GENLINX GS9022A TM Digital Video Serializer FEATURES • built-in 75 The GS9022A is a drop-in replacement for the GS9022 in existing applications W cable driver with two serial outputs • standard independent operation The GS9022A is a monolithic bipolar integrated circuit designed to serialize SMPTE 125M and SMPTE 244M bit parallel digital signals as well as other 8 or 10 bit parallel formats. This device performs the functions of sync detection, parallel to serial conversion, data scrambling (using the X9 + X4 +1 algorithm), 10x parallel clock multiplication and conversion of NRZ to NRZI serial data. The data rate is automatically set for SMPTE 259M data rates to 400 Mb/s. Other features include a lock detect output and an internal cable driver capable of driving two 75Ω loads. • space saving 28 pin PLCC package • 650 mW typical power dissipation (data output driving 75 load). W • supports bit rates to 400 Mb/s • accepts 8 bit and 10 bit TTL and CMOS compatible parallel data inputs • fully compatible with SMPTE 259M serial digital standard The device requires a single +5 volt or -5 volt supply and typically consumes 650 mW of power while driving two 75Ω loads. The 28 pin PLCC packaging assures a small footprint for the complete encoder function. • single +5 or -5 volt supply • Pb-free and Green ORDERING INFORMATION APPLICATIONS Part Number Package Temperature Pb-Free and Green • 4ƒSC, 4:2:2 and 360 Mb/s serial digital interfaces for: Video cameras VTRs GS9022ACPJ 28 pin PLCC o°C to 70°C No Signal generators Portable equipment GS9022ACTJ 28 pin PLCC Tape o°C to 70°C No GS9022ACPJE3 28 pin PLCC o°C to 70°C Yes GS9022ACTJE3 28 pin PLCC Tape o°C to 70°C Yes SYNC DETECT DISABLE 25 22 PARALLEL 3-12 DATA IN (10 BITS) INPUT LATCH SYNC DETECT P/S CONVERTER RISE TIME CONTROL 23 SERIAL DATA SERIAL DATA SCRAMBLER NRZ NRZI SCLK PLD PCLK LOOP FILTER PHASE FREQUENCY DETECT 13 CHARGE PUMP MUX VCO 17 DIV BY 2 GENERATOR OSCILLATOR DIV BY 10 GENERATOR GS9022A LOCK DETECT 14 LOCK DETECT 19 RVCO 28 REGULATOR CAP 26 COSC FUNCTIONAL BLOCK DIAGRAM Revision Date: June 2004 Document No. 18325 - 01 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 tel. +1 (905) 632-2996 fax. +1 (905) 632-5946 Web Site: www.gennum.com E-mail: [email protected] NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 DATA SHEET DEVICE DESCRIPTION ABSOLUTE MAXIMUM RATINGS PIN CONNECTIONS PARAMETER VALUE/UNITS 5.5 V PD0 VCC 4 3 2 VCC CREG VEE COSC 28 27 26 PD2 5 25 SYNC DET. DISABLE PD3 6 24 VCCSD 0°C £ TA £ 70°C PD4 7 23 SDO -65°C £ TS £150°C PD5 8 22 SDO PD6 9 21 VEE PD7 10 20 VCC PD8 11 19 RVCO -VEE < VI < VCC Input Voltage Range (any input) DC Input Current (any one input) 10 mA Power Dissipation (VS = 5.25 V) 910 mW Operating Temperature Range Storage Temperature Range GS9022A TOP VIEW 260°C Lead Temperature (soldering 10 seconds) CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION 12 13 PD9 PCK IN 14 15 LOCK VEE DET 16 17 18 VCC LF VEE GS9022A - ENCODER DC ELECTRICAL CHARACTERISTICS VCC = 5V, V EE = 0V, TA = 0°C to 70°C unless otherwise shown PARAMETER SYMBOL CONDITIONS Supply Voltage VS Operating Range Power Consumption PD Supply Current MIN TYP MAX UNITS 4.75 5.0 5.25 V Data outputs driving two 75Ω loads - 650 - mW IS Data outputs driving two 75Ω loads - 160 190 mA TTL Inputs-HIGH VIH TA = 25°C 2.0 - - V TTL Inputs-LOW VIL TA = 25°C - - 0.8 V Logic Input Current IIN - 2.5 6.0 µA TTL Outputs-HIGH VOH TA = 25°C 2.4 - - V TTL Outputs-LOW VOL TA = 25°C - - 0.5 V NOTES TA = 25°C GS9022A - ENCODER AC ELECTRICAL CHARACTERISTICS VCC = 5V, V EE = 0V, T A = 0°C to 70°C, unless otherwise shown PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS NOTES Serial Data Outputs SDATA, SDATA bit rates BRSDO 100 - 400 signal swing VSDO RL = 75Ω 720 800 880 mVp-p rise/fall times tr, tf (20 - 80%) 400 550 800 ps jitter tj 270 Mb/s 240 - ps p-p Note 1 tlock CLoop filt = 0.1µF RLoop filt = 3.9kΩ - 5 - ms Auto Standard 500 - - ps 3 - - ns 3 - - ns Lock Time Mb/s COSC = 0.1µF Parallel Data & Clock