HOLTEK HT49R70A-1

HT49R70A-1/HT49C70-1/HT49C70L
LCD Type 8-Bit MCU
Technical Document
· Tools Information
· FAQs
· Application Note
- HA0017E Controlling the Read/Write Function of the HT24 Series EEPROM Using the HT49 Series MCUs
- HA0024E Using the RTC in the HT49 MCU Series
- HA0025E Using the Time Base in the HT49 MCU Series
- HA0026E Using the I/O Ports on the HT49 MCU Series
- HA0027E Using the Timer/Event Counter in the HT49 MCU Series
Features
· Operating voltage:
· Buzzer output
fSYS=4MHz: 2.2V~5.5V for HT49R70A-1/HT49C70-1
fSYS=8MHz: 3.3V~5.5V for HT49R70A-1/HT49C70-1
fSYS=500kHz: 1.2V~2.2V for HT49C70L
· On-chip crystal, RC and 32768Hz crystal oscillator
· HALT function and wake-up feature reduce power
consumption
· 8 input lines
· 16-level subroutine nesting
· 16 bidirectional I/O lines
· Bit manipulation instruction
· Two external interrupt input
· 16-bit table read instruction
· One 8-bit and one 16-bit programmable timer/event
· Up to 0.5ms instruction cycle with 8MHz system clock
counter with PFD (programmable frequency divider)
function
for HT49R70A-1/HT49C70-1
· Up to 8ms instruction cycle with 500kHz system clock
· LCD driver with 41´2, 41´3 or 40´4 segments
for HT49C70L
· 8K´16 program memory
· 63 powerful instructions
· 224´8 data memory RAM
· All instructions in 1 or 2 machine cycles
· Real Time Clock (RTC)
· Low voltage reset/detector functions for
· 8-bit prescaler for RTC
HT49R70A-1/HT49C70-1
· Watchdog Timer
· 100-pin QFP package
General Description
The advantages of low power consumption, I/O flexibility, programmable frequency divider, timer functions,
oscillator options, HALT and wake-up functions and
buzzer driver in addition to a flexible and configurable
LCD interface, enhance the versatility of these devices
to control a wide range of LCD-based application possibilities such as measuring scales, electronic multimeters, gas meters, timers, calculators, remote
controllers and many other LCD-based industrial and
home appliance applications.
The HT49R70A-1/HT49C70-1/HT49C70L are 8-bit,
high performance, RISC architecture microcontroller
devices specifically designed for a wide range of LCD
applications. The mask version HT49C70-1 and
HT49C70L are fully pin and functionally compatible with
the OTP version HT49R70A-1 device. The HT49C70L
is a low voltage version, with the ability to operate at a
minimum power supply of 1.2V, making it suitable for
single cell battery applications.
Rev. 2.00
1
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Block Diagram
P ro g ra m
M e m o ry
IN T C
In s tr u c tio n
R e g is te r
M
M P
M
T M R 1 C
T M R 1
P F D 1
U
X
D A T A
M e m o ry
U
P B 3 /T M R 1
T M R 0 O V
X
M
P C
fT
1 D
Y S
/4
U
R T C
X
O S C
O S C 3
O S C 4
P C 0 ~ P C 7
P O R T B
P B 0 /IN T 0
P B 1 /IN T 1
P B 2 /T M R 0
P B 3 /T M R 1
P B
S h ifte r
Y S
W D T O S C
S T A T U S
A L U
fS
T im e B a s e O u t
fS
W D T
M U X
T im in g
G e n e r a tio n
X
R T C
T im e B a s e
In s tr u c tio n
D e c o d e r
fS Y S /4
fS Y S
R T C O u t
P B 2 /T M R 0
U
P F D 0
S T A C K
P ro g ra m
C o u n te r
M
T M R 0 C
T M R 0
In te rru p t
C ir c u it
P B 4 ~ P B 7
B P
O S C 2
O S C 4
O S
R E
V D
V S
O S
S
D
S
P O R T A
A C C
C 1
P A
L C D
M e m o ry
C 3
P A
P A
P A
P A
P A
L C D D r iv e r
H A L T
0 /B Z
1 /B Z
2
3 /P F D
4 ~ P A 7
E N /D IS
L V D /L V R
C O M 0 ~
C O M 2
Rev. 2.00
C O M 3 /
S E G 4 0
S E G 0 ~
S E G 3 9
2
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Pin Assignment
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
O S C
O S C
V D
O S C
O S C
R E
P A 0 /B
P A 1 /B
P A
P A 3 /P F
P A
D
D
S
Z
Z
2
1
4
3
2
4
8
7
6
5
4
3
P B
P B
P B 2
P B 3
1 0 0 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1
5
C
2
1
0
P A
N
N
N
N
N
1
8 0
2
7 9
3
7 8
4
7 7
5
7 6
C
C
C
C
6
7 5
P A 6
P A 7
0 /IN T 0
1 /IN T 1
/T M R 0
/T M R 1
P B 4
P B 5
P B 6
P B 7
P C 0
P C 1
P C 2
P C 3
P C 4
P C 5
P C 6
P C 7
N C
N C
N C
N C
N C
V S S
7
7 4
8
7 3
9
7 2
1 0
7 1
1 1
7 0
1 2
6 9
1 3
6 8
1 4
H T 4 9 R 7 0 A -1 /H T 4 9 C 7 0 -1 /H T 4 9 C 7 0 L
1 0 0 Q F P -A
1 5
1 6
6 7
6 6
6 5
1 7
6 4
1 8
6 3
1 9
6 2
2 0
6 1
2 1
6 0
2 2
5 9
2 3
5 8
2 4
5 7
2 5
5 6
2 6
5 5
2 7
5 4
2 8
5 3
5 2
2 9
3 0
3 1 3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 4 0 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 0
5 1
S E G
S E G
S E G
N C
N C
N C
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
N C
N C
N C
N C
N C
N C
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
N C
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
S E G
C O M
C O M
C O M
C O M
C 2
C 1
V 2
V 1
V L C
D
3 0
3 1
3 2
3 3
3 4
3 5
3 6
3 7
3 8
3 9
3 /S E G 4 0
2
1
0
Rev. 2.00
3
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Pad Description
Pad Name
I/O
Options
Description
I/O
Wake-up
Pull-high
or None
CMOS or
NMOS
PA0~PA7 constitute an 8-bit bidirectional input/output port with Schmitt trigger input capability. Each pin on port can be configured as wake-up input by
options. PA0~PA3 can be configured as CMOS output or NMOS input/output
with or without pull-high resistor by options. PA4~PA7 are always pull-high
NMOS input/output. Of the eight bits, PA0~PA1 can be set as I/O pins or
buzzer outputs by options. PA3 can be set as an I/O pin or as a PFD output
also by options.
I
¾
PB0~PB7 constitute an 8-bit Schmitt trigger input port. Each pin on port are
with pull-high resistor. Of the eight bits, PB0 and PB1 can be set as input pins
or as external interrupt control pins (INT0) and (INT1) respectively, by software application. PB2 and PB3 can be set as an input pin or as a timer/event
counter input pin TMR0 and TMR1 also by software application.
