Global Mixed-mode Technology Inc. G569C CD-RW Laser Diode Current Driver Features General Description The G569C is a single chip solution for the various functions relating to laser diode operation in a CD-RW drive. The G569C integrates nine functional blocks in one chip. It has five voltage-to-current converters, one current-to-voltage converters which is called FSA, one OP-AMP, one eight-channels D/A converter, and one voltage subtracter with output clamping capability called Dalpha. Single +5V supply Laser diode read current driver Laser diode write current driver Laser diode Erase current driver Deltap circuit to control write current FSA circuit to integrate photo diode current Cagain circuit to convert Vcagain into current Dalpha circuit to perform voltage subtraction and limiting 3-wire interface to control internal DAC A build-in OP-AMP 48-pin SSOP package Three of the five V-to-I converters provide the laser diode currents for Read, Write, and Erase operations, respectively; another one of the V-I converters provides the Cagain current; and the other one provides Deltap current which can selectively shunt a certain amount of laser diode current for write operation. For the Write and Erase operations, the voltage to current conversion ratio can be adjusted using an external or internal DAC resistor array. The FSA circuit performs integration on the output current of an external photo diode, and sample-and-hold the peak voltage. It is used to monitor the laser diode power. The internal eight-channel D/A converter is used to provide the input voltage for above functional blocks. The G569C is available in a 48-pin SSOP surface-mount package. Applications CD-RW Drive Pin configuration Ordering Information G569C IW_IN 1 48 WDB LS_DELTA TST1 2 47 3 46 LS_WRITE PWRITE LD PWO 4 45 DALPHA 5 44 DI PWO_I 6 43 CLK PWB 7 42 VSS PWMAX PWMIN 8 9 41 40 VOUT VI- /RESET 10 11 39 38 VI+ VDD 12 13 37 36 FSOF FSWS FSCLR VSS EDB LS_ERASE PERASE 14 35 RECORD 15 34 FSW CDR 16 33 IFSA FSR S2V9 17 32 CAGAIN2 18 31 FSRS CAGS_I 19 30 VDD DCAGAIN 20 29 CAGAIN RCAGAIN1 21 28 SELN4_IN PR_I 22 27 23 24 26 RCAGAIN2 PRFINE 25 ORDER ORDER NUMBER NUMBER (Pb free) G569CS8U G569CS8Uf Note: S8: SSOP-48 U: Tape & Reel TEMP. RANGE PACKAGE 0°C to 85°C SSOP-48 LS_READ IR PRCOARSE SSOP-48 TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 1 G569C Global Mixed-mode Technology Inc. Absolute Maximum Ratings derate .7mW/°C about 70°C)…………….……… 695mW Operating Temperature Range…….…-10°C to +100°C Junction Temperature……………………...…….+150°C Storage temperature Range…….…….-65°C to +165°C Reflow Temperature (soldering, 10sec)………..+260°C VCC to GND…………………………….……..-0.3V to +6V Dalpha to GND………………………………....