformers installed on the
network cards. In addition to the network cards, the design has a line interface card with one source of
transformers, connectors, and protection components that are common to both network cards. With this
design, the bill of materials is reduced to the fewest amount of components. See Figure 2. for a simplified
block diagram of a typical redundancy design.
FIGURE 2. NETWORK REDUNDANCY ARCHITECTURE
GND
37.5Ω
Rx
Framer/
Mapper
0.01µF
LIU
31.6Ω
Tx
31.6Ω
1:1
Line Interface Card
Primary Line Card
0.01µF
Rx
Framer/
Mapper
37.5Ω
1:1
0.01µF
0.01µF
LIU
31.6Ω
Tx
31.6Ω
Redundant Line Card
Back
Plane
or
Mid
Plane
18
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
2.0 CLOCK SYNTHESIZER
The LIU uses a flexible user interface for accepting clock references to generate the internal master clocks
used to drive the LIU. The reference clock used to supply the microprocessor timing is generated from the DS3 or SFM clock input. Therefore, if the chip is configured for STS-1 only or E3 only, then the DS-3 input pin
must be connected to the STS-1 pin or E3 pin respectively. In DS-3 mode or when SFM is used, the STS-1
and E3 input pins can be left unconnected. If SFM is enabled by pulling the SFM_EN pin "High", 12.288MHz is
the only clock reference necessary to generate DS-3, E3, or STS-1 line rates and the microprocessor timing.
A simplified block diagram of the clock synthesizer is shown in Figure 3. Reference clock performance
specifications can be found on Table 2 below.
FIGURE 3. SIMPLIFIED BLOCK DIAGRAM OF THE INPUT CLOCK CIRCUITRY DRIVING THE MICROPROCESSOR
SFM_EN
STS-1Clk/12M
DS3Clk
E3Clk
CLKOUT_n
Clock Synthesizer
LOL_n
0
µProcessor
1
TABLE 2: REFERENCE CLOCK PERFORMANCE SPECIFICATIONS
SYMBOL
REFDUTY
PARAMETER
MIN
TYP
MAX
UNITS
Reference Clock Duty Cycle
40
60
%
REFE3
E3 Reference Clock Frequency Tolerance1
-20
+20
ppm
REFDS3
DS3 Reference Clock Frequency Tolerance1
-20
+20
ppm
REFSTS1
STS-1 Reference Clock Frequency Tolerance1
-20
+20
ppm
REFSFM
SFM Reference Clock Frequency Tolerance1
-20
+20
ppm
tRISE_REFCLK Reference Clock Rise Time (10% to 90%)
5
ns
tFALL_REFCLK Reference Clock Fall Time (90% to 10%)
5
ns
0.005
UIp2p
CLKJIT
Reference Clock Jitter Stability2
NOTES:
1.
Required to meet Bellcore GR-499 specification on frequency stability requirements. However, the LIU can
functionally operate with ±100 ppm without meeting the required specifications.
2.
Reference clock jitter limits are required for the transmit output to meet ITU-T and Bellcore system level jitter
requirements.
19
XRT75R12D
REV. 1.0.1
2.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Clock Distribution
Network cards that are designed to support multiple line rates which are not configured for single frequency
mode should ensure that a clock is applied to the DS3Clk input pin. For example: If the network card being
supplied to an ISP requires E3 only, the DS-3 input clock reference is still necessary to provide read and write
access to the internal microprocessor. Therefore, the E3 mode requires two input clock references. If
however, multiple line rates will not be supported, i.e. E3 only, then the DS3Clk input pin may be hard wire
connected to the E3Clk input pin.
FIGURE 4. CLOCK DISTRIBUTION CONGIFURED IN E3 MODE WITHOUT USING SFM
DS3Clk
E3Clk
Clock Synthesizer
CLKOUT_n
LOL_n
µProcessor
NOTE: For one input clock reference, the single frequency mode should be used.
20
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
3.0 THE RECEIVER SECTION
The receiver is designed so that the LIU can recover clock and data from an attenuated line signal caused by
cable loss or flat loss according to industry specifications. Once data is recovered, it is processed and
presented at the receiver outputs according to the format chosen to interface with a Framer/Mapper or ASIC.
This section describes the detailed operation of various blocks within the receive path. A simplified block
diagram of the receive path is shown in Figure 5.
FIGURE 5. RECEIVE PATH BLOCK DIAGRAM
Peak Detector
RTIP_n
RRing_n
AGC/
Equalizer
Clock & Data
Recovery
Slicer
Jitter
Attenuator
HDB3/
B3ZS
Decoder
MUX
LOS
Detector
RxClk_n
RxPOS_n
RxNEG/LCV_n
RLOS_n
Channel n
3.1
Receive Line Interface
Physical Layer devices are AC coupled to a line interface through a 1:1 transformer. The transformer provides
isolation and a level shift by blocking the DC offset of the incoming data stream. The typical medium for the
line interface is a 75Ω coxial cable. Whether using E3, DS-3 or STS-1, the LIU requires the same bill of
materials, see Figure 6.
FIGURE 6. RECEIVE LINE INTERFACECONNECTION
1:1
RTIP_n
75Ω
Receiver
RRing_n
DS-3/E3/STS-1
37.5Ω
37.5Ω
0.01µF
RLOS_n
3.2
Adaptive Gain Control (AGC)
The Adaptive Gain Control circuit amplifies the incoming analog signal and compensates for the various flat
losses and also for the loss at one-half symbol rate. The AGC has a dynamic range of 30 dB. The peak
detector provides feedback to the equalizer before slicing occurs.
21
XRT75R12D
REV. 1.0.1
3.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Receive Equalizer
The Equalizer restores the integrity of the signal and compensates for the frequency dependent attenuation of
up to 900 feet of coaxial cable (1300 feet for E3). The Equalizer also boosts the high frequency content of the
signal to reduce Inter-Symbol Interference (ISI) so that the slicer slices the signal at 50% of peak voltage to
generate Positive and Negative data. The equalizer can be disabled by programming the appropriate register.
FIGURE 7. ACG/EQUALIZER BLOCK DIAGRAM
Peak Detector
RTIP_n
RRing_n
AGC/
Equalizer
Slicer
LOS
Detector
3.3.1
Recommendations for Equalizer Settings
The Equalizer has two gain settings to provide optimum equalization. In the case of normally shaped DS3/
STS-1 pulses (pulses that meet the template requirements) that has been driven through 0 to 900 feet of cable,
the Equalizer can be enabled. However, for square-shaped pulses such as E3 or for DS3/STS-1 high pulses
(that does not meet the pulse template requirements), it is recommended that the Equalizer be disabled for
cable length less than 300 feet. This would help to prevent over-equalization of the signal and thus optimize
the performance in terms of better jitter transfer characteristics. The Equalizer also contains an additional 20
dB gain stage to provide the line monitoring capability (Receive Monitor Mode) of the resistively attenuated
signals which may have 20dB flat loss. The equalizer and the equalizer gain mode can be enabled by
programming the appropriate register. However, enabling the equalizer gain mode (Receive Monitor Mode)
suppresses the internal LOS circuitry and LOS will never assert nor LOS be declared when operating with
Receive Monitor Mode enabled.
NOTE: The results of extensive testing indicate that even when the Equalizer was enabled, regardless of the cable length,
the integrity of the E3 signal was restored properly over 0 to 12 dB cable loss at Industrial Temperature.
3.4
Clock and Data Recovery
The Clock and Data Recovery Circuit extracts the embedded clock, RxClk_n from the sliced digital data stream
and provides the retimed data to the B3ZS (HDB3) decoder. The Clock Recovery PLL can be in one of the
following two modes:
3.4.1
Data/Clock Recovery Mode
In the presence of input line signals on the RTIP_n and RRing_n input pins and when the frequency difference
between the recovered clock signal and the reference clock signal is less than 0.5%, the clock that is output on
the RxClk_n out pins is the Recovered Clock signal.
3.4.2
Training Mode
In the absence of input signals at RTIP_n and RRing_n pins, or when the frequency difference between the
recovered line clock signal and the reference clock applied on the ExClk_n input pins exceed 0.5%, a Loss of
Lock condition is declared by toggling RLOL_n output pin “High” or setting the RLOL_n bit to “1” in the control
register. Also, the clock output on the RxClk_n pins are the same as the reference channel clock.
22
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
3.5
LOS (Loss of Signal) Detector
3.5.1
DS3/STS-1 LOS Condition
A Digital Loss of SIgnal (DLOS) condition occurs when a string of 175 ± 75 consecutive zeros occur on the line.
When the DLOS condition occurs, the DLOS_n bit is set to “1” in the status control register. DLOS condition is
cleared when the detected average pulse density is greater than 33% for 175 ± 75 pulses. Analog Loss of
Signal (ALOS) condition occurs when the amplitude of the incoming line signal is below the threshold as shown
in the Table 3.The status of the ALOS condition is reflected in the ALOS_n status control register. RLOS is the
logical OR of the DLOS and ALOS states. When the RLOS condition occurs the RLOS_n output pin is toggled
“High” and the RLOS_n bit is set to “1” in the status control register.
TABLE 3: THE ALOS (ANALOG LOS) DECLARATION AND CLEARANCE THRESHOLDS FOR A GIVEN SETTING OF
REQEN (DS3 AND STS-1 APPLICATIONS)
SIGNAL LEVEL TO DECLARE ALOS
DEFECT
SIGNAL LEVEL TO CLEAR ALOS
DEFECT
0
< 41mVpk
> 102mVpk
1
< 52mVpk
> 117mVpk
0
< 51mVpk
> 114mVpk
1
< 58mVpk
> 133mVpk
APPLICATION REQEN SETTING
DS3
STS-1
3.5.2
Disabling ALOS/DLOS Detection
For debugging purposes it is useful to disable the ALOS and/or DLOS detection. Writing a “1” to both
ALOSDIS_n and DLOSDIS_n bits disables the LOS detection on a per channel basis.
3.5.3
E3 LOS Condition:
If the level of incoming line signal drops below the threshold as described in the ITU-T G.775 standard, the
LOS condition is detected. Loss of signal is defined as no transitions for 10 to 255 consecutive zeros. No
transitions is defined as a signal level between 15 and 35 dB below the normal. This is illustrated in Figure 8.
The LOS condition is cleared within 10 to 255 UI after restoration of the incoming line signal. Figure 9 shows
the LOS declaration and clearance conditions.
FIGURE 8. LOSS OF SIGNAL DEFINITION FOR E3 AS PER ITU-T G.775
0 dB
Maximum Cable Loss for E3
LOS Signal Must be Cleared
-12 dB
-15dB
LOS Signal may be Cleared or Declared
-35dB
LOS Signal Must be Declared
23
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 9. LOSS OF SIGNAL DEFINITION FOR E3 AS PER ITU-T G.775.
Actual Occurrence
of LOS Condition
Line Signal
is Restored
RTIP/
RRing
10 UI
255 UI
Time Range for
LOS Declaration
10 UI
255 UI
RLOS Output Pin
0 UI
0 UI
G.775
Compliance
3.5.4
Time Range for
LOS Clearance
G.775
Compliance
Interference Tolerance
For E3 mode, ITU-T G.703 Recommendation specifies that the receiver be able to recover error free clock and
data in the presence of a sinusoidal interfering tone signal. For DS3 and STS-1 modes, the same
recommendation is being used. Figure 10 shows the configuration to test the interference margin for DS3/
STS1. Figure 11 shows the set up for E3.
FIGURE 10. INTERFERENCE MARGIN TEST SET UP FOR DS3/STS-1
Attenuator
N
Sine Wave
Generator
DS3 = 22.368 MHz
STS-1 = 25.92 MHz
DUT
XRT75R12D
∑
Test
Equipment
Cable Simulator
Pattern Generator
2 23 -1 PRBS
S
FIGURE 11. INTERFERENCE MARGIN TEST SET UP FOR E3.
Attenuator 1
Sine Wave
Generator
17.184mHz
Attenuator 2
N
∑
DUT
XRT75R12D
Test
Equipment
Signal Source
223-1 PRBS
Cable Simulator
S
24
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 4: INTERFERENCE MARGIN TEST RESULTS
MODE
CABLE LENGTH (ATTENUATION)
INTERFERENCE TOLERANCE
Equalizer “IN”
E3
DS3
STS-1
-17 dB
0 dB
12 dB
-14 dB
0 feet
-15 dB
225 feet
-15 dB
450 feet
-14 dB
0 feet
-15 dB
225 feet
-14 dB
450 feet
-14 dB
25
XRT75R12D
REV. 1.0.1
3.5.5
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Muting the Recovered Data with LOS condition:
When the LOS condition is declared, the clock recovery circuit locks into the reference clock applied to the
internal master clock outputs this clock onto the RxClk_n output pin. The data on the RxPOS_n and RxNEG_n
pins can be forced to zero by setting the LOSMUT_n bits in the individual channel control register to “1”.
NOTE: When the LOS condition is cleared, the recovered data is output on RxPOS_n and RxNEG_n pins.
FIGURE 12. RECEIVER DATA OUTPUT AND CODE VIOLATION TIMING
tRRX
tFRX
RxClk
tLCVO
LCV
tCO
RPOS or
RNEG
SYMBOL
RxClk
PARAMETER
Duty Cycle
MIN
TYP
MAX
UNITS
45
50
55
%
RxClk Frequency
E3
34.368
MHz
DS-3
44.736
MHz
STS-1
51.84
MHz
tRRX
RxClk rise time (10% o 90%)
2
4
ns
tFRX
RxClk falling time (10% to 90%)
2
4
ns
tCO
RxClk to RPOS/RNEG delay time
4
ns
tLCVO
3.6
RxClk to rising edge of LCV output delay
2.5
ns
B3ZS/HDB3 Decoder
The decoder block takes the output from the clock and data recovery block and decodes the B3ZS (for DS3 or
STS-1) or HDB3 (for E3) encoded line signal and detects any coding errors or excessive zeros in the data
stream. Whenever the input signal violates the B3ZS or HDB3 coding sequence for bipolar violation or
contains three (for B3ZS) or four (for HDB3) or more consecutive zeros, an active “High” pulse is generated on
the RLCV_n output pins to indicate line code violation.
26
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
4.0 THE TRANSMITTER SECTION
The transmitter is designed so that the LIU can accept serial data from a local device, encode the data
properly, and then output an analog pulse according to the pulse shape chosen in the appropriate registers.
This section describes the detailed operation of various blocks within the transmit path. A simplified block
diagram of the transmit path is shown in Figure 13.
FIGURE 13. TRANSMIT PATH BLOCK DIAGRAM
TTIP_n
TRing_n
MTIP_n
MRing_n
Line
Driver
Device
Monitor
Tx
Pulse
Shaping
Jitter
Attenuator
Timing
Control
MUX
HDB3/
B3ZS
Encoder
Tx
Control
TxClk_n
TxPOS_n
TxNEG_n
TxON
DMO_n
Channel n
Transmit Digital Input Interface
The method for applying data to the transmit inputs of the LIU is a serial interface consisting of TxClk, TxPOS,
and TxNEG. For single rail mode, only TxClk and TxPOS are necessary for providing the local data from a
Framer device or ASIC. Data can be sampled on either edge of the input clock signal by programming the
appropriate register. A typical interface is shown in Figure 14.
FIGURE 14. TYPICAL INTERFACE BETWEEN TERMINAL EQUIPMENT AND THE XRT75R12D (DUAL-RAIL DATA)
Terminal
Equipment
(E3/DS3 or STS-1
Framer)
TxPOS
TPData
TxNEG
TNData
TxLineClk
TxClk
Transmit
Logic
Block
Exar E3/DS3/STS-1 LIU
27
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 15. TRANSMITTER TERMINAL INPUT TIMING
tRTX
tFTX
TxClk
tTSU
tTHO
TPData or
TNData
TTIP or
TRing
SYMBOL
TxClk
PARAMETER
Duty Cycle
MIN
TYP
MAX
UNITS
30
50
70
%
TxClk Frequency
E3
34.368
MHz
DS-3
44.736
MHz
STS-1
51.84
MHz
tRTX
TxClk Rise Time (10% to 90%)
4
ns
tFTX
TxClk Fall Time (10% to 90%)
4
ns
tTSU
TPData/TNData to TxClk falling set up time
3
ns
tTHO
TPData/TNData to TxClk falling hold time
3
ns
FIGURE 16. SINGLE-RAIL OR NRZ DATA FORMAT (ENCODER AND DECODER ARE ENABLED)
Data
1
1
TPData
TxClk
28
0
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 17. DUAL-RAIL DATA FORMAT (ENCODER AND DECODER ARE DISABLED)
Data
1
1
0
TPData
TNData
TxClk
4.1
Transmit Clock
The Transmit Clock applied via TxClk_n pins, for the selected data rate (for E3 = 34.368 MHz, DS3 = 44.736
MHz or STS-1 = 51.84 MHz), is duty cycle corrected by the internal PLL circuit to provide a 50% duty cycle
clock to the pulse shaping circuit. This allows a 30% to 70% duty cycle Transmit Clock to be supplied.
4.2
B3ZS/HDB3 ENCODER
When the Single-Rail (NRZ) data format is selected, the Encoder Block encodes the data into either B3ZS
format (for either DS3 or STS-1) or HDB3 format (for E3).
4.2.1
B3ZS Encoding
An example of B3ZS encoding is shown in Figure 18. If the encoder detects an occurrence of three
consecutive zeros in the data stream, it is replaced with either B0V or 00V, where ‘B’ refers to Bipolar pulse
that is compliant with the Alternating polarity requirement of the AMI (Alternate Mark Inversion) line code and
‘V’ refers to a Bipolar Violation (e.g., a bipolar pulse that violates the AMI line code). The substitution of B0V or
00V is made so that an odd number of bipolar pulses exist between any two consecutive violation (V) pulses.
This avoids the introduction of a DC component into the line signal.
FIGURE 18. B3ZS ENCODING FORMAT
TClk
4.2.2
TPDATA
1
0
Line
Signal
1
0
1 1
1
0
0
0
0
0
0
V
0
1
1
1
0
0
0
0
0
V
0
0
0
B
0
V
0
B
0
0
V
HDB3 Encoding
An example of the HDB3 encoding is shown in Figure 19. If the HDB3 encoder detects an occurrence of four
consecutive zeros in the data stream, then the four zeros are substituted with either 000V or B00V pattern. The
substitution code is made in such a way that an odd number of pulses exist between any consecutive V pulses.
This avoids the introduction of DC component into the analog signal.
29
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 19. HDB3 ENCODING FORMAT
TClk
4.3
TPDATA
1
0
Line
Signal
1
0
1 1
1
0
0
0
0
0
0
0
V
1
1
0
0
0
0
0
0
1
0
0
0
0
0
B
0
0
V
V
TRANSMIT PULSE SHAPER
The Transmit Pulse Shaper converts the B3ZS encoded digital pulses into a single analog Alternate Mark
Inversion (AMI) pulse that meets the industry standard mask template requirements for STS-1 and DS3. For
E3 mode, the pulse shaper converts the HDB3 encoded pulses into a single full amplitude square shaped
pulse with very little slope. The Pulse Shaper Block also includes a Transmit Build Out Circuit, which can
either be disabled or enabled by setting the TxLEV_n bit to “1” or “0” in the control register. For DS3/STS-1
rates, the Transmit Build Out Circuit is used to shape the transmit waveform that ensures that transmit pulse
template requirements are met at the Cross-Connect system. The distance between the transmitter output and
the Cross-Connect system can be between 0 to 450 feet. For E3 rate, since the output pulse template is
measured at the secondary of the transformer and since there is no Cross-Connect system pulse template
requirements, the Transmit Build Out Circuit is always disabled. The differential line driver increases the
transmit waveform to appropriate level and drives into the 75Ω load as shown in Figure 20.
FIGURE 20. TRANSMIT PULSE SHAPE TEST CIRCUIT
R1
TxPOS(n)
TxNEG(n)
TxLineClk(n)
TTIP(n)
TPData(n)
TNData(n)
TxClk(n)
TRing(n)
31.6Ω +1%
31.6Ω + 1%
4.3.1
R3
75Ω
R2
1:1
Guidelines for using Transmit Build Out Circuit
If the distance between the transmitter and the DSX3 or STSX-1, Cross-Connect system, is less than 225 feet,
enable the Transmit Build Out Circuit by setting the TxLEV_n control bit to “0”. If the distance between the
transmitter and the DSX3 or STSX-1 is greater than 225 feet, disable the Transmit Build Out Circuit.
30
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
4.4
E3 line side parameters
The XRT75R12D line output at the transformer output meets the pulse shape specified in ITU-T G.703 for
34.368 Mbits/s operation. The pulse mask as specified in ITU-T G.703 for 34.368 Mbits/s is shown in Figure
21.
FIGURE 21. PULSE MASK FOR E3 (34.368 MBITS/S) INTERFACE AS PER ITU-T G.703
17 ns
(14.55 + 2.45)
8.65 ns
V = 100%
N om inal P ulse
50%
14.55ns
12.1ns
(14.55 - 2.45)
10%
0%
10%
20%
TABLE 5: E3 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS
PARAMETER
MIN
TYP
MAX
UNITS
0.90
1.00
1.10
Vpk
Transmit Output Pulse Amplitude Ratio
0.95
1.00
1.05
Transmit Output Pulse Width
12.5
14.55
16.5
ns
0.02
0.05
UIPP
TRANSMITTER LINE SIDE OUTPUT CHARACTERISTICS
Transmit Output Pulse Amplitude
(Measured at secondary of the transformer)
Transmit Intrinsic Jitter
RECEIVER LINE SIDE INPUT CHARACTERISTICS
Receiver Sensitivity (length of cable)
900
1200
feet
Interference Margin
-20
-14
dB
Jitter Tolerance @ Jitter Frequency 800KHz
0.15
0.28
UIPP
Signal level to Declare Loss of Signal
-35
Signal Level to Clear Loss of Signal
-15
31
dB
dB
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 5: E3 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS
PARAMETER
MIN
TYP
MAX
UNITS
Occurence of LOS to LOS Declaration Time
10
255
UI
Termination of LOS to LOS Clearance Time
10
255
UI
NOTE: The above values are at TA = 250C and VDD = 3.3 V± 5%.
FIGURE 22. BELLCORE GR-253 CORE TRANSMIT OUTPUT PULSE TEMPLATE FOR SONET STS-1 APPLICATIONS
ST S-1 Pulse T emplate
1.2
1
Norm a liz e d Am plitude
0.8
0.6
Lower Curve
Upper Curve
0.4
0.2
0
2
3
4
1.
1.
1.
1
9
0.
1
8
0.
1.
6
0.
7
5
0.
0.
4
0.
0.
2
3
0.
0
1
0.
.1
-0
.3
.4
.2
-0
-0
.6
.7
.5
-0
-0
-0
-0
.9
.8
-0
-0
-1
-0.2
Time, in UI
TABLE 6: STS-1 PULSE MASK EQUATIONS
TIME IN UNIT INTERVALS
NORMALIZED AMPLITUDE
LOWER CURVE
- 0.03
-0.85 < T < -0.38
-0.38
·
< T < 0.36
⎧π
T ⎫
0.5 1 + sin ⎨ --- ⎛ 1 + ----------- ⎞ ⎬ – 0.03
⎝
0.18 ⎠ ⎭
⎩2
- 0.03
0.36 < T < 1.4
UPPER CURVE
0.03
-0.85 < T < -0.68
32
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 6: STS-1 PULSE MASK EQUATIONS
TIME IN UNIT INTERVALS
NORMALIZED AMPLITUDE
·
-0.68 < T < 0.26
⎧π
T ⎫
0.5 1 + sin ⎨ --- ⎛ 1 + ----------- ⎞ ⎬ + 0.03
⎝
0.34 ⎠ ⎭
⎩2
0.1 + 0.61 x e-2.4[T-0.26]
0.26 < T < 1.4
TABLE 7: STS-1 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS (GR-253)
PARAMETER
MIN
TYP
MAX
UNITS
0.65
0.75
0.90
Vpk
0.90
1.00
1.10
Vpk
Transmit Output Pulse Width
8.6
9.65
10.6
ns
Transmit Output Pulse Amplitude Ratio
0.90
1.00
1.10
0.02
0.05
TRANSMITTER LINE SIDE OUTPUT CHARACTERISTICS
Transmit Output Pulse Amplitude
(measured with TxLEV = 0)
Transmit Output Pulse Amplitude
(measured with TxLEV = 1)
Transmit Intrinsic Jitter
UIpp
RECEIVER LINE SIDE INPUT CHARACTERISTICS
Receiver Sensitivity (length of cable)
900
Jitter Tolerance @ Jitter Frequency 400 KHz
0.15
1100
UIpp
Signal Level to Declare Loss of Signal
Refer to Table 3
Signal Level to Clear Loss of Signal
Refer to Table 3
NOTE: The above values are at TA = 250C and VDD = 3.3 V ± 5%.
33
feet
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 23. TRANSMIT OUPUT PULSE TEMPLATE FOR DS3 AS PER BELLCORE GR-499
D S3 Pulse T em plate
1.2
1
0.6
Lower Curve
Upper Curve
0.4
0.2
0
3
4
1.
2
1.
1.
1
1
9
0.
1.
7
8
6
0.
5
0.
0.
0.
3
4
0.
2
0.
0.
0
1
0.