I/O
Pull-high
or None
CMOS or
NMOS
PC0~PC7 constitute an 8-bit bidirectional input/output port with Schmitt trigger input capability. On the port, such can be configured as CMOS output or
NMOS input/output with or without pull-high resistor by options.
V2
I
¾
Voltage pump for HT49R70A-1/HT49C70-1.
LCD power supply for HT49C70L.
VLCD
I
¾
LCD power supply for HT49R70A-1/HT49C70-1.
Voltage pump for HT49C70L.
V1, C1, C2
PA0/BZ
PA1/BZ
PA2
PA3/PFD
PA4~PA7
PB0/INT0
PB1/INT1
PB2/TMR0
PB3/TMR1
PB4~PB7
PC0~PC7
I
¾
COM0~COM2
COM3/SEG40
O
1/2, 1/3 or 1/4
Duty
SEG0~SEG39
O
¾
OSC1
OSC2
I
O
Crystal or RC
OSC1 and OSC2 are connected to an RC network or a crystal (by options) for
the internal system clock. In the case of RC operation, OSC2 is the output terminal for 1/4 system clock.
The system clock may come from the RTC oscillator. If the system clock comes from RTCOSC, these two pins can be floating.
OSC3
OSC4
I
O
RTC or
System Clock
Real time clock oscillators. OSC3 and OSC4 are connected to a 32768Hz
crystal oscillator for timing purposes or to a system clock source (depending
on the options).
No built-in capacitor
VDD
¾
¾
Positive power supply
VSS
¾
¾
Negative power supply, ground
RES
I
¾
Schmitt trigger reset input, active low
Voltage pump
SEG40 can be set as a segment or as a common output driver for LCD panel
by options. COM0~COM2 are outputs for LCD panel plate.
LCD driver outputs for LCD panel segments
Absolute Maximum Ratings
Supply Voltage..........................VSS-0.3V to VSS+6.0V*
Supply Voltage ........................VSS-0.3V to VSS+2.5V**
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
Operating Temperature ...........................-40°C to 85°C
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
²*² For HT49R70A-1/HT49C70-1
²**² For HT49C70L
Rev. 2.00
4
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
D.C. Characteristics
VDD=1.5V for HT49C70L, VDD=3V & VDD=5V for HT49R70A-1 and HT49C70-1
Ta=25°C
Test Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
For HT49C70L
1.2
¾
2.2
V
LVR disable, fSYS=4MHz
(for HT49R70A-1/HT49C70-1)
2.2
¾
5.5
V
fSYS=8MHz
(for HT49R70A-1/HT49C70-1)
3.3
¾
5.5
V
For HT49R70A-1/HT49C70-1,
VA£5.5V
2.2
¾
5.5
V
¾
60
100
mA
¾
1
2
mA
¾
3
5
mA
¾
50
100
mA
¾
1
2
mA
¾
3
5
mA
¾
4
8
mA
¾
2.5
5
mA
¾
0.3
0.6
mA
¾
0.6
1
mA
¾
0.1
0.5
mA
¾
¾
1
mA
¾
¾
2
mA
¾
1
2
mA
¾
2.5
5
mA
¾
10
20
mA
¾
0.5
1
mA
¾
2
5
mA
¾
6
10
mA
¾
17
30
mA
¾
34
60
mA
¾
13
25
mA
¾
26
50
mA
¾
14
25
mA
¾
28
50
mA
¾
10
20
mA
¾
20
40
mA
0
¾
0.3VDD
V
Conditions
VDD
VDD
Operating Voltage
VLCD
LCD Power Supply (Note *)
IDD1
Operating Current
(Crystal OSC)
¾
¾
1.5V No load, fSYS=455kHz
3V
No load, fSYS=4MHz
5V
1.5V No load, fSYS=400kHz
IDD2
Operating Current
(RC OSC)
3V
No load, fSYS=4MHz
5V
IDD3
Operating Current
(Crystal OSC, RC OSC)
IDD4
Operating Current
(fSYS=RTC OSC)
5V
No load, fSYS=8MHz
1.5V
3V
No load
5V
1.5V
ISTB1
Standby Current
(*fS=T1)
3V
No load, system HALT,
LCD Off at HALT
5V
1.5V
ISTB2
Standby Current
(*fS=RTC OSC)
3V
No load, system HALT,
LCD On at HALT, C type
5V
1.5V
ISTB3
Standby Current
(*fS=WDT RC OSC)
3V
No load, system HALT
LCD On at HALT, C type
5V
ISTB4
ISTB5
ISTB6
ISTB7
VIL1
Rev. 2.00
Standby Current
(*fS=RTC OSC)
3V
Standby Current
(*fS=RTC OSC)
3V
Standby Current
(*fS=WDT RC OSC)
3V
Standby Current
(*fS=WDT RC OSC)
3V
5V
No load, system HALT,
LCD On at HALT, R type, 1/3 bias
Input Low Voltage for I/O
Ports, TMR and INT
¾
¾
5V
5V
5V
No load, system HALT,
LCD On at HALT, R type, 1/2 bias
No load, system HALT,
LCD On at HALT, R type, 1/3 bias
No load, system HALT,
LCD On at HALT, R type, 1/2 bias
5
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Test Conditions
Symbol
Parameter
Min.
Typ.
Max.
Unit
For HT49C70L
0.8VDD
¾
VDD
V
For HT49R70A-1/HT49C70-1
0.7VDD
¾
VDD
V
V
Conditions
VDD
VIH1
VIL2
VIH2
Input High Voltage for I/O
Ports, TMR and INT
¾
Input Low Voltage (RES)
¾
¾
0
¾
0.4VDD
Input High Voltage (RES)
¾
¾
0.9VDD
¾
VDD
V
0.4
0.8
¾
mA
6
12
¾
mA
10
25
¾
mA
-0.3
-0.6
¾
mA
-2
-4
¾
mA
-5
-8
¾
mA
210
420
¾
mA
350
700
¾
mA
-80
-160
¾
mA
5V
-180
-360
¾
mA
1.5V
75
150
300
kW
20
60
100
kW
10
30
50
kW
1.5V
IOL1
I/O Port Sink Current
3V
VOL=0.1VDD
5V
1.5V
IOH1
I/O Port Source Current
3V
VOH=0.9VDD
5V
LCD Common and Segment
Current
IOL2
LCD Common and Segment
Current
IOH2
RPH
Pull-high Resistance
3V
VOL=0.1VDD
5V
3V
VOH=0.9VDD
¾
3V
5V
VLVR
Low Voltage Reset Voltage
¾
¾
2.7
3.2
3.6
V
VLVD
Low Voltage Detector Voltage
¾
¾
3.0
3.3
3.6
V
Note:
²*² for the value of VA refer to the LCD driver section.