-3V to +6V All other pin to GND…………………………-0.3V to +6V ESD protetion (human body model)………………2000V Continuous power dissipation (TA=70°C), Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Recommended Operating Conditions PARAMETER SYMBOL MIN TYP MAX UNITS Supply voltage High-level input voltage VDD VIH 4.75 2 5 5.5 V V Low-level input voltage Operating free-air temperature VIL TA 0 0.8 70 V °C Electrical Characteristics (VCC = 5V, TA = 0°C to +70°C, unless otherwise noted) MIN TYP MAX UNITS Supply voltage range PWO output voltage Dalpha input voltage PARAMETER CONDITIONS 4.75 0 -3.0 5.0 5.5 VS2V9 3.5 V V V PWO_I input voltage PWB output voltage 0 0 1.5 VS2V9 V V PWMAX output voltage PWMIN output voltage 0 0 VS2V9 VS2V9 V V 130 mA IE output current S2V9 input voltage 0 VS2V9 2.9 Cagain output current 0 V 1.2 mA PRFine output voltage 0 VS2V9 V PRCoarse output voltage 0 VS2V9 V IR output current 0 160 mA PR_I input voltage 0 2.16 V FSR output voltage 0 3.0 V FSW output voltage 0 3.0 V VI- input voltage 0 3.5 V VI+ input voltage 0 3.5 V IW output current 0 160 mA Operation current 41 mA TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 2 Global Mixed-mode Technology Inc. G569C Pin Description PIN NO. PIN NAME I/O 1 IW_IN I 2 3 4 5 6 7 8 9 10 11,42 12 13 14 15 16 17 LS_DELTA TST1 PWO DALPHA PWO_I PWB PWMAX PWMIN /RESET VSS EDB LS_ERASE PERASE RECORD CDR S2V9 O I O I I O O O I I O I O I I I 18 19 20 21 22 23 24 25 26 27 28 29 CAGAIN2 CAGS_I DCAGAIN CAGAIN RCAGAIN1 RCAGAIN2 PRFINE PRCOARSE IR LS_READ PR_I SELN4_IN O I O O O O O O O I I I 30,38 31 VDD FSRS I I 32 33 FSR IFSA O I 34 35 36 FSW FSCLR FSWS O O I 37 FSOF I 39 40 41 43 44 45 46 47 48 VI+ VIVOUT CLK DI LD PWRITE LS_WRITE WDB I I O I I I O I O PIN FUNCTION A diode of type BAS216 should be connected between this pin and node IW. This pin provides the path for sinking IW current. Connect a 10Ω resistor from this pin to VSS Test pin. Connect to ground for normal operation. DAC output, connect to PWO_I through a resistor divider Control voltage input Control voltage input Voltage output Voltage output Voltage output Logic input. A Low on this pin reset all DAC latches to 0. Ground pin Connect to the base node of external PNP BJT (Type BC808). Connect a 6.8Ω (1206 type) resistor from this pin to VDD Connect a DAC resistor array from this pin to VSS Logic input, a high indicates in recording mode. Logic input, a high indicates in CD-R mode. Voltage input. Contribute to current output on CAGAIN pin and provides internal DAC reference voltage. Tristate output. Connect 62KΩ to pin CAGAIN. Logic input, 0~2V swing. An optional resistor may be added to modify the output current on CAGAIN Current output A 16.2KΩ resistor should be connected from this pin to VSS A 3.9KΩ resistor should be connected from this pin to VSS DAC output, connect to PR_I through a resistor divider DAC output, connect to PR_I through a resistor divider Read current output for laser diode Connect two 22Ω (1206 type) resistors from this pin to VDD Voltage input which controls the current on IR pin Logic input. This pin can be shorted to pin CDR or be connected to the voltage divider formed by CDR and SELN4. Supply voltage input. Each VDD pin should have a 0.1µF bypass capacitor to VSS. Logic input, when FSRS=1, the voltage on pin FSCLR is sampled onto pin FSR, else FSR is in hold mode. Sampled voltage output, controlled by FSRS If internal integration control circuitry is used, connect a photo diode from this pin to +30V. connect it to VDD otherwise Sampled voltage output, controlled by FSWS Sampling capacitors and