Model: FXO-HC52 SERIES HCMOS 5 x 3.2mm 2.5V Oscillator Freq: 0.75 MHz to 180MHz Rev. 03/24/2008 Features XTREMELY Low Jitter Low Cost XPRESS Delivery Frequency Resolution to six decimal places Stabilities to ± 20 PPM -20 to +70°C or -40 to +85°C operating temperatures Tri-State Enable / Disable Feature Industry Standard Package, Footprint & Pin-Out Fully RoHS compliant Gold over Nickel Termination Finish Serial ID with Comprehensive Traceability V DD Enable / Disable FOX X PRESSO OUTPUT ASICs Applications • • • • • • • • • ANY application requiring an oscillator SONET Ethernet Storage Area Network Broadband Access Microprocessors / DSP / FPGA Industrial Controllers Test and Measurement Equipment Fiber Channel GND For more information -- Click on the drawing Contents Description The Fox XPRESSO Crystal Oscillator is a breakthrough in configurable Frequency Control Solutions. XPRESSO utilizes a family of proprietary ASICs, designed and developed by Fox, with a key focus on noise reduction technologies. The 3rd order Delta Sigma Modulator reduces noise to the levels that are comparable to traditional Bulk Quartz and SAW oscillators. The ASICs family has ability to select the output type, input voltages, and temperature performance features. With the XPRESS lead-time, low cost, low noise, wide frequency range, excellent ambient performance, XpressO is an excellent choice over the conventional technologies. page Model Selection & Part Number Guide 2 Electrical Characteristic 3 Absolute Maximums 4 Output Wave Characteristics 4 Phase Noise 5 Jitter 5 Pin Assignment 6 Recommended Circuit 6 Reflow 6 Mechanical Drawing and Pad Layout 7 Tape and Reel Specification 8 Label 8 Traceability – LOT Number & Serial Identification 9 RoHS Material Declaration 10 SGS Report 11 & 12 Mechanical Test 13 Burn-In Test 13 MTTF / FITS calculations 14 15 Other XPRESSO Links Fox Contact Information 15 Finished XPRESSO parts are 100% final tested. FOXElectronics 5570 Enterprise Parkway Fort Myers, Florida 33905 USA +1.239.693.0099 FAX +1.239.693.1554 http://www.foxonline.com EMEA Tel/Fax: +44 .1767.312632 | Asia Hong Kong Tel: +852.2854.4285 Fax +852.2854.4282 Taiwan Tel: +886.2.22073427 Fax +886.2.22073486 | Japan Tel: +81.3.3374.2079 Fax: +81.3.3374.5221 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified Page 1 of 15 FXO-HC52 Series Model Selection Guide & Fox Part Number STEP #1: Customer selects the Model Description and provides to Fox Customer Service Model Description FXO – H C 5 2 6 R – 106.25 Frequency (in MHz) Resolutions to 6 places past the decimal point C = Ceramic H = HCMOS Q = Quartz L = LVDS P = LVPECL M = LVDS (pin 2 E/D) Q = LVPECL (pin 2 E/D) X = HCMOS (comp 2nd Output) 5 = 5 x 3.2mm 7 = 7 x 5mm 3 = 3.3 V 2 = 2.5 V 0 = ± 100 PPM blank = -20°C to +70°C 5 = ± 50 PPM R = -40°C to +85°C 6 = ± 25 PPM 8 = ± 20 PPM (-20 ~ +70°C) STEP #2: The Fox Customer Service team provides a customer specific Part Number for use on their Bill Of Materials (BOM). Fox Part Number The 1st Field (The assigned Fox Part Number must be on the BOM – not the above Model Description) (This will ensure receipt of the proper part) 7 6 7A – 1 0 6 . 