²*fS² please refer to the WDT clock option
Rev. 2.00
6
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
A.C. Characteristics
VDD=1.5V for HT49C70L, VDD=3V & VDD=5V for HT49R70A-1 and HT49C70-1
Ta=25°C
Test Conditions
Symbol
Parameter
System Clock
(Crystal OSC)
fSYS1
System Clock
(RC OSC)
fSYS2
Min.
Typ.
Max.
Unit
Conditions
VDD
¾
1.2V~2.2V (for HT49C70L)
400
¾
500
kHz
¾
2.2V~5.5V
400
¾
4000
kHz
¾
3.3V~5.5V
400
¾
8000
kHz
¾
1.2V~2.2V (for HT49C70L)
400
¾
500
kHz
¾
2.2V~5.5V
400
¾
4000
kHz
¾
3.3V~5.5V
400
¾
8000
kHz
fSYS3
System Clock
(32768Hz Crystal OSC)
¾
¾
¾
32768
¾
Hz
fRTCOSC
RTC Frequency
¾
¾
¾
32768
¾
Hz
fTIMER
Timer I/P Frequency
¾
1.2V~2.2V (for HT49C70L)
0
¾
500
kHz
¾
2.2V~5.5V
0
¾
4000
kHz
¾
3.3V~5.5V
0
¾
8000
kHz
35
70
140
ms
45
90
180
ms
32
65
130
ms
For HT49C70L
10
¾
¾
ms
For HT49R70A-1/HT49C70-1
1
¾
¾
ms
Wake-up from HALT
¾
1024
¾
*tSYS
0.5
1
2
ms
For HT49C70L
10
¾
¾
ms
For HT49R70A-1/HT49C70-1
1
¾
¾
ms
1.5V
tWDTOSC Watchdog Oscillator Period
¾
3V
5V
tRES
External Reset Low Pulse Width
¾
tSST
System Start-up Timer Period
¾
tLVR
Low Voltage Width to Reset
¾
tINT
Interrupt Pulse Width
¾
Note:
¾
*tSYS= 1/fSYS1, 1/fSYS2 or 1/fSYS3
Rev. 2.00
7
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Functional Description
Execution Flow
After accessing a program memory word to fetch an instruction code, the value of the PC is incremented by 1.
The PC then points to the memory word containing the
next instruction code.
The system clock is derived from either a crystal or an
RC oscillator or a 32768Hz crystal oscillator. It is internally divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles.
When executing a jump instruction, conditional skip execution, loading a PCL register, a subroutine call, an initial reset, an internal interrupt, an external interrupt, or
returning from a subroutine, the PC manipulates the
program transfer by loading the address corresponding
to each instruction.
Instruction fetching and execution are pipelined in such
a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle.
The pipelining scheme makes it possible for each instruction to be effectively executed in a cycle. If an instruction changes the value of the program counter, two
cycles are required to complete the instruction.
The conditional skip is activated by instructions. Once
the condition is met, the next instruction, fetched during
the current instruction execution, is discarded and a
dummy cycle replaces it to get a proper instruction; otherwise proceed to the next instruction.
Program Counter - PC
The program counter (PC) is 13 bits wide and it controls
the sequence in which the instructions stored in the program ROM are executed. The contents of the PC can
specify a maximum of 8192 addresses.
S y s te m
O S C 2 (R C
C lo c k
T 1
T 2
T 3
T 4
The lower byte of the PC (PCL) is a readable and
writeable register (06H). Moving data into the PCL performs a short jump. The destination is within 256 locations.
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
o n ly )
P C
P C
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Mode
Program Counter
*12
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
0
0
External Interrupt 0
0
0
0
0
0
0
0
0
0
0
1
0
0
External Interrupt 1
0
0
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 0 overflow
0
0
0
0
0
0
0
0
0
1
1
0
0
Timer/Event Counter 1 overflow
0
0
0
0
0
0
0
0
1
0
0
0
0
Time Base Interrupt
0
0
0
0
0
0
0
0
1
0
1
0
0
RTC Interrupt
0
0
0
0
0
0
0
0
1
1
0
0
0
Skip
Program Counter + 2
Loading PCL
*12
*11
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#12
#11
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return From Subroutine
S12 S11 S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note:
*12~*0: Program counter bits
#12~#0: Instruction code bits
Rev. 2.00
S12~S0: Stack register bits
@7~@0: PCL bits
8
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
When a control transfer takes place, an additional
dummy cycle is required.
0 0 0 H
D e v ic e in itia liz a tio n p r o g r a m
0 0 4 H
Program Memory - ROM
E x te r n a l in te r r u p t 0 s u b r o u tin e
0 0 8 H
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
8192´16 bits which are addressed by the program
counter and table pointer.
0 0 C H
0 1 0 H
E x te r n a l in te r r u p t 1 s u b r o u tin e
T im e r /e v e n t c o u n te r 0 in te r r u p t s u b r o u tin e
T im e r /e v e n t c o u n te r 1 in te r r u p t s u b r o u tin e
0 1 4 H
T im e B a s e In te r r u p t
0 1 8 H
R T C In te rru p t
Certain locations in the ROM are reserved for special
usage:
· Location 000H
n 0 0 H
Location 000H is reserved for program initialization.
After chip reset, the program always begins execution
at this location.
1 F 0 0 H
L o o k - u p ta b le ( 2 5 6 w o r d s )
1 F F F H
Location 004H is reserved for the external interrupt
service program. If the INT0 input pin is activated, and
the interrupt is enabled, and the stack is not full, the
program begins execution at location 004H.
1 6 b its
N o te : n ra n g e s fro m
0 to 1 F
Program Memory
· Location 008H
· Table location
Location 008H is reserved for the external interrupt
service program also. If the INT1 input pin is activated,
and the interrupt is enabled, and the stack is not full,
the program begins execution at location 008H.
Any location in the ROM can be used as a look-up table. The instructions ²TABRDC [m]² (the current page,
1 page=256 words) and ²TABRDL [m]² (the last page)
transfer the contents of the lower-order byte to the
specified data memory, and the contents of the
higher-order byte to TBLH (Table Higher-order byte
register) (08H). Only the destination of the lower-order
byte in the table is well-defined; the other bits of the table word are all transferred to the lower portion of
TBLH. The TBLH is read only, and the table pointer
(TBLP) is a read/write register (07H), indicating the table location. Before accessing the table, the location
should be placed in TBLP. All the table related instructions require 2 cycles to complete the operation.
These areas may function as a normal ROM depending upon the user¢s requirements.
· Location 00CH
Location 00CH is reserved for the Timer/Event Counter 0 interrupt service program. If a timer interrupt results from a Timer/Event Counter 0 overflow, and if the
interrupt is enabled and the stack is not full, the program begins execution at location 00CH.
· Location 010H
Location 010H is reserved for the Timer/Event Counter 1 interrupt service program. If a timer interrupt results from a Timer/Event Counter 1 overflow, and if the
interrupt is enabled and the stack is not full, the program begins execution at location 010H.