resistor are connected to this pin. Logic input, when FSWS=1, the voltage on pin FSCLR is sampled onto pin FSW, else FSW is in hold mode. If internal integration control circuitry is used, connect the control signal to this pin. A logic low enable the current charging on the capacitors on pin FSCLR with the current from IFSA. Connect this pin to VDD if internal integration control circuitry is not used. Non-inverting input of Op Amp Inverting input of Op Amp Op Amp output Clock input of I2S bus Data input of I2S bus Latch data input of I2S bus Connect a DAC resistor network from this pin to VSS Connect a 6.8Ω (1206type) from this pin to VDD Connect to the base node of external PNP BJT. (Type BC807-40) TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 3 G569C Global Mixed-mode Technology Inc. Detail Description The typical application circuit of G569C is shown in Fig. 1. The block diagram of G569C is shown in Fig. 2. It contains nine circuit blocks. The operation of these blocks is described below. programming of the OTA's transconductance. An internal DAC can be enabled through I2S bus to replace the external DAC resistor array. The maximum RPWRITE is 7.5KΩ. The maximum IW is 130 mA. Since IW must flow through the external 6.8Ω resistors connected between VDD and LS_WRITE pin, type 1206 SMD resistors must be used to handle the power dissipation. READ Block This block is equivalent to an operational transconductance amplifier (OTA). The voltage on PR_I pin is the input voltage, VPR_I; the output current, IR, is delivered on pin IR. The relationship between VPR_I and IR is given by: DELTAP Block This block is a current sink used to selectively sink the IW current. When DP4 is low, the current sink reduces the output current on IW by the amount of the magnitude of the current sink. The magnitude of the current sink, Is, is given by: IR = 820 x VPR_I /( R232 ∥R233) where IR is in mA, VPR_I is in volt, and R is in Ω. The recommended values for R232 and R233 are 22Ω, the maximum VPR_I is 2.16 V, thus the maximum IR is 160mA. Since IR must flow through the two external 22Ω resistors connected between VDD and LS_READ pin, type 1206 SMD resistors must be used to handle the power dissipation. Is = DALPHA Block The function of this block is a voltage subtracter. The voltage on pin PWB, VPWB, is given by: VPWB 1800 x VPWD / RPERASE, R235 = 2 x VPWO_I - VDALPHA, where VPWO_I and VDALPHA are the voltages on pins PWO_I and DALPHA, respectively. In addition, the magnitude of the output voltage VPWB is limited by VPWMAX and VPWMIN, which are the voltages on pins PWMAX and PWMIN. where IE is in mA, VPWD is in volt, and RPERASE, in KΩ, is the total resistance from pin PEARSE to ground. Typically, a digital-to-analog converter (DAC) resistor array is connected at PERASE pin to allow digital programming of the OTA's transconductance. The maximum RPERASE is 7.5KΩ. An internal DAC can be enabled through I2S bus to replace the external DAC resistor array. The maximum IE is 130 mA. Since IE must flow through the external 6.8Ω resistors connected between VDD and LS_ERASE pin, type 1206 SMD resistors must be used to