.2
.3
.4
.5
.6
.7
.8
.1
-0
-0
-0
-0
-0
-0
-0
-0
-0
.9
-0.2
-1
Norm a lize d Am plitude
0.8
Tim e , in UI
TABLE 8: DS3 PULSE MASK EQUATIONS
TIME IN UNIT INTERVALS
NORMALIZED AMPLITUDE
LOWER CURVE
- 0.03
-0.85 < T < -0.36
-0.36
·
< T < 0.36
⎧π
T ⎫
0.5 1 + sin ⎨ --- ⎛ 1 + ----------- ⎞ ⎬ – 0.03
⎝
0.18 ⎠ ⎭
⎩2
- 0.03
0.36 < T < 1.4
UPPER CURVE
0.03
-0.85 < T < -0.68
·
-0.68 < T < 0.36
⎧π
T ⎫
0.5 1 + sin ⎨ --- ⎛ 1 + ----------- ⎞ ⎬ + 0.03
⎝
⎠
2
0.34
⎩
⎭
0.08 + 0.407 x e-1.84[T-0.36]
0.36 < T < 1.4
34
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 9: DS3 TRANSMITTER LINE SIDE OUTPUT AND RECEIVER LINE SIDE INPUT SPECIFICATIONS (GR-499)
PARAMETER
MIN
TYP
MAX
UNITS
0.65
0.75
0.85
Vpk
0.90
1.00
1.10
Vpk
Transmit Output Pulse Width
10.10
11.18
12.28
ns
Transmit Output Pulse Amplitude Ratio
0.90
1.00
1.10
0.02
0.05
TRANSMITTER LINE SIDE OUTPUT CHARACTERISTICS
Transmit Output Pulse Amplitude
(measured with TxLEV = 0)
Transmit Output Pulse Amplitude
(measured with TxLEV = 1)
Transmit Intrinsic Jitter
UIpp
RECEIVER LINE SIDE INPUT CHARACTERISTICS
Receiver Sensitivity (length of cable)
900
Jitter Tolerance @ 400 KHz (Cat II)
0.15
1100
UIpp
Signal Level to Declare Loss of Signal
Refer to Table 3
Signal Level to Clear Loss of Signal
Refer to Table 3
NOTE: The above values are at TA = 250C and VDD = 3.3V ± 5%.
35
feet
XRT75R12D
REV. 1.0.1
4.5
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Transmit Drive Monitor
This feature is used for monitoring the transmit line for occurrence of fault conditions such as a short circuit on
the line or a defective line driver. To activate this function, connect MTIP_n pins to the TTIP_n lines via a 270Ω
resistor and MRing_n pins to TRing_n lines via 270Ω resistor as shown in Figure 24.
FIGURE 24. TRANSMIT DRIVER MONITOR SET-UP.
R1
TTIP(n)
31.6Ω +1%
R3
75Ω
R2
TxPOS(n)
TxNEG(n)
TxLineClk(n)
TRing(n)
TPData(n)
TNData(n)
TxClk(n)
31.6Ω + 1%
1:1
R1
MTIP(n)
270Ω
R2
MRing(n)
270Ω
When the MTIP_n and MRing_n are connected to the TTIP_n and TRing_n lines, the drive monitor circuit
monitors the line for transitions. The DMO_n (Drive Monitor Output) will be asserted “Low” as long as the
transitions on the line are detected via MTIP_n and MRing_n. If no transitions on the line are detected for 128
± 32 TxClk_n periods, the DMO_n output toggles “High” and when the transitions are detected again, DMO_n
toggles “Low”.
NOTE: The Drive Monitor Circuit is only for diagnostic purpose and does not have to be used to operate the transmitter.
4.6
Transmitter Section On/Off
The transmitter section of each channel can either be turned on or off. To turn on the transmitter, set the input
pin TxON to “High” and write a “1” to the TxON_n control bit. When the transmitter is turned off, TTIP_n and
TRing_n are tri-stated.
NOTES:
1.
This feature provides support for Redundancy.
2.
If the XRT75R12D is configured in Host mode, to permit a system designed for redundancy to quickly shut-off the
defective line card and turn on the back-up line card, writing a “1” to the TxON_n control bits transfers the control
to TxON pin.
36
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
5.0 JITTER
There are three fundamental parameters that describe circuit performance relative to jitter
• Jitter Tolerance
• Jitter Transfer
• Jitter Generation
5.1
JITTER TOLERANCE
Jitter tolerance is a measure of how well a Clock and Data Recovery unit can successfully recover data in the
presence of various forms of jitter. It is characterized by the amount of jitter required to produce a specified bit
error rate. The tolerance depends on the frequency content of the jitter. Jitter Tolerance is measured as the
jitter amplitude over a jitter spectrum for which the clock and data recovery unit achieves a specified bit error
rate (BER). To measure the jitter tolerance as shown in Figure 25, jitter is introduced by the sinusoidal
modulation of the serial data bit sequence. Input jitter tolerance requirements are specified in terms of
compliance with jitter mask which is represented as a combination of points. Each point corresponds to a
minimum amplitude of sinusoidal jitter at a given jitter frequency.
FIGURE 25. JITTER TOLERANCE MEASUREMENTS
Pattern
Generator
Data
Error
Detector
DUT
XRT75R12D
Clock
Modulation
Freq.
FREQ
Synthesizer
5.1.1
DS3/STS-1 Jitter Tolerance Requirements
Bellcore GR-499 CORE specifies the minimum requirement of jitter tolerance for Category I and Category II.
The jitter tolerance requirement for Category II is the most stringent. Figure 26 shows the jitter tolerance curve
as per GR-499 specification.
37
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
JITTER AMPLITUDE (UIpp)
FIGURE 26. INPUT JITTER TOLERANCE FOR DS3/STS-1
64
GR-253 STS-1
41
15
GR-499 Cat II
GR-499 Cat I
10
XRT75R12D
5
1.5
0.3
0.15
0.1
0.01
0.03
0.3
2
20
100
JITTER FREQUENCY (kHz)
5.1.2
E3 Jitter Tolerance Requirements
ITU-T G.823 standard specifies that the clock and data recovery unit must be able to tolerate jitter up to certain
specified limits. Figure 27 shows the tolerance curve.
FIGURE 27. INPUT JITTER TOLERANCE FOR E3
ITU-T G.823
JITTER AMPLITUDE (UIpp)
64
XRT75R12D
10
1.5
0.3
0.1
1
10
800
JITTER FREQUENCY (kHz)
As shown in the Figures above, in the jitter tolerance measurement, the dark line indicates the minimum level
of jitter that the E3/DS3/STS-1 compliant component must tolerate. Table 10 below shows the jitter amplitude
versus the modulation frequency for various standards.
38
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 10: JITTER AMPLITUDE VERSUS MODULATION FREQUENCY (JITTER TOLERANCE)
INPUT JITTER AMPLITUDE (UI P-P)
BIT RATE
(KB/S)
STANDARD
34368
MODULATION FREQUENCY
A1
A2
A3
F1(HZ)
F2(HZ)
F3(KHZ)
F4(KHZ)
F5(KHZ)
ITU-T G.823
1.5
0.15
-
100
1000
10
800
-
44736
GR-499
CORE Cat I
5
0.1
-
10
2.3k
60
300
-
44736
GR-499
CORE Cat II
10
0.3
-
10
669
22.3
300
-
51840
GR-253
CORE Cat II
15
1.5
0.15
10
30
300
2
20
5.2
JITTER TRANSFER
Jitter Transfer function is defined as the ratio of jitter on the output relative to the jitter applied on the input
versus frequency. There are two distinct characteristics in jitter transfer, jitter gain (jitter peaking) defined as
the highest ratio above 0dB and jitter transfer bandwidth. The overall jitter transfer bandwidth is controlled by a
low bandwidth loop, typically using a voltage-controlled crystal oscillator (VCXO).
The jitter transfer function is a ratio between the jitter output and jitter input for a component, or system often
expressed in dB. A negative dB jitter transfer indicates the element removed jitter. A positive dB jitter transfer
indicates the element added jitter. A zero dB jitter transfer indicates the element had no effect on jitter.
Table 11 shows the jitter transfer characteristics and/or jitter attenuation specifications for various data rates:
TABLE 11: JITTER TRANSFER SPECIFICATION/REFERENCES
E3
DS3
STS-1
ETSI TBR-24
GR-499 CORE section 7.3.2
Category I and Category II
GR-253 CORE section 5.6.2.1
NOTE: The above specifications can be met only with a jitter attenuator that supports E3/DS3/STS-1 rates.
5.3
Jitter Attenuator
An advanced crystal-less jitter attenuator per channel is included in the XRT75R12D. The jitter attenuator
requires no external crystal nor high-frequency reference clock. By clearing or setting the JATx/Rx_n bits in
the channel control registers selects the jitter attenuator either in the Receive or Transmit path on per channel
basis. The FIFO size can be either 16-bit or 32-bit. The bits JA0_n and JA1_n can be set to appropriate
combination to select the different FIFO sizes or to disable the Jitter Attenuator on a per channel basis. Data is
clocked into the FIFO with the associated clock signal (TxClk or RxClk) and clocked out of the FIFO with the
dejittered clock. When the FIFO is within two bits of overflowing or underflowing, the FIFO limit status bit, FL_n
is set to “1” in the Alarm status register. Reading this bit clears the FIFO and resets the bit into default state.
NOTE: It is recommended to select the 16-bit FIFO for delay-sensitive applications as well as for removing smaller amounts
of jitter. Table 12 specifies the jitter transfer mask requirements for various data rates:
39
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 12: JITTER TRANSFER PASS MASKS
RATE
(KBITS)
MASK
F1
(HZ)
F2
(HZ)
F3
(HZ)
F4
(KHZ)
A1(dB)
A2(dB)
34368
G.823
ETSI-TBR-24
100
300
3K
800K
0.5
-19.5
44736
GR-499, Cat I
GR-499, Cat II
GR-253 CORE
10
10
10
10k
56.6k
40
-
15k
300k
15k
0.1
0.1
0.1
-
51840
GR-253 CORE
10
40k
-
400k
0.1
-
The jitter attenuator within the XRT75R12D meets the latest jitter attenuation specifications and/or jitter
transfer characteristics as shown in the Figure 28.
JITTER AMPLITUDE
FIGURE 28. JITTER TRANSFER REQUIREMENTS AND JITTER ATTENUATOR PERFORMANCE
A1
A2
F1
F2
F3
F4
J IT T E R F R E Q U E N C Y (k H z )
5.3.1
JITTER GENERATION
Jitter Generation is defined as the process whereby jitter appears at the output port of the digital equipment in
the absence of applied input jitter. Jitter Generation is measured by sending jitter free data to the clock and
data recovery circuit and measuring the amount of jitter on the output clock or the re-timed data. Since this is
essentially a noise measurement, it requires a definition of bandwidth to be meaningful. The bandwidth is set
according to the data rate. In general, the jitter is measured over a band of frequencies.
40
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
6.0 DIAGNOSTIC FEATURES
6.1
PRBS Generator and Detector
The XRT75R12D contains an on-chip Pseudo Random Binary Sequence (PRBS) generator and detector for
diagnostic purpose. With the PRBSEN_n bit = “1”, the transmitter will send out PRBS of 223-1 in E3 rate or
215-1 in STS-1/DS3 rate. At the same time, the receiver PRBS detector is also enabled. When the correct
PRBS pattern is detected by the receiver, the RNEG/LCV pin will go “Low” to indicate PRBS synchronization
has been achieved. When the PRBS detector is not in sync the PRBSLS bit will be set to “1” and RNEG/LCV
pin will go “High”.
With the PRBS mode enabled, the user can also insert a single bit error by toggling “INSPRBS” bit. This is
done by writing a “1” to INSPRBS bit. The receiver at RNEG/LCV pin will pulse “High” for one RxClk cycle for
every bit error detected. Any subsequent single bit error insertion must be done by first writing a “0” to
INSPRBS bit and followed by a “1”.
Figure 29 shows the status of RNEG/LCV pin when the XRT75R12D is configured in PRBS mode.
NOTE: In PRBS mode, the device is forced to operate in Single-Rail Mode.
FIGURE 29. PRBS MODE
RxClk
SYNC LOSS
RxNEG/LCV
PRBS SYNC
Single Bit Error
41
XRT75R12D
REV. 1.0.1
6.2
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
LOOPBACKS
The XRT75R12D offers three loopback modes for diagnostic purposes. The loopback modes are selected via
the RLB_n and LLB_n bits n the Channel control registers select the loopback modes.
6.2.1
ANALOG LOOPBACK
In this mode, the transmitter outputs TTIP_n and TRing_n are internally connected to the receiver inputs
RTIP_n and RRing_n as shown in Figure 30. Data and clock are output at RxClk_n, RxPOS_n and RxNEG_n
pins for the corresponding transceiver. Analog loopback exercises most of the functional blocks of the device
including the jitter attenuator which can be selected in either the transmit or receive path.
NOTES:
1.
In the Analog loopback mode, data is also output via TTIP_n and TRing_n pins.
2.
Signals on the RTIP_n and RRing_n pins are ignored during analog loopback.
HDB3/B3ZS
ENCODER
TxNEG
RxClk
RxPOS
RxNEG
HDB3/B3ZS
DECODER
JITTER
ATTENUATOR
TxClk
TxPOS
TIMING
CONTROL
JITTER
ATTENUATOR
FIGURE 30. ANALOG LOOPBACK
DATA &
CLOCK
RECOVERY
42
TTIP
Tx
TRing
RTIP
Rx
RRing
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
6.2.2
DIGITAL LOOPBACK
When the Digital Loopback is selected, the transmit clock TxClk_n and transmit data inputs (TxPOS_n &
TxNEG_n are looped back and output onto the RxClk_n, RxPOS_n and RxNEG_n pins as shown in
Figure 31.
HDB3/B3ZS
ENCODER
TxNEG
RxCLK
RxPOS
HDB3/B3ZS
DECODER
RxNEG
6.2.3
JITTER
ATTENUATOR
TxCLK
TxPOS
TIMING
CONTROL
JITTER
ATTENUATOR
FIGURE 31. DIGITAL LOOPBACK
DATA &
CLOCK
RECOVERY
TTIP
Tx
TRing
RTIP
Rx
RRing
REMOTE LOOPBACK
With Remote loopback activated as shown in Figure 32, the receive data on RTIP and RRing is looped back
after the jitter attenuator (if selected in receive or transmit path) to the transmit path using RxClk as transmit
timing. The receive data is also output via the RxPOS and RxNEG pins.
NOTE: Input signals on TxClk, TxPOS and TxNEG are ignored during Remote loopback.
HDB3/B3ZS
ENCODER
TxNEG
RxCLK
RxPOS
RxNEG
HDB3/B3ZS
DECODER
JITTER
ATTENUATOR
TxCLK
TxPOS
TIMING
CONTROL
JITTER
ATTENUATOR
FIGURE 32. REMOTE LOOPBACK
DATA &
CLOCK
RECOVERY
TTIP
Tx
TRing
43
RTIP
Rx
RRing
XRT75R12D
REV. 1.0.1
6.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TRANSMIT ALL ONES (TAOS)
Transmit All Ones (TAOS) can be set by setting the TAOS_n control bits to “1” in the Channel control registers.
When the TAOS is set, the Transmit Section generates and transmits a continuous AMI all “1’s” pattern on
TTIP_n and TRing_n pins. The frequency of this ones pattern is determined by TxClk_n. the TAOS data path
is shown in Figure 33. TAOS does not operate in Analog loopback or Remote loopback modes, however will
function in Digital loopback mode.
TxCLK
TxPOS
HDB3/B3ZS
ENCODER
TxNEG
JITTER
ATTENUATOR
FIGURE 33. TRANSMIT ALL ONES (TAOS)
TIMING
CONTROL
Tx
TTIP
Transmit All 1's
TRing
RxCLK
RxPOS
RxNEG
HDB3/B3ZS
DECODER
JITTER
ATTENUATOR
TAOS
DATA &
CLOCK
RECOVERY
44
RTIP
Rx
RRing
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
7.0 MICROPROCESSOR INTERFACE BLOCK
The Microprocessor Interface section supports communication between the local microprocessor (µP) and the
LIU. The XRT75R12D supports a parallel interface asynchronously or synchronously timed to the LIU. The
microprocessor interface is selected by the state of the Pmode input pin. Selecting the microprocessor interface mode is shown in Table 13.
TABLE 13: SELECTING THE MICROPROCESSOR INTERFACE MODE
PMODE
MICROPROCESSOR MODE
"Low"
Asynchronous Mode
"High"
Synchronous Mode
The local µP configures the LIU by writing data into specific addressable, on-chip Read/Write registers. The
µP provides the signals which are required for a general purpose microprocessor to read or write data into
these registers. The µP also supports polled and interrupt driven environments. A simplified block diagram of
the microprocessor is shown in Figure 34.
FIGURE 34. SIMPLIFIED BLOCK DIAGRAM OF THE MICROPROCESSOR INTERFACE BLOCK
CS
WR
RD
Addr[7:0]
D[7:0]
PCLK
Microprocessor
Interface
Pmode
RESET
RDY
INT
45
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
7.1 THE MICROPROCESSOR INTERFACE BLOCK SIGNALS
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals. These interface signals are described below in Table 14. The microprocessor interface can be configured to operate in Asynchronous mode
or Synchronous mode.
TABLE 14: XRT75R12D MICROPROCESSOR INTERFACE SIGNALS
PIN NAME
TYPE
DESCRIPTION
Pmode
I
D[7:0]
I/O
Addr[7:0]
I
Eight-Bit Address Bus Inputs
The XRT75R12D LIU microprocessor interface uses a direct address bus. This address bus is
provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT75R12D LIU and
enables Read/Write operations with the on-chip register locations.
RD
I
Read Signal This active low input functions as the read signal from the local µP. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read operation has been
requested and begins the process of the read cycle.
WR
I
Write Signal This active low input functions as the write signal from the local µP. When this
pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write operation has been
requested and begins the process of the write cycle.
RDY
O
Ready Output This active low signal is provided by the LIU device. It indicates that the current read or write cycle is complete, and the LIU is waiting for the next command.
INT
O
Interrupt Output This active low signal is provided by the LIU to alert the local mP that a
change in alarm status has occured. This pin is Reset Upon Read (RUR) once the alarm status registers have been cleared.
RESET
I
Reset Input This active low input pin is used to Reset the LIU.
Microprocessor Interface Mode Select Input pin
This pin is used to specify the microprocessor interface mode.
Bi-Directional Data Bus for register "Read" or "Write" Operations.
46
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
7.2 ASYNCHRONOUS AND SYNCHRONOUS DESCRIPTION
Whether the LIU is configured for Asynchronous or Synchronous mode, the following descriptions apply. The
synchronous mode requires an input clock (PCLK) to be used as the microprocessor timing reference. Read
and Write operations are described below.
Read Cycle (For Pmode = "0" or "1")
Whenever the local µP wishes to read the contents of a register, it should do the following.
1. Place the address of the target register on the address bus input pins Addr[7:0].
2. While the µP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the µP and
the LIU microprocessor interface block.
3. Next, the µP should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action enables the bi-directional data bus output drivers of the LIU.
4. After the µP toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the µP that the data is available to be read by the µP, and that it is ready for the next command.
5. After the µP detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
6. The CS input pin must be pulled "High" before a new command can be issued.
Write Cycle (For Pmode = "0" or "1")
Whenever a local µP wishes to write a byte or word of data into a register within the LIU, it should do the following.
1. Place the address of the target register on the address bus input pins Addr[7:0].
2. While the µP is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the µP and
the LIU microprocessor interface block.
3. The µP should then place the byte or word that it intends to write into the target register, on the bi-directional data bus D[7:0].
4. Next, the µP should indicate that this current bus cycle is a Write operation by toggling the WR input pin
"Low". This action enables the bi-directional data bus input drivers of the LIU.
5. After the µP toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the µP that the data has been written into the internal register location, and that it is ready for the
next command.