Stack Register - STACK
· Location 014H
Location 014H is reserved for the Time Base interrupt
service program. If a Time Base interrupt occurs, and
the interrupt is enabled, and the stack is not full, the
program begins execution at location 014H.
The stack register is a special part of the memory used
to save the contents of the program counter. The stack
is organized into 16 levels and is neither part of the data
nor part of the program, and is neither readable nor
writeable. Its activated level is indexed by a stack
pointer (SP) and is neither readable nor writeable. At the
start of a subroutine call or an interrupt acknowledgment, the contents of the program counter is pushed
· Location 018H
Location 018H is reserved for the real time clock interrupt service program. If a real time clock interrupt occurs, and the interrupt is enabled, and the stack is not
full, the program begins execution at location 018H.
Instruction(s)
L o o k - u p ta b le ( 2 5 6 w o r d s )
n F F H
· Location 004H
P ro g ra m
R O M
Table Location
*12
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P12
P11
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note:
*12~*0: Table location bits
@7~@0: Table pointer bits
Rev. 2.00
P12~P8: Current program counter bits
9
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
onto the stack. At the end of the subroutine or interrupt
routine, signaled by a return instruction (RET or RETI),
the contents of the program counter is restored to its
previous value from the stack. After chip reset, the SP
will point to the top of the stack.
In d ir e c t A d d r e s s in g R e g is te r 0
0 2 H
M P 0
In d ir e c t A d d r e s s in g R e g is te r 1
0 3 H
M P 1
0 4 H
B P
A C C
P C L
0 5 H
If the stack is full and a non-masked interrupt takes
place, the interrupt request flag is recorded but the acknowledgment is still inhibited. Once the SP is decremented (by RET or RETI), the interrupt is serviced. This
feature prevents stack overflow, allowing the programmer to use the structure easily. Likewise, if the stack is
full, and a ²CALL² is subsequently executed, a stack
overflow occurs and the first entry is lost (only the most
recent 16 return addresses are stored).
0 6 H
0 7 H
0 8 H
T B L P
T B L H
0 9 H
R T C C
0 A H
S T A T U S
0 B H
IN T C 0
0 C H
0 D H
0 E H
0 F H
Data Memory - RAM
T M R 0
T M R 0 C
T M R 1 H
1 1 H
T M R 1 L
T M R 1 C
1 2 H
P A
1 0 H
The data memory (RAM) is designed with 245´8 bits,
and is divided into two functional groups, namely; special function registers and general purpose data memory, most of which are readable/writeable, although
some are read only.
S p e c ia l P u r p o s e
D a ta M e m o ry
1 3 H
1 4 H
P B
1 5 H
1 6 H
Of the two types of functional groups, the special function
registers consist of an Indirect addressing register 0
(00H), a Memory pointer register 0 (MP0;01H), an Indirect addressing register 1 (02H), a Memory pointer register 1 (MP1;03H), a Bank pointer (BP;04H), an
Accumulator (ACC;05H), a Program counter lower-order
byte register (PCL;06H), a Table pointer (TBLP;07H), a
Table higher-order byte register (TBLH;08H), a Real time
clock control register (RTCC;09H), a Status register
(STATUS;0AH), an Interrupt control register 0
(INTC0;0BH), a Timer/Event Counter 0 (TMR0;0DH), a
Timer/Event Counter 0 control register (TMR0C;0EH), a
Timer/Event Counter 1 (TMR1H:0FH;TMR1L;10H), a
Timer/Event Counter 1 control register (TMR1C;11H), I/O
registers (PA;12H, PB;14H, PC;16H), and Interrupt control register 1 (INTC1;1EH). On the other hand, the general purpose data memory, addressed from 20H to FFH,
is used for data and control information under instruction
commands.
P C
1 7 H
1 8 H
1 9 H
1 A H
1 B H
1 C H
1 D H
1 E H
1 F H
2 0 H
IN T C 1
G e n e ra l P u rp o s e
D a ta M e m ro y
(2 2 4 B y te s )
F F H
: U n u s e d .
R e a d a s "0 "
RAM Mapping
The function of data movement between two indirect addressing registers is not supported. The memory pointer
registers, MP0 and MP1, are both 8-bit registers used to
access the RAM by combining corresponding indirect
addressing registers. MP0 can only be applied to data
memory, while MP1 can be applied to data memory and
LCD display memory.
The areas in the RAM can directly handle arithmetic,
logic, increment, decrement, and rotate operations. Except some dedicated bits, Each pin in the RAM can be
set and reset by ²SET [m].i² and ²CLR [m].i² They are
also indirectly accessible through the Memory pointer
register 0 (MP0;01H) or the Memory pointer register 1
(MP1;03H).
Accumulator - ACC
The accumulator (ACC) is related to the ALU operations. It is also mapped to location 05H of the RAM and
is capable of operating with immediate data. The data
movement between two data memory locations must
pass through the ACC.
Indirect Addressing Register
Location 00H and 02H are indirect addressing registers
that are not physically implemented. Any read/write operation of [00H] and [02H] accesses the RAM pointed to
by MP0 (01H) and MP1(03H) respectively. Reading location 00H or 02H indirectly returns the result 00H.
While, writing it indirectly leads to no operation.
Rev. 2.00
0 0 H
0 1 H
10
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Arithmetic and Logic Unit - ALU
Interrupts
This circuit performs 8-bit arithmetic and logic operations and provides the following functions:
The device provides two external interrupts, two internal
timer/event counter interrupts, an internal time base interrupt, and an internal real time clock interrupt. The interrupt control register 0 (INTC0;0BH) and interrupt
control register 1 (INTC1;1EH) both contain the interrupt
control bits that are used to set the enable/disable status
and interrupt request flags.
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Logic operations (AND, OR, XOR, CPL)
· Rotation (RL, RR, RLC, RRC)
· Increment and Decrement (INC, DEC)
· Branch decision (SZ, SNZ, SIZ, SDZ etc.)
Once an interrupt subroutine is serviced, other interrupts are all blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
interrupt requests may take place during this interval,
but only the interrupt request flag will be recorded. If a
certain interrupt requires servicing within the service
routine, the EMI bit and the corresponding bit of the
INTC0 or of INTC1 may be set in order to allow interrupt
nesting. Once the stack is full, the interrupt request will
not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If immediate service
is desired, the stack should be prevented from becoming full.
The ALU not only saves the results of a data operation
but also changes the status register.
Status Register - STATUS
The status register (0AH) is 8 bits wide and contains, a
carry flag (C), an auxiliary carry flag (AC), a zero flag (Z),
an overflow flag (OV), a power down flag (PDF), and a
watchdog time-out flag (TO). It also records the status
information and controls the operation sequence.
Except for the TO and PDF flags, bits in the status register can be altered by instructions similar to other registers. Data written into the status register does not alter
the TO or PDF flags. Operations related to the status
register, however, may yield different results from those
intended. The TO and PDF flags can only be changed
by a Watchdog Timer overflow, chip power-up, or clearing the Watchdog Timer and executing the ²HALT² instruction. The Z, OV, AC, and C flags reflect the status of
the latest operations.