Inputs risetime setup hold tR TA = 25°C tSU tHOLD Note 1: Measured using PCLK as trigger source on 1 GHz oscilloscope 18325 - 01 2 of 7 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 Supply Voltage PD1 ≈ GS9022A Digital Video Serializer - Detailed Device Description Functional blocks within the device include the input latches, sync detector, parallel to serial converter, scrambler, NRZ to NRZI converter, internal cable driver, PLL for 10 x parallel clock multiplication and lock detect. The parallel data (PD0-PD9) and parallel clock (PCKIN) are applied via pins 3 through 13 respectively. Sync Detector The Sync Detector looks for the reserved words 000-003 and 3FC-3FF, in ten bit hexadecimal, or 00 and FF in eight bit hexadecimal, used in the TRS-ID sync word. When the occurrence of either all zeros or all ones at inputs PD2-PD9 is detected, the lower two bits PD0 and PD1 are forced to zeros or ones, respectively. This makes the system compatible with eight or ten bit data. For non - SMPTE standard parallel data, a logic input, Sync Detect Disable (25) is available to disable this feature. The charge pump delivers a 'charge packet' to the loop filter which is proportional to the system phase error. Internal voltage clamps are used to constrain the loop filter voltage between approximately 1.8 and 3.4 volts. The VCO, constructed from a current-controlled multivibrator, features operation in excess of 400 Mb/s and a wide pull range (≈ ± 40% of centre frequency). VCO Centre Frequency Selection The wide VCO pull range allows the PLL to compensate for variations in device processing, temperature variations and changes in power supply voltage, without external adjustment. A single external resistor is used to set the VCO current for all standards. The COSC pin is used to configure the VCO of the GS9022A in one of three modes, as shown below: COSC Mode 0.1µF to GND Auto Standard 10k Resistor to VCC ƒ/2 ON 10k Resistor to GND ƒ/2 OFF In auto standard mode, the capacitor sets the sweep rate at which the VCO toggles between ƒ and ƒ/2. Scrambler The Scrambler is a linear feedback shift register used to pseudo-randomize the incoming serial data according to the fixed polynomial (X9+X4+1). This minimizes the DC component in the output serial data stream. The NRZ to NRZI converter uses another polynomial (X+1) to convert a long sequence of ones to a series of transitions, minimizing polarity effects. Phase Locked Loop The PLL performs parallel clock multiplication and provides the timing signal for the serializer. It is composed of a phase/frequency detector, charge pump, VCO , a divide-by-ten counter, and a divide by two counter. The ƒ/2 ON and ƒ/2 OFF modes are used to configure the GS9022A VCO for single standard operation. The lock detect circuit disables the serial data output when the loop is not locked. The Lock Detect output is available from pin 14 and is HIGH when the loop is locked. The true and complement serial data, SDO and SDO are available from pins 22 and 23. These outputs will drive two 75 Ω co-axial cables with SMPTE level serial digital video signals. The phase/frequency detector allows a wider capture range and faster lock time than that which can be achieved with a phase discriminator alone. The discrimination of frequency also eliminates harmonic locking. With this type of discriminator, the PLL can be over-damped for good stability without sacrificing lock time. 3 of 7 18325 - 01 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 The GS9022A Serializer is a bipolar integrated circuit used to convert parallel data into a serial format according to the SMPTE 259M standard. The device encodes both eight and ten bit TTL-compatible parallel signals producing serial data rates up to 400 Mb/s. It operates from a single five volt supply and is packaged in a 28 pin PLCC. GS9022A PIN DESCRIPTIONS SYMBOL TYPE DESCRIPTION 1 VCC Power Supply: Most positive power supply connection for the PLL and Scrambler. 