HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Typical Applications Features Low noise wideband MMIC VCO for applications such as: Wide Tuning Bandwidth • Industrial/Medical Equipment Low SSB Phase Noise: -95 dBc/Hz @100 kHz • Test & Measurement Equipment No External Resonator Needed • Military Radar, EW & ECM Single Positive Supply: +5V @ 55 mA Pout: +5 dBm RoHS Compliant 4 x 4 mm SMT Package Functional Diagram General Description The HMC587LC4B is a wideband GaAs InGaP Voltage Controlled Oscillator which incorporates the resonator, negative resistance device, and varactor diode. Output power and phase noise performance are excellent over temperature due to the oscillator’s monolithic construction. The Vtune port accepts an analog tuning voltage from 0 to +18 volts. The HMC587LC4B VCO operates from a single +5V supply, consumes only 55 mA of current, and is housed in a RoHS compliant SMT package. This wideband VCO uniquely combines the attributes of ultra small size, low phase noise, low power consumption, and wide tuning range. VCOs & PLOs - SMT 9 Electrical Specifications, TA = +25° C, Vcc = +5V Parameter Min. Frequency Range Power Output 0 Typ. Units 5.0 - 10.0 GHz 5 dBm SSB Phase Noise @ 100 kHz Offset -95 dBc/Hz SSB Phase Noise @ 10 kHz Offset -65 dBc/Hz Tune Voltage (Vtune) 0 18 V Supply Current (Icc) (Vcc = +5.0V) 40 75 mA 10 μA Tune Port Leakage Current (Vtune = +18V) Output Return Loss 2nd Harmonic 9 - 166 Max. 7 dB -15 dBc Pulling (into a 2.0:1 VSWR) 4 MHz pp Pushing @ Vtune= +5V 15 MHz/V Frequency Drift Rate 0.8 MHz/°C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Frequency vs. Tuning Voltage, T= 25°C 12 12 11 11 OUTPUT FREQUENCY (GHz) 10 9 8 7 6 +25 C +85 C -40 C 5 10 9 8 7 6 Vcc= 4.75V Vcc= 5.00V Vcc= 5.25V 5 4 4 0 2 4 6 8 10 12 14 16 18 20 0 2 4 TUNING VOLTAGE (VOLTS) 600 10 500 8 OUTPUT POWER (dBm) SENSITIVITY (MHz/VOLT) 10 12 14 16 18 20 16 18 20 Output Power vs. Tuning Voltage, Vcc= +5V 400 300 200 +25 C +85 C -40 C 6 4 2 0 +25 C +85 C -40 C -2 -4 0 0 2 4 6 8 10 12 14 16 18 0 20 TUNING VOLTAGE (VOLTS) 9 2 4 6 8 10 12 14 TUNING VOLTAGE (VOLTS) Typical SSB Phase Noise @ Vtune= +5V SSB Phase Noise vs. Tuning Voltage 0 0 -20 SSB PHASE NOISE (dBc/Hz) SSB PHASE NOISE (dBc/Hz) 8 TUNING VOLTAGE (VOLTS) Sensitivity vs. Tuning Voltage, Vcc= +5V 100 6 VCOs & PLOs - SMT OUTPUT FREQUENCY (GHz) Frequency vs. Tuning Voltage, Vcc = +5V 10 kHz 100 kHz -40 -60 -80 -100 -120 0 2 4 6 8 10 12 14 TUNING VOLTAGE (VOLTS) 16 18 20 -20 -40 -60 -80 -100 -120 2 10 3 10 4 10 5 10 6 10 OFFSET FREQUENCY (Hz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 167 HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Absolute Maximum Ratings Vcc VCOs & PLOs - SMT 9 +5.5 Vdc Vtune 0 to +22V Junction Temperature 135 °C Continuous Pdiss (T = 85°C) (derate 12.5 mW/°C above 85°C) 625 mW Thermal Resistance (junction to ground paddle) 80 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA 2. LEAD AND GROUND PADDLE PLATING: GOLD FLASH OVER Ni. 3. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 9 - 168 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Pin Descriptions Pin Number Function Description 1 - 3, 5 - 11, 13, 17 - 24 N/C No Connection. These pins may be connected to RF/DC ground. Performance will not be affected. 4 Vtune Control Voltage and Modulation Input. Modulation bandwidth dependent on drive source impedance. See “Determining the FM Bandwidth of a Wideband Varactor Tuned VCO” application note. Interface Schematic 12 Vcc Supply Voltage Vcc= +5V 14, 16 GND Package bottom has an exposed metal paddle that must also be RF & DC grounded. 15 RFOUT RF output (AC coupled) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com VCOs & PLOs - SMT 9 9 - 169 HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Evaluation PCB VCOs & PLOs - SMT 9 List of Materials for Evaluation PCB 108648 [1] Item Description J1 PCB Mount SMA RF Connector, Johnson J2 PCB Mount SMA Connector, SRI J3 DC Header C1 1000 pF Capacitor, 0402 Pkg. C2 4.7 μF Capacitor, Tantalum U1 HMC587LC4B VCO PCB [2] 108646 Eval Board [1] Reference this number when ordering complete evaluation PCB The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed ground paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [2] Circuit Board Material: Rogers 4350 9 - 170 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC587LC4B v00.1105 WIDEBAND MMIC VCO w/ BUFFER AMPLIFIER, 5 - 10 GHz Notes: VCOs & PLOs - SMT 9 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 171