All these interrupts can support a wake-up function. As an
interrupt is serviced, a control transfer occurs by pushing
the contents of the program counter onto the stack followed by a branch to a subroutine at the specified location
in the ROM. Only the contents of the program counter is
pushed onto the stack. If the contents of the register or of
the status register (STATUS) is altered by the interrupt service program which corrupts the desired control sequence,
the contents should be saved in advance.
On entering the interrupt sequence or executing the
subroutine call, the status register will not be automatically pushed onto the stack. If the contents of the status
is important, and if the subroutine is likely to corrupt the
status register, the programmer should take precautions
and save it properly.
Bit No.
External interrupts are triggered by a high to low transition of INT0 or INT1, and the related interrupt request
flag (EIF0; bit 4 of INTC0, EIF1; bit 5 of INTC0) is set as
well. After the interrupt is enabled, the stack is not full,
and the external interrupt is active, a subroutine call to
location 04H or 08H occurs. The interrupt request flag
(EIF0 or EIF1) and EMI bits are all cleared to disable
other interrupts.
Label
Function
0
C
C is set if an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate through carry instruction.
1
AC
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from
the high nibble into the low nibble in subtraction; otherwise AC is cleared.
2
Z
3
OV
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa; otherwise OV is cleared.
4
PDF
PDF is cleared by either a system power-up or executing the ²CLR WDT² instruction. PDF is
set by executing the ²HALT² instruction.
5
TO
TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction. TO
is set by a WDT time-out.
6, 7
¾
Unused bit, read as ²0²
Z is set if the result of an arithmetic or logic operation is zero; otherwise Z is cleared.
Status (0AH) Register
Rev. 2.00
11
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
terrupt control bit are set both to 1 (if the stack is not full).
To return from the interrupt subroutine, ²RET² or ²RETI²
may be invoked. RETI sets the EMI bit and enables an
interrupt service, but RET does not.
The internal Timer/Event Counter 0 interrupt is initialized by setting the Timer/Event Counter 0 interrupt request flag (T0F;bit 6 of INTC0), which is normally
caused by a timer overflow. After the interrupt is enabled, and the stack is not full, and the T0F bit is set, a
subroutine call to location 0CH occurs. The related interrupt request flag (T0F) is reset, and the EMI bit is
cleared to disable further interrupts. The Timer/Event
Counter 1 is operated in the same manner but its related
interrupt request flag is T1F (bit 4 of INTC1) and its subroutine call location is 10H.
Interrupts occurring in the interval between the rising
edges of two consecutive T2 pulses are serviced on the
latter of the two T2 pulses if the corresponding interrupts
are enabled. In the case of simultaneous requests, the
priorities in the following table apply. These can be
masked by resetting the EMI bit.
Interrupt Source
The time base interrupt is initialized by setting the time
base interrupt request flag (TBF;bit 5 of INTC1), that is
caused by a regular time base signal. After the interrupt
is enabled, and the stack is not full, and the TBF bit is
set, a subroutine call to location 14H occurs. The related
interrupt request flag (TBF) is reset and the EMI bit is
cleared to disable further interrupts.
The real time clock interrupt is initialized by setting the
real time clock interrupt request flag (RTF; bit 6 of
INTC1), that is caused by a regular real time clock signal. After the interrupt is enabled, and the stack is not
full, and the RTF bit is set, a subroutine call to location
18H occurs. The related interrupt request flag (RTF) is
reset and the EMI bit is cleared to disable further interrupts.
Vector
External interrupt 0
1
04H
External interrupt 1
2
08H
Timer/Event Counter 0 overflow
3
0CH
Timer/Event Counter 1 overflow
4
10H
Time base interrupt
5
14H
Real time clock interrupt
6
18H
The Timer/Event Counter 0 interrupt request flag, T0F,
external interrupt 1 request flag (EIF1), external interrupt 0 request flag (EIF0), enable Timer/Event Counter
0 interrupt bit (ET0I), enable external interrupt 1 bit
(EEI1), enable external interrupt 0 bit (EEI0), and enable master interrupt bit (EMI) make up of the Interrupt
Control register 0 (INTC0) which is located at 0BH in the
RAM. The real time clock interrupt request flag (RTF),
time base interrupt request flag (TBF), Timer/Event
Counter 1 interrupt request flag (T1F), enable real time
During the execution of an interrupt subroutine, other interrupt acknowledgments are all held until the ²RETI²
instruction is executed or the EMI bit and the related inBit No.
Priority
Label
Function
0
EMI
Controls the master (global) interrupt (1=enabled; 0=disabled)
1
EEI0
Controls the external interrupt 0 (1=enabled; 0=disabled)
2
EEI1
Controls the external interrupt 1 (1=enabled; 0=disabled)
3
ET0I
Controls the Timer/Event Counter 0 interrupt (1=enabled; 0=disabled)
4
EIF0
External interrupt 0 request flag (1=active; 0=inactive)
5
EIF1
External interrupt 1 request flag (1=active; 0=inactive)
6
T0F
Internal Timer/Event Counter 0 request flag (1=active; 0=inactive)
7
¾
Unused bit, read as ²0²
INTC0 (0BH) Register
Bit No.
Label
Function
0
ET1I
Controls the Timer/Event Counter 1 interrupt (1=enabled; 0=disabled)
1
ETBI
Controls the time base interrupt (1=enabled; 0:disabled)
2
ERTI
Controls the real time clock interrupt (1=enabled; 0:disabled)
3
¾
4
T1F
Unused bit, read as ²0²
Internal Timer/Event Counter 1 request flag (1=active; 0=inactive)
5
TBF
Time base request flag (1=active; 0=inactive)
6
RTF
Real time clock request flag (1=active; 0=inactive)
7
¾
Unused bit, read as ²0²
INTC1 (1EH) Register
Rev. 2.00
12
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
clock interrupt bit (ERTI), and enable time base interrupt
bit (ETBI), enable Timer/Event Counter 1 interrupt bit
(ET1I) on the other hand, constitute the Interrupt Control
register 1 (INTC1) which is located at 1EH in the RAM.
EMI, EEI0, EEI1, ET0I, ET1I, ETBI, and ERTI are all
used to control the enable/disable status of interrupts.
These bits prevent the requested interrupt from being
serviced. Once the interrupt request flags (RTF, TBF,
T0F, T1F, EIF1, EIF0) are all set, they remain in the
INTC1 or INTC0 respectively until the interrupts are serviced or cleared by a software instruction.
ature, and the chip itself due to process variations. It is
therefore, not suitable for timing sensitive operations
where accurate oscillator frequency is desired.
It is recommended that a program should not use the
²CALL subroutine² within the interrupt subroutine. It¢s because interrupts often occur in an unpredictable manner
or require to be serviced immediately in some applications. During that period, if only one stack is left, and enabling the interrupt is not well controlled, operation of the
²call² in the interrupt subroutine may damage the original control sequence.