2 VCC Power Supply: Most positive power supply connection for the parallel data inputs and P/S converter. 3-12 PD0-PD9 I TTL level inputs of the parallel data words. PD0 is the LSB and PD9 is the MSB. 13 PCKIN I TTL level input of the parallel clock. 14 LOCK DET O TTL level output which goes high when the internal PLL is locked. 15 VEE Power Supply: Most negative power supply connection. 16 VCC Power Supply: Most positive power supply connection for the PLL and Scrambler. 17 LF 18 VEE 19 RVCO 20 VCC 21 VEE 22, 23 SDO, SDO 24 VCCSD 25 SYNC DET DISABLE I TTL level input that disables the internal sync detector when high. This allows the GS9022 to serialize 8 or 10 bit non-SMPTE standard parallel data. 26 COSC I Toggles VCO between ƒ and ƒ/2. 27 VEE I Power Supply: Most negative power supply connection. 28 CREG I 18325 - 01 I Connection for the R-C loop filter components. Power Supply: Most negative power supply connection. I VCO frequency setting resistor. A 1% resistor is required. Power Supply: Most positive power supply connection for the PLL and Scrambler. Power Supply: Most negative power supply connection. I 75 Ω cable driver outputs (true and inverse). Power Supply: Most positive power supply for cable driver outputs. Compensation capacitor for internal voltage regulator that requires decoupling with a 0.1 µF capacitor located as close as possible to the pin in series with an 820 Ω Resistor. 4 of 7 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 PIN NO. INPUT / OUTPUT CIRCUITS VCC 1k 1k 10k VR1 PINS 3-12 13, 25 LOCK DETECT PIN 14 VEE VEE Fig. 1 Sync Detect Disable, Parallel Data, Parallel Clock Fig. 2 Lock Detect VCC VCC 400 400 tCLKL = tCLKH 50% PARALLEL CLOCK PLCK VOUT PIN 22 PARALLEL DATA PDn VCC tSU tHOLD Fig. 4 Input Clock / Data Timing VOUT PIN 23 Fig. 3 Output Circuit 5 of 7 18325 - 01 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 VCC TYPICAL PERFORMANCE CURVES (VS = 5V, TA = 25° C unless otherwise shown) RVCO =2.2k 350 800 SERIAL OUTPUT (mV) Auto Standard Mode JITTER p-p (ps) 300 250 200 150 790 780 770 100 50 760 50 100 150 200 250 300 350 400 450 0 10 DATA RATE (Mbps) 40 50 60 70 Fig. 6 Serial Data Output Level vs Temperature 600 3.1 RVCO =2.2k 550 360 Mbps 3.0 500 LOOP FILTER VOLTAGE (V) VCO FREQUENCY (MHz) 30 AMBIENT TEMPERATURE (°C) Fig. 5 Output Jitter ƒ/2 OFF 450 400 350 300 250 ƒ/2 ON 200 150 100 2.6 143 Mbps 2.5 2.3 2.4 2.6 2.8 3.0 3.2 3.4 Auto Standard Mode 2.7 2.4 2.2 RVCO =2.2k 2.8 0 2.0 177 Mbps 2.9 50 270 Mbps 0 10 20 30 40 50 60 TEMPERATURE (°C) TYPICAL LOOP FILTER VOLTAGE (V) Fig. 8 Loop Filter Voltage vs Temperature Fig. 7 VCO Frequency vs Loop Filter Voltage 18325 - 01 20 6 of 7 70 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 810 400 APPLICATION CIRUIT VCC + 0.1 10 5k 1 2 16 20 VCC VCC VCC DATA 0 100 3 100 4 100 5 100 6 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 100 7 100 8 100 DATA 6 DATA 7 10 100 11 100 12 DATA 8 DATA 9 CLOCK 100 13 VCC 14 VCCSD PD 0 PD 1 PD 2 PD 3 PD 4 25 L O C K S Y N SDO C D E T E C T D I S 1.0 22 68 75 1p8 23 1.0 68 150 1p8 SDO 150 PD 5 9 100 24 75 GS9022A PD 6 VCC PD 7 PD 8 1M PD 9 17 C R E G PCK IN 10pF VEE 15 VEE VEE 18 21 VEE 27 28 R V C O C O S C 26 LF 3.9k 19 0.1 0.1 All resistors in ohms, all capacitors in microfarads unless otherwise stated. 820Ω 0.1 0.1 2k2 1% Fig. 9 GS9022A Application Circuit REVISION NOTES: DOCUMENT IDENTIFICATION: DATA SHEET Added lead-free and green information. The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. For latest product information, visit www.gennum.com GENNUM CORPORATION GENNUM JAPAN CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax +1 (905) 632-2814 Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED Tel: +44 (0) 1252 747000 Fax: +44 (0) 1252 726523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. © Copyright May 2001 Gennum Corporation. All rights reserved. 7 of 7 Printed in Canada. 18325 - 01 NOT RECOMMENDED FOR NEW DESIGNS SEE GS9032 Figure 9 shows a typical application circuit of the GS9022A driving a 75Ω cable.