handle the power dissipation. When 2xVPWO_I - VDALPHA < VPWMIN, then VPWB = VPWMIN. When 2xVPWO_I - VDALPHA, > VPWMAX, then VPWB = VPWMAX. The input voltage ranges of VPWMAX and VPWMIN are 0 to VS2V9 which is the voltage input at S2V9 pin, and the condition VPWMAX > VPWMIN must hold. Note that the input voltage range of VDALPHA is -3V to +3.5V. CAGAIN Block This block is also an operational transconductance amplifier (OTA). The voltage on VCAGAIN pin is the input voltage, VVCAGAIN; the output current, ICAGAIN, is delivered on pin CAGAIN. Let the voltages on pins CDR, CAGS, CAGAIN and S2V9 be denoted as VCDR, VCAGS, VCAGAIN, VS2V9, respectively. The relationship between VVCAGAIN and ICAGAIN is given by: WRITE Block This block is also an operational transconductance amplifier (OTA). The voltage on PWD node is the input voltage, VPWD; the output voltage, VWDB, can be used to drive an external PNP BJT to provides desired IW current. The relationship between VPWD and IW is given by: IW = x VDELTAP / RLS_DELTA, where Is is in mA; VDELTAP, in volt, is an internal DAC output; and RLS_DELTA, in KΩ, is the resistance from pin LS_DELTA to ground. Type 1206 SMD resistors must be used for RLS_DELTA to handle the power dissipation. When DP4 is high, the current output on IW current is not affected. ERASE Block This block is also equivalent to an operational transconductance amplifier (OTA). The voltage on PWD node is the input voltage, VPWD; the output voltage, VEDB, can be used to drive an external PNP BJT to provides desired IE current. The relationship between VPWD and IE is given by: IE = 3 20 1800 x VPWD / RPWRITE, R234 When VCDR = 5V, VCAGS = 5V ICAGAIN = 1.2 x VCAGAIN / (R108 ∥ R109) + (VS2V9 VCAGAIN) / R195, where IW is in mA, VPWD is in volt, and RPWRITE, in KΩ is the total resistance from pin PWRITE to ground. Typically, a digital-to-analog converter (DAC) resistor array is connected at PWRITE pin to allow digital When VCDR = 5V, VCAGS = 0V ICAGAIN = (VS2V9 - VCAGAIN) / R195 TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 4 Global Mixed-mode Technology Inc. G569C When VFSOF = 0V, the FSCLR pin is charged by IFSA. When VCDR = 0V, VCAGS = 5V, VRECORD = 0V ICAGAIN = 1.2 x VCAGAIN / R108 + (VS2V9 - VCAGAIN) / R195, When VFSOF = 5V, the FSCLR pin is not charged by IFSA. When VCDR = 0V, VCAGS = 5V, VRECORD = 5V ICAGAIN = 1.2 x VCAGAIN / R108 The FSCLR, RDGAIN1, RDGAIN2, and RDGAIN3 pins are driven by an open-drain buffer, i.e., the voltages on these pins are either 0V or Hi-Z. The capacitance values of the three capacitors connecting to the FSCLR may need to be changed if loader other than CDL4800 is used. When VCDR = 0V, VCAGS = 0V, VRECORD = 0V ICAGAIN = (VS2V9 - VCAGAIN) / R195, When VCDR = 0V, VCAGS = 0V, VRECORD = 5V ICAGAIN = 0 mA, When VFSCLR = 0V, the charges on the capacitors are discharged to 0V. Where ICAGAIN is in mA; all voltages are in volt, and all resistance are in KΩ. When VFSCLR = Hi-Z, the charging of FSCLR node is allowed. FSA Block The FSOF/FSON control the integration of the photodiode current, IFSA, on the capacitors connected on pin FSCLR to obtain a voltage. The voltage on