There is another oscillator circuit designed for the real
time clock. In this case, only the 32.768kHz crystal oscillator can be applied. The crystal should be connected
between OSC3 and OSC4.
Oscillator Configuration
The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Although
the system enters the power down mode, the system
clock stops, and the WDT oscillator still works with a period of approximately 65ms at 5V. The WDT oscillator
can be disabled by options to conserve power.
On the other hand, if the crystal oscillator is selected, a
crystal across OSC1 and OSC2 is needed to provide the
feedback and phase shift required for the oscillator, and
no other external components are required. A resonator
may be connected between OSC1 and OSC2 to replace
the crystal and to get a frequency reference, but two external capacitors in OSC1 and OSC2 are required.
The RTC oscillator circuit can be controlled to oscillate
quickly by setting the ²QOSC² bit (bit 4 of RTCC). It is
recommended to turn on the quick oscillating function
upon power on, and then turn it off after 2 seconds.
These devices provide three oscillator circuits for system clocks, i.e., RC oscillator, crystal oscillator and
32768Hz crystal oscillator, determined by options. No
matter what type of oscillator is selected, the signal is
used for the system clock. The HALT mode stops the
system oscillator (RC and crystal oscillator only) and ignores external signal in order to conserve power. The
32768Hz crystal oscillator (system oscillator) still runs at
HALT mode. If the 32768Hz crystal oscillator is selected
as the system oscillator, the system oscillator is not
stopped; but the instruction execution is stopped. Since
the system oscillator or oscillator) is also designed for
timing purposes, the internal timing (RTC, time base,
WDT) operation still runs even if the system enters the
HALT mode.
Watchdog Timer - WDT
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator) or an instruction clock
(system clock/4) or a real time clock oscillator (RTC oscillator). The timer is designed to prevent a software
malfunction or sequence from jumping to an unknown
location with unpredictable results. The WDT can be
disabled by options. But if the WDT is disabled, all executions related to the WDT lead to no operation.
The WDT time-out period is fS/215~fS/216.
Of the three oscillators, if the RC oscillator is used, an
external resistor between OSC1 and VSS is required,
and the range of the resistance should be from 24kW to
1MW for HT49R70A-1/HT49C70-1 and from 560kW to
1MW for HT49C70L. The system clock, divided by 4, is
available on OSC2 with pull-high resistor, which can be
used to synchronize external logic. The RC oscillator
provides the most cost effective solution. However, the
frequency of the oscillation may vary with VDD, temper-
If the WDT clock source chooses the internal WDT oscillator, the time-out period may vary with temperature,
VDD, and process variations. On the other hand, if the
clock source selects the instruction clock and the
²HALT² instruction is executed, WDT may stop counting
and lose its protecting purpose, and the logic can only
be restarted by an external logic.
V
O S C 3
O S C 4
3 2 7 6 8 H z C r y s ta l/
R T C O s c illa to r
D D
4 7 0 p F
O S C 1
V
O S C 2
C r y s ta l O s c illa to r
fS
Y S
/4
O S C 1
D D
O S C 2
R C
O s c illa to r
System Oscillator
Rev. 2.00
13
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
S y s te m
C lo c k /4
R T C
O S C 3 2 7 6 8 H z
fS
O p tio n
S e le c t
D iv id e r
D iv id e r
C K
W D T
1 2 k H z
O S C
T
R
C K
T
R
T im e - o u t R e s e t fS /2
1 5
~ fS /2
1 6
W D T C le a r
Watchdog Timer
from the WDT OSC or RTC OSC or the instruction clock
(i.e., system clock divided by 4). The multi-function timer
also provides a selectable frequency signal (ranges
from fS/22 to fS/28) for LCD driver circuits, and a
selectable frequency signal (ranging from fS/22 to fS/29)
for the buzzer output by options. It is recommended to
select a nearly 4kHz signal for the LCD driver circuits to
have proper display.
When the device operates in a noisy environment, using
the on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT can stop the system clock.
The WDT overflow under normal operation initializes a
²chip reset² and sets the status bit ²TO². In the HALT
mode, the overflow initializes a ²warm reset², and only
the program counter and SP are reset to zero. To clear
the contents of the WDT, there are three methods to be
adopted, i.e., external reset (a low level to RES), software instruction, and a ²HALT² instruction. There are
two types of software instructions; ²CLR WDT² and the
other set - ²CLR WDT1² and ²CLR WDT2². Of these
two types of instruction, only one type of instruction can
be active at a time depending on the options - ²CLR
WDT² times selection option. If the ²CLR WDT² is selected (i.e., CLR WDT times equal one), any execution
of the ²CLR WDT² instruction clears the WDT. In the
case that ²CLR WDT1² and ²CLR WDT2² are chosen
(i.e., CLR WDT times equal two), these two instructions
have to be executed to clear the WDT; otherwise, the
WDT may reset the chip due to time-out.
Time Base
The time base offers a periodic time-out period to generate a regular internal interrupt. Its time-out period
ranges from fS/212 to fS/215 selected by options. If time
base time-out occurs, the related interrupt request flag
(TBF; bit 5 of INTC1) is set. But if the interrupt is enabled, and the stack is not full, a subroutine call to location 14H occurs. The time base time-out signal can also
be applied as a clock source of the Timer/Event Counter
1 so as to get a longer time-out period.
Real Time Clock - RTC
The real time clock (RTC) is operated in the same manner as the time base that is used to supply a regular internal interrupt. Its time-out period ranges from fS/28 to
fS/215 by software programming . Writing data to RT2,
RT1 and RT0 (bit 2, 1, 0 of RTCC;09H) yields various
time-out periods. If the RTC time-out occurs, the related
interrupt request flag (RTF; bit 6 of INTC1) is set. But if
Multi-function Timer
These devices provide a multi-function timer for the
WDT , time base and RTC but with different time-out periods. The multi-function timer consists of an 8-stage divider and a 7-bit prescaler, with the clock source coming
fs
D iv id e r
P r e s c a le r
O p tio n
O p tio n
L C D D r iv e r ( fS /2 2 ~ fS /2 8 )
B u z z e r (fS /2 2~ fS /2 9)
T im e B a s e In te r r u p t
fS /2 12~ fS /2 15
Time Base
fS
D iv id e r
P r e s c a le r
R T 2
R T 1
R T 0
8 to 1
M u x .
fS /2 8~ fS /2 15
R T C In te rru p t
Real Time Clock
Rev. 2.00
14
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
terrupt is enabled, and the stack is not full, the regular interrupt response takes place.
the interrupt is enabled, and the stack is not full, a subroutine call to location 18H occurs. The real time clock
time-out signal also can be applied as a clock source of
the Timer/Event Counter 0 in order to get a longer
time-out period.