2 5 – 8 Product Code # 767A = FXO–HC52 767 = FXO–HC53 The 3rd Field Fox Internally Generated Number The 2 nd Field The Customer’s Frequency (If any specification changes, the last digits change) (The same specs for a different customer also changes the last digits) This example, FXO-HC526R-106.25 = HCMOS Output, Ceramic 5 x 3.2mm Package, 2.5V, ±25 PPM Stability, -40 to +85°C Temperature Range, at 106.25 MHz Page 2 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Electrical Characteristics Parameters Frequency Range Frequency Stability 1 Symbol FO TO Temperature Range Supply Voltage Input Current (@ 15pF LOAD) Output Load Start-Up Time Output Enable / Disable Time Moisture Sensitivity Level Termination Finish Condition TSTG VDD IDD HCMOS TS MSL Standard operating Optional operating Storage Standard 0.75 ~ 20 MHz 20+ ~ 50 MHz 50+ ~ 100 MHz 100+ ~ 130 MHz 130+ ~ 160 MHz 160+ ~ 180 MHz Standard JEDEC J-STD-20 Maximum Value (unless otherwise noted) 0.750 to 180.000 MHz 100, 50, 25, & 20 ppm -20°C to +70°C -40°C to +85°C -55°C to +125°C 2.5 V ± 5% 22 mA 25 mA 29 mA 32 mA 35 mA 37 mA 15 pF 10 mS 100 nS 1 Au Note 1 – Stability is inclusive of 25°C tolerance, operating temperature range, input voltage change, load change, aging, shock and vibration. Absolute Maximum Ratings (Useful life may be impaired. For user guidelines only, not tested) Operation is only guaranteed for voltage and temperature specifications in Electrical Characteristics section.) Parameters Input Voltage Operating Temperature Storage Temperature Junction Temperature ESD Sensitivity Symbol (unless otherwise noted) Human Body Model –0.5V to +5.0V –55°C to +105°C –55°C to +125°C 150°C > 1 kV VDD TAMAX TSTG HBM Maximum Value Condition Page 3 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Output Wave Characteristics Parameters Symbol Output LOW Voltage VOL Output HIGH Voltage VOH Output Symmetry (See Drawing Below) Output Enable (PIN # 1) Voltage VIH Output Disable (PIN # 1) Voltage VIL Cycle Rise Time (See Drawing Below) TR Cycle Fall Time (See Drawing Below) TF Condition Maximum Value (unless otherwise noted) 0.75 to 160 MHz 160+ to 180 MHz 0.75 to 160 MHz 160+ to 180 MHz @ 50% VDD Level 10% VDD 20% VDD 90% VDD MIN 80% VDD MIN 45% ~ 55% ≥ 70% VDD 0.75 to 160 MHz 160+ to 180 MHz 0.75 to 160 MHz 160+ to 180 MHz ≤ 30% VDD 3.5 nS (10%~90%) 2.5 nS (20%~80%) 3.5 nS (90%~10%) 2.5 nS (80%~20%) If 30% to 70% times are used, Rise and Fall times change to 2 nS from 0.75 to 180MHz If 20% to 80% times are used, Rise and Fall times change to 2.5 nS from 0.75 to 160MHz Rise Time / Fall Time Measurements 10% to 90% 0V to VDD 30% to 70% 20% to 80% 90% - 10% 10% - 90% Rise Time 80 - 20 Times Fall Time Oscillator Symmetry Off Time 1/2 Period On Time 1/2 Period 50% VDD Period Ideally, Symmetry should be 50/50 -- Other expressions are 45/55 or 55/45 Page 4 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified 70 - 30 Times FXO-HC52 Series Phase Noise 0 dBc 2.5V Phase Noise Graphs -10dBc (dBc / Hz) vs. offset frequency -20dBc -30dBc -40dBc -50dBc Data Collected using HP 3048A Four Frequencies from Jitter Tables 156.25MHz -60dBc 62.5 MHz only to 2 MHz offset Equipment Limitation -70dBc 125MHz -80dBc -90dBc -100dBc 62.5 MHz -110dBc -120dBc -130dBc 156.25MHz 62.5 MHz -140dBc -150dBc 106.25 MHz 125MHz -160dBc 10 100 1k 10k Offset Frequency 100k 1M 10M 40M (10Hz to 40MHz) Jitter is frequency dependent. Below are typical values at select frequencies. Phase Jitter & Time Interval Error (TIE) Frequency Phase Jitter TIE (12kHz to 20MHz) (Sigma of Jitter Distribution) Units 62.5 MHz 106.25 MHz 125 MHz 156.25 MHz 2.1 1.2 1.1 0.8 3.1 3.5 2.7 3.7 pS RMS pS RMS pS RMS pS RMS Phase Jitter is integrated from HP3048 Phase Noise Measurement System; measured directly into 50 ohm input; VDD = 2.5V. TIE was measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software; VDD = 2.5V. Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Random & Deterministic Jitter Composition Frequency 62.5 MHz 106.25 MHz 125 MHz 156.25 MHz Random (Rj) Deterministic (Dj) Total Jitter (Tj) (pS RMS) (pS P-P) 1.3 1.4 1.3 1.4 8.4 8.3 6.7 9.7 (14 x Rj) + Dj 27.6 pS 27.7 pS 25.6 pS 29.5 pS Rj and Dj, measured on LeCroy LC684 Digital Storage Scope, directly into 50 ohm input, with Amherst M1 software.Per MJSQ spec (Methodologies for Jitter and Signal Quality specifications) Page 5 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Pin Description and Recommended Circuit Pin # Name Type 1 1 2 3 4 Logic Ground Output Power E/D GND Output VDD Test Points Function 2 Enable / Disable Control of Output (0 = Disabled) Electrical Ground for VDD HCMOS Oscillator Output Power Supply Source Voltage Hi Z N. C. No Connection (Factory Use ONLY) NOTES: 1 2 E/D 1 Includes pull-up resistor to VDD to provide output when the pin (1) is No Connect. Installation should include a 0.01µF bypass capacitor placed between VDD (Pin 4) and GND (Pin 2) to minimize power supply line noise. 4 VDD 0.01 F E/D N. C. TP TP #1 N. C. NC GND 2 VDD #4 GND 3 Output NC #2 OUT #3 HCMOS LOAD (15 pF) Terminations as viewed from the Top NOTE: XPRESSO HCMOS XOs are designed to fit on Industry Standard, 4 pad layouts Enable / Disable Control Pin # 1 (state) Output (Pin # 3) OPEN (No Connection) “1” Level VIH ≥70% VDD “0” Level VIL ≤ 30% VDD ACTIVE Output ACTIVE Output High Impedance Soldering Reflow Profile (2 times Maximum at 260°C for 10 seconds MAX) tp 260°C 225°C Ramp-Up 3°C/s Max 50±10 Seconds Above 225°C Reflow Area 180°C 160°C 10 Seconds Max within 5°C of 260°C peak 120 ± 20 Seconds In Pre-heating Area 25°C 400 Seconds MAX from +25°C to 260°C peak Page 6 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified Ramp Down Not to exceed 6°C/s FXO-HC52 Series Mechanical Dimensional Drawing & Pad Layout 5.15 Max #4 #3 Top View 3.35 Max Actual part marking is depicted. See Traceability (pg. 8) for more information #1 #2 Pin 1 Designator (FOX Head or Dot) 1.4 Max 2.54 1.27 #1 TP* #2 Bottom View 1.2 #4 TP* #3 0.64 Recommended Solder Pad Layout 2.54 1.29 2.25 1.24 Note: XPRESSO HCMOS XOs are designed to fit on industry standard, 4 pad, layouts. Pin Connections #1) E/D #3 Output #2 GND #4 VDD *TP are test points and are NC Drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellations, reference pin shape, etc. may vary Page 7 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Tape and Reel Dimensions 4.0mm Ø1.5mm 7.5mm 5.5mm 16mm 12mm 2.15mm 8.0mm 2k Reel Dimensions in mm 1k Reel Dimensions in mm 2.0 2.0 Ø21.0 Ø13.0 178.0 62.0 120° Ø21.0 Ø13.0 2.0 2.0 255.0 80.0 2.0 17.5 17.5 Labeling (Reels and smaller packaging are labeled with the below) • Fox Part Number: 767-106.25-8 • Quantity: • Description: • Date Code 2000 pieces FXO-HC526R-106.25 0745 FXO-HC526R-106.25 th (YYWW 2007 45 wk) • LOT # 24435 If traceability should become necessary An additional identification code is contained internally if tracking should ever be necessary Page 8 