6. The CS input pin must be pulled "High" before a new command can be issued.
FIGURE 35. ASYNCHRONOUS µP INTERFACE SIGNALS DURING PROGRAMMED I/O READ AND WRITE OPERATIONS
READ OPERATION
WRITE OPERATION
t0
t0
Addr[7:0]
Valid Address
Valid Address
CS
D[7:0]
Valid Data for Readback
Data Available to Write Into the LIU
t1
RD
t3
WR
t2
t4
RDY
47
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.1
TABLE 15: ASYNCHRONOUS TIMING SPECIFICATIONS
SYMBOL
PARAMETER
MIN
MAX
UNITS
t0
Valid Address to CS Falling Edge
0
-
ns
t1
CS Falling Edge to RD Assert
0
-
ns
t2
RD Assert to RDY Assert
-
65
ns
RD Pulse Width (t2)
70
-
ns
t3
CS Falling Edge to WR Assert
0
-
ns
t4
WR Assert to RDY Assert
-
65
ns
70
-
ns
NA
NA
WR Pulse Width (t4)
FIGURE 36. SYNCHRONOUS µP INTERFACE SIGNALS DURING PROGRAMMED I/O READ AND WRITE OPERATIONS
READ OPERATION
WRITE OPERATION
PCLK
t0
t0
Addr[7:0]
Valid Address
Valid Address
CS
D[7:0]
Valid Data for Readback
Data Available to Write Into the LIU
t1
RD
t3
WR
t2
t4
RDY
48
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 16: SYNCHRONOUS TIMING SPECIFICATIONS
SYMBOL
PARAMETER
MIN
MAX
UNITS
t0
Valid Address to CS Falling Edge
0
-
ns
t1
CS Falling Edge to RD Assert
0
-
ns
t2
RD Assert to RDY Assert
-
35
RD Pulse Width (t2)
40
-
ns
t3
CS Falling Edge to WR Assert
0
-
ns
t4
WR Assert to RDY Assert
-
35
WR Pulse Width (t4)
40
-
PCLK Period
15
NA
NA
ns, see note 1
ns, see note 1
ns
ns
PCLK Duty Cycle
PCLK "High/Low" time
NOTE: 1. This timing parameter is based on the frequency of the synchronous clock (PCLK). To determine the access
time, use the following formula: (PCLKperiod * 2) + 5ns
49
XRT75R12D
REV. 1.0.1
7.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Register Map
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0x00
CR0
APST
R/W
REGISTER NAME
APS Transmit Redundancy Control Register 0-5
CHANNEL 0 CONTROL REGISTERS
0x01
CR1
IER0
R/W
Source Level Interrupt Enable Register - Ch 0
0x02
CR2
ISR0
RUR
Source Level Interrupt Status Register Ch 0
0x03
CR3
AS0
R/O
Alarm Status Register - Ch 0
0x04
CR4
TC0
R/W
Transmit Control Register - Ch 0
0x05
CR5
RC0
R/W
Receive Control Register - Ch 0
0x06
CR6
CC0
R/W
Channel Control Register - Ch 0
0x07
CR7
JA0
R/W
Jitter Attenuator Control Register - Ch 0
0x08
CR8
APSR
R/W
APS Receive Redundancy Control Register 0-5
0x0A
CR10
EM0
R/W
Error counter MS Byte Ch 0
0x0B
CR11
EL0
R/W
Error counter LS Byte
0x0C
CR12
EH0
R/W
Error counter Holding register
0x09
0x0D
0x0E
0x0F
0x10
CHANNEL 1 CONTROL REGISTERS
0x11
CR17
IER1
R/W
Source Level Interrupt Enable Register - Ch 1
0x12
CR18
ISR1
RUR
Source Level Interrupt Status Register - Ch 1
0x13
CR19
AS1
R/O
Alarm Status Register - Ch 1
0x14
CR20
TC0
R/W
Transmit Control Register - Ch 1
0x15
CR21
RC1
R/W
Receive Control Register - Ch 1
0x16
CR22
CC1
R/W
Channel Control Register - Ch 1
0x17
CR23
JA1
R/W
Jitter Attenuator Control Register - Ch 1
0x1A
CR26
EM1
R/W
Error counter MSByte Ch 1
0x1B
CR27
EL1
R/W
Error counter LSbyte
0x1C
CR28
EH1
R/W
Error counter Holding register
0x18
0x19
50
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
REGISTER NAME
0x1D
0x1E
0x1F
0x20
CHANNEL 2 CONTROL REGISTERS
0x21
CR33
IER2
R/W
Source Level Interrupt Enable Register - Ch 2
0x22
CR34
ISR2
RUR
Source Level Interrupt Status Register - Ch 2
0x23
CR35
AS2
R/O
Alarm Status Register - Ch 2
0x24
CR36
TC2
R/W
Transmit Control Register - Ch 2
0x25
CR37
RC2
R/W
Receive Control Register - Ch 2
0x26
CR38
CC2
R/W
Channel Control Register - Ch 2
0x27
CR39
JA2
R/W
Jitter Attenuator Control Register - Ch 2
0x2A
CR42
EM2
R/W
Error counter MSByte Ch 2
0x2B
CR43
EL2
R/W
Error counter LSbyte
0x2C
CR44
EH2
R/W
Error counter Holding register
0x28
0x29
0x2D
0x2E
0x2F
0x30
CHANNEL 3 CONTROL REGISTERS
0x31
CR49
IER3
R/W
Source Level Interrupt Enable Register - Ch 3
0x32
CR50
ISR3
RUR
Source Level Interrupt Status Register - Ch 3
0x33
CR51
AS3
R/O
Alarm Status Register - Ch 3
0x34
CR52
TC3
R/W
Transmit Control Register - Ch 3
0x35
CR53
RC3
R/W
Receive Control Register - Ch 3
0x36
CR54
CC3
R/W
Channel Control Register - Ch 3
0x37
CR55
JA3
R/W
Jitter Attenuator Control Register - Ch 3
CR58
EM3
R/W
Error counter MSByte Ch 3
0x38
0x39
0x3A
51
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0x3B
CR59
EL3
R/W
Error counter LSbyte
0x3C
CR60
EH3
R/W
Error counter Holding register
REGISTER NAME
0x3D
0x3E
0x3F
0x40
CHANNEL 4 CONTROL REGISTERS
0x41
CR65
IER4
R/W
Source Level Interrupt Enable Register - Ch 4
0x42
CR66
ISR4
RUR
Source Level Interrupt Status Register - Ch 4
0x43
CR67
AS4
R/O
Alarm Status Register - Ch 4
0x44
CR68
TC4
R/W
Transmit Control Register - Ch 4
0x45
CR69
RC4
R/W
Receive Control Register - Ch 4
0x46
CR70
CC4
R/W
Channel Control Register - Ch 4
0x47
CR71
JA4
R/W
Jitter Attenuator Control Register - Ch 4
0x4A
CR74
EM4
R/W
Error counter MSByte Ch 4
0x4B
CR75
EL4
R/W
Error counter LSbyte
0x4C
CR76
EH4
R/W
Error counter Holding register
0x48
0x49
0x4D
0x4E
0x4F
0x50
CHANNEL 5 CONTROL REGISTERS
0x51
CR81
IER5
R/W
Source Level Interrupt Enable Register - Ch 5
0x52
CR82
ISR5
RUR
Source Level Interrupt Status Register - Ch 5
0x53
CR83
AS5
R/O
Alarm Status Register - Ch 5
0x54
CR84
TC5
R/W
Transmit Control Register - Ch 5
0x55
CR85
RC5
R/W
Receive Control Register - Ch 5
0x56
CR86
CC5
R/W
Channel Control Register - Ch 5
0x57
CR87
JA5
R/W
Jitter Attenuator Control Register - Ch 5
0x58
52
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0x5A
CR90
EM5
R/W
Error counter MSByte Ch 5
0x5B
CR91
EL5
R/W
Error counter LSbyte
0x5C
CR92
EH5
R/W
Error counter Holding register
0x60
CR96
CIE
R/W
Channel 0-5 Interrupt Enable flags
0x61
CR97
CIS
R/O
Channel 0-5 Interrupt status flags
0x6E
CR110
PN
R/O
Device Part Number Register
0x6F
CR111
VN
R/O
Chip Revision Number Register
REGISTER NAME
0x59
0x5D
0x5E
0x5F
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x65
0x69
0x6A
0x6B
0x6C
0x6D
0x70
0x71
0x72
0x73
0x74
0x75
0x76
0x77
53
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
CR128
APST
R/W
REGISTER NAME
0x78
0x75
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
0x7F
0x80
APS Transmit Redundancy Control Register 6-11
CHANNEL 6 CONTROL REGISTERS
0x81
CR129
IER6
R/W
Source Level Interrupt Enable Register - Ch 6
0x82
CR130
ISR6
RUR
Source Level Interrupt Status Register - Ch 6
0x83
CR131
AS6
R/O
Alarm Status Register - Ch 6
0x84
CR132
TC6
R/W
Transmit Control Register - Ch 6
0x85
CR133
RC6
R/W
Receive Control Register - Ch 6
0x86
CR134
CC6
R/W
Channel Control Register - Ch 6
0x87
CR135
JA6
R/W
Jitter Attenuator Control Register - Ch 6
0x88
CR136
APSR
R/W
APS Receive Redundancy Control Register 6-11
0x8A
CR138
EM6
R/W
Error counter MSByte Ch 6
0x8B
CR139
EL6
R/W
Error counter LSbyte
0x8C
CR140
EH6
R/W
Error counter Holding register
0x89
0x8D
0x8E
0x8F
0x90
CHANNEL 7 CONTROL REGISTERS
0x91
CR145
IER7
R/W
Source Level Interrupt Enable Register - Ch 7
0x92
CR146
ISR7
RUR
Source Level Interrupt Status Register - Ch 7
0x93
CR147
AS7
R/O
Alarm Status Register - Ch 7
0x94
CR148
TC7
R/W
Transmit Control Register - Ch 7
54
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0x95
CR149
RC7
R/W
Receive Control Register - Ch 7
0x96
CR150
CC7
R/W
Channel Control Register - Ch 7
0x97
CR151
JA7
R/W
Jitter Attenuator Control Register - Ch 7
0x9A
CR154
EM7
R/W
Error counter MSByte Ch 7
0x9B
CR155
EL7
R/W
Error counter LSbyte
0x9C
CR156
EH7
R/W
Error counter Holding register
REGISTER NAME
0x98
0x99
0x9D
0x9E
0x9F
0xA0
CHANNEL 8 CONTROL REGISTERS
0xA1
CR161
IER8
R/W
Source Level Interrupt Enable Register - Ch 8
0xA2
CR162
ISR8
RUR
Source Level Interrupt Status Register - Ch 8
0xA3
CR163
AS8
R/O
Alarm Status Register - Ch 8
0xA4
CR164
TC8
R/W
Transmit Control Register - Ch 8
0xA5
CR165
RC8
R/W
Receive Control Register - Ch 8
0xA6
CR166
CC8
R/W
Channel Control Register - Ch 8
0xA7
CR167
JA8
R/W
Jitter Attenuator Control Register - Ch 8
0xAA
CR170
EM8
R/W
Error counter MSByte Ch 8
0xAB
CR171
EL8
R/W
Error counter LSbyte
0xAC
CR172
EH8
R/W
Error counter Holding register
0xA8
0xA9
0xAD
0xAE
0xAF
0xB0
CHANNEL 9 CONTROL REGISTERS
0xB1
CR177
IER9
R/W
Source Level Interrupt Enable Register - Ch 9
0xB2
CR178
ISR9
RUR
Source Level Interrupt Status Register - Ch 9
55
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0xB3
CR179
AS9
R/O
Alarm Status Register - Ch 9
0xB4
CR180
TC9
R/W
Transmit Control Register - Ch 9
0xB5
CR181
RC9
R/W
Receive Control Register - Ch 9
0xB6
CR182
CC9
R/W
Channel Control Register - Ch 9
0xB7
CR183
JA9
R/W
Jitter Attenuator Control Register - Ch 9
0xBA
CR186
EM9
R/W
Error counter MSByte Ch 9
0xBB
CR187
EL9
R/W
Error counter LSbyte
0xBC
CR188
EH9
R/W
Error counter Holding register
REGISTER NAME
0xB8
0xB9
0xBD
0xBE
0xBF
0xC0
CHANNEL 10 CONTROL REGISTERS
0xC1
CR193
IER10
R/W
Source Level Interrupt Enable Register - Ch 10
0xC2
CR194
ISR10
RUR
Source Level Interrupt Status Register - Ch 10
0xC3
CR195
AS10
R/O
Alarm Status Register - Ch 10
0xC4
CR196
TC10
R/W
Transmit Control Register - Ch 10
0xC5
CR197
RC10
R/W
Receive Control Register - Ch 10
0xC6
CR198
CC10
R/W
Channel Control Register - Ch 10
0xC7
CR199
JA10
R/W
Jitter Attenuator Control Register - Ch 10
0xCA
CR202
EM10
R/W
Error counter MSByte Ch 10
0xCB
CR203
EL10
R/W
Error counter LSbyte
0xCC
CR204
EH10
R/W
Error counter Holding register
0xC8
0xC9
0xCD
0xCE
0xCF
0xD0
CHANNEL 11 CONTROL REGISTERS
56
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0xD1
CR209
IER11
R/W
Source Level Interrupt Enable Register - Ch 11
0xD2
CR210
ISR11
RUR
Source Level Interrupt Status Register - Ch 11
0xD3
CR211
AS11
R/O
Alarm Status Register - Ch 11
0xD4
CR212
TC11
R/W
Transmit Control Register - Ch 11
0xD5
CR213
RC11
R/W
Receive Control Register - Ch 11
0xD6
CR214
CC11
R/W
Channel Control Register - Ch 11
0xD7
CR215
JA11
R/W
Jitter Attenuator Control Register - Ch 11
0xDA
CR218
EM11
R/W
Error counter MSByte Ch 11
0xDB
CR219
EL11
R/W
Error counter LSbyte
0xDC
CR229
EH11
R/W
Error counter Holding register
0xE0
CR224
CIE
R/W
Channel 6-11 Interrupt enable flags
0xE1
CR225
CIS
R/O
Channel 6-11 Interrupt status flags
REGISTER NAME
0xD8
0xD9
0xDD
0xDE
0xDF
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
0xE8
0xE5
0xE9
0xEA
0xEB
0xEC
0xED
0xEE
0xEF
57
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 17: COMMAND REGISTER ADDRESS MAP, WITHIN THE XRT75R12D
ADDRESS
(HEX)
COMMAND REGISTER
(DECIMAL)
LABEL
TYPE
0xF0
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
0xF7
0xF8
0xF5
0xF9
0xFA
0xFB
0xFC
0xFD
0xFE
0xFF
58
REGISTER NAME
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
THE GLOBAL/CHIP-LEVEL REGISTERS
The register set, within the XRT75R12D contains ten global or chip-level registers. These registers control
operations in more than one channel or apply to the complete chip. This section will present detailed
information on the Global Registers.
TABLE 18: LIST AND ADDRESS LOCATIONS OF GLOBAL REGISTERS
ADDRESS
COMMAND
REGISTER
LABEL
TYPE
0x00
CR0
APST
R/W
APS Transmit Redundancy Control Register 0-5
0x08
CR8
APSR
R/W
APS Receive Redundancy Control Register 0-5
0x80
CR128
APST
R/W
APS Transmit Redundancy Control Register 6-11
0x88
CR136
APSR
R/W
APS Receive Redundancy Control Register 6-11
0x60
CR96
CIE
R/W
Channel 0-5 Interrupt Enable flags
0x61
CR97
CIS
R/O
Channel 0-5 Interrupt status flags
0xE0
CR224
CIE
R/W
Channel 6-11 Interrupt enable flags
0xE1
CR225
CIS
R/O
Channel 6-11 Interrupt status flags
0x6E
CR110
PN
ROM
Device Part Number Register
0x6F
CR111
VN
ROM
Chip Revision/Version Number Register
REGISTER NAME
REGISTER DESCRIPTION - GLOBAL REGISTERS
TABLE 19: APS/REDUNDANCY TRANSMIT CONTROL REGISTER - CR0 (ADDRESS LOCATION = 0X00)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reserved
Reserved
TxON Ch 5
TxON Ch 4
TxON Ch 3
TxON Ch 2
TxON Ch 1
TxON Ch 0
R/W
R/W
R/W
R/W
R/W
R/W
BIT
NUMBER
NAME
7,6
Reserved
5
4
3
2
1
0
TxON Ch 5
TxON Ch 4
TxON Ch 3
TxON Ch 2
TxON Ch 1
TxON Ch 0
TYPE
DESCRIPTION
R/W
Transmit Section ON - Channel n
This READ/WRITE bit-field is used to turn on or turn off the Transmit Driver associated with Channel n. If the user turns on the Transmit Driver, then Channel n will
transmit DS3, E3 or STS-1 pulses on the line via the TTIP_n and TRING_ n output
pins.
Conversely, if the user turns off the Transmit Driver, then the TTIP_n and TRING_n
output pins will be tri-stated.
0 - Shuts off the Transmit Driver associated with Channel n and tri-states the TTIP_n
and TRING_ n output pins.
1 - Turns on the Transmit Driver associated with Channel n.
NOTE: The master TxON control pin(pin # P4) must be in a high state (logic 1) for
this operation to turn on any channel.
59
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 20: APS/REDUNDANCY TRANSMIT CONTROL REGISTER - CR8 (ADDRESS LOCATION = 0X08)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reserved
Reserved
TxON Ch 11
TxON Ch 10
TxON Ch 9
TxON Ch 8
TxON Ch 7
TxON Ch 6
R/W
R/W
R/W
R/W
R/W
R/W
BIT
NUMBER
NAME
7,6
Reserved
5
4
3
2
1
0
TxON Ch 11
TxON Ch 10
TxON Ch 9
TxON Ch 8
TxON Ch 7
TxON Ch 6
TYPE
DESCRIPTION
R/W
Transmit Section ON - Channel n
This READ/WRITE bit-field is used to turn on or turn off the Transmit Driver associated with Channel n on a per channel basis. If the user turns on the Transmit Driver,
then Channel n will transmit DS3, E3 or STS-1 pulses on the line via the TTIP_n and
TRING_ n output pins.
Conversely, if the user turns off the Transmit Driver (for channel n), the TTIP_n and
TRING_n output pins will be tri-stated.
0 - Shuts off the Transmit Driver associated with Channel n and tri-states the TTIP_n
and TRING_ n output pins.
1 - Turns on the Transmit Driver associated with Channel n.
NOTE: The master TxON control (pin # P4) must be in a high state (logic 1) for this
operation to turn on any channel.
60
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 21: CHANNEL LEVEL INTERRUPT ENABLE REGISTER - CR96 (ADDRESS LOCATION = 0X60)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reserved
Reserved
Channel 5
Interrupt
Enable
Channel 4
Interrupt
Enable
Channel 3
Interrupt
Enable
Channel 2
Interrupt
Enable
Channel 1
Interrupt
Enable
Channel 0
Interrupt
Enable
R/W
R/W
R/W
R/W
R/W
R/W
Register - CR96 (Address Location = 0x60)
BIT
NUMBER
NAME
7,6
Unused
5
4
3
2
1
0
Channel 5 Interrupt Enable
Channel 4 Interrupt Enable
Channel 3 Interrupt Enable
Channel 2 Interrupt Enable
Channel 1 Interrupt Enable
Channel 0 Interrupt Enable
TYPE
R/W
DESCRIPTION
Channel n Interrupt Enable Bit:
This READ/WRITE bit is used to:
• To enable Channel n for Interrupt Generation at the Channel
Level
• To disable all Interrupts associated with Channel n within the
XRT75R12D
This is a "master" enable bit for each channel. This bit allows
control on a per channel basis to signal the Host of selected error
conditions.
If a bit is cleared, no interrupts from that channel will be sent to the
Host via the INT.
If the bit is set (logic 1), any generated interrupt in channel n that
has been enabled in the Interrupt Enable register (IERn) for the
channel will activate the INT pin to the Host.
0 - Disables all Channel n related Interrupts.
1 - Enables Channel n-related Interrupts. The user must enable
individual Channel n related Interrupts at the source level, before
they are can generate an interrupt.
61
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 22: CHANNEL LEVEL INTERRUPT ENABLE REGISTER - CR224 (ADDRESS LOCATION = 0XE0)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Reserved
Reserved
Channel 11
Interrupt
Enable
Channel 10
Interrupt
Enable
Channel 9
Interrupt
Enable
Channel 8
Interrupt
Enable
Channel 7
Interrupt
Enable
Channel 6
Interrupt
Enable
R/W
R/W
R/W
R/W
R/W
R/W
REGISTER - CR224 (ADDRESS LOCATION = 0XE0)
BIT
NUMBER
NAME
7,6
Reserved
5
4
3
2
1
0
Channel 11 Interrupt Enable
Channel 10 Interrupt Enable
Channel 9 Interrupt Enable
Channel 8 Interrupt Enable
Channel 7 Interrupt Enable
Channel 6 Interrupt Enable
TYPE
R/W
DESCRIPTION
Channel n Interrupt Enable Bit:
This READ/WRITE bit is used to:
• To enable Channel n for Interrupt Generation at the Channel
Level
• To disable all Interrupts associated with Channel n within the
XRT75R12D
This is a "master" enable bit for each channel. This bit allows
control on a per channel basis to signal the Host of selected error
conditions.
If a bit is cleared, no interrupts from that channel will be sent to the
Host via the INT pin.
If the bit is set (logic 1), any generated interrupt in channel n that
has been enabled in the Interrupt Enable register (IERn) for the
channel will activate the INT pin to the Host.
0 - Disables all Channel n related Interrupts.
1 - Enables Channel n-related Interrupts. The user must enable
individual Channel n related Interrupts at the source level, before
they are can generate an interrupt.
62
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 23: CHANNEL LEVEL INTERRUPT STATUS REGISTER - CR97 (ADDRESS LOCATION = 0X61)
BIT 7
BIT 6
Reserved Reserved
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Channel 5
Channel 4
Channel 3
Channel 2
Channel 1
Channel 0
Interrupt Status Interrupt Status Interrupt Status Interrupt Status Interrupt Status Interrupt Status
R/O
R/O
R/O
R/O
R/O
R/O
Register - CR97 (Address Location = 0x61)
BIT
NUMBER
NAME
7, 6
Reserved
5
4
3
2
1
0
Channel 5 Interrupt Status
Channel 4 Interrupt Status
Channel 3 Interrupt Status
Channel 2 Interrupt Status
Channel 1 Interrupt Status
Channel 0 Interrupt Status
TYPE
DESCRIPTION
R/O
Channel n Interrupt Status Bit:
This READ-ONLY bit-field indicates whether the XRT75R12D has a
pending Channel n-related interrupt that is awaiting service. The first
six channels are serviced through this location and the other six at
address 0xE1. These two registers are used by the Host to identify
the source channel of an active interrupt.
0 - Indicates that there is NO Channel n-related Interrupt awaiting service.
1 - Indicates that there is at least one Channel n-related Interrupt
awaiting service. In this case, the user's Interrupt Service routine
should be written such that the Microprocessor will now proceed to
read out the contents of the Source Level Interrupt Status Register Channel n (Address Locations = 0xn2) to determine the exact source
of the interrupt request.
NOTE: Once this bit-field is set to "1", it will not be cleared back to "0"
until the user has read out the contents of the Source-Level
Interrupt Status Register bit, that corresponds to the interrupt
request channel.
63
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 24: CHANNEL LEVEL INTERRUPT STATUS REGISTER - CR225 (ADDRESS LOCATION = 0XE1)
BIT 7
BIT 6
BIT 5
Reserved Reserved
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Channel 11
Channel 10
Channel 9
Channel 8
Channel 7
Channel 6
Interrupt Status Interrupt Status Interrupt Status Interrupt Status Interrupt Status Interrupt Status
R/O
R/O
R/O
R/O
R/O
R/O
Register - CR225 (Address Location = 0xE1)
BIT
NUMBER
NAME
7, 6
Reserved
5
4
3
2
1
0
Channel 11 Interrupt Status
Channel 10 Interrupt Status
Channel 9 Interrupt Status
Channel 8 Interrupt Status
Channel 7 Interrupt Status
Channel 6 Interrupt Status
TYPE
DESCRIPTION
R/O
Channel n Interrupt Status Bit:
This READ-ONLY bit-field indicates whether the XRT75R12D has a
pending Channel n-related interrupt that is awaiting service. The last
six channels are serviced through this location and the other six at
address 0x61. These two registers are used by the Host to identify the
source channel of an active interrupt.
0 - Indicates that there is NO Channel n-related Interrupt awaiting service.
1 - Indicates that there is at least one Channel n-related Interrupt
awaiting service. In this case, the user's Interrupt Service routine
should be written such that the Microprocessor will now proceed to
read out the contents of the Source Level Interrupt Status Register Channel n (Address Locations = 0xn2) to determine the exact source
of the interrupt request.
NOTE: Once this bit-field is set to "1", it will not be cleared back to "0"
until the user has read out the contents of the Source-Level
Interrupt Status Register bit, that corresponds to the interrupt
request channel.
TABLE 25: DEVICE/PART NUMBER REGISTER - CR110 (ADDRESS LOCATION = 0X6E)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Part Number ID Value
R/O
R/O
R/O
R/O
R/O
R/O
R/O
R/O
0
1
0
1
1
0
0
0
Register - CR110 (Address Location = 0x6E)
BIT NUMBER
NAME
TYPE
DEFAULT
VALUE
7-0
Part Number ID
Value
R/O
0x58
DESCRIPTION
Part Number ID Value:
This READ-ONLY register contains a unique value for the
XRT75R12D. This value will always be 0x58.
64
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 26: CHIP REVISION NUMBER REGISTER - CR111 (ADDRESS LOCATION = 0X6F)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Chip Revision Number Value
R/O
R/O
R/O
R/O
R/O
R/O
R/O
R/O
0
0
0
0
X
X
X
X
Register - CR111 (Address Location = 0x6F
BIT NUMBER
NAME
TYPE
DEFAULT
VALUE
7-0
Chip Revision
Number Value
R/O
0x0#
DESCRIPTION
Chip Revision Number Value:
This READ-ONLY register contains a value that represents
the current revision of this XRT75R12D. This revision number will always be in the form of "0x0#", where "#" is a hexadecimal value that specifies the current revision of the chip.
For example, the very first revision of this chip will contain
the value "0x01".
65
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
THE PER-CHANNEL REGISTERS
The XRT75R12D consists of 120 per-Channel Registers (12 channels and 10 registers per channel). Table 27
presents the overall Register Map with the Per-Channel Registers unshaded.
REGISTER DESCRIPTION - PER CHANNEL REGISTERS
TABLE 27: XRT75R12D REGISTER MAP SHOWING INTERRUPT ENABLE REGISTERS (IER_N)
ADDRESS
LOCATION
0
1
2
3
4
5
6
7
8
0x0-
APST
IER0
ISR0
AS0
TC0
RC0
CC0
JA0
APSR
0X1-
IER1
ISR1
AS1
TC1
RC1
CC1
0x2-
IER2
ISR2
AS2
TC2
RC2
0x3-
IER3
ISR3
AS3
TC3
0x4-
IER4
ISR4
AS4
0x5-
IER5
ISR5
AS5
0x6-
A
B
C
EM0
EL0
EH0
JA1
EM1
EL1
EH1
CC2
JA2
EM2
EL2
EH2
RC3
CC3
JA3
EM3
EL3
EH3
TC4
RC4
CC4
JA4
EM4
EL4
EH4
TC5
RC5
CC5
JA5
EM5
EL5
EH5
CIE
CIS
APST
IER6
ISR6
AS6
TC6
RC6
CC6
JA6
0X9-
IER7
ISR7
AS7
TC7
RC7
CC7
0xA-
IER8
ISR8
AS8
TC8
RC8
0xB-
IER9
ISR9
AS9
TC9
0xC-
IER10
ISR10
AS10
0xD-
IER11
ISR11
AS11
9
PN VN
0x70x8-
0xE-
CIE
D E F
EM6
EL6
EH6
JA7
EM7
EL7
EH7
CC8
JA8
EM8
EL8
EH8
RC9
CC9
JA9
EM9
EL9
EH9
TC10
RC10
CC10
JA10
EM10
EL10
EH10
TC11
RC11
CC11
JA11
EM11
EL11
EH11
CIS
0xF-
66
APSR
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 28: SOURCE LEVEL INTERRUPT ENABLE REGISTER - CHANNEL N ADDRESS LOCATION = 0XM1
(M = 0-5 & 8-D)
BIT 7
BIT 6
BIT 5
BIT 4
Reserved
BIT 3
BIT 2
BIT 1
BIT 0
Change of FL Change of LOL Change of LOS
Change of
Condition
Condition
Condition
DMO Condition
Interrupt Enable Interrupt Enable Interrupt Enable Interrupt Enable
Ch n
Ch n
Ch n
Ch n
R/W
BIT NUMBER
NAME
TYPE
7-4
Reserved
R/O
3
Change of FL
Condition Interrupt
Enable - Ch n
R/W
R/W
R/W
R/W
DESCRIPTION
Change of FL (FIFO Limit Alarm) Condition Interrupt Enable - Ch n:
This READ/WRITE bit-field is used to enable or disable the Change of FIFO
Limit Alarm Condition Interrupt. If the user enables this interrupt, the
XRT75R12D will generate an interrupt if any of the following events occur.
• Whenever the Jitter Attenuator (within Channel n) declares the FL (FIFO
Limit Alarm) condition.
• Whenever the Jitter Attenuator (within Channel n) clears the FL (FIFO
Limit Alarm) condition.
0 - Disables the Change in FL Condition Interrupt.
1 - Enables the Change in FL Condition Interrupt.
2
Change of LOL
Condition Interrupt
Enable
R/W
Change of Receive LOL (Loss of Lock) Condition Interrupt Enable Channel n:
This READ/WRITE bit-field is used to enable or disable the Change of
Receive LOL Condition Interrupt. If the user enables this interrupt, then the
XRT75R12D will generate an interrupt any time any of the following events
occur.
• Whenever the Receive Section (within Channel n) declares the Loss of
Lock Condition.
• Whenever the Receive Section (within Channel n) clears the Loss of Lock
Condition.
0 - Disables the Change in Receive LOL Condition Interrupt.
1 - Enables the Change in Receive LOL Condition Interrupt.
67
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
BIT NUMBER
NAME
TYPE
DESCRIPTION
1
Change of LOS
Condition Interrupt
Enable
R/W
Change of the Receive LOS (Loss of Signal) Defect Condition Interrupt
Enable - Ch 0:
This READ/WRITE bit-field is used to enable or disable the Change of the
Receive LOS Defect Condition Interrupt. If the user enables this interrupt,
then the XRT75R12D will generate an interrupt any time any of the following
events occur.
• Whenever the Receive Section (within Channel n) declares the LOS
Defect Condition.
• Whenever the Receive Section (within Channel n) clears the LOS Defect
condition.
0 - Disables the Change in the LOS Defect Condition Interrupt.
1 - Enables the Change in the LOS Defect Condition Interrupt.
0
Change of DMO
Condition Interrupt
Enable
R/W
Change of Transmit DMO (Drive Monitor Output) Condition Interrupt
Enable - Ch n:
This READ/WRITE bit-field is used to enable or disable the Change of
Transmit DMO Condition Interrupt. If the user enables this interrupt, then
the XRT75R12D will generate an interrupt any time any of the following
events occur.
• Whenever the Transmit Section toggles the DMO output pin (or bit-field)
to "1".
• Whenever the Transmit Section toggles the DMO output pin (or bit-field)
to "0".
0 - Disables the Change in the DMO Condition Interrupt.
1 - Enables the Change in the DMO Condition Interrupt.
68
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 29: XRT75R12D REGISTER MAP SHOWING ALARM STATUS REGISTERS (AS_N)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
Reserved
Loss of PRBS
Pattern Sync
Digital LOS
Defect
Declared
Analog LOS
Defect
Declared
FL
(FIFO Limit)
Alarm
Declared
R/O
R/O
R/O
R/O
BIT 2
BIT 1
Receive LOL Receive LOS
Defect
Defect
Declared
Declared
R/O
R/O
BIT 0
Transmit
DMO
Condition
R/O
Source Level Interrupt Status Register - Channel n Address Location = 0xm2
BIT NUMBER
NAME
7-4
Reserved
3
Change of FL Condition Interrupt Status
TYPE
DESCRIPTION
RUR
Change of FL (FIFO Limit Alarm) Condition Interrupt Status - Ch n:
This RESET-upon-READ bit-field indicates whether or not the Change of FL
Condition Interrupt (for Channel n) has occurred since the last read of this
register.
0 - Indicates that the Change of FL Condition Interrupt has NOT occurred
since the last read of this register.
1 - Indicates that the Change of FL Condition Interrupt has occurred since
the last read of this register.
NOTE:
2
Change of LOL Condition Interrupt Status
RUR
The user can determine the current state of the FIFO Alarm
condition by reading out the contents of Bit 3 (FL Alarm Declared)
within the Alarm Status Register.(n)
Change of Receive LOL (Loss of Lock) Condition Interrupt Status - Ch
n:
This RESET-upon-READ bit-field indicates whether or not the Change of
Receive LOL Condition Interrupt (for Channel n) has occurred since the last
read of this register.
0 - Indicates that the Change of Receive LOL Condition Interrupt has NOT
occurred since the last read of this register.
1 - Indicates that the Change of Receive LOL Condition Interrupt has
occurred since the last read of this register.
NOTE: The user can determine the current state of the Receive LOL Defect
condition by reading out the contents of Bit 2 (Receive LOL Defect
Declared) within the Alarm Status Register.(n)
69
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Source Level Interrupt Status Register - Channel n Address Location = 0xm2
BIT NUMBER
NAME
TYPE
DESCRIPTION
1
Change of LOS
Condition Interrupt
Status
RUR
Change of Receive LOS (Loss of Signal) Defect Condition Interrupt
Status:
This RESET-upon-READ bit-field indicates whether or not the Change of
the Receive LOS Defect Condition Interrupt (for Channel n) has occurred
since the last read of this register.
0 - Indicates that the Change of the Receive LOS Defect Condition Interrupt
has NOT occurred since the last read of this register.
1 - Indicates that the Change of the Receive LOS Defect Condition Interrupt
has occurred since the last read of this register.
NOTE: The user can determine the current state of the Receive LOS Defect
condition by reading out the contents of Bit 1 (Receive LOS Defect
Declared) within the Alarm Status Register.(n)
0
Change of DMO
Condition Interrupt
Status
RUR
Change of Transmit DMO (Drive Monitor Output) Condition Interrupt
Status - Ch n:
This RESET-upon-READ bit-field indicates whether or not the Change of
the Transmit DMO Condition Interrupt (for Channel n) has occurred since
the last read of this register.
0 - Indicates that the Change of the Transmit DMO Condition Interrupt has
NOT occurred since the last read of this register.
1 - Indicates that the Change of the Transmit DMO Condition Interrupt has
occurred since the last read of this register.
NOTE: The user can determine the current state of the Transmit DMO
Condition by reading out the contents of Bit 0 (Transmit DMO
Condition) within the Alarm Status Register.(n)
70
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 30: XRT75R12 REGISTER MAP SHOWING ALARM STATUS REGISTERS (AS_N)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
Reserved
Loss of PRBS
Pattern Sync
Digital LOS
Defect
Declared
Analog LOS
Defect
Declared
FL
(FIFO Limit)
Alarm
Declared
R/O
R/O
R/O
R/O
BIT 2
BIT 1
Receive LOL Receive LOS
Defect
Defect
Declared
Declared
R/O
BIT 0
Transmit
DMO
Condition
R/O
R/O
ALARM STATUS REGISTER - CHANNEL N ADDRESS LOCATION = 0XM3
BIT NUMBER
NAME
7
Reserved
6
Loss of PRBS Pattern Lock
TYPE
DESCRIPTION
R/O
Loss of PRBS Pattern Lock Indicator:
This READ-ONLY bit-field indicates whether or not the PRBS Receiver
(within the Receive Section of Channel n) is declaring PRBS Lock within the
incoming PRBS pattern.
If the PRBS Receiver detects a very large number of bit-errors within its
incoming data-stream, then it will declare the Loss of PRBS Lock Condition.
Conversely, if the PRBS Receiver were to detect its pre-determined PRBS
pattern with the incoming DS3, E3 or STS-1 data-stream, (with little or no bit
errors) then the PRBS Receiver will clear the Loss of PRBS Lock condition.
0 - Indicates that the PRBS Receiver is currently declaring the PRBS Lock
condition within the incoming DS3, E3 or STS-1 data-stream.
1 - Indicates that the PRBS Receiver is currently declaring the Loss of PRBS
Lock condition within the incoming DS3, E3 or STs-1 data-stream.
NOTE: This register bit is only valid if all of the following are true.
a. The PRBS Generator block (within the Transmit Section of the Chip is
enabled).
b. The PRBS Receiver is enabled.
c. The PRBS Pattern (that is generated by the PRBS Generator) is
somehow looped back into the Receive Path (via the Line-Side) and
in-turn routed to the receive input of the PRBS Receiver.
71
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
ALARM STATUS REGISTER - CHANNEL N ADDRESS LOCATION = 0XM3
BIT NUMBER
NAME
TYPE
DESCRIPTION
5
Digital LOS Defect
Declared
R/O
Digital LOS Defect Declared:
This READ-ONLY bit-field indicates whether or not the Digital LOS (Loss of
Signal) detector is declaring the LOS Defect condition.
For DS3 and STS-1 applications, the Digital LOS Detector will declare the
LOS Defect condition whenever it detects an absence of pulses (within the
incoming DS3 or STS-1 data-stream) for 160 consecutive bit-periods.
Further, (again for DS3 and STS-1 applications) the Digital LOS Detector will
clear the LOS Defect condition whenever it determines that the pulse density
(within the incoming DS3 or STS-1 signal) is at least 33%.
0 - Indicates that the Digital LOS Detector is NOT declaring the LOS Defect
Condition.
1 - Indicates that the Digital LOS Detector is currently declaring the LOS
Defect condition.
NOTES:
4
Analog LOS Defect
Declared
R/O
1.
LOS Detection (within each channel of the XRT75R12D) is
performed by both an Analog LOS Detector and a Digital LOS
Detector. The LOS state of a given Channel is simply a WIREDOR of the LOS Defect Declare states of these two detectors.
2.
The current LOS Defect Condition (for the channel) can be
determined by reading out the contents of Bit 1 (Receive LOS
Defect Declared) within this register.
Analog LOS Defect Declared:
This READ-ONLY bit-field indicates whether or not the Analog LOS (Loss of
Signal) detector is declaring the LOS Defect condition.
For DS3 and STS-1 applications, the Analog LOS Detector will declare the
LOS Defect condition whenever it determines that the amplitude of the
pulses (within the incoming DS3/STS-1 line signal) drops below a certain
Analog LOS Defect Declaration threshold level.
Conversely, (again for DS3 and STS-1 applications) the Analog LOS Detector will clear the LOS Defect condition whenever it determines that the amplitude of the pulses (within the incoming DS3/STS-1 line signal) has risen
above a certain Analog LOS Defect Clearance threshold level.
It should be noted that, in order to prevent "chattering" within the Analog
LOS Detector output, there is some built-in hysteresis between the Analog
LOS Defect Declaration and the Analog LOS Defect Clearance threshold
levels.
0 - Indicates that the Analog LOS Detector is NOT declaring the LOS Defect
Condition.
1 - Indicates that the Analog LOS Detector is currently declaring the LOS
Defect condition.
NOTES:
1.
LOS Detection (within each channel of the XRT75R12D) is
performed by both an Analog LOS Detector and a Digital LOS
Detector. The LOS state of a given Channel is simply a WIREDOR of the LOS Defect Declare states of these two detectors.
2.
The current LOS Defect Condition (for the channel) can be
determined by reading out the contents of Bit 1 (Receive LOS
Defect Declared) within this register.
72
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
ALARM STATUS REGISTER - CHANNEL N ADDRESS LOCATION = 0XM3
BIT NUMBER
NAME
TYPE
DESCRIPTION
3
FL Alarm Declared
R/O
FL (FIFO Limit) Alarm Declared:
This READ-ONLY bit-field indicates whether or not the Jitter Attenuator
block (within Channel_n) is currently declaring the FIFO Limit Alarm.
The Jitter Attenuator block will declare the FIFO Limit Alarm anytime the Jitter Attenuator FIFO comes within two bit-periods of either overflowing or
under-running.
Conversely, the Jitter Attenuator block will clear the FIFO Limit Alarm anytime the Jitter Attenuator FIFO is NO longer within two bit-periods of either
overflowing or under-running.
Typically, this Alarm will only be declared whenever there is a very serious
problem with timing or jitter in the system.
0 - Indicates that the Jitter Attenuator block (within Channel_n) is NOT currently declaring the FIFO Limit Alarm condition.
1 - Indicates that the Jitter Attenuator block (within Channel_n) is currently
declaring the FIFO Limit Alarm condition.
NOTE: This bit-field is only active if the Jitter Attenuator (within Channel_n)
has been enabled.
2
Receive LOL Condition Declared
R/O
Receive LOL (Loss of Lock) Condition Declared:
This READ-ONLY bit-field indicates whether or not the Receive Section
(within Channel_n) is currently declaring the LOL (Loss of Lock) condition.
The Receive Section (of Channel_n) will declare the LOL Condition, if the
frequency of the Recovered Clock signal differs from that of the reference
clock programmed for that channel (from the appropriate oscillator or the
SFM clock synthesizer if in that mode) by 0.5% (or 5000ppm) or more .
0 - Indicates that the Receive Section of Channel_n is NOT currently declaring the LOL Condition.
1 - Indicates that the Receive Section of Channel_n is currently declaring the
LOL Condition and the recovered clock differs by more than 0.5%..
73
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
ALARM STATUS REGISTER - CHANNEL N ADDRESS LOCATION = 0XM3
BIT NUMBER
NAME
TYPE
DESCRIPTION
1
Receive LOS Defect
Condition Declared
R/O
Receive LOS (Loss of Signal) Defect Condition Declared:
This READ-ONLY bit-field indicates whether or not the Receive Section
(within Channel_n) is currently declaring the LOS defect condition.
The Receive Section (of Channel_n) will declare the LOS defect condition, if
any one of the following conditions is met.
• If the Digital LOS Detector declares the LOS defect condition (for DS3 or
STS-1 applications)
• If the Analog LOS Detector declares the LOS defect condition (for DS3 or
STS-1 applications)
• If the ITU-T G.775 LOS Detector declares the LOS defect condition (for E3
applications).
0 - Indicates that the Receive Section of Channel_n is NOT currently declaring the LOS Defect Condition.
1 - Indicates that the Receive Section of Channel_n is currently declaring the
LOS Defect condition.
0
Transmit DMO Condition Declared
R/O
Transmit DMO (Drive Monitor Output) Condition Declared:
This READ-ONLY bit-field indicates whether or not the Transmit Section of
Channel_n is currently declaring the DMO Alarm condition.
As configured, the Transmit Section will either internally (via the TTIP_n and
TRING_n ) or externally (via the MTIP_n and MRING_n) check the Transmit
Output DS3/E3/STS-1 Line signal for bipolar pulses. If the Transmit Section
were to detect no bipolar for 128 consecutive bit-periods, then it will declare
the Transmit DMO Alarm condition. This particular alarm can be used to
check for fault conditions on the Transmit Output Line Signal path.
The Transmit Section will clear the Transmit DMO Alarm condition upon
detecting bipolar activity on the Transmit Output Line signal.
0 - Indicates that the Transmit Section of Channel_n is NOT currently declaring the Transmit DMO Alarm condition.
1 - Indicates that the Transmit Section of Channel_n is currently declaring
the Transmit DMO Alarm condition.
74
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 31: XRT75R12D REGISTER MAP SHOWING TRANSMIT CONTROL REGISTERS (TC_N)
BIT 7
BIT 6
Reserved
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Internal
Transmit
Drive Monitor
Insert PRBS
Error
Reserved
TAOS
TxCLKINV
TxLEV
R/W
R/W
R/W
R/W
R/W
TRANSMIT CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM4
BIT NUMBER
NAME
TYPE
DESCRIPTION
7-6
Reserved
5
Internal Transmit
Drive Monitor
Enable
R/W
Internal Transmit Drive Monitor Enable - Channel_n:
This READ/WRITE bit-field is used to configure the Transmit Section of
Channel_n to either internally or externally monitor the TTIP_n and
TRING_n output pins for bipolar pulses, in order to determine whether to
declare the Transmit DMO Alarm condition.
If the user configures the Transmit Section to externally monitor the TTIP_n
and TRING_n output pins (for bipolar pulses) then the user must connect
the MTIP_n and MRING_n input pins to their corresponding TTIP_n and
TRING_n output pins (via a 270 ohm series resistor).
If the user configures the Transmit Section to internally monitor the TTIP_n
and TRING_n output pins (for bipolar pulses), the user does NOT need to
conect the MTIP_n and MRING_n input pins. This monitoring will be performed internally at the TTIP_n and TRING_n pads.
0 - Configures the Transmit Drive Monitor to externally monitor the TTIP_n
and TRING_n output pins for bipolar pulses.
1 - Configures the Transmit Drive Monitor to internally monitor the TTIP_n
and TRING_n output pins for bipolar pulses.
4
Insert PRBS Error
R/W
Insert PRBS Error - Channel_n:
A "0 to 1" transition within this bit-field causes the PRBS Generator (within
the Transmit Section of Channel_n) to generate a single bit error within the
outbound PRBS pattern-stream.
NOTES:
3
1.
This bit-field is only active if the PRBS Generator and Receiver
have been enabled within the corresponding Channel.
2.
After writing the "1" into this register, the user must execute a write
operation to clear this particular register bit to "0" in order to
facilitate the next "0 to 1" transition in this bit-field.
Reserved
75
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TRANSMIT CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM4
BIT NUMBER
NAME
TYPE
DESCRIPTION
2
TAOS
R/W
Transmit All OneS Pattern - Channel_n:
This READ/WRITE bit-field is used to command the Transmit Section of
Channel_n to generate and transmit an unframed, All Ones pattern via the
DS3, E3 or STS-1 line signal (to the remote terminal equipment).
Whenever the user implements this configuration setting, the Transmit Section will ignore the data that it is accepting from the System-side equipment
and output the "All Ones" Pattern.
0 - Configures the Transmit Section to transmit the data that it accepts from
the System-side Interface.
1 - Configures the Transmit Section to generate and transmit the Unframed,
All Ones pattern.
1
TxCLKINV
R/W
Transmit Clock Invert Select - Channel_n:
This READ/WRITE bit-field is used to select the edge of the TxCLK_n input
that the Transmit Section of Channel_n will use to sample the TxPOS_n and
TxNEG_n input pins, as described below.
0 - Configures the Transmit Section (within the corresponding channel) to
sample the TxPOS_n and TxNEG_n input pins upon the falling edge of
TxCLK_n.
1 - Configures the Transmit Section (within the corresponding channel) to
sample the TxPOS_n and TxNEG_n input pins upon the rising edge of
TxCLK_n.
NOTE: This is done on a per-channel basis.
0
TxLEV
R/W
Transmit Line Build-Out Select - Channel_n:
This READ/WRITE bit-field is used to enable or disable the Transmit Line
Build-Out (e.g., pulse-shaping) circuit within the corresponding channel.
The user should set this bit-field to either "0" or to "1" based upon the following guidelines.
0 - If the cable length between the Transmit Output (of the corresponding
Channel) and the DSX-3/STSX-1 location is 225 feet or less.
1 - If the cable length between the Transmit Output (of the corresponding
Channel) and the DSX-3/STSX-1 location is more than 225 feet .
The user must follow these guidelines in order to insure that the Transmit
Section (of Channel_n) will always generate a DS3 pulse that complies with
the Isolated Pulse Template requirements per Bellcore GR-499-CORE, or
an STS-1 pulse that complies with the Pulse Template requirements per Telcordia GR-253-CORE.
NOTE: This bit-field is ignored if the channel has been configured to operate
in the E3 Mode.
76
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 32: XRT75R12D REGISTER MAP SHOWING RECEIVE CONTROL REGISTERS (RC_N)
BIT 7
BIT 6
Reserved
BIT 5
BIT 4
Disable DLOS Disable ALOS
Detector
Detector
R/W
R/W
BIT 3
BIT 2
BIT 1
BIT 0
RxCLKINV
LOSMUT
Enable
Receive
Monitor Mode
Enable
Receive
Equalizer
Enable
R/W
R/W
R/W
R/W
RECEIVE CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM5
BIT NUMBER
NAME
7-6
Reserved
5
Disable DLOS
Detector
TYPE
R/W
DESCRIPTION
Disable Digital LOS Detector - Channel_n:
This READ/WRITE bit-field is used to enable or disable the Digital LOS
(Loss of Signal) Detector within Channel_n, as described below.
0 - Enables the Digital LOS Detector within Channel_n.
1 - Disables the Digital LOS Detector within Channel_n.
NOTE: This bit-field is only active if Channel_n has been configured to
operate in the DS3 or STS-1 Modes.
4
Disable ALOS
Detector
R/W
Disable Analog LOS Detector - Channel_n:
This READ/WRITE bit-field is used to either enable or disable the Analog
LOS (Loss of Signal) Detector within Channel_n, as described below.
0 - Enables the Analog LOS Detector within Channel_n.
1 - Disables the Analog LOS Detector within Channel_n.
NOTE: This bit-field is only active if Channel_n has been configured to
operate in the DS3 or STS-1 Modes.
3
RxCLKINV
R/W
Receive Clock Invert Select - Channel_n:
This READ/WRITE bit-field is used to select the edge of the RxCLK_n output that the Receive Section of Channel_n will use to output the recovered
data via the RxPOS_n and RxNEG_n output pins, as described below.
0 - Configures the Receive Section (within the corresponding channel) to
output the recovered data via the RxPOS_n and RxNEG_n output pins upon
the rising edge of RCLK_n.
1 - Configures the Receive Section (within the corresponding channel) to
output the recovered data via the RxPOS_n and RxNEG_n output pins upon
the falling edge of RCLK_n.
2
LOSMUT Enable
R/W
Muting upon LOS Enable - Channel_n:
This READ/WRITE bit-field is used to configure the Receive Section (within
Channel_n) to automatically pull their corresponding Recovered Data Output pins (e.g., RxPOS_n and RxNEG_n) to GND for the duration that the
Receive Section declares the LOS defect condition. In other words, this feature (if enabled) will cause the Receive Channel to automatically mute the
Recovered data anytime the Receive Section declares the LOS defect condition.
0 - Disables the Muting upon LOS feature. In this setting the Receive Section will NOT automatically mute the Recovered Data whenever it is declaring the LOS defect condition.
1 - Enables the Muting upon LOS feature. In this setting the Receive Section will automatically mute the Recovered Data whenever it is declaring the
LOS defect condition.
77
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
RECEIVE CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM5
BIT NUMBER
NAME
TYPE
DESCRIPTION
1
Receive Monitor
Mode Enable
R/W
Receive Monitor Mode Enable - Channel_n:
This READ/WRITE bit-field is used to configure the Receive Section of
Channel_n to operate in the Receive Monitor Mode.
If the user configures the Receive Section to operate in the Receive Monitor
Mode, then it will be able to receive a nominal DSX-3/STSX-1 signal that
has been attenuated by 20dB of flat loss along with 6dB of cable loss, in an
error-free manner. However, internal LOS circuitry is suppressed and LOS
will never assert nor LOS be declared when operating under this mode.
0 - Configures the corresponding channel to operate in the Normal Mode.
1 - Configure the corresponding channel to operate in the Receive Monitor
Mode.
0
Receive Equalizer
Enable
R/W
Receive Equalizer Enable - Channel_n:
This READ/WRITE register bit is used to enable or disable the Receive
Equalizer block within the Receive Section of Channel_n, as listed below.
0 - Disables the Receive Equalizer within the corresponding channel.
1 - Enables the Receive Equalizer within the corresponding channel.
NOTE: For virtually all applications, we recommend that the user set this bitfield to "1" (for all channels) and enable the Receive Equalizer.
78
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 33: XRT75R12D REGISTER MAP SHOWING CHANNEL CONTROL REGISTERS (CC_N)
BIT 7
BIT 6
Reserved
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
PRBS Enable
Ch_n
RLB_n
LLB_n
E3_n
STS-1/DS3_n
SR/DR_n
R/W
R/W
R/W
R/W
R/W
R/W
CHANNEL CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM6
BIT NUMBER
NAME
7-6
Reserved
5
PRBS Enable
TYPE
DESCRIPTION
R/W
PRBS Generator and Receiver Enable - Channel_n:
This READ/WRITE bit-field is used to enable or disable the PRBS Generator
and Receiver within a given Channel of the XRT75R12D.
If the user enables the PRBS Generator and Receiver, then the following will
happen.
1. The PRBS Generator (which resides within the Transmit Section of
the Channel) will begin to generate an unframed, 2^15-1 PRBS
Pattern (for DS3 and STS-1 applications) and an unframed, 2^23-1
PRBS Pattern (for E3 applications).
2. The PRBS Receiver (which resides within the Receive Section of the
Channel) will now be enabled and will begin to search the incoming
data for the above-mentioned PRBS patterns.
0 - Disables both the PRBS Generator and PRBS Receiver within the corresponding channel.
1 - Enables both the PRBS Generator and PRBS Receiver within the corresponding channel.
NOTES:
1.
To check and monitor PRBS Bit Errors, DR (Dual Rail) mode will be
over-ridden and Single Rail mode forced for the duration of this
mode. This will configure the RNEG/LCV_n output pin to function
as a PRBS Error Indicator. All errors will be flagged on this pin.
The errors will also be accumulated in the 16 bit Error counter for
the channel.
2.
If the user enables the PRBS Generator and PRBS Receiver, the
Channel will ignore the data that is being accepted from the
System-side Equipment (via the TxPOS_n and TxNEG_n input
pins) and will overwrite this outbound data with the PRBS Pattern.
3.
The system must provide an accurate and stable data-rate clock to
the TxClk_n pin during this operation.
79
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
CHANNEL CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM6
BIT NUMBER
NAME
TYPE
DESCRIPTION
4
RLB_n
R/W
Loop-Back Select - RLB Bit - Channel_n:
This READ/WRITE bit-field along with the corresponding LLB_n bit-field is
used to configure a given channel into various loop-back modes ass shown
by the following table.
LLB_n
RLB_n
Loop-back M ode
0
0
Norm al (No Loop-back) Mode
0
1
Rem ote Loop-back Mode
1
0
Analog Local Loop-back Mode
1
1
Digital Local Loop-back Mode
3
LLB_n
R/W
Loop-Back Select - LLB Bit-field - Channel_n:
See the table (above) for RLB_n.
2
E3_n
R/W
E3 Mode Select - Channel_n:
This READ/WRITE bit-field, along with Bit 1 (STS-1/DS3_n) within this register, is used to configure a given channel into either the DS3, E3 or STS-1
Modes.
0 - Configures Channel_n to operate in either the DS3 or STS-1 Modes,
depending upon the state of Bit 1 (STS-1/DS3_n) within this same register.
1- Configures Channel_n to operate in the E3 Mode.
80
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
CHANNEL CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM6
BIT NUMBER
NAME
TYPE
DESCRIPTION
1
STS-1/DS3_n
R/W
STS-1/DS3 Mode Select - Channel_n:
This READ/WRITE bit-field, along with Bit 2 (E3_n) is used to configure a
given channel into either the DS3, E3 or STS-1 Modes.
This bit-field is ignored if Bit 2 (E3_n) has been set to "1".
If Bit 2 (E3_n) is a 0:
0 - Configures Channel_n to operate in the DS3 Mode.
1 - Configures Channel_n to operate in the STS-1 Mode .
0
SR/DR_n
R/W
Single-Rail/Dual-Rail Select - Channel_n:
This READ/WRITE bit-field is used to configure Channel_n to operate in
either the Single-Rail or Dual-Rail Mode.
If the user configures the Channel to operate in the Single-Rail Mode, the
following will happen.
• The B3ZS/HDB3 Encoder and Decoder blocks (within Channel_n) will be
enabled.
• The Transmit Section of Channel_n will accept all of the outbound data
(from the System-side Equipment) via the TxPOS_n input pin.
• The Receive Section of each channel will output all of the recovered data
(to the System-side Equipment) via the RxPOS_n output pin.
• The corresponding RNEG/LCV_n output pin will now function as the LCV
(Line Code Violation or Excessive Zero Event) indicator output pin for
Channel_n.
If the user configures Channel_n to operate in the Dual-Rail Mode, the following will happen.
• The B3ZS/HDB3 Encoder and Decoder blocks of Channel_n will be
disabled.
• The Transmit Section of Channel_n will be configured to accept positivepolarity data via the TxPOS_n input pin and negative-polarity data via the
TxNEG_n input pin.
• The Receive Section of Channel_n will pulse the RxPOS_n output pin
"High" (for one period of RCLK_n) for each time a positive-polarity pulse is
received via the RTIP_n/RRING_n input pins. Likewise, the Receive
Section of each channel will pulse the RxNEG_n output pin "High" (for
one period of RxCLK_n) for each time a negative-polarity pulse is
received via the RTIP_n/RRING_n input pins.
0 - Configures Channel_n to operate in the Dual-Rail Mode.
1 - Configures Channel_n to operate in the Single-Rail Mode.
TABLE 34: XRT75R12D REGISTER MAP SHOWING JITTER ATTENUATOR CONTROL REGISTERS (JA_N)
BIT 7
BIT 6
BIT 5
BIT 4
Reserved
81
BIT 3
BIT 2
BIT 1
BIT 0
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/W
R/W
R/W
R/W
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL N ADDRESS LOCATION = 0XM7
BIT NUMBER
NAME
7-4
Reserved
3
JA RESET Ch_n
TYPE
DESCRIPTION
R/W
Jitter Attenuator RESET - Channel_n:
Writing a "0 to 1" transition within this bit-field will configure the Jitter Attenuator (within Channel_n) to execute a RESET operation.
Whenever the user executes a RESET operation, then following will occur.
• The READ and WRITE pointers (within the Jitter Attenuator FIFO) will be
reset to their default values.
• The contents of the Jitter Attenuator FIFO will be flushed.
NOTE: The user must follow up any "0 to 1" transition with the appropriate
write operate to set this bit-field back to "0", in order to resume
normal operation with the Jitter Attenuator.
2
JA1 Ch_n
R/W
Jitter Attenuator Configuration Select Input - Bit 1:
This READ/WRITE bit-field, along with Bit 0 (JA0 Ch_n) is used to do any of
the following.
• To enable or disable the Jitter Attenuator corresponding to Channel_n.
• To select the FIFO Depth for the Jitter Attenuator within Channel_n.
The relationship between the settings of these two bit-fields and the Enable/
Disable States, and FIFO Depths is presented below.
JA0
JA1
Jitter Attenuator M ode
0
0
FIFO Depth = 16 bits
0
1
FIFO Depth = 32 bits
1
0
Disabled
1
1
Disabled
1
JA in Tx Path Ch_n
R/W
Jitter Attenuator in Transmit/Receive Path Select Bit:
This input pin is used to configure the Jitter Attenuator (within Channel_n) to
operate in either the Transmit or Receive path, as described below.
0 - Configures the Jitter Attenuator (within Channel_n) to operate in the
Receive Path.
1 - Configures the Jitter Attenuator (within Channel_n) to operate in the
Transmit Path.
0
JA0 Ch_n
R/W
Jitter Attenuator Configuration Select Input - Bit 0:
See the description for Bit 2 (JA1 Ch_n).
TABLE 35: XRT75R12D REGISTER MAP SHOWING ERROR COUNTER MSBYTE REGISTERS (EM_N)
ADDRESS
LOCATION
0
1
2
3
4
5
6
7
8
0x0-
APST
IER0
ISR0
AS0
TC0
RC0
CC0
JA0
APSR
0X1-
IER1
ISR1
AS1
TC1
RC1
CC1
0x2-
IER2
ISR2
AS2
TC2
RC2
CC2
82
9
A
B
C
EM0
EL0
EH0
JA1
EM1
EL1
EH1
JA2
EM2
EL2
EH2
D E F
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
ADDRESS
LOCATION
1
2
3
4
5
6
7
0x3-
IER3
ISR3
AS3
TC3
RC3
CC3
0x4-
IER4
ISR4
AS4
TC4
RC4
0x5-
IER5
ISR5
AS5
TC5
RC5
0x6-
0
A
B
C
JA3
EM3
EL3
EH3
CC4
JA4
EM4
EL4
EH4
CC5
JA5
EM5
EL5
EH5
CIE
CIS
APST
IER6
ISR6
AS6
TC6
RC6
CC6
JA6
0X9-
IER7
ISR7
AS7
TC7
RC7
CC7
0xA-
IER8
ISR8
AS8
TC8
RC8
0xB-
IER9
ISR9
AS9
TC9
0xC-
IER10
ISR10
AS10
0xD-
IER11
ISR11
AS11
8
9
D E F
PN VN
0x70x8-
0xE-
CIE
EM6
EL6
EH6
JA7
EM7
EL7
EH7
CC8
JA8
EM8
EL8
EH8
RC9
CC9
JA9
EM9
EL9
EH9
TC10
RC10
CC10
JA10
EM10
EL10
EH10
TC11
RC11
CC11
JA11
EM11
EL11
EH11
APSR
CIS
0xF-
TABLE 36: ERROR COUNTER MSBYTE REGISTER - CHANNEL N ADDRESS LOCATION = 0XMA
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
Msb
9th bit
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
TABLE 37: XRT75R12D REGISTER MAP SHOWING ERROR COUNTER LSBYTE REGISTERS (EL_N)
ADDRESS
LOCATION
0
1
2
3
4
5
6
7
8
0x0-
APST
IER0
ISR0
AS0
TC0
RC0
CC0
JA0
APSR
0X1-
IER1
ISR1
AS1
TC1
RC1
CC1
0x2-
IER2
ISR2
AS2
TC2
RC2
0x3-
IER3
ISR3
AS3
TC3
0x4-
IER4
ISR4
AS4
0x5-
IER5
ISR5
AS5
0x6-
A
B
C
EM0
EL0
EH0
JA1
EM1
EL1
EH1
CC2
JA2
EM2
EL2
EH2
RC3
CC3
JA3
EM3
EL3
EH3
TC4
RC4
CC4
JA4
EM4
EL4
EH4
TC5
RC5
CC5
JA5
EM5
EL5
EH5
CIE
CIS
APST
IER6
ISR6
AS6
TC6
RC6
CC6
JA6
0X9-
IER7
ISR7
AS7
TC7
RC7
CC7
0xA-
IER8
ISR8
AS8
TC8
RC8
0xB-
IER9
ISR9
AS9
TC9
RC9
9
PN VN
0x70x8-
D E F
83
EM6
EL6
EH6
JA7
EM7
EL7
EH7
CC8
JA8
EM8
EL8
EH8
CC9
JA9
EM9
EL9
EH9
APSR
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 37: XRT75R12D REGISTER MAP SHOWING ERROR COUNTER LSBYTE REGISTERS (EL_N)
ADDRESS
LOCATION
1
2
3
4
5
6
7
0xC-
IER10
ISR10
AS10
TC10
RC10
CC10
JA10
EM10
EL10 EH10
0xD-
IER11
ISR11
AS11
TC11
RC11
CC11
JA11
EM11
EL11 EH11
0xE-
0
CIE
8
9
A
B
C
D E F
CIS
0xF-
TABLE 38: ERROR COUNTER LSBYTE REGISTER - CHANNEL N ADDRESS LOCATION = 0XMB
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
8th bit
Ls bit
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
TABLE 39: XRT75R12D REGISTER MAP SHOWING ERROR COUNTER HOLDING REGISTERS (EH_N)
ADDRESS
LOCATION
0
1
2
3
4
5
6
7
8
0x0-
APST
IER0
ISR0
AS0
TC0
RC0
CC0
JA0
APSR
0X1-
IER1
ISR1
AS1
TC1
RC1
CC1
0x2-
IER2
ISR2
AS2
TC2
RC2
0x3-
IER3
ISR3
AS3
TC3
0x4-
IER4
ISR4
AS4
0x5-
IER5
ISR5
AS5
0x6-
A
B
C
EM0
EL0
EH0
JA1
EM1
EL1
EH1
CC2
JA2
EM2
EL2
EH2
RC3
CC3
JA3
EM3
EL3
EH3
TC4
RC4
CC4
JA4
EM4
EL4
EH4
TC5
RC5
CC5
JA5
EM5
EL5
EH5
CIE
CIS
APST
IER6
ISR6
AS6
TC6
RC6
CC6
JA6
0X9-
IER7
ISR7
AS7
TC7
RC7
CC7
0xA-
IER8
ISR8
AS8
TC8
RC8
0xB-
IER9
ISR9
AS9
TC9
0xC-
IER10
ISR10
AS10
0xD-
IER11
ISR11
AS11
9
0xE-
CIE
E F
PN VN
0x70x8-
D
EM6
EL6
EH6
JA7
EM7
EL7
EH7
CC8
JA8
EM8
EL8
EH8
RC9
CC9
JA9
EM9
EL9
EH9
TC10
RC10
CC10
JA1
0
EM10 EL10
EH10
TC11
RC11
CC11 JA11
EM11 EL11
EH11
CIS
0xF-
84
APSR
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 40: ERROR COUNTER HOLDING REGISTER - CHANNEL N ADDRESS LOCATION = 0XMC
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
Msb
R/W
BIT 0
Ls bit
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Each channel contains a dedicated 16 bit PRBS error counter. When enabled this counter will accumulate
PRBS errors (as well as excess zeros and LCVs). The LS byte will "carry" a one over to the MS byte each time
it rolls over from 255 to zero until the MS byte also reaches 255. When both counters reach 255, no further
errors will be accumulated and "all ones" will signify an overflow condition.
The counter can be read while in the active count mode. Either register may be read "on the fly" and the other
byte will be simultaneously transferred into the channel’s Error Holding register. The holding register may then
be read to supply the Host with a correct 16 bit count (as of the instant of reading). With this mechanism, the
Host could rapidly cycle thru reading all twelve counters in order (storing the read byte in scratch RAM) and
then come back and read the second byte from each holding register to form the 16 bit accumulation in the
Host system.
85
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
8.0 THE SONET/SDH DE-SYNC FUNCTION WITHIN THE LIU
The LIU with D-SYNC is very similar to the non D-SYNC LIU in that they both contain Jitter Attenuator blocks
within each channel. They are also pin to pin compatible with each other. However, the Jitter Attenuators
within the D-SYNC have some enhancements over and above those within the non D-SYNC device. The Jitter
Attenuator blocks will support all of the modes and features that exist in the non D-SYNC device and in
addition they also support a SONET/SDH De-Sync Mode.
NOTE: The "D" suffix within the part number stands for "De-Sync".
The SONET/SDH De-Sync feature of the Jitter Attenuator blocks permits the user to design a SONET/SDH
PTE (Path Terminating Equipment) that will comply with all of the following Intrinsic Jitter and Wander
requirements.
• For SONET Applications
■
Category I Intrinsic Jitter Requirements per Telcordia GR-253-CORE (for DS3 Applications)
■
ANSI T1.105.03b-1997 - SONET Jitter at Network Interfaces - DS3 Wander Supplement
• For SDH Applications
■
Jitter and Wander Generation Requirements per ITU-T G.783 (for DS3 and E3 Applications)
Specifically, if the user designs in the LIU along with a SONET/SDH Mapper IC (which can be realized as either
a standard product or as a custom logic solution, in an ASIC or FPGA), then the following can be
accomplished.
• The Mapper can receive an STS-N or an STM-M signal (which is carrying asynchronously-mapped DS3 and/
or E3 signals) and byte de-interleave this data into N STS-1 or 3*M VC-3 signals
• The Mapper will then terminate these STS-1 or VC-3 signals and will de-map out this DS3 or E3 data from
the incoming STS-1 SPEs or VC-3s, and output this DS3 or E3 to the DS3/E3 Facility-side towards the LIU
• This DS3 or E3 signal (as it is output from these Mapper devices) will contain a large amount of intrinsic jitter
and wander due to (1) the process of asynchronously mapping a DS3 or E3 signal into a SONET or SDH
signal, (2) the occurrence of Pointer Adjustments within the SONET or SDH signal (transporting these DS3
or E3 signals) as it traverses the SONET/SDH network, and (3) clock gapping.
• When the LIU has been configured to operate in the "SONET/SDH De-Sync" Mode, then it will (1) accept this
jittery DS3 or E3 clock and data signal from the Mapper device (via the Transmit System-side interface) and
(2) through the Jitter Attenuator, the LIU will reduce the Jitter and Wander amplitude within these DS3 or E3
signals such that they (when output onto the line) will comply with the above-mentioned intrinsic jitter and
wander specifications.
8.1
BACKGROUND AND DETAILED INFORMATION - SONET DE-SYNC APPLICATIONS
This section provides an in-depth discussion on the mechanisms that will cause Jitter and Wander within a
DS3 or E3 signal that is being transported across a SONET or SDH Network. A lot of this material is
introductory, and can be skipped by the engineer that is already experienced in SONET/SDH designs.
In the wide-area network (WAN) in North America it is often necessary to transport a DS3 signal over a long
distance (perhaps over a thousand miles) in order to support a particular service. Now rather than realizing
this transport of DS3 data, by using over a thousand miles of coaxial cable (interspaced by a large number of
DS3 repeaters) a common thing to do is to route this DS3 signal to a piece of equipment (such as a Terminal
MUX, which in the "SONET Community" is known as a PTE or Path Terminating Equipment). This Terminal
MUX will asynchronously map the DS3 signal into a SONET signal. At this point, the SONET network will now
transport this asynchronously mapped DS3 signal from one PTE to another PTE (which is located at the other
end of the SONET network). Once this SONET signal arrives at the remote PTE, this DS3 signal will then be
extracted from the SONET signal, and will be output to some other DS3 Terminal Equipment for further
processing.
Similar things are done outside of North America. In this case, this DS3 or E3 signal is routed to a PTE, where
it is asynchronously mapped into an SDH signal. This asynchronously mapped DS3 or E3 signal is then
86
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
transported across the SDH network (from one PTE to the PTE at the other end of the SDH network). Once
this SDH signal arrives at the remote PTE, this DS3 or E3 signal will then be extracted from the SDH signal,
and will be output to some other DS3/E3 Terminal Equipment for further processing.
Figure 37 presents an illustration of this approach to transporting DS3 data over a SONET Network
FIGURE 37. A SIMPLE ILLUSTRATION OF A DS3 SIGNAL BEING MAPPED INTO AND TRANSPORTED OVER THE SONET
NETWORK
SONET
Network
DS3 Data
PTE
PTE
PTE
PTE
DS3 Data
As mentioned above a DS3 or E3 signal will be asynchronously mapped into a SONET or SDH signal and then
transported over the SONET or SDH network. At the remote PTE this DS3 or E3 signal will be extracted (or
de-mapped) from this SONET or SDH signal, where it will then be routed to DS3 or E3 terminal equipment for
further processing.
In order to insure that this "de-mapped" DS3 or E3 signal can be routed to any industry-standard DS3 or E3
terminal equipment, without any complications or adverse effect on the network, the Telcordia and ITU-T
standard committees have specified some limits on both the Intrinsic Jitter and Wander that may exist within
these DS3 or E3 signals as they are de-mapped from SONET/SDH. As a consequence, all PTEs that maps
and de-mapped DS3/E3 signals into/from SONET/SDH must be designed such that the DS3 or E3 data that is
de-mapped from SONET/SDH by these PTEs must meet these Intrinsic Jitter and Wander requirements.
As mentioned above, the LIU can assist the System Designer (of SONET/SDH PTE) by ensuring that their
design will meet these Intrinsic Jitter and Wander requirements.
This section of the data sheet will present the following information to the user.
• Some background information on Mapping DS3/E3 signals into SONET/SDH and de-mapping DS3/E3
signals from SONET/SDH.
• A brief discussion on the causes of jitter and wander within a DS3 or E3 signal that mapped into a SONET/
SDH signal, and is transported across the SONET/SDH Network.
• A brief review of these Intrinsic Jitter and Wander requirements in both SONET and SDH applications.
• A brief review on the Intrinsic Jitter and Wander measurement results (of a de-mapped DS3 or E3 signal)
whenever the LIU device is used in a system design.
87
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
• A detailed discussion on how to design with and configure the LIU device such that the end-system will meet
these Intrinsic Jitter and Wander requirements.
In a SONET system, the relevant specification requirements for Intrinsic Jitter and Wander (within a DS3 signal
that is mapped into and then de-mapped from SONET) are listed below.
• Telcordia GR-253-CORE Category I Intrinsic Jitter Requirements for DS3 Applications (Section 5.6), and
• ANSI T1.105.03b-1997 - SONET Jitter at Network Interfaces - DS3 Wander Supplement
In general, there are three (3) sources of Jitter and Wander within an asynchronously-mapped DS3 signal that
the system designer must be aware of. These sources are listed below.
• Mapping/De-Mapping Jitter
• Pointer Adjustments
• Clock Gapping
Each of these sources of jitter/wander will be defined and discussed in considerable detail within this Section.
In order to accomplish all of this, this particular section will discuss all of the following topics in details.
• How DS3 data is mapped into SONET, and how this mapping operation contributes to Jitter and Wander
within this "eventually de-mapped" DS3 signal.
• How this asynchronously-mapped DS3 data is transported throughout the SONET Network, and how
occurrences on the SONET network (such as pointer adjustments) will further contributes to Jitter and
Wander within the "eventually de-mapped" DS3 signal.
• A review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3 applications
• A review of the DS3 Wander requirements per ANSI T1.105.03b-1997
• A review of the Intrinsic Jitter and Wander Capabilities of the LIU in a typical system application
• An in-depth discussion on how to design with and configure the LIU to permit the system to the meet the
above-mentioned Intrinsic Jitter and Wander requirements
NOTE: An in-depth discussion on SDH De-Sync Applications will be presented in the next revision of this data sheet.
8.2
MAPPING/DE-MAPPING JITTER/WANDER
Mapping/De-Mapping Jitter (or Wander) is defined as that intrinsic jitter (or wander) that is induced into a DS3
signal by the "Asynchronous Mapping" process. This section will discuss all of the following aspects of
Mapping/De-Mapping Jitter.
• How DS3 data is mapped into an STS-1 SPE
• How frequency offsets within either the DS3 signal (being mapped into SONET) or within the STS-1 signal
itself contributes to intrinsic jitter/wander within the DS3 signal (being transported via the SONET network).
8.2.1
HOW DS3 DATA IS MAPPED INTO SONET
Whenever a DS3 signal is asynchronously mapped into SONET, this mapping is typically accomplished by a
PTE accepting DS3 data (from some remote terminal) and then loading this data into certain bit-fields within a
given STS-1 SPE (or Synchronous Payload Envelope). At this point, this DS3 signal has now been
asynchronously mapped into an STS-1 signal. In most applications, the SONET Network will then take this
particular STS-1 signal and will map it into "higher-speed" SONET signals (e.g., STS-3, STS-12, STS-48, etc.)
and will then transport this asynchronously mapped DS3 signal across the SONET network, in this manner. As
this "asynchronously-mapped" DS3 signal approaches its "destination" PTE, this STS-1 signal will eventually
be de-mapped from this STS-N signal. Finally, once this STS-1 signal reaches the "destination" PTE, then this
asynchronously-mapped DS3 signal will be extracted from this STS-1 signal.
8.2.1.1
A Brief Description of an STS-1 Frame
88
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
In order to be able to describe how a DS3 signal is asynchronously mapped into an STS-1 SPE, it is important
to define and understand all of the following.
• The STS-1 frame structure
• The STS-1 SPE (Synchronous Payload Envelope)
• Telcordia GR-253-CORE's recommendation on mapping DS3 data into an STS-1 SPE
An STS-1 frame is a data-structure that consists of 810 bytes (or 6480 bits). A given STS-1 frame can be
viewed as being a 9 row by 90 byte column array (making up the 810 bytes). The frame-repetition rate (for an
STS-1 frame) is 8000 frames/second. Therefore, the bit-rate for an STS-1 signal is (6480 bits/frame * 8000
frames/sec =) 51.84Mbps.
A simple illustration of this SONET STS-1 frame is presented below in Figure 38.
FIGURE 38. A SIMPLE ILLUSTRATION OF THE SONET STS-1 FRAME
90 Bytes
9 Rows
STS-1 Frame (810 Bytes)
Last Byte of the STS-1 Frame
First Byte of the STS-1 Frame
Figure 38 indicates that the very first byte of a given STS-1 frame (to be transmitted or received) is located in
the extreme upper left hand corner of the 90 column by 9 row array, and that the very last byte of a given STS1 frame is located in the extreme lower right-hand corner of the frame structure. Whenever a Network Element
transmits a SONET STS-1 frame, it starts by transmitting all of the data, residing within the top row of the STS1 frame structure (beginning with the left-most byte, and then transmitting the very next byte, to the right). After
the Network Equipment has completed its transmission of the top or first row, it will then proceed to transmit the
second row of data (again starting with the left-most byte, first). Once the Network Equipment has transmitted
the last byte of a given STS-1 frame, it will proceed to start transmitting the very next STS-1 frame.
The illustration of the STS-1 frame (in Figure 38) is very simplistic, for multiple reasons. One major reason is
that the STS-1 frame consists of numerous types of bytes. For the sake of discussion within this data sheet,
the STS-1 frame will be described as consisting of the following types (or groups) of bytes.
• The Transport Overheads (or TOH) Bytes
• The Envelope Capacity Bytes
8.2.1.1.1
The Transport Overhead (TOH) Bytes
The Transport Overhead or TOH bytes occupy the very first three (3) byte columns within each STS-1 frame.
Figure 39 presents another simple illustration of an STS-1 frame structure. However, in this case, both the
TOH and the Envelope Capacity bytes are designated in this Figure.
89
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 39. A SIMPLE ILLUSTRATION OF THE STS-1 FRAME STRUCTURE WITH THE TOH AND THE ENVELOPE
CAPACITY BYTES DESIGNATED
90 Bytes
3 Bytes
TOH
87 Bytes
Envelope Capacity
9 Row
Since the TOH bytes occupy the first three byte columns of each STS-1 frame, and since each STS-1 frame
consists of nine (9) rows, then we can state that the TOH (within each STS-1 frame) consists of 3 byte columns
x 9 rows = 27 bytes. The byte format of the TOH is presented below in Figure 40.
90
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 40. THE BYTE-FORMAT OF THE TOH WITHIN AN STS-1 FRAME
3 Byte Columns
9 Rows
87 Byte Columns
A1
A1
B1
B1
A2
A2
E1
E1
C1
C1
F1
F1
D1
D1
H1
H1
D2
D2
H2
H2
D3
D3
H3
H3
B2
B2
D4
D4
K1
K1
D5
D5
K2
K2
D6
D6
D7
D7
D10
D10
D8
D8
D11
D11
D9
D9
D12
D12
S1
S1
M0
M0
E2
E2
Envelope
EnvelopeCapacity
Capacity
Bytes
Bytes
The TOH Bytes
In general, the role/purpose of the TOH bytes is to fulfill the following functions.
• To support STS-1 Frame Synchronization
• To support Error Detection within the STS-1 frame
• To support the transmission of various alarm conditions such as RDI-L (Line - Remote Defect Indicator) and
REI-L (Line - Remote Error Indicator)
• To support the Transmission and Reception of "Section Trace" Messages
• To support the Transmission and Reception of OAM&P Messages via the DCC Bytes (Data Communication
Channel bytes - D1 through D12 byte)
The roles of most of the TOH bytes is beyond the scope of this Data Sheet and will not be discussed any
further. However, there are a three TOH bytes that are important from the stand-point of this data sheet, and
will discussed in considerable detail throughout this document. These are the H1 and H2 (e.g., the SPE
Pointer) bytes and the H3 (e.g., the Pointer Action) byte.
Figure 41 presents an illustration of the Byte-Format of the TOH within an STS-1 Frame, with the H1, H2 and
H3 bytes highlighted.
91
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 41. THE BYTE-FORMAT OF THE TOH WITHIN AN STS-1 FRAME
3 Byte Columns
9 Rows
87 Byte Columns
A1
A1
B1
B1
A2
A2
E1
E1
C1
C1
F1
F1
D1
D1
H1
H1
D2
D2
H2
H2
D3
D3
H3
H3
B2
B2
K1
K1
K2
K2
D4
D4
D7
D7
D5
D5
D8
D8
D6
D6
D9
D9
D10
D10
S1
S1
D11
D11
M0
M0
D12
D12
E2
E2
Envelope
EnvelopeCapacity
Capacity
Bytes
Bytes
The TOH Bytes
Although the role of the H1, H2 and H3 bytes will be discussed in much greater detail in “Section 8.3, Jitter/
Wander due to Pointer Adjustments” on page 99. For now, we will simply state that the role of these bytes
is two-fold.
• To permit a given PTE (Path Terminating Equipment) that is receiving an STS-1 data to be able to locate the
STS-1 SPE (Synchronous Payload Envelope) within the Envelope Capacity of this incoming STS-1 data
stream and,
• To inform a given PTE whenever Pointer Adjustment and NDF (New Data Flag) events occur within the
incoming STS-1 data-stream.
8.2.1.1.2
The Envelope Capacity Bytes within an STS-1 Frame
In general, the Envelope Capacity Bytes are any bytes (within an STS-1 frame) that exist outside of the TOH
bytes. In short, the Envelope Capacity contains the STS-1 SPE (Synchronous Payload Envelope). In fact,
every single byte that exists within the Envelope Capacity also exists within the STS-1 SPE. The only
difference that exists between the "Envelope Capacity" as defined in Figure 40 and Figure 41 above and the
STS-1 SPE is that the Envelope Capacity is aligned with the STS-1 framing boundaries and the TOH bytes;
whereas the STS-1 SPE is NOT aligned with the STS-1 framing boundaries, nor the TOH bytes.
The STS-1 SPE is an "87 byte column x 9 row" data-structure (which is the exact same size as is the Envelope
Capacity) that is permitted to "float" within the "Envelope Capacity". As a consequence, the STS-1 SPE (within
an STS-1 data-stream) will typically straddle across an STS-1 frame boundary.
8.2.1.1.3
The Byte Structure of the STS-1 SPE
As mentioned above, the STS-1 SPE is an 87 byte column x 9 row structure. The very first column within the
STS-1 SPE consists of some overhead bytes which are known as the "Path Overhead" (or POH) bytes. The
remaining portions of the STS-1 SPE is available for "user" data. The Byte Structure of the STS-1 SPE is
presented below in Figure 42.
92
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 42. ILLUSTRATION OF THE BYTE STRUCTURE OF THE STS-1 SPE
87 Bytes
1 Byte
9 Rows
J1
B3
C2
G1
F2
H4
Z3
Z4
Z5
86 Bytes
Payload (or User) Data
In general, the role/purpose of the POH bytes is to fulfill the following functions.
• To support error detection within the STS-1 SPE
• To support the transmission of various alarm conditions such as RDI-P (Path - Remote Defect Indicator) and
REI-P (Path - Remote Error Indicator)
• To support the transmission and reception of "Path Trace" Messages
The role of the POH bytes is beyond the scope of this data sheet and will not be discussed any further.
8.2.1.2
Mapping DS3 data into an STS-1 SPE
Now that we have defined the STS-1 SPE, we can now describe how a DS3 signal is mapped into an STS-1
SPE. As mentioned above, the STS-1 SPE is basically an 87 byte column x 9 row structure of data. The very
first byte column (e.g., in all 9 bytes) consists of the POH (Path Overhead) bytes. All of the remaining bytes
within the STS-1 SPE is simply referred to as "user" or "payload" data because this is the portion of the STS-1
signal that is used to transport "user data" from one end of the SONET network to the other. Telcordia GR-253CORE specifies the approach that one must use to asynchronously map DS3 data into an STS-1 SPE. In
short, this approach is presented below in Figure 43.
93
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 43. AN ILLUSTRATION OF TELCORDIA GR-253-CORE'S RECOMMENDATION ON HOW MAP DS3 DATA INTO
AN STS-1 SPE
• For DS3 Mapping, the STS-1 SPE has the following structure.
87 bytes
POH
R
R
C1
25I
R
C2
I
25I
R
C3
I
25I
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
C1
C1
C1
C1
C1
C1
C1
C1
25I
25I
25I
25I
25I
25I
25I
25I
R
R
R
R
R
R
R
R
C2
C2
C2
C2
C2
C2
C2
C2
I
I
I
I
I
I
I
I
25I
25I
25I
25I
25I
25I
25I
25I
R
R
R
R
R
R
R
R
C3
C3
C3
C3
C3
C3
C3
C3
I
I
I
I
I
I
I
I
25I
25I
25I
25I
25I
25I
25I
25I
i = DS3 data
I = [i, i, i, i, i, i, i, i]
R = [r, r, r, r, r, r, r, r]
r = fixed stuff bit
Fixed
Stuff
C1 = [r, r, c, i, i, i, i, i]
c = stuff control bit
C2 = [c, c, r, r, r, r, r, r]
s = stuff opportunity bit
C3 = [c, c, r, r, o, o, r, s]
o = overhead communications channel bit
Figure 43 was copied directly out of Telcordia GR-253-CORE. However, this figure can be simplified and
redrawn as depicted below in Figure 44.
FIGURE 44. A SIMPLIFIED "BIT-ORIENTED" VERSION OF TELCORDIA GR-253-CORE'S RECOMMENDATION ON HOW
TO MAP DS3 DATA INTO AN STS-1 SPE
POH
18r
c
205i
16r
2c
6r
208i
16r
2c
2r
2o
1r
s
208i
18r
18r
c
c
205i
205i
16r
16r
2c
2c
6r
6r
208i
208i
16r
16r
2c
2c
2r
2r
2o
2o
1r
1r
s
s
208i
208i
18r
18r
18r
c
c
c
205i
205i
205i
16r
16r
16r
2c
2c
2c
6r
6r
6r
208i
208i
208i
16r
16r
16r
2c
2c
2c
2r
2r
2r
2o
2o
2o
1r
1r
1r
s
s
s
208i
208i
208i
18r
18r
c
c
205i
205i
16r
16r
2c
2c
6r
6r
208i
208i
16r
16r
2c
2c
2r
2r
2o
2o
1r
1r
s
s
208i
208i
18r
c
205i
16r
2c
6r
208i
16r
2c
2r
2o
1r
s
208i
r
- Fixed Stuff Bits
c
- Stuff Control/Indicator Bits
i
- DS3 Data Bits
s
- Stuff Opportunity Bits
o
94
- Overhead Communication Bits
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
Figure 44 presents an alternative illustration of Telcordia GR-253-CORE's recommendation on how to
asynchronously map DS3 data into an STS-1 SPE. In this case, the STS-1 SPE bit-format is expressed purely
in the form of "bit-types" and "numbers of bits within each of these types of bits". If one studies this figure
closely he/she will notice that this is the same "87 byte column x 9 row" structure that we have been talking
about when defining the STS-1 SPE. However, in this figure, the "user-data" field is now defined and is said to
consist of five (5) different types of bits. Each of these bit-types play a role when asynchronously mapping a
DS3 signal into an STS-1 SPE. Each of these types of bits are listed and described below.
Fixed Stuff Bits
Fixed Stuff bits are simply "space-filler" bits that simply occupy space within the STS-1 SPE. These bit-fields
have no functional role other than "space occupation". Telcordia GR-253-CORE does not define any particular
value that these bits should be set to. Each of the 9 rows, within the STS-1 SPE will contain 59 of these "fixed
stuff" bits.
DS3 Data Bits
The DS3 Data-Bits are (as its name implies) used to transport the DS3 data-bits within the STS-1 SPE. If the
STS-1 SPE is transporting a framed DS3 data-stream, then these DS3 Data bits will carry both the "DS3
payload data" and the "DS3 overhead bits". Each of the 9 rows, within the STS-1 SPE will contain 621 of these
"DS3 Data bits". This means that each STS-1 SPE contains 5,589 of these DS3 Data bit-fields.
Stuff Opportunity Bits
The "Stuff" Opportunity bits will function as either a "stuff" (or junk) bit, or it will carry a DS3 data-bit. The
decision as to whether to have a "Stuff Opportunity" bit transport a "DS3 data-bit" or a "stuff" bit depends upon
the "timing differences" between the DS3 data that is being mapped into the STS-1 SPE and the timing source
that is driving the STS-1 circuitry within the PTE.
As will be described later on, these "Stuff Opportunity" Bits play a very important role in "frequency-justifying"
the DS3 data that is being mapped into the STS-1 SPE. These "Stuff Opportunity" bits also play a critical role
in inducing Intrinsic Jitter and Wander within the DS3 signal (as it is de-mapped by the remote PTE).
Each of the 9 rows, within the STS-1 SPE consists of one (1) Stuff Opportunity bit. Hence, there are a total of
nine "Stuff Opportunity" bits within each STS-1 SPE.
Stuff Control/Indicator Bits
Each of the nine (9) rows within the STS-1 SPE contains five (5) Stuff Control/Indicator bits. The purpose of
these "Stuff Control/Indicator" bits is to indicate (to the de-mapping PTE) whether the "Stuff Opportunity" bits
(that resides in the same row) is a "Stuff" bit or is carrying a DS3 data bit.
If all five of these "Stuff Control/Indicator" bits, within a given row are set to "0", then this means that the
corresponding "Stuff Opportunity" bit (e.g., the "Stuff Opportunity" bit within the same row) is carrying a DS3
data bit.
Conversely, if all five of these "Stuff Control/Indicator" bits, within a given row are set to "1" then this means that
the corresponding "Stuff Opportunity" bit is carrying a "stuff" bit.
Overhead Communication Bits
Telcordia GR-253-CORE permits the user to use these two bits (for each row) as some sort of
"Communications" bit. Some Mapper devices, such as the XRT94L43 12-Channel DS3/E3/STS-1 to STS-12/
STM-1 Mapper and the XRT94L33 3-Channel DS3/E3/STS-1 to STS-3/STM-1 Mapper IC (both from Exar
Corporation) do permit the user to have access to these bit-fields.
However, in general, these particular bits can also be thought of as "Fixed Stuff" bits, that mostly have a "space
occupation" function.
8.2.2
DS3 Frequency Offsets and the Use of the "Stuff Opportunity" Bits
In order to fully convey the role that the "stuff-opportunity" bits play, when mapping DS3 data into SONET, we
will present a detailed discussion of each of the following "Mapping DS3 into STS-1" scenarios.
95
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
• The Ideal Case (e.g., with no frequency offsets)
• The 44.736Mbps + 1 ppm Case
• The 44.736MHz - 1ppm Case
Throughout each of these cases, we will discuss how the resulting "bit-stuffing" (that was done when mapping
the DS3 signal into SONET) affects the amount of intrinsic jitter and wander that will be present in the DS3
signal, once it is ultimately de-mapped from SONET.
8.2.2.1
The Ideal Case for Mapping DS3 data into an STS-1 Signal (e.g., with no Frequency
Offsets)
Let us assume that we are mapping a DS3 signal, which has a bit rate of exactly 44.736Mbps (with no
frequency offset) into SONET. Further, let us assume that the SONET circuitry within the PTE is clocked at
exactly 51.84MHz (also with no frequency offset), as depicted below.
FIGURE 45. A SIMPLE ILLUSTRATION OF A DS3 DATA-STREAM BEING MAPPED INTO AN STS-1 SPE, VIA A PTE
STS-1_Data_Out
DS3_Data_In
PTE
PTE
51.84MHz + 0ppm
44.736MHz + 0ppm
Given the above-mentioned assumptions, we can state the following.
• The DS3 data-stream has a bit-rate of exactly 44.736Mbps
• The PTE will create 8000 STS-1 SPE's per second
• In order to properly map a DS3 data-stream into an STS-1 data-stream, then each STS-1 SPE must carry
(44.736Mbps/8000 =) 5592 DS3 data bits.
Is there a Problem?
According to Figure 44, each STS-1 SPE only contains 5589 bits that are specifically designated for "DS3 data
bits". In this case, each STS-1 SPE appears to be three bits "short".
No there is a Simple Solution
No, earlier we mentioned that each STS-1 SPE consists of nine (9) "Stuff Opportunity" bits. Therefore, these
three additional bits (for DS3 data) are obtained by using three of these "Stuff Opportunity" bits. As a
consequence, three (3) of these nine (9) "Stuff Opportunity" bits, within each STS-1 SPE, will carry DS3 databits. The remaining six (6) "Stuff Opportunity" bits will typically function as "stuff" bits.
In summary, for the "Ideal Case"; where there is no frequency offset between the DS3 and the STS-1 bit-rates,
once this DS3 data-stream has been mapped into the STS-1 data-stream, then each and every STS-1 SPE will
have the following "Stuff Opportunity" bit utilization.
3 "Stuff Opportunity" bits will carry DS3 data bits.
6 "Stuff Opportunity" bits will function as "stuff" bits
96
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
In this case, this DS3 signal (which has now been mapped into STS-1) will be transported across the SONET
network. As this STS-1 signal arrives at the "Destination PTE", this PTE will extract (or de-map) this DS3 datastream from each incoming STS-1 SPE. Now since each and every STS-1 SPE contains exactly 5592 DS3
data bits; then the bit rate of this DS3 signal will be exactly 44.736Mbps (such as it was when it was mapped
into SONET, at the "Source" PTE).
As a consequence, no "Mapping/De-Mapping" Jitter or Wander is induced in the "Ideal Case".
8.2.2.2
The 44.736Mbps + 1ppm Case
The "above example" was a very ideal case. In reality, there are going to be frequency offsets in both the DS3
and STS-1 signals. For instance Bellcore GR-499-CORE mandates that a DS3 signal have a bit rate of
44.736Mbps ± 20ppm. Hence, the bit-rate of a "Bellcore" compliant DS3 signal can vary from the exact correct
frequency for DS3 by as much of 20ppm in either direction. Similarly, many SONET applications mandate that
SONET equipment use at least a "Stratum 3" level clock as its timing source. This requirement mandates that
an STS-1 signal must have a bit rate that is in the range of 51.84 ± 4.6ppm. To make matters worse, there are
also provisions for SONET equipment to use (what is referred to as) a "SONET Minimum Clock" (SMC) as its
timing source. In this case, an STS-1 signal can have a bit-rate in the range of 51.84Mbps ± 20ppm.
In order to convey the impact that frequency offsets (in either the DS3 or STS-1 signal) will impose on the bitstuffing behavior, and the resulting bit-rate, intrinsic jitter and wander within the DS3 signal that is being
transported across the SONET network; let us assume that a DS3 signal, with a bit-rate of 44.736Mbps +
1ppm is being mapped into an STS-1 signal with a bit-rate of 51.84Mbps + 0ppm. In this case, the following
things will occur.
• In general, most of the STS-1 SPE's will each transport 5592 DS3 data bits.
• However, within a "one-second" period, a DS3 signal that has a bit-rate of 44.736Mbps + 1 ppm will deliver
approximately 44.7 additional bits (over and above that of a DS3 signal with a bit-rate of 44.736Mbps + 0
ppm). This means that this particular signal will need to "negative-stuff" or map in an additional DS3 data bit
every (1/44.736 =) 22.35ms. In other words, this additional DS3 data bit will need to be mapped into about
one in every (22.35ms · 8000 =) 178.8 STS-1 SPEs in order to avoid dropping any DS3 data-bits.
What does this mean at the "Source" PTE?
All of this means that as the "Source" PTE maps this DS3 signal, with a data rate of 44.736Mbps + 1ppm into
an STS-1 signal, most of the resulting "outbound" STS-1 SPEs will transport 5592 DS3 data bits (e.g., 3 Stuff
Opportunity bits will be carrying DS3 data bits, the remaining 6 Stuff Opportunity bits are "stuff" bits, as in the
"Ideal" case). However, in approximately one out of 178.8 "outbound" STS-1 SPEs, there will be a need to
insert an additional DS3 data bit within this STS-1 SPE. Whenever this occurs, then (for these particular STS1 SPEs) the SPE will be carrying 5593 DS3 data bits (e.g., 4 Stuff Opportunity bits will be carrying DS3 data
bits, the remaining 5 Stuff Opportunity bits are "stuff" bits).
Figure 46 presents an illustration of the STS-1 SPE traffic that will be generated by the "Source" PTE, during
this condition.
97
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 46. AN ILLUSTRATION OF THE STS-1 SPE TRAFFIC THAT WILL BE GENERATED BY THE "SOURCE" PTE,
WHEN MAPPING IN A DS3 SIGNAL THAT HAS A BIT RATE OF 44.736MBPS + 1PPM, INTO AN STS-1 SIGNAL
Extra DS3 Data
Bit Stuffed Here
SPE # N
Source
Source
PTE
PTE
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+1
SPE # N+177
5592
5592
DS3
DS3Data
Data
Bits
Bits
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+179
5593
5593
DS3
DS3Data
Data
Bits
Bits
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+178
44.736Mbps + 1ppm
STS-1 SPE Data Stream
What does this mean at the "Destination" PTE?
In this case, this DS3 signal (which has now been mapped into an STS-1 data-stream) will be transported
across the SONET network. As this STS-1 signal arrives at the "Destination" PTE, this PTE will extract (or demap) this DS3 data from each incoming STS-1 SPE. Now, in this case most (e.g., 177/178.8) of the incoming
STS-1 SPEs will contain 5592 DS3 data-bits. Therefore, the nominal data rate of the DS3 signal being demapped from SONET will be 44.736Mbps. However, in approximately 1 out of every 178 incoming STS-1
SPEs, the SPE will carry 5593 DS3 data-bits. This means that (during these times) the data rate of the demapped DS3 signal will have an instantaneous frequency that is greater than 44.736Mbps. These "excursion"
of the de-mapped DS3 data-rate, from the nominal DS3 frequency can be viewed as occurrences of "mapping/
de-mapping" jitter. Since each of these "bit-stuffing" events involve the insertion of one DS3 data bit, we can
say that the amplitude of this "mapping/de-mapping" jitter is approximately 1UI-pp. From this point on, we will
be referring to this type of jitter (e.g., that which is induced by the mapping and de-mapping process) as "demapping" jitter.
Since this occurrence of "de-mapping" jitter is periodic and occurs once every 22.35ms, we can state that this
jitter has a frequency of 44.7Hz.
8.2.2.3
The 44.736Mbps - 1ppm Case
In this case, let us assume that a DS3 signal, with a bit-rate of 44.736Mbps - 1ppm is being mapped into an
STS-1 signal with a bit-rate of 51.84Mbps + 0ppm. In this case, the following this will occur.
• In general, most of the STS-1 SPEs will each transport 5592 DS3 data bits.
• However, within a "one-second" period a DS3 signal that has a bit-rate of 44.736Mbps - 1ppm will deliver
approximately 45 too few bits below that of a DS3 signal with a bit-rate of 44.736Mbps + 0ppm. This means
that this particular signal will need to "positive-stuff" or exclude a DS3 data bit from mapping every (1/44.736)
= 22.35ms. In other words, we will need to avoid mapping this DS3 data-bit about one in every
(22.35ms*8000) = 178.8 STS-1 SPEs.
What does this mean at the "Source" PTE?
All of this means that as the "Source" PTE maps this DS3 signal, with a data rate of 44.736Mbps - 1ppm into an
STS-1 signal, most of the resulting "outbound" STS-1 SPEs will transport 5592 DS3 data bits (e.g., 3 Stuff
Opportunity bits will be carrying DS3 data bits, the remaining 6 Stuff Opportunity bits are "stuff" bits). However,
in approximately one out of 178.8 "outbound" STS-1 SPEs, there will be a need for a "positive-stuffing" event.
98
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
Whenever these "positive-stuffing" events occur then (for these particular STS-1 SPEs) the SPE will carry only
5591 DS3 data bits (e.g., in this case, only 2 Stuff Opportunity bits will be carrying DS3 data-bits, and the
remaining 7 Stuff Opportunity bits are "stuff" bits).
Figure 47 presents an illustration of the STS-1 SPE traffic that will be generated by the "Source" PTE, during
this condition.
FIGURE 47. AN ILLUSTRATION OF THE STS-1 SPE TRAFFIC THAT WILL BE GENERATED BY THE SOURCE PTE, WHEN
MAPPING A DS3 SIGNAL THAT HAS A BIT RATE OF 44.736MBPS - 1PPM, INTO AN STS-1 SIGNAL
DS3 Data
Bit Excluded Here
SPE # N
Source
Source
PTE
PTE
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+1
SPE # N+177
5592
5592
DS3
DS3Data
Data
Bits
Bits
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+179
5591
5591
DS3
DS3Data
Data
Bits
Bits
5592
5592
DS3
DS3Data
Data
Bits
Bits
SPE # N+178
44.736Mbps - 1ppm
STS-1 SPE Data Stream
What does this mean at the Destination PTE?
In this case, this DS3 signal (which has now been mapped into an STS-1 data-stream) will be transported
across the SONET network. As this STS-1 signal arrives at the "Destination" PTE, this PTE will extract (or demap) this DS3 data from each incoming STS-1 SPE. Now, in this case, most (e.g., 177/178.8) of the incoming
STS-1 SPEs will contain 5592 DS3 data-bits. Therefore, the nominal data rate of the DS3 signal being demapped from SONET will be 44.736Mbps. However, in approximately 1 out of every 178 incoming STS-1
SPEs, the SPE will carry only 5591 DS3 data bits. This means that (during these times) the data rate of the demapped DS3 signal will have an instantaneous frequency that is less than 44.736Mbps. These "excursions" of
the de-mapped DS3 data-rate, from the nominal DS3 frequency can be viewed as occurrences of mapping/demapping jitter with an amplitude of approximately 1UI-pp.
Since this occurrence of "de-mapping" jitter is periodic and occurs once every 22.35ms, we can state that this
jitter has a frequency of 44.7Hz.
We talked about De-Mapping Jitter, What about De-Mapping Wander?
The Telcordia and Bellcore specifications define "Wander" as "Jitter with a frequency of less than 10Hz".
Based upon this definition, the DS3 signal (that is being transported by SONET) will cease to contain jitter and
will now contain "Wander", whenever the frequency offset of the DS3 signal being mapped into SONET is less
than 0.2ppm.
8.3
Jitter/Wander due to Pointer Adjustments
In the previous section, we described how a DS3 signal is asynchronously-mapped into SONET, and we also
defined "Mapping/De-mapping" jitter. In this section, we will describe how occurrences within the SONET
network will induce jitter/wander within the DS3 signal that is being transported across the SONET network.
In order to accomplish this, we will discuss the following topics in detail.
• The concept of an STS-1 SPE pointer
99
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
• The concept of Pointer Adjustments
• The causes of Pointer Adjustments
• How Pointer Adjustments induce jitter/wander within a DS3 signal being transported by that SONET network.
8.3.1
The Concept of an STS-1 SPE Pointer
As mentioned earlier, the STS-1 SPE is not aligned to the STS-1 frame boundaries and is permitted to "float"
within the Envelope Capacity. As a consequence, the STS-1 SPE will often times "straddle" across two
consecutive STS-1 frames. Figure 48 presents an illustration of an STS-1 SPE straddling across two
consecutive STS-1 frames.
FIGURE 48. AN ILLUSTRATION OF AN STS-1 SPE STRADDLING ACROSS TWO CONSECUTIVE STS-1 FRAMES
TOH
STS-1 FRAME N + 1
STS-1 FRAME N
H1, H2
Bytes
J1 Byte (1st byte of next SPE)
J1 Byte (1st byte of SPE)
SPE can straddle across two STS-1 frames
A PTE that is receiving and terminating an STS-1 data-stream will perform the following tasks.
• It will acquire and maintain STS-1 frame synchronization with the incoming STS-1 data-stream.
• Once the PTE has acquired STS-1 frame synchronization, then it will locate the J1 byte (e.g., the very byte
within the very next STS-1 SPE) within the Envelope Capacity by reading out the contents of the H1 and H2
bytes.
The H1 and H2 bytes are referred to (in the SONET standards) as the SPE Pointer Bytes. When these two
bytes are concatenated together in order to form a 16-bit word (with the H1 byte functioning as the "Most
Significant Byte") then the contents of the "lower" 10 bit-fields (within this 16-bit word) reflects the location of
the J1 byte within the Envelope Capacity of the incoming STS-1 data-stream. Figure 49 presents an
illustration of the bit format of the H1 and H2 bytes, and indicates which bit-fields are used to reflect the
location of the J1 byte.
100
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 49. THE BIT-FORMAT OF THE 16-BIT WORD (CONSISTING OF THE H1 AND H2 BYTES) WITH THE 10 BITS,
REFLECTING THE LOCATION OF THE J1 BYTE, DESIGNATED
H1 Byte
H2 Byte
MSB
LSB
N N N N S S X X X X X X X X X X
10 Bit Pointer Expression
Figure 50 relates the contents within these 10 bits (within the H1 and H2 bytes) to the location of the J1 byte
(e.g., the very first byte of the STS-1 SPE) within the Envelope Capacity.
FIGURE 50. THE RELATIONSHIP BETWEEN THE CONTENTS OF THE "POINTER BITS" (E.G., THE 10-BIT EXPRESSION
WITHIN THE H1 AND H2 BYTES) AND THE LOCATION OF THE J1 BYTE WITHIN THE ENVELOPE CAPACITY OF AN STS1 FRAME
TOH
A1
B1
D1
H1
B2
D4
D7
D10
S1
A2
E1
D2
H2
K1
D5
D8
D11
M0
The Pointer Value “0” is immediately
After the H3 byte
C1/J0
F1
D3
H3
K2
D6
D9
D12
E2
522
609
696
0
87
174
261
348
435
523
610
697
1
88
175
262
349
436
********
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
* * * ** ** * * *
**
607
694
781
85
172
259
346
433
520
608
695
782
86
173
260
347
434
521
NOTES:
1.
If the content of the "Pointer Bits" is "0x00" then the J1 byte is located immediately after the H3 byte, within the
Envelope Capacity.
2.
If the contents of the 10-bit expression exceed the value of 0x30F (or 782, in decimal format) then it does not
contain a valid pointer value.
8.3.2
Pointer Adjustments within the SONET Network
The word SONET stands for "Synchronous Optical NETwork. This name implies that the entire SONET
network is synchronized to a single clock source. However, because the SONET (and SDH) Networks can
101
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
span thousands of miles, traverse many different pieces of equipments, and even cross International
boundaries; in practice, the SONET/SDH network is NOT synchronized to a single clock source.
In practice, the SONET/SDH network can be thought of as being divided into numerous "Synchronization
Islands". Each of these "Synchronization Islands" will consist of numerous pieces of SONET Terminal
Equipment. Each of these pieces of SONET Terminal Equipment will all be synchronized to a single Stratum-1
clock source which is the most accurate clock source within the Synchronization Island. Typically a
"Synchronization Island" will consist of a single "Timing Master" equipment along with multiple "Timing Slave"
pieces of equipment. This "Timing Master" equipment will be directly connected to the Stratum-1 clock source
and will have the responsibility of distributing a very accurate clock signal (that has been derived from the
Stratum 1 clock source) to each of the "Timing Slave" pieces of equipment within the "Synchronization Island".
The purpose of this is to permit each of the "Timing Slave" pieces of equipment to be "synchronized" with the
"Timing Master" equipment, as well as the Stratum 1 Clock source. Typically this "clock distribution" is
performed in the form of a BITS (Building Integrated Timing Supply) clock, in which a very precise clock signal
is provided to the other pieces of equipment via a T1 or E1 line signal.
Many of these "Synchronization Islands" will use a Stratum-1" clock source that is derived from GPS pulses
that are received from Satellites that operate at Geo-synchronous orbit. Other "Synchronization Islands" will
use a Stratum-1" clock source that is derived from a very precise local atomic clock. As a consequence,
different "Synchronization Islands" will use different Stratum 1 clock sources. The up-shot of having these
"Synchronization Islands" that use different "Stratum-1 clock" sources, is that the Stratum 1 Clock frequencies,
between these "Synchronization Islands" are likely to be slightly different from each other. These "frequencydifferences" within Stratum 1 clock sources will result in "clock-domain changes" as a SONET signal (that is
traversing the SONET network) passes from one "Synchronization Island" to another.
The following section will describe how these "frequency differences" will cause a phenomenon called "pointer
adjustments" to occur in the SONET Network.
8.3.3
Causes of Pointer Adjustments
The best way to discuss how pointer adjustment events occur is to consider an STS-1 signal, which is driven
by a timing reference of frequency f1; and that this STS-1 signal is being routed to a network equipment (that
resides within a different "Synchronization Island") and processes STS-1 data at a frequency of f2.
NOTE: Clearly, both frequencies f1 and f2 are at the STS-1 rate (e.g., 51.84MHz). However, these two frequencies are
likely to be slightly different from each other.
Now, since the STS-1 signal (which is of frequency f1) is being routed to the network element (which is
operating at frequency f2), the typical design approach for handling "clock-domain" differences is to route this
STS-1 signal through a "Slip Buffer" as illustrated below.
102
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 51. AN ILLUSTRATION OF AN STS-1 SIGNAL BEING PROCESSED VIA A SLIP BUFFER
Clock Domain operating
At frequency f1
STS-1 Data_IN
STS-1 Clock_f1
STS-1 Data_OUT
SLIP
SLIPBUFFER
BUFFER
STS-1 Clock_f2
Clock Domain operating
At Frequency f2.
In the "Slip Buffer, the "input" STS-1 data (labeled "STS-1 Data_IN") is latched into the FIFO, upon a given
edge of the corresponding "STS-1 Clock_f1" input clock signal. The STS-1 Data (labeled "STS-1 Data_OUT")
is clocked out of the Slip Buffer upon a given edge of the "STS-1 Clock_f2" input clock signal.
The behavior of the data, passing through the "Slip Buffer" is now described for each possible relationship
between frequencies f1 and f2.
If f1 = f2
If both frequencies, f1 and f2 are exactly equal, then the STS-1 data will be "clocked" into the "Slip Buffer" at
exactly the same rate that it is "clocked out". In this case, the "Slip Buffer" will neither fill-up nor become
depleted. As a consequence, no pointer-adjustments will occur in this STS-1 data stream. In other words, the
STS-1 SPE will remain at a constant location (or offset) within each STS-1 envelope capacity for the duration
that this STS-1 signal is supporting this particular service.
If f1 < f2
If frequency f1 is less than f2, then this means that the STS-1 data is being "clocked out" of the "Slip Buffer" at
a faster rate than it is being clocked in. In this case, the "Slip Buffer" will eventually become depleted.
Whenever this occurs, a typical strategy is to "stuff" (or insert) a "dummy byte" into the data stream. The
purpose of stuffing this "dummy byte" is to compensate for the frequency differences between f1 and f2, and
attempt to keep the "Slip Buffer, at a somewhat constant fill level.
NOTE: This "dummy byte" does not carry any valuable information (not for the user, nor for the system).
Since this "dummy byte" carries no useful information, it is important that the "Receiving PTE" be notified
anytime this "dummy byte" stuffing occurs. This way, the Receiving Terminal can "know" not to treat this
"dummy byte" as user data.
Byte-Stuffing and Pointer Incrementing in a SONET Network
Whenever this "byte-stuffing" occurs then the following other things occur within the STS-1 data stream.
During the STS-1 frame that contains the "Byte-Stuffing" event
a. The "stuff-byte" will be inserted into the byte position immediately after the H3 byte. This insertion of the
"dummy byte" immediately after the H3 byte position will cause the J1 byte (and in-turn, the rest of the
SPE) to be "byte-shifted" away from the H3 byte. As a consequence, the offset between the H3 byte position and the STS-1 SPE will now have been increased by 1 byte.
103
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
b. The "Transmitting" Network Equipment will notify the remote terminal of this byte-stuffing event, by inverting certain bits within the "pointer word" (within the H1 and H2 bytes) that are referred to as "I" bits.
Figure 52 presents an illustration of the bit-format within the 16-bit word (consist of the H1 and H2 bytes) with
the "I" bits designated.
FIGURE 52. AN ILLUSTRATION OF THE BIT FORMAT WITHIN THE 16-BIT WORD (CONSISTING OF THE H1 AND H2
BYTES) WITH THE "I" BITS DESIGNATED
H1 Byte
H2 Byte
MSB
LSB
N N N N S S I D I D I D I D I D
10 Bit Pointer Expression
NOTE: At this time the "I" bits are inverted in order to denote that an "incrementing" pointer adjustment event is currently
occurring.
During the STS-1 frame that follows the "Byte-Stuffing" event
The "I" bits (within the "pointer-word") will be set back to their normal value; and the contents of the H1 and H2
bytes will be incremented by "1".
If f1 > f2
If frequency f1 is greater than f2, then this means that the STS-1 data is being clocked into the "Slip Buffer" at
a faster rate than is being clocked out. In this case, the "Slip Buffer" will start to fill up. Whenever this occurs,
a typical strategy is to delete (e.g., negative-stuff) a byte from the Slip Buffer. The purpose of this "negativestuffing" is to compensate for the frequency differences between f1 and f2; and to attempt to keep the "Slip
Buffer" at a somewhat constant fill-level.
NOTE: This byte, which is being "un-stuffed" does carry valuable information for the user (e.g., this byte is typically a
payload byte). Therefore, whenever this negative stuffing occurs, two things must happen.
a. The "negative-stuffed" byte must not be simply discarded. In other words, it must somehow also be
transmitted to the remote PTE with the remainder of the SPE data.
b. The remote PTE must be notified of the occurrence of these "negative-stuffing" events. Further, the
remote PTE must know where to obtain this "negative-stuffed" byte.
Negative-Stuffing and Pointer-Decrementing in a SONET Network
Whenever this "byte negative-stuffing" occurs then the following other things occur within the STS-1 datastream.
During the STS-1 frame that contains the "Negative Byte-Stuffing" Event
a. The "Negative-Stuffed" byte will be inserted into the H3 byte position. Whenever an SPE data byte is
inserted into the H3 byte position (which is ordinarily an unused byte), the number of bytes that will exist
between the H3 byte and the J1 byte within the very next SPE will be reduced by 1 byte. As a
consequence, in this case, the J1 byte (and in-turn, the rest of the SPE) will now be "byte-shifted"
towards the H3 byte position.
104
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
b. The "Transmitting" Network Element will notify the remote terminal of this "negative-stuff" event by
inverting certain bits within the "pointer word" (within the H1 and H2 bytes) that are referred to as "D" bits.
Figure 53 presents an illustration of the bit format within the 16-bit word (consisting of the H1 and H2 bytes)
with the "D" bits designated.
FIGURE 53. AN ILLUSTRATION OF THE BIT-FORMAT WITHIN THE 16-BIT WORD (CONSISTING OF THE H1 AND H2
BYTES) WITH THE "D" BITS DESIGNATED
H1 Byte
H2 Byte
MSB
LSB
N N N N S S I D I D I D I D I D
10 Bit Pointer Expression
NOTE: At this time the "D" bits are inverted in order to denote that a "decrementing" pointer adjustment event is currently
occurring.
During the STS-1 frame that follows the "Negative Byte-Stuffing" Event
The "D" bits (within the pointer-word) will be set back to their normal value; and the contents of the H1 and H2
bytes will be decremented by one.
105
XRT75R12D
REV. 1.0.1
8.3.4
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Why are we talking about Pointer Adjustments?
The overall SONET network consists of numerous "Synchronization Islands". As a consequence, whenever a
SONET signal is being transmitted from one "Synchronization Island" to another; that SONET signal will
undergo a "clock domain" change as it traverses the network. This clock domain change will result in periodic
pointer-adjustments occurring within this SONET signal. Depending upon the direction of this "clock-domain"
shift that the SONET signal experiences, there will either be periodic "incrementing" pointer-adjustment events
or periodic "decrementing" pointer-adjustment events within this SONET signal.
Regardless of whether a given SONET signal is experiencing incrementing or decrementing pointer
adjustment events, each pointer adjustment event will result in an abrupt 8-bit shift in the position of the SPE
within the STS-1 data-stream. If this STS-1 signal is transporting an "asynchronously-mapped" DS3 signal;
then this 8-bit shift in the location of the SPE (within the STS-1 signal) will result in approximately 8UIpp of jitter
within the asynchronously-mapped DS3 signal, as it is de-mapped from SONET. In “Section 8.5, A Review of
the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3 applications” on
page 107 we will discuss the "Category I Intrinsic Jitter Requirements (for DS3 Applications) per Telcordia GR253-CORE. However, for now we will simply state that this 8UIpp of intrinsic jitter far exceeds these "intrinsic
jitter" requirements.
In summary, pointer-adjustments events are a "fact of life" within the SONET/SDH network. Further, pointeradjustment events, within a SONET signal that is transporting an asynchronously-mapped DS3 signal, will
impose a significant impact on the Intrinsic Jitter and Wander within that DS3 signal as it is de-mapped from
SONET.
8.4
Clock Gapping Jitter
In most applications (in which the LIU will be used in a SONET De-Sync Application) the user will typically
interface the LIU to a Mapper Device in the manner as presented below in Figure 54.
FIGURE 54. ILLUSTRATION OF THE TYPICAL APPLICATIONS FOR THE LIU IN A SONET DE-SYNC APPLICATION
De-Mapped (Gapped)
DS3 Data and Clock
TPDATA_n input pin
STS-N Signal
DS3to
toSTS-N
STS-N
DS3
Mapper/
Mapper/
Demapper
Demapper
IC
IC
LIU
LIU
TCLK_n input
In this application, the Mapper IC will have the responsibility of receiving an STS-N signal (from the SONET
Network) and performing all of the following operations on this STS-N signal.
• Byte-de-interleaving this incoming STS-N signal into N STS-1 signals
• Terminating each of these STS-1 signals
• Extracting (or de-mapping) the DS3 signal(s) from the SPEs within each of these terminated STS-1 signals.
106
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
In this application, these Mapper devices can be thought of as multi-channel devices. For example, an STS-3
Mapper can be viewed as a 3-Channel DS3/STS-1 to STS-3 Mapper IC. Similarly, an STS-12 Mapper can be
viewed as a 12-Channel DS3/STS-1 to STS-12 Mapper IC. Continuing on with this line of thought, if a Mapper
IC is configured to receive an STS-N signal, and (from this STS-N signal) de-map and output N DS3 signals
(towards the DS3 facility), then it will typically do so in the following manner.
• In many cases, the Mapper IC will output this DS3 signal, using both a "Data-Signal" and a "Clock-Signal".
In many cases, the Mapper IC will output the contents of an entire STS-1 data-stream via the Data-Signal.
• However, as the Mapper IC output this STS-1 data-stream, it will typically supply clock pulses (via the ClockSignal output) coincident to whenever a DS3 bit is being output via the Data-Signal. In this case, the Mapper
IC will NOT supply a clock pulse coincident to when a TOH, POH, or any "non-DS3 data-bit" is being output
via the "Data-Signal".
Now, since the Mapper IC will output the entire STS-1 data stream (via the Data-Signal), the output ClockSignal will be of the form such that it has a period of 19.3ns (e.g., a 51.84MHz clock signal). However, the
Mapper IC will still generate approximately 44,736,000 clock pulses during any given one second period.
Hence, the clock signal that is output from the Mapper IC will be a horribly gapped 44.736MHz clock signal.
One can view such a clock signal as being a very-jittery 44.736MHz clock signal. This jitter that exists within
the "Clock-Signal" is referred to as "Clock-Gapping" Jitter. A more detailed discussion on how the user must
handle this type of jitter is presented in “Section 8.8.2, Recommendations on Pre-Processing the Gapped
Clocks (from the Mapper/ASIC Device) prior to routing this DS3 Clock and Data-Signals to the Transmit
Inputs of the LIU” on page 119.
8.5
A Review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3
applications
The "Category I Intrinsic Jitter Requirements" per Telcordia GR-253-CORE (for DS3 applications) mandates
that the user perform a large series of tests against certain specified "Scenarios". These "Scenarios" and their
corresponding requirements is summarized in Table 41, below.
TABLE 41: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
DS3 De-Mapping
Jitter
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
COMMENTS
0.4UI-pp
Includes effects of De-Mapping and Clock Gapping Jitter
Single Pointer
Adjustment
A1
0.3UI-pp + Ao
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.NOTE: Ao is the amount
of intrinsic jitter that was measured during the "DS3 DeMapping Jitter" phase of the Test.
Pointer Bursts
A2
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
Phase Transients
A3
1.2UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
87-3 Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
87-3 Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
87-3 Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
107
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
TABLE 41: SUMMARY OF "CATEGORY I INTRINSIC JITTER REQUIREMENT PER TELCORDIA GR-253-CORE, FOR DS3
APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
TELCORDIA GR-253-CORE
CATEGORY I INTRINSIC
JITTER REQUIREMENTS
Continuous Pattern
A4
1.0UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
Continuous Add
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
Continuous Cancel
A5
1.3UI-pp
Includes effects of Jitter from Clock-Gapping, De-Mapping and Pointer Adjustments.
COMMENTS
NOTE: All of these intrinsic jitter measurements are to be performed using a band-pass filter of 10Hz to 400kHz.
Each of the scenarios presented in Table 41, are briefly described below.
8.5.1
DS3 De-Mapping Jitter
DS3 De-Mapping Jitter is the amount of Intrinsic Jitter that will be measured within the "Line" or "Facility-side"
DS3 signal, (after it has been de-mapped from a SONET signal) without the occurrence of "Pointer
Adjustments" within the SONET signal.
Telcordia GR-253-CORE requires that the "DS3 De-Mapping" Jitter be less than 0.4UI-pp, when measured
over all possible combinations of DS3 and STS-1 frequency offsets.
8.5.2
Single Pointer Adjustment
Telcordia GR-253-CORE states that if each pointer adjustment (within a continuous stream of pointer
adjustments) is separated from each other by a period of 30 seconds, or more; then they are sufficiently
isolated to be considered "Single-Pointer Adjustments".
Figure 55 presents an illustration of the "Single Pointer Adjustment" Scenario.
FIGURE 55. ILLUSTRATION OF SINGLE POINTER ADJUSTMENT SCENARIO
Pointer Adjustment Events
>30s
Initialization
Cool Down
Measurement Period
Telcordia GR-253-CORE states that the Intrinsic Jitter that is measured (within the DS3 signal) that is
ultimately de-mapped from a SONET signal that is experiencing "Single-Pointer Adjustment" events, must
NOT exceed the value 0.3UI-pp + Ao.
NOTES:
1.
Ao is the amount of Intrinsic Jitter that was measured during the "De-Mapping" Jitter portion of this test.
108
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
2.
8.5.3
Testing must be performed for both Incrementing and Decrementing Pointer Adjustments.
Pointer Burst
Figure 56 presents an illustration of the "Pointer Burst" Pointer Adjustment Scenario per Telcordia GR-253CORE.
FIGURE 56. ILLUSTRATION OF BURST OF POINTER ADJUSTMENT SCENARIO
Pointer Adjustment Events
Pointer Adjustment Burst Train
t
0.5ms
0.5ms
>30s
Initialization
Cool Down
Measurement Period
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "Burst of Pointer Adjustment" scenario, must NOT exceed 1.3UI-pp.
8.5.4
Phase Transients
Figure 57 presents an illustration of the "Phase Transients" Pointer Adjustment Scenario per Telcordia GR253-CORE.
109
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 57. ILLUSTRATION OF "PHASE-TRANSIENT" POINTER ADJUSTMENT SCENARIO
Pointer Adjustment Events
Pointer Adjustment Burst Train
0.5s
0.25s
0.25s
t
>30s
Initialization
Cool Down
Measurement Period
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "Phase Transient - Pointer Adjustment" scenario must NOT exceed
1.2UI-pp.
8.5.5
87-3 Pattern
Figure 58 presents an illustration of the "87-3 Continuous Pattern" Pointer Adjustment Scenario per Telcordia
GR-253-CORE.
FIGURE 58. AN ILLUSTRATION OF THE 87-3 CONTINUOUS POINTER ADJUSTMENT PATTERN
Repeating 87-3 Pattern (see below)
Pointer Adjustment Events
Initialization
Measurement Period
87-3 Pattern
87 Pointer Adjustment Events
No Pointer
Adjustments
NOTE: T ranges from 34ms to 10s (Req)
T ranges from 7.5ms to 34ms (Obj)
T
110
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
Telcordia GR-253-CORE defines an "87-3 Continuous" Pointer Adjustment pattern, as a repeating sequence of
90 pointer adjustment events. Within this 90 pointer adjustment event, 87 pointer adjustments are actually
executed. The remaining 3 pointer adjustments are never executed. The spacing between individual pointer
adjustment events (within this scenario) can range from 7.5ms to 10seconds.
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "87-3 Continuous" pattern of Pointer Adjustments, must not exceed
1.0UI-pp.
8.5.6
87-3 Add
Figure 59 presents an illustration of the "87-3 Add Pattern" Pointer Adjustment Scenario per Telcordia GR-253CORE.
FIGURE 59. ILLUSTRATION OF THE 87-3 ADD POINTER ADJUSTMENT PATTERN
Added Pointer Adjustment
No Pointer
Adjustments
43 Pointer Adjustments
T
43 Pointer Adjustments
t
Telcordia GR-253-CORE defines an "87-3 Add" Pointer Adjustment, as the "87-3 Continuous" Pointer
Adjustment pattern, with an additional pointer adjustment inserted, as shown above in Figure 59.
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "87-3 Add" pattern of Pointer Adjustments, must not exceed 1.3UIpp.
8.5.7
87-3 Cancel
Figure 60 presents an illustration of the 87-3 Cancel Pattern Pointer Adjustment Scenario per Telcordia GR253-CORE.
111
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 60. ILLUSTRATION OF 87-3 CANCEL POINTER ADJUSTMENT SCENARIO
No Pointer
Adjustments
86 or 87 Pointer Adjustments
T
Cancelled
Pointer Adjustment
Telcordia GR-253-CORE defines an "87-3 Cancel" Pointer Adjustment, as the "87-3 Continuous" Pointer
Adjustment pattern, with an additional pointer adjustment cancelled (or not executed), as shown above in
Figure 60.
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "87-3 Cancel" pattern of Pointer Adjustments, must not exceed 1.3UIpp.
8.5.8
Continuous Pattern
Figure 61 presents an illustration of the "Continuous" Pointer Adjustment Scenario per Telcordia GR-253CORE.
FIGURE 61. ILLUSTRATION OF CONTINUOUS PERIODIC POINTER ADJUSTMENT SCENARIO
Repeating Continuous Pattern (see below)
Pointer Adjustment Events
Initialization
Measurement Period
T
112
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "Continuous" pattern of Pointer Adjustments, must not exceed 1.0UIpp. The spacing between individual pointer adjustments (within this scenario) can range from 7.5ms to 10s.
8.5.9
Continuous Add
Figure 62 presents an illustration of the "Continuous Add Pattern" Pointer Adjustment Scenario per Telcordia
GR-253-CORE.
FIGURE 62. ILLUSTRATION OF CONTINUOUS-ADD POINTER ADJUSTMENT SCENARIO
Added Pointer Adjustment
Continuous Pointer Adjustments
T
Continuous Pointer Adjustments
t
Telcordia GR-253-CORE defines an "Continuous Add" Pointer Adjustment, as the "Continuous" Pointer
Adjustment pattern, with an additional pointer adjustment inserted, as shown above in Figure 62.
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "Continuous Add" pattern of Pointer Adjustments, must not exceed
1.3UI-pp.
8.5.10
Continuous Cancel
Figure 63 presents an illustration of the "Continuous Cancel Pattern" Pointer Adjustment Scenario per
Telcordia GR-253-CORE.
113
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 63. ILLUSTRATION OF CONTINUOUS-CANCEL POINTER ADJUSTMENT SCENARIO
Continuous Pointer Adjustments
T
Cancelled
Pointer Adjustment
Telcordia GR-253-CORE defines a "Continuous Cancel" Pointer Adjustment, as the "Continuous" Pointer
Adjustment pattern, with an additional pointer adjustment cancelled (or not executed), as shown above in
Figure 63.
Telcordia GR-253-CORE mandates that the Intrinsic Jitter, within the DS3 signal that is de-mapped from a
SONET signal, which is experiencing the "Continuous Cancel" pattern of Pointer Adjustments, must not
exceed 1.3UI-pp.
8.6
A Review of the DS3 Wander Requirements per ANSI T1.105.03b-1997.
To be provided in the next revision of this data sheet.
8.7
A Review of the Intrinsic Jitter and Wander Capabilities of the LIU in a typical system
application
The Intrinsic Jitter and Wander Test results are summarized in this section.
8.7.1
Intrinsic Jitter Test results
The Intrinsic Jitter Test results for the LIU in DS3 being de-mapped from SONET is summarized below in Table
2.
114
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 42: SUMMARY OF "CATEGORY I INTRINSIC JITTER TEST RESULTS" FOR SONET/DS3 APPLICATIONS
SCENARIO
DESCRIPTION
SCENARIO
NUMBER
DS3 De-Mapping
Jitter
LIU
INTRINSIC JITTER TEST RESULTS
TELCORDIA GR-253-CORE CATEGORY I
INTRINSIC JITTER REQUIREMENTS
0.13UI-pp
0.4UI-pp
Single Pointer
Adjustment
A1
0.201UI-pp
0.43UI-pp (e.g. 0.13UI-pp + 0.3UI-pp)
Pointer Bursts
A2
0.582UI-pp
1.3UI-pp
Phase Transients
A3
0.526UI-pp
1.2UI-pp
87-3 Pattern
A4
0.790UI-pp
1.0UI-pp
87-3 Add
A5
0.926UI-pp
1.3UI-pp
87-3 Cancel
A5
0.885UI-pp
1.3UI-pp
Continuous
Pattern
A4
0.497UI-pp
1.0UI-pp
Continuous Add
A5
0.598UI-pp
1.3UI-pp
Continuous
Cancel
A5
0.589UI-pp
1.3UI-pp
NOTES:
1.
A detailed test report on our Test Procedures and Test Results is available and can be obtained by contacting your
Exar Sales Representative.
2.
These test results were obtained via the LIUs mounted on our XRT94L43 12-Channel DS3/E3/STS-1 Mapper
Evaluation Board.
3.
These same results apply to SDH/AU-3 Mapping applications.
115
XRT75R12D
REV. 1.0.1
8.7.2
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Wander Measurement Test Results
Wander Measurement test results will be provided in the next revision of the LIU Data Sheet.
8.8
Designing with the LIU
In this section, we will discuss the following topics.
• How to design with and configure the LIU to permit a system to meet the above-mentioned Intrinsic Jitter and
Wander requirements.
• How is the LIU able to meet the above-mentioned requirements?
• How does the LIU permits the user to comply with the SONET APS Recovery Time requirements of 50ms
(per Telcordia GR-253-CORE)?
• How should one configure the LIU, if one needs to support "Daisy-Chain" Testing at the end Customer's site?
8.8.1
How to design and configure the LIU to permit a system to meet the above-mentioned
Intrinsic Jitter and Wander requirements
As mentioned earlier, in most application (in which the LIU will be used in a SONET De-Sync Application) the
user will typically interface the LIU to a Mapper device in the manner as presented below in Figure 64.
In this application, the Mapper has the responsibility of receiving a SONET STS-N/OC-N signal and extracting
as many as N DS3 signals from this signal. As a given channel within the Mapper IC extracts out a given DS3
signal (from SONET) it will typically be applying a Clock and Data signal to the "Transmit Input" of the LIU IC.
Figure 64 presents a simple illustration as to how one channel, within the LIU should be connected to the
Mapper IC.
FIGURE 64. ILLUSTRATION OF THE LIU BEING CONNECTED TO A MAPPER IC FOR SONET DE-SYNC APPLICATIONS
De-Mapped (Gapped)
DS3 Data and Clock
TPDATA_n input pin
STS-N Signal
DS3to
toSTS-N
STS-N
DS3
Mapper/
Mapper/
Demapper
Demapper
IC
IC
LIU
LIU
TCLK n input
As mentioned above, the Mapper IC will typically output a Clock and Data signal to the LIU. In many cases,
the Mapper IC will output the contents of an entire STS-1 data-stream via the Data Signal to the LIU. However,
the Mapper IC typically only supplies a clock pulse via the Clock Signal to the LIU coincident to whenever a
DS3 bit is being output via the Data Signal. In this case, the Mapper IC would not supply a clock edge
coincident to when a TOH, POH or any non-DS3 data-bit is being output via the Data-Signal.
Figure 64 indicates that the Data Signal from the Mapper device should be connected to the TPDATA_n input
pin of the LIU IC and that the Clock Signal from the Mapper device should be connected to the TCLK_n input
pin of the LIU IC.
In this application, the LIU has the following responsibilities.
116
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
• Using a particular clock edge within the "gapped" clock signal (from the Mapper IC) to sample and latch the
value of each DS3 data-bit that is output from the Mapper IC.
• To (through the user of the Jitter Attenuator block) attenuate the jitter within this "DS3 data" and "clock signal"
that is output from the Mapper IC.
• To convert this "smoothed" DS3 data and clock into industry-compliant DS3 pulses, and to output these
pulses onto the line.
To configure the LIU to operate in the correct mode for this application, the user must execute the following
configuration steps.
a. Configure the LIU to operate in the DS3 Mode
The user can configure a given channel (within the LIU) to operate in the DS3 Mode, by executing either of the
following steps.
• If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting both Bits 2 (E3_n) and Bits 1 (STS-1/DS3*_n), within each of the
"Channel Control Registers" to "0" as depicted below.
CHANNEL CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X06
CHANNEL 1 ADDRESS LOCATION = 0X0E
CHANNEL 2 ADDRESS LOCATION = 0X16
BIT 7
BIT 6
Unused
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
PRBS Enable
Ch_n
RLB_n
LLB_n
E3_n
STS-1/DS3_n
SR/DR_n
R/O
R/O
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
• If the LIU has been configured to operate in the Hardware Mode
The user can accomplish this by pulling all of the following input pins "Low".
Pin 76 - E3_0
Pin 94 - E3_1
Pin 85 - E3_2
Pin 72 - STS-1/DS3_0
Pin 98 - STS-1/DS3_1
Pin 81 - STS-1/DS3_2
b. Configure the LIU to operate in the Single-Rail Mode
Since the Mapper IC will typically output a single "Data Line" and a "Clock Line" for each DS3 signal that it
demaps from the incoming STS-N signal, it is imperative to configure each channel within the LIU to operate in
the Single Rail Mode.
The user can accomplish this by executing either of the following steps.
• If the LIU has been configured to operate in the Host Mode
The user can accomplish this by setting Bit 0 (SR/DR*), within the each of the "Channel Control" Registers to
1, as illustrated below.
117
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
CHANNEL CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X06
CHANNEL 1 ADDRESS LOCATION = 0X0E
CHANNEL 2 ADDRESS LOCATION = 0X16
BIT 7
BIT 6
Unused
BIT 5
BIT 4
BIT 3
BIT 2
PRBS Enable
Ch_n
RLB_n
LLB_n
E3_n
BIT 1
BIT 0
STS-1/
SR/DR_n
DS3_n
R/O
R/O
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
1
• If the LIU has been configured to operate in the Hardware Mode
Then the user should tie pin 65 (SR/DR*) to "High".
c. Configure each of the channels within the LIU to operate in the SONET De-Sync Mode
The user can accomplish this by executing either of the following steps.
• If the LIU has been configured to operate in the Host Mode.
Then the user should set Bit D2 (JA0) to "0" and Bit D0 (JA1) to "1", within the Jitter Attenuator Control
Register, as depicted below.
JITTER ATTENUATOR CONTROL REGISTER - (CHANNEL 0 ADDRESS LOCATION = 0X07
CHANNEL 1 ADDRESS LOCATION = 0X0F
CHANNEL 2 ADDRESS LOCATION = 0X17
BIT 7
BIT 6
BIT 5
Unused
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SONET APS
Recovery
Time
DisableCh_n
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
1
• If the LIU has been configured to operate in the Hardware Mode
Then the user should tie pin 44 (JA0) to a logic "HIGH" and pin 42 (JA1) to a logic "LOW".
Once the user accomplishes either of these steps, then the Jitter Attenuator (within the LIU) will be configured
to operate with a very narrow bandwidth.
d. Configure the Jitter Attenuator (within each of the channels) to operate in the Transmit Direction.
The user can accomplish this by executing either the following steps.
• If the LIU has been configured to operate in the Host Mode.
Then the user should be Bit D1 (JATx/JARx*) to "1", within the Jitter Attenuator Control Register, as depicted
below.
118
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07
CHANNEL 1 ADDRESS LOCATION = 0X0F
CHANNEL 2 ADDRESS LOCATION = 0X17
BIT 7
BIT 6
BIT 5
Unused
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SONET APS
Recovery
Time
DisableCh_n
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
1
1
• If the LIU has been configured to operate in the Hardware Mode.
Then the user should tie pin 43 (JATx/JARx*) to "1".
e. Enable the "SONET APS Recovery Time" Mode
Finally, if the user intends to use the LIU in an Application that is required to reacquire proper SONET and DS3
traffic, prior within 50ms of an APS (Automatic Protection Switching) event (per Telcordia GR-253-CORE), then
the user should set Bit 4 (SONET APS Recovery Time Disable), within the "Jitter Attenuator Control" Register,
to "0" as depicted below.
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07
CHANNEL 1 ADDRESS LOCATION = 0X0F
CHANNEL 2 ADDRESS LOCATION = 0X17
BIT 7
BIT 6
BIT 5
Unused
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SONET APS
Recovery
Time
DisableCh_n
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
1
NOTES:
1.
The ability to disable the "SONET APS Recovery Time" mode is only available if the LIU is operating in the Host
Mode. If the LIU is operating in the "Hardware" Mode, then this "SONET APS Recovery Time Mode" feature will
always be enabled.
2.
The "SONET APS Recovery Time" mode will be discussed in greater detail in “Section 8.8.3, How does the
LIU permit the user to comply with the SONET APS Recovery Time requirements of 50ms (per
Telcordia GR-253-CORE)?” on page 123.
8.8.2
Recommendations on Pre-Processing the Gapped Clocks (from the Mapper/ASIC Device)
prior to routing this DS3 Clock and Data-Signals to the Transmit Inputs of the LIU
In order to minimize the effects of "Clock-Gapping" Jitter within the DS3 signal that is ultimately transmitted to
the DS3 Line (or facility), we recommend that some "pre-processing" of the "Data-Signals" and "Clock-Signals"
(which are output from the Mapper device) be implemented prior to routing these signals to the "Transmit
Inputs" of the LIU.
8.8.2.1
SOME NOTES PRIOR TO STARTING THIS DISCUSSION:
119
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
Our simulation results indicate that Jitter Attenuator PLL (within the LIU LIU IC) will have no problem handling
and processing the "Data-Signal" and "Clock-Signal" from a Mapper IC/ASIC if no pre-processing has been
performed on these signals. In order words, our simulation results indicate that the Jitter Attenuator PLL
(within the LIU IC) will have no problem handling the "worst-case" of 59 consecutive bits of no clock pulses in
the "Clock-Signal (due to the Mapper IC processing the TOH bytes, an Incrementing Pointer-Adjustmentinduced "stuffed-byte", the POH byte, and the two fixed-stuff bytes within the STS-1 SPE, etc), immediately
followed be processing clusters of DS3 data-bits (as shown in Figure 44) and still comply with the "Category I
Intrinsic Jitter Requirements per Telcordia GR-253-CORE for DS3 applications.
NOTE: If this sort of "pre-processing" is already supported by the Mapper device that you are using, then no further action
is required by the user.
8.8.2.2
OUR PRE-PROCESSING RECOMMENDATIONS
For the time-being, we recommend that the customer implement the "pre-processing" of the DS3 "Data-Signal"
and "Clock-Signal" as described below. Currently we are aware that some of the Mapper products on the
Market do implement this exact "pre-processing" algorithm. However, if the customer is implementing their
Mapper Design in an ASIC or FPGA solution, then we strongly recommend that the user implement the
necessary logic design to realize the following recommendations.
Some time ago, we spent some time, studying (and then later testing our solution with) the PM5342 OC-3 to
DS3 Mapper IC from PMC-Sierra. In particular, we wanted to understand the type of "DS3 Clock" and "Data"
signal that this DS3 to OC-3 Mapper IC outputs.
During this effort, we learned the following.
1.
This "DS3 Clock" and "Data" signal, which is output from the Mapper IC consists of two major "repeating"
patterns (which we will refer to as "MAJOR PATTERN A" and "MAJOR PATTERN B". The behavior of
each of these patterns is presented below.
MAJOR PATTERN A
MAJOR PATTERN A consists of two "sub" or minor-patterns, (which we will refer to as "MINOR PATTERN P1
and P2).
MINOR PATTERN P1 consists of a string of seven (7) clock pulses, followed by a single gap (no clock pulse).
An illustration of MINOR PATTERN P1 is presented below in Figure 65.
FIGURE 65. ILLUSTRATION OF MINOR PATTERN P1
Missing Clock Pulse
1
2
3
4
5
6
7
It should be noted that each of these clock pulses has a period of approximately 19.3ns (or has an
"instantaneously frequency of 51.84MHz).
MINOR Pattern P2 consists of string of five (5) clock pulses, which is also followed by a single gap (no clock
pulse). An illustration of Pattern P2 is presented below in Figure 66.
120
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 66. ILLUSTRATION OF MINOR PATTERN P2
Missing Clock Pulse
1
2
3
4
5
HOW MAJOR PATTERN A IS SYNTHESIZED
MAJOR PATTERN A is created (by the Mapper IC) by:
• Repeating MINOR PATTERN P1 (e.g., 7 clock pulses, followed by a gap) 63 times.
• Upon completion of the 63rd transmission of MINOR PATTERN P1, MINOR PATTERN P2 is transmitted
repeatedly 36 times.
Figure 67 presents an illustration which depicts the procedure that is used to synthesize MAJOR PATTERN A
FIGURE 67. ILLUSTRATION OF PROCEDURE WHICH IS USED TO SYNTHESIZE MAJOR PATTERN A
Repeats 63 Times
MINOR PATTERN P1
Repeats 36 Times
MINOR PATTERN P2
Hence, MAJOR PATTERN A consists of "(63 x 7) + (36 x 5)" = 621 clock pulses. These 621 clock pulses were
delivered over a period of "(63 x 8) + (36 x 6)" = 720 STS-1 (or 51.84MHz) clock periods.
MAJOR PATTERN B
MAJOR PATTERN B consists of three sub or minor-patterns (which we will refer to as "MINOR PATTERNS P1,
P2 and P3).
MINOR PATTERN P1, which is used to partially synthesize MAJOR PATTERN B, is exactly the same "MINOR
PATTERN P1" as was presented above in Figure 37. Similarly, the MINOR PATTERN P2, which is also used
to partially synthesize MAJOR PATTERN B, is exactly the same "MINOR PATTERN P2" as was presented in
Figure 38.
MINOR PATTERN P3 (which has yet to be defined) consists of a string of six (6) clock pulses, which contains
no gaps. An illustration of MINOR PATTERN P3 is presented below in Figure 68.
121
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
FIGURE 68. ILLUSTRATION OF MINOR PATTERN P3
1
2
3
4
5
6
HOW MAJOR PATTERN B IS SYNTHESIZED
MAJOR PATTERN B is created (by the Mapper IC) by:
• Repeating MINOR PATTERN P1 (e.g., 7 clock pulses, followed by a gap) 63 times.
• Upon completion of the 63rd transmission of MINOR PATTERN P1, MINOR PATTERN P2 is transmitted
repeatedly 36 times.
• pon completion of the 35th transmission of MINOR PATTERN P2, MINOR PATTERN P3 is transmitted once.
Figure 69 presents an illustration which depicts the procedure that is used to synthesize MAJOR PATTERN B.
FIGURE 69. ILLUSTRATION OF PROCEDURE WHICH IS USED TO SYNTHESIZE PATTERN B
Transmitted 1 Time
Repeats 63 Times
PATTERN P1
Repeats 35 Times
PATTERN P2
PATTERN P3
Hence, MAJOR PATTERN B consists of "(63 x 7) + (35 x 5)" + 6 = 622 clock pulses.
These 622 clock pulses were delivered over a period of "(63 x 8) + (35 x 6) + 6 = 720 STS-1 (or 51.84MHz)
clock periods.
PUTTING THE PATTERNS TOGETHER
Finally, the DS3 to OC-N Mapper IC clock output is reproduced by doing the following.
• MAJOR PATTERN A is transmitted two times (repeatedly).
• After the second transmission of MAJOR PATTERN A, MAJOR PATTERN B is transmitted once.
• Then the whole process repeats.
Throughout the remainder of this document, we will refer to this particular pattern as the "SUPER PATTERN".
Figure 70 presents an illustration of this "SUPER PATTERN" which is output via the Mapper IC.
122
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
FIGURE 70. ILLUSTRATION OF THE SUPER PATTERN WHICH IS OUTPUT VIA THE "OC-N TO DS3" MAPPER IC
PATTERN A
PATTERN A
PATTERN B
CROSS-CHECKING OUR DATA
• Each SUPER PATTERN consists of (621 + 621 + 622) = 1864 clock pulses.
• The total amount of time, which is required for the "DS3 to OC-N Mapper" IC to transmit this SUPER
PATTERN is (720 + 720 + 720) = 2160 "STS-1" clock periods.
• This amount to a period of (2160/51.84MHz) = 41,667ns.
• In a period of 41, 667ns, the LIU (when configured to operate in the DS3 Mode), will output a total (41,667ns
x 44,736,000) = 1864 uniformly spaced DS3 clock pulses.
• Hence, the number of clock pulses match.
APPLYING THE SUPER PATTERN TO THE LIU
Whenever the LIU is configured to operate in a "SONET De-Sync" application, the device will accept a
continuous string of the above-defined SUPER PATTERN, via the TCLK input pin (along with the
corresponding data). The channel within the LIU (which will be configured to operate in the "DS3" Mode) will
output a DS3 line signal (to the DS3 facility) that complies with the "Category I Intrinsic Jitter Requirements per Telcordia GR-253-CORE (for DS3 applications). This scheme is illustrated below in Figure 71.
FIGURE 71. SIMPLE ILLUSTRATION OF THE LIU BEING USED IN A SONET DE-SYNCHRONIZER" APPLICATION
De-Mapped (Gapped)
DS3 Data and Clock
TPDATA_n input pin
STS-N Signal
DS3totoSTS-N
STS-N
DS3
Mapper/
Mapper/
Demapper
Demapper
IC
IC
LIU
LIU
TCLK_n input
8.8.3
How does the LIU permit the user to comply with the SONET APS Recovery Time
requirements of 50ms (per Telcordia GR-253-CORE)?
Telcordia GR-253-CORE, Section 5.3.3.3 mandates that the "APS Completion" (or Recovery) time be 50ms or
less. Many of our customers interpret this particular requirement as follows.
123
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
"From the instant that an APS is initiated on a high-speed SONET signal, all lower-speed SONET traffic (which
is being transported via this "high-speed" SONET signal) must be fully restored within 50ms. Similarly, if the
"high-speed" SONET signal is transporting some PDH signals (such as DS1 or DS3, etc.), then those entities
that are responsible for acquiring and maintaining DS1 or DS3 frame synchronization (with these DS1 or DS3
data-streams that have been de-mapped from SONET) must have re-acquired DS1 or DS3 frame
synchronization within 50ms" after APS has been initiated."
The LIU was designed such that the DS3 signals that it receives from a SONET Mapper device and processes
will comply with the Category I Intrinsic Jitter requirements per Telcordia GR-253-CORE.
Reference 1 documents some APS Recovery Time testing, which was performed to verify that the Jitter
Attenuator blocks (within the LIU) device that permit it to comply with the Category I Intrinsic Jitter
Requirements (for DS3 Applications) per Telcordia GR-253-CORE, do not cause it to fail to comply with the
"APS Completion Time" requirements per Section 5.3.3.3 of Telcordia GR-253-CORE. However, Table 3
presents a summary of some APS Recovery Time requirements that were documented within this test report.
Table 3,
TABLE 43: MEASURED APS RECOVERY TIME AS A FUNCTION OF DS3 PPM OFFSET
DS3 PPM OFFSET (PER W&G ANT-20SE)
MEASURED APS RECOVERY TIME (PER LOGIC ANALYZER)
-99 ppm
1.25ms
-40ppm
1.54ms
-30 ppm
1.34ms
-20 ppm
1.49ms
-10 ppm
1.30ms
0 ppm
1.89ms
+10 ppm
1.21ms
+20 ppm
1.64ms
+30 ppm
1.32ms
+40 ppm
1.25ms
+99 ppm
1.35ms
NOTE: The APS Completion (or Recovery) time requirement is 50ms.
Configuring the LIU to be able to comply with the SONET APS Recovery Time Requirements of 50ms
Quite simply, the user can configure a given Jitter Attenuator block (associated with a given channel) to (1)
comply with the "APS Completion Time" requirements per Telcordia GR-253-CORE, and (2) also comply with
the "Category I Intrinsic Jitter Requirements per Telcordia GR-253-CORE (for DS3 applications) by making
sure that Bit 4 (SONET APS Recovery Time Disable Ch_n), within the Jitter Attenuator Control Register is set
to "0" as depicted below.
124
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07
CHANNEL 1 ADDRESS LOCATION = 0X0F
CHANNEL 2 ADDRESS LOCATION = 0X17
BIT 7
BIT 6
BIT 5
Unused
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SONET APS
Recovery
Time Disable
Ch_n
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
1
1
NOTE: The user can only disable the "SONET APS Recovery Time Mode" if the LIU is operating in the Host Mode. If the
user is operating the LIU in the Hardware Mode, then the user will have NO ability to disable the "SONET APS
Recovery Time Mode" feature.
8.8.4
How should one configure the LIU, if one needs to support "Daisy-Chain" Testing at the end
Customer's site?
Daisy-Chain testing is emerging as a new requirements that many of our customers are imposing on our
SONET Mapper and LIU products. Many System Designer/Manufacturers are finding out that whenever their
end-customers that are evaluating and testing out their systems (in order to determine if they wish to move
forward and start purchasing this equipment in volume) are routinely demanding that they be able to test out
these systems with a single piece of test equipment. This means that the end-customer would like to take a
single piece of DS3 or STS-1 test equipment and (with this test equipment) snake the DS3 or STS-1 traffic
(that this test equipment will generate) through many or (preferably all) channels within the system. For
example, we have had request from our customers that (on a system that supports OC-192) our silicon be able
to support this DS3 or STS-1 traffic snaking through the 192 DS3 or STS-1 ports within this system.
After extensive testing, we have determined that the best approach to complying with test "Daisy-Chain"
Testing requirements, is to configure the Jitter Attenuator blocks (within each of the Channels within the LIU)
into the "32-Bit" Mode. The user can configure the Jitter Attenuator block (within a given channel of the LIU) to
operate in this mode by settings in the table below.
JITTER ATTENUATOR CONTROL REGISTER - CHANNEL 0 ADDRESS LOCATION = 0X07
CHANNEL 1 ADDRESS LOCATION = 0X0F
CHANNEL 2 ADDRESS LOCATION = 0X17
BIT 7
BIT 6
BIT 5
Unused
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SONET APS
Recovery
Time Disable
Ch_n
JA RESET
Ch_n
JA1 Ch_n
JA in Tx Path
Ch_n
JA0 Ch_n
R/O
R/O
R/O
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
1
1
0
REFERENCES
1. TEST REPORT - AUTOMATIC PROTECTION SWITCHING (APS) RECOVERY TIME TESTING WITH
THE XRT94L43 DS3/E3/STS-1 TO STS-12 MAPPER IC - Revision C Silicon
125
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
9.0 ELECTRICAL CHARACTERISTICS
TABLE 44: ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
MIN
MAX
UNITS
COMMENTS
VDD
Supply Voltage
-0.5
6.0
V
Note 1
VIN
Input Voltage at any Pin
-0.5
5.5
V
Note 1
IIN
Input current at any pin
100
mA
Note 1
STEMP
Storage Temperature
-65
150
0
C
Note 1
ATEMP
Ambient Operating Temperature
-40
85
0C
linear airflow 0 ft./min
Theta JA
Thermal Resistance
C/W
linear air flow 200ft/min
7.5
0
(See Note 3 below)
MLEVL
Exposure to Moisture
5
level
EIA/JEDEC
JESD22-A112-A
ESD
ESD Rating
2000
V
Note 2
NOTES:
1.
Exposure to or operating near the Min or Max values for extended period may cause permanent failure and impair
reliability of the device.
2.
ESD testing method is per MIL-STD-883D,M-3015.7
3.
Linear Air flow of 200 ft/min recommended for Industrial Applications. Theta JA = 9.4°C/W with 0 Lft/min, Theta JA
= 7.1 °C/W with 400Lft/min.
TABLE 45: DC ELECTRICAL CHARACTERISTICS:
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNITS
DVDD
Digital Supply Voltage
3.135
3.3
3.465
V
AVDD
Analog Supply Voltage
3.135
3.3
3.465
V
ICC_DS3
DS3 current consumption using PRBS 223-1 pattern 3
1016
1117
mA
ICC_DS3JA
DS3 current consumption using PRBS 223-1 pattern 4
1172
1290
mA
ICC_E3
E3 current consumption using PRBS 223-1 pattern 3
1040
1140
mA
ICC_E3JA
E3 current consumption using PRBS 223-1 pattern 4
1180
1300
mA
ICC_STS1
STS1 current consumption using PRBS 223-1 pattern 3
1100
1210
mA
ICC_STS1JA
STS1 current consumption using PRBS 223-1 pattern 4
1300
1430
mA
DS3 Power Consumption 5
3.35
3.87
W
DS3 Power Consumption with Jitter Attenuator Enabled 5
3.87
4.47
W
E3 Power Consumption 5
3.43
3.95
W
PCC_E3JA
E3 Power Consumption with Jitter Attenuator Enabled 5
3.89
4.50
W
PCC_STS1
STS1 Power Consumption 5
3.63
4.19
W
PCC_DS3
PCC_DS3JA
PCC_E3
126
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
TABLE 45: DC ELECTRICAL CHARACTERISTICS:
PARAMETER
SYMBOL
MIN.
PCC_STS1JA STS1 Power Consumption with Jitter Attenuator Enabled 5
VIL
Input Low Voltage2
VIH
Input High Voltage2
VOL
Output Low Voltage, IOUT = - 4mA
VOH
Output High Voltage, IOUT = 4 mA
2.0
TYP.
MAX.
UNITS
4.29
4.95
W
0.8
V
5.5
V
0.4
V
2.4
V
IL
Input Leakage Current1
±10
µA
CI
Input Capacitance
10
pF
CL
Load Capacitance
10
pF
NOTES:
1.
Not applicable for pins with pull-up or pull-down resistors.
2.
The Digital inputs are TTL 5V compliant.
3.
With Jitter Attenuator Disabled.
4.
With Jitter Attenuator Enabled.
5.
These values are not a measure of Power Dissipation. These values represent the Total Power Consumption.
i.e. PCC Consumption = PDD Dissipation + PLD Delivered to Load
127
XRT75R12D
REV. 1.0.1
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
ORDERING INFORMATION
PART NUMBER
PACKAGE
OPERATING TEMPERATURE RANGE
XRT75R12DIB
420 TBGA
-40°C to +85°C
PACKAGE DIMENSIONS -
E
420 Tape Ball Grid Array
(35 mm x 35 mm, TBGA)
Rev. 1.00
26
24
25
22
23
20
21
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
A1
FEATURE/MARK
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
D
N
D1
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
D1
D
(A1 corner feature is mfger option)
SYMBOL
A
A1
A2
D
D1
b
e
P
INCHES
MIN
MAX
0.051
0.067
0.020
0.028
0.031
0.039
1.370
1.386
1.5000 BSC
0.024
0.035
0.0500 BSC
0.006
0.012
128
MILLIMETERS
MIN
MAX
1.30
1.70
0.50
0.70
0.80
1.00
34.80
35.20
38.10 BSC
0.60
0.90
1.27 BSC
0.15
0.30
XRT75R12D
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER REV. 1.0.1
REVISIONS
REVISION
DATE
P1.0.0
09/22/03
Original
P1.0.1
10/30/03
Added Pull-Up resistor information for RDY and INT.
1.0.0
COMMENTS
April 2006 1.Added current and power consumption on Table 45, “DC Electrical Characteristics:,” on
page 126.
2. Revised Receive Monitor Enable Bit functional description and Section 3.3.1 description.
3. Updated Table 3, “The ALOS (Analog LOS) Declaration and Clearance Thresholds for a
given setting of REQEN (DS3 and STS-1 Applications),” on page 23.
4. Minor corrections on Transmitter Section of Features Summary on page 2.
5. Minor typo corrections in STS1Clk/12M pin description and in Section 1.0 and 4.4, Table 7
and Table 9.
6. Added Table 2, “Reference Clock Performance Specifications,” on page 19.
1.0.1
12/07/06
Corrected package thermal resistance specification.
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to
improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any
circuits described herein, conveys no license under any patent or other right, and makes no representation that
the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration
purposes and may vary depending upon a user’s specific application. While the information in this publication
has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the
failure or malfunction of the product can reasonably be expected to cause failure of the life support system or
to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless
EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has
been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately
protected under the circumstances.
Copyright 2006 EXAR Corporation
Datasheet December 2006.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
129