RT2
RT1
RT0
RTC Clock Divided Factor
0
0
0
2 8*
0
0
1
2 9*
0
1
0
210*
0
1
1
211*
1
0
0
212
1
0
1
213
1
1
0
214
1
15
1
1
2
When an interrupt request flag is set before entering the
²HALT² status, the system cannot be awakened using
that interrupt.
If wake-up events occur, it takes 1024 tSYS (system
clock period) to resume normal operation. In other
words, a dummy period is inserted after the wake-up. If
the wake-up results from an interrupt acknowledgment,
the actual interrupt subroutine execution is delayed by
more than one cycle. However, if the Wake-up results in
the next instruction execution, the execution will be performed immediately after the dummy period is finished.
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
Reset
Note: ²*² not recommended to be used
There are three ways in which reset may occur.
Power Down Operation - HALT
· RES is reset during normal operation
The HALT mode is initialized by the ²HALT² instruction
and results in the following.
· RES is reset during HALT
· WDT time-out is reset during normal operation
· The system oscillator turns off but the WDT or RTC
The WDT time-out during HALT differs from other chip
reset conditions, for it can perform a ²warm reset² that
resets only the program counter and SP and leaves the
other circuits at their original state. Some registers remain unaffected during any other reset conditions. Most
registers are reset to the ²initial condition² once the reset conditions are met. Examining the PDF and TO
flags, the program can distinguish between different
²chip resets².
oscillator keeps running (if the WDT oscillator or the
real time clock is selected).
· The contents of the on-chip RAM and of the registers
remain unchanged.
· The WDT is cleared and start recounting (if the WDT
clock source is from the WDT oscillator or the real time
clock oscillator).
· All I/O ports maintain their original status.
· The PDF flag is set but the TO flag is cleared.
· LCD driver is still running (if the WDT OSC or RTC
OSC is selected).
The system quits the HALT mode by an external reset,
an interrupt, an external falling edge signal on port A, or
a WDT overflow. An external reset causes device initialization, and the WDT overflow performs a ²warm reset².
After examining the TO and PDF flags, the reason for
chip reset can be determined. The PDF flag is cleared by
system power-up or by executing the ²CLR WDT² instruction, and is set by executing the ²HALT² instruction.
On the other hand, the TO flag is set if WDT time-out occurs, and causes a wake-up that only resets the PC (Program Counter) and SP, and leaves the others at their
original state.
PDF
RESET Conditions
0
0
RES reset during power-up
u
u
RES reset during normal operation
0
1
RES Wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT Wake-up HALT
Note: ²u² stands for unchanged
V
D D
0 .0 1 m F *
1 0 0 k W
R E S
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each pin
in port A can be independently selected to wake up the
device by options. Awakening from an I/O port stimulus,
the program resumes execution of the next instruction.
On the other hand, awakening from an interrupt, two sequence may occur. If the related interrupt is disabled or
the interrupt is enabled but the stack is full, the program
resumes execution at the next instruction. But if the inRev. 2.00
TO
1 0 k W
0 .1 m F *
Reset Circuit
Note:
15
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to
avoid noise interference.
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
An extra option load time delay is added during reset
and power on.
V D D
R E S
tS
S T
The functional unit chip reset status is shown below.
S S T T im e - o u t
C h ip
R e s e t
Reset Timing Chart
H A L T
W D T
W a rm
W D T
R e s e t
T im e - o u t
R e s e t
E x te rn a l
R E S
000H
Interrupt
Disabled
Prescaler, Divider
Cleared
WDT, RTC,
Time Base
Cleared. After master reset,
WDT starts counting
Timer/event Counter
Off
Input/output Ports
Input mode
Stack Pointer
Points to the top of the stack
C o ld
R e s e t
S S T
1 0 - b it R ip p le
C o u n te r
O S C 1
Program Counter
Timer/Event Counter
Two timer/event counters are implemented in the device. One of them contains an 8-bit programmable
count-up counter, the other contains a 16-bit programmable count-up counter.
P o w e r - o n D e te c tio n
Reset Configuration
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses when the system awakes from a HALT state. Awaking from a HALT
state, an SST delay is added.
The Timer/Event Counter 0 clock source may come
from the system clock or system clock/4 or RTC time-out
signal or external source. System clock source or system clock/4 is selected by options.
The register states are summarized below:
Register
TMR0
Reset (Power On)
xxxx xxxx
WDT Time-out
RES Reset
(Norma Operation) (Normal Operation)
xxxx xxxx
xxxx xxxx
RES Reset
(HALT)
WDT Time-out
(HALT)*
xxxx xxxx
uuuu uuuu
TMR0C
0000 1---
0000 1---
0000 1---
0000 1---
uuuu u---
TMR1H
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1L
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1C
0000 1---
0000 1---
0000 1---
0000 1---
uuuu u---
Program Counter
0000H
0000H
0000H
0000H
0000H
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
BP
---- ---0
---- ---0
---- ---0
---- ---0
---- ---u
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLP
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
INTC0
-000 0000
-000 0000
-000 0000
-000 0000
-uuu uuuu
INTC1
-000 -000
-000 -000
-000 -000
-000 -000
-uuu -uuu
RTCC
--00 0111
--00 0111
--00 0111
--00 0111
--uu uuuu
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
PC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
Note:
²*² stands for warm reset
²u² stands for unchanged
²x² stands for unknown
Rev. 2.00
16
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
lower-order byte buffer to TMR1H and TMR1L registers,
respectively. The Timer/Event Counter 1 preload register is changed by each writing TRM1H operations.
Reading TMR1H will latch the contents of TMR1H and
TMR1L counters to the destination and the lower-order
byte buffer, respectively. Reading the TMR1L will read
the contents of the lower-order byte buffer. The TMR1C
is the Timer/Event Counter 1 control register, which defines the operating mode, counting enable or disable
and an active edge.
The Timer/Event Counter 1 clock source may come
from TMR0 overflow or system clock or time base
time-out signal or system clock/4 or external source,
and the three former clock source is selected by options.
Using external clock input allows the user to count external events, measure time internals or pulse widths, or
generate an accurate time base. While using the internal clock allows the user to generate an accurate time
base.
There are two registers related to the Timer/Event
Counter 0; TMR0 ([0DH]), TMR0C ([0EH]). Two physical registers are mapped to TMR0 location; writing
TMR0 puts the starting value in the Timer/Event Counter 0 register and reading TMR0 takes the contents of
the Timer/Event Counter 0. The TMR0C is a timer/event
counter control register, which defines some options.
The T0M0 and T0M1 (T1M0 and T1M1) bits define the
operation mode. The event count mode is used to count
external events, which means that the clock source is
from an external (TMR0, TMR1) pin. The timer mode
functions as a normal timer with the clock source coming from the internal selected clock source. Finally, the
pulse width measurement mode can be used to count
the high or low level duration of the external signal
(TMR0, TMR1), and the counting is based on the internal selected clock source.
There are three registers related to the Timer/Event
Counter 1; TMR1H (0FH), TMR1L (10H), TMR1C (11H).