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Traceability – LOT Number & Serial Identification LOT Number The LOT Number has direct ties to the customer purchase order. The LOT Number is marked on the “Reel” label, and also stored internally on non-volatile memory inside the XPRESSO part. XPRESSO parts that are shipped Tape and Reel, are also placed in an Electro Static Discharge (ESD) bag and will have the LOT Number labeled on the exterior of the ESD bag. It is recommended that the XPRESSO parts remain in this ESD bag during storage for protection and identification. If the parts become separated from the label showing the LOT Number, it can be retrieved from inside one of the parts, and the information that can be obtained is listed below: • • • • • Customer Purchase Order Number Internal Fox Sales Order Number Dates that the XPRESSO part was shipped from the factory The assigned customer part number The specification that the part was designed for Serial Identification The Serial ID is the individualized information about the configuration of that particular XPRESSO part. The Serial ID is unique for each and every XPRESSO part, and can be read by special Fox equipment. With the Serial ID, the below information can be obtained about that individual, XPRESSO part: • • • • • • • Equipment that the XPRESSO part was configured on Raw material used to configure the XPRESSO part Traceability of the raw material back to the foundries manufacturing lot Date and Time that the part was configured Any optimized electrical parameters based on customer specifications Electrical testing of the actual completed part Human resource that was monitoring the configuration of the part Fox has equipment placed at key Fox locations World Wide to read the Lot Identification and Serial Number of any XPRESSO part produced and can then obtain the information from above within 24 hours Page 9 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series RoHS Material Declaration Material Name Cover Base Kovar Ceramic + Metallization + Nickel Plating + Gold Plating ＋Seal ring Crystal Content (mg) Content （ｗｔ％） (CAS Number) Nickel (Ni) 1.890 3.09% 7440-02-0 Cobalt (Co) 1.113 1.82% 7440-48-4 Iron (Fe) 3.540 5.78% 7439-89-6 Alumina (Al2O3) 35.484 57.98% 1344-28-1 Silicon Oxide (SiO2) 1.733 2.83% 14808-60-7 Chromium Oxide (Cr2O3) 0.268 0.44% 1308-38-9 Molybdenum Oxide (MoO2) 0.364 0.59% 18868-43-4 Magnesium Oxide (MgO) 0.234 0.38% 1309-48-4 Calcium Oxide (CaO) 0.253 0.41% 1305-78-8 Tungsten (W) 6.290 10.28% 7440-33-7 Molybdenum (Mo) 0.195 0.32% 7439-98-7 Nickel (Ni) 0.810 1.32% 7440-02-0 Cobalt (Co) 0.203 0.33% 7440-48-4 Gold (Au) 0.281 0.46% 7440-57-5 Iron (Fe) 2.438 3.98% 7439-89-6 Nickel (Ni) 1.309 2.14% 7440-02-0 Cobalt (Co) 0.768 1.25% 7440-48-4 Silver (Ag) 1.191 1.95% 7440-22-4 Copper (Cu) 0.210 0.34% 7440-50-8 Aluminum (Al) 0.0021 0.00343% 7429-90-5 Silicon (Si) 0.950 1.55% 7440-21-3 Gold Gold (Au) 0.480 0.784% 7440-57-5 Adhesive Silver (Ag) 0.000210 0.000343% 7440-22-4 Epoxy 0.0000700 0.0001144% 1.170 1.91% ＋silver solder ＩＣ Component ＩＣ Crystal Silicon Dioxide (SiO2) Electrode Silver (Ag) 0.019 0.0310% 7440-22-4 Nickel (Ni) 0.000159 0.000260% 7440-02-0 Silver (Ag) 0.00037 0.000605% 7440-22-4 Silicon (Si) 0.000125 0.000204% 7440-21-3 Adhesive TOTAL 61.196 Page 10 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified 100.00% 14808-60-7 FXO-HC52 Series 3rd Party (SGS) Material Report Page 11 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series 3rd Party (SGS) Material Report (continued) Page 12 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Mechanical Testing Parameter Mechanical Shock Mechanical Vibration High Temperature Burn-in Hermetic Seal Test Method Drop from 75cm to hardwood surface – 3 times 10~55Hz, 1.5mm amplitude, 1 Minute Sweep 2 Hours each in 3 Directions (X, Y, Z) Under Power @ 125°C for 2000 Hours (results below) He pressure: 4 ±1 kgf / cm2 2 Hour soak 2,000 Hour Burn-In Frequency Drift (PPM) Burn-In Testing – under power 2000 Hours, 125°C 10 XpressO HCMOS Burn-In (Power on) Freq = 10MHz, N = 120 5 0 -5 -10 Initial 250 hours 500 hours 1000 hours Page 13 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified 2000 hours FXO-HC52 Series MTTF / FITS Calculations Products are grouped together by process for MTTF calculations. (All XpressO output and package types are manufactured with the same process) Number of Parts Tested: 360 (120 of each output type: HCMOS, LVDS, LVPECL) Number of Failures: 0 Test Temperature: 125°C Number of Hours: 2000 MTTF was calculated using the following formulas: [1.] Device Hours (devhrs) = (number of devices) x (hours at elevated temperature in °K) [2.] MTTF = [3.] FITS = devhrs × af × 2 χ2 1 MTTF Where: Label * 109 Name Formula/Value eV 1 1 ( )×( − ) k t1 t2 e af Acceleration Factor eV Activation Energy 0.40 V k Bolzman’s Constant 8.62 X 10-5 eV/°K t1 Operating Temperature (°K) t2 Accelerated Temperature (°K) Θ Theta Confidence Level (60% industry standard) r Failures Number of failed devices χ2 Chi-Square statistical significance for bivariate tabular analysis [table lookup] based on assumed Θ (Theta – confidence) and number of failures (r) For zero failures (60% Confidence): χ2 = 1.830 DEVICE-HOURS = 360 x 2000 HOURS = 720,000 ( ACCELERATION FACTOR = e 1 1 0.40 ) )×( − 298 398 = 49.91009 8.625 MTTF = 720,000 × 49.91009 × 2 = 39,209,238 Hours 1.833 Failure Rate = 1.833 = 2.55E-8 720,000 × 49.91009 × 2 FITS = Failure Rate *1E9 = 26 Page 14 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified FXO-HC52 Series Notes : For the complete product line of XPRESSO products visit http://www.foxonline.com/xpressomain.htm Patent Numbers: US 6,664,860, US 5,960,403, US 5,952,890; US 5,960,405; US 6,188,290; Foreign Patents: R.S.A. 98/0866, R.O.C. 120851; Singapore 67081, 67082; EP 0958652 China ZL 98802217.6, Malaysia MY-118540-A, Philippines 1-1998-000245, Hong Kong #HK1026079, Mexico #232179 US and Foreign Patents Pending XpressO™ Fox Electronics Fox Hong Kong Fox Japan Tel: +852.2854.4285, Tel:+81.3.3374.2079, (USA)-Worldwide Headquarters Fax:+852.2854.4282 Fax: +81.3.3377.5221 Tel: 888-GET-2-FOX Email: www.foxonline.com/email.htm Email: www.foxonline.com/email.htm Fax:+1.239.693.1554 Fox EMEA Fox Taiwan Email: www.foxonline.com/email.htm Tel/Fax: +44.1767.312632 Tel:+886-2-22073427, Email: www.foxonline.com/email.htm Fax:+886-2-22073486 Contact Information Outside US: +1.239.693.0099, Email: www.foxonline.com/email.htm The above specifications, having been carefully prepared and checked, is believed to be accurate at the time of publication; however, no responsibility is assumed by Fox Electronics for inaccuracies. Page 15 of 15 © 2008 FOX ELECTRONICS | ISO9001:2000 Certified