FSCLR pin is connected to two sample-and-hold circuit. The voltages sampled by the control voltage on FSWS and FSRS pins are output on FSW and FSR pins, respectively. Namely, When VRDGAIN1 = 0V, the VFSCLR is given by: VFSCLR = IFSA x R187. When VRDGAIN1 = Hi-Z, the charging of FSCLR node is allowed. When VRDGAIN2 = 0V, the capacitor C123 is in parallel with C116. When VFSWS = 5V, VFSW = VFSCLR, When VRDGAIN2 = Hi-Z, the capacitor C123 has no effect. When VFSWS = 0V, VFSW = the previously sampled value; When VRDGAIN3 = 0V, the capacitor C117 is in parallel with C116. When VFSRS = 5V, VFSR = VFSCLR, When VRDGAIN3 = Hi-Z, the capacitor C117 has no effect. When VFSRS = 0V, VFSR = the previously sampled value. The charging of FSCLR node is controlled by signals VFSOF and VFSON. TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 5 G569C Global Mixed-mode Technology Inc. 5V 5V IFSA FSOF 30V 5V CAGAIN CAGAIN (pin 21) R195 RCAGAIN2 (pin 23) 3.9K CDR 820 R187 IFSA (pin 33) 22K VRDGAIN1 FSCLR(pin 35) FSCLR (pin 35) C123 2.2nF C116 560pF SELN4_IN (pin 29) 10K C117 1.5nF VRDGAIN3 VRDGAIN2 R67 CAGS FSON CDR (pin 16) 100K SELN4 BF824 820 0.1μF RCAGAIN1 (pin 22) 16.2K R109 R70 VDD (pin 30,38) CAGAIN2 (pin 18) 62K R108 R69 100 R68 R71 100 CAGS_I (pin 19) 330 12V C113 330pF R66 220 R234 (1206) LS_WRITE (pin 47) 5V R230 4.7K R231 PRCOARSE (pin 25) R210 WDB (pin 48) PRFINE (pin 24) 150K R302 2.2K 6.8 47 PR_I (pin 28) IW_IN (pin 1) R192 330 R124 270 5V BC847B R232 (1206) 22 22 R232 (1206) DP4 PWRITE (pin 46) C52 68pF LS_READ (pin 27) TST1 (pin 3) IR 5V R235 12V 6.8 (1206) R226 1.5K BC807_40 IW BAS216 5V R229 6.8K C127 100nF R191 220 R36 1M IR (pin 26) LS_DELTA (pin 2) R236 10 (1206) LS_ERASE (pin 13) R236 R92 220 PWO (pin 4) C135 100nF 150K EDB (pin 12) BC808 150K PERASE (pin 14) R127 R211 47 IE PWO_I (pin 6) 5V R96 1M FSOF (pin 37) C53 1nF FSOF VSS (pin 11,42) Fig 1. Typical application circuit Note: The circuits in the dotted-line are the suggested circuit when internal integration circuit is not used. Please refer to pin description for details. TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 6 Ver: 1.0 Oct 02, 2000 7 SELN4_IN CAGAIN2 RCAGAIN2 RCAGAIN1 DCAGAIN LS_DELTA TST1 IW_IN WDB LS_WRITE PWRITE PERASE LS_ERASE EDB LD DI CLK /RESET (pin 29) (pin 18) (pin 23) (pin 22) (pin 20) (pin 2) (pin 3) (pin 1) (pin 48) (pin 47) (pin 46) (pin 14) (pin 13) (pin 12) (pin 45) (pin 44) (pin 43) (pin 10) DELTAP WRITE Internal DAC Resistor Array (CH9) Internal DAC Resistor Array (CH10) ERASE CDR (pin 16) VDELTAP D/A (pin 24) (pin 25) (pin 4) RECORD (pin 15) CAGS_I (pin 19) CAGAIN PWD CAGAIN (pin 21) VCAGAIN LS_READ (pin 27) VOUT (pin 41) (pin 40) (pin 39) (pin 31) (pin 36) (pin 37) (pin 35) (pin 33) (pin 32) IR (pin 26) (pin 8) (pin 9) REF CH 7 OUT FSA (pin 5) (pin 6) (pin 34) READ DALPHA PR_I (pin 28) PWB (pin 7) REF CH 8 OUT REF CH 3 OUT REF CH 2 OUT REF CH 1 OUT REF CH 6 OUT REF CH 4 OUT REF CH 5 OUT S2V9 (pin 17) VI- VI+ FSRS FSWS FSOF FSCLR IFSA FSR FSW PRFINE PRCOARSE PWO PWMIN PWMAX PWO_I DALPHA Global Mixed-mode Technology Inc. G569C Fig 2. Block Diagram of G569C TEL: 886-3-5788833 http://www.gmt.com.tw G569C Global Mixed-mode Technology Inc. Internal DAC Digital Format 12BIT SERIAL DATA DATA 1 2 3 4 5 6 7 8 9 10 11 (LSB) 12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 D1 D2 D3 D4 D5 D6 D7 : DAC DATA CLK Data Assignment D0 (LSB) D8 (MSB) D9 D10 (MSB) D11 : DAC SELECT DATA (LSB) DAC Select Data D8 D9 D10 D11 0 0 0 0 0 0 0 1 Don’t Care PRCOARSE Selection DAC Selection 0 0 0 0 0 1 1 1 0 0 1 0 PRFINE Selection VCAGAIN Selection PWMIN Selection 0 1 0 1 PWMAX Selection 0 0 1 1 1 1 0 1 PWO Selection DELTAP Selection 1 1 1 0 0 0 0 0 1 0 1 0 PWD Selection WRITE Selection ERASE Selection 1 1 0 1 1 0 1 0 Don’t Care Don’t Care 1 1 1 1 0 1 1 0 Don’t Care Don’t Care 1 1 1 1 Don’t Care Digital Data Format for Internal DAC D0 D1 D2 D3 D4 D5 D6 D7 0 0 0 0 0 0 0 0 DAC Output 0 1 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VIN / 256 × 1 VIN / 256 × 2 VIN / 256 × 3 ¦ 1 ¦ 1 ¦ 1 ¦ 1 ¦ 1 ¦ 1 ¦ 1 ¦ 1 ¦ VIN / 256 × 255 Digital Data Format for WRITE and ERASE D0 D1 D2 D3 D4 D5 D6 D7 0 1 × 0/1 × 0/1 × 0/1 × 0/1 × 0/1 × 0/1 × 0/1 Comments Disable Internal R2R Network Enable Internal R2R Network D1 is LSB , D7 is MSB TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 8 G569C Global Mixed-mode Technology Inc. Timing Chart R LSB MSB DI D11 D10 D0 D9 CLK LD VO *Input data carried out LD signal Low besides CLK signal positive edge. CLK, LD is keep generally HIGH level. AC Characteristics Symbol Parameter Measurement Condition Limit Unit tCKL Clock “L” Pulse Width 200 nS tCKH tCR Clock “H” Pulse Width Clock Rise Time 200 nS tCF tDCH tCHD Clock Fall Time Data Set Up Time Data Hold Time 60 100 nS nS tCHL LD Set Up Time 200 nS tLDC tLDH LD Hold Time LD “H” Pulse Duration Time 100 100 nS nS tDo tLDD Data Output Delay Time D-A Output Setting Time 200 CL=100pF CL ≤ 100pF,VAO:0.1< = > 2.6V This Time Until The Output Becomes The final Value Of 1/2 LSB 70 nS 350 nS 300 µS Timing Chart t CR t CF t CKH CLK t CKL t LDC DI t DCH t CHD t LDH t CHL LD t LDD D-A OUTPUT t Do Do OUTPUT TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 9 G569C Global Mixed-mode Technology Inc. Package Information C L E1 E h x 45° θ D A A1 0.004 C SEATING PLANE e b MIN. DIMENSION IN MM NOM. MAX. MIN. DIMENSION IN INCH NOM. A 2.413 2.591 2.794 0.095 0.102 0.110 A1 b 0.203 0.203 0.305 0.406 0.343 0.008 0.008 0.012 0.016 0.0135 c D 0.127 15.75 0.254 16.00 0.005 0.620 e E E1 10.033 7.391 10.668 7.595 0.395 0.291 0.635 1.016 θ 0.015 1.020 SYMBOL h L θ 15.88 0.635 BASIC 0.381 0.508 0 7.493 MAX. 0.010 0.630 0.625 0.025 BASIC 0 0.295 0.420 0.289 0.025 0.040 θ TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 10 Global Mixed-mode Technology Inc. G569C Package Description: SSOP-48 Quantity /Reel Reel Diameter Carrier Tape (Width) Carrier Tape (Pitch) : : : : 1000 / Reel 13” 32mm 16mm Mechanical Polarization Top View Shown With Cover Tape Removed EIA-JEDEC SO Package Outline Style Termination No.1 User Direction of Feed GMT Inc. does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and GMT Inc. reserves the right at any time without notice to change said circuitry and specifications. TEL: 886-3-5788833 http://www.gmt.com.tw Ver: 1.0 Oct 02, 2000 11