Writing TMR1L will only put the written data to an internal lower-order byte buffer (8-bit) and writing TMR1H
will transfer the specified data and the contents of the
S y s te m
S y s te m
C lo c k
M
O p tio n
C lo c k /4
f IN
U
In the event count or timer mode, the timer/event counter starts counting at the current contents in the
T
X
D a ta B u s
R T C O u t
T 0 M 1
T 0 M 0
T 0 S
T M R 0
T im e r /E v e n t C o u n te r 0
P r e lo a d R e g is te r
R e lo a d
T 0 E
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
T 0 M 1
T 0 M 0
T 0 O N
T im e r /E v e n t
C c o u n te r 0
O v e r flo w
to In te rru p t
P F D 0
Timer/Event Counter 0
T M R 0 O v e r flo w
S y s te m
C lo c k
O p tio n
S e le c t
D a ta B u s
U
X
T im e B a s e O u t
S y s te m
M
L o w B y te
B u ffe r
C lo c k /4
T 1 M 1
T 1 M 0
T 1 S
T M R 1
1 6 - B it
P r e lo a d R e g is te r
T 1 E
T 1 M 1
T 1 M 0
T 1 O N
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
H ig h B y te
R e lo a d
O v e r flo w
L o w B y te
to In te rru p t
1 6 - B it T im e r /E v e n t C o u n te r
P F D 1
Timer/Event Counter 1
P F D 0
P F D 1
M
U
X
1 /2
P F D
P A 3 D a ta C T R L
P F D
S o u r c e O p tio n
PFD Source Option
Rev. 2.00
17
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
timer/event counter and ends at FFH (FFFFH). Once an
overflow occurs, the counter is reloaded from the
timer/event counter preload register, and generates an
interrupt request flag (T0F: bit 6 of INTC0; T1F: bit 4 of
INTC1).
the timer/event counter begins counting not according
to the logic level but to the transient edges. In the case of
counter overflows, the counter is reloaded from the
timer/event counter register and issues an interrupt request, as in the other two modes, i.e., event and timer
modes.
In the pulse width measurement mode with the values of
the T0ON/T1ON and T0E/T1E bits equal to 1, after the
TMR0 (TMR1) has received a transient from low to high
(or high to low if the T0E/T1E bit is ²0²), it will start
counting until the TMR0 (TMR1) returns to the original
level and resets the T0ON/T1ON. The measured result
remains in the timer/event counter even if the activated
transient occurs again. In other words, only 1-cycle
measurement can be made until the T0ON/T1ON is set.
The cycle measurement will re-function as long as it receives further transient pulse. In this operation mode,
Bit No.
Label
0~2
¾
3
T0E
4
T0ON
5
T0S
6
7
T0M0
T0M1
To enable the counting operation, the Timer ON bit
(T0ON: bit 4 of TMR0C; T1ON: bit 4 of TMR1C) should
be set to 1. In the pulse width measurement mode, the
T0ON/T1ON is automatically cleared after the measurement cycle is completed. But in the other two modes, the
T0ON/T1ON can only be reset by instructions. The
overflow of the Timer/Event Counter 0/1 is one of the
wake-up sources and can also be applied to a PFD (Programmable Frequency Divider) output at PA3 by options. Only one PFD (PFD0 or PFD1) can be applied to
Function
Unused bit, read as ²0²
Defines the TMR0 active edge of the timer/event counter:
In Event Counter Mode (T0M1,T0M0)=(0,1):
1:count on falling edge;
0:count on rising edge
In Pulse Width measurement mode (T0M1,T0M0)=(1,1):
1: start counting on the rising edge, stop on the falling edge;
0: start counting on the falling edge, stop on the rising edge
Enable/disable timer counting
(0=disabled; 1=enabled)
2 to 1 multiplexer control inputs which selects the timer/event counter clock source (0=RTC
outputs; 1= system clock or system clock/4)
Defines the operating mode (T0M1, T0M0)
01= Event count mode (External clock)
10= Timer mode (Internal clock)
11= Pulse Width measurement mode (External clock)
00= Unused
TMR0C (0EH) Register
Bit No.
Label
0~2
¾
3
T1E
4
T1ON
5
T1S
6
7
T1M0
T1M1
Function
Unused bit, read as ²0²
Defines the TMR1 active edge of the timer/event counter:
In Event Counter Mode (T1M1,T1M0)=(0,1):
1:count on falling edge;
0:count on rising edge
In Pulse Width measurement mode (T1M1,T1M0)=(1,1):
1: start counting on the rising edge, stop on the falling edge;
0: start counting on the falling edge, stop on the rising edge
Enable/disable timer counting
(0= disabled; 1= enabled)
2 to 1 multiplexer control inputs to select the timer/event counter clock source
(0= option clock source; 1= system clock/4)
Defines the operating mode (T1M1, T1M0)
01= Event count mode (External clock)
10= Timer mode (Internal clock)
11= Pulse Width measurement mode (External clock)
00= Unused
TMR1C (11H) Register
Rev. 2.00
18
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
set tmr0c.4
set tmr1c.4
PA3 by options. If PA3 is set as PFD output, there are
two types of selections; One is PFD0 as the PFD output,
the other is PFD1 as the PFD output. PFD0, PFD1 are
the timer overflow signals of the Timer/Event Counter 0,
Timer/Event Counter 1 respectively. No matter what the
operation mode is, writing a 0 to ET0I or ET1I disables
the related interrupt service. When the PFD function is
selected, executing ²CLR [PA].3² instruction to enable
PFD output and executing ²SET [PA].3² instruction to
disable PFD output.
END
Input/Output Ports
There are two 8-bit bidirectional input/output ports, PA
and PC and one 8-bit input port PB. PA, PB and PC are
mapped to [12H], [14H] and [16H] of the RAM, respectively. PA0~PA3 can be configured as CMOS (output) or
NMOS (input/output) with or without pull-high resistor by
options. PA4~PA7 are always pull-high and NMOS (input/output). If NMOS (input) is chosen, Each pin on the
port (PA0~PA7) can be configured as a wake-up input.
PB can only be used for input operation. PC can be configured as CMOS output or NMOS input/output with or
without pull-high resistor by options. All the ports for the
input operation (PA, PB and PC), are non-latched, that
is, the inputs should be ready at the T2 rising edge of the
instruction ²MOV A, [m]² (m=12H, 14H or 16H). For PA,
PC output operation, all data are latched and remain unchanged until the output latch is rewritten.
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register also reloads that data to the timer/event counter. But if the
timer/event counter is turn on, data written to the
timer/event counter is kept only in the timer/event counter preload register. The timer/event counter still continues its operation until an overflow occurs.
When the timer/event counter (reading TMR0/TMR1) is
read, the clock is blocked to avoid errors, as this may results in a counting error. Blocking of the clock should be
taken into account by the programmer.
When the PA and PC structures are open drain NMOS
type, it should be noted that, before reading data from
the pads, a ²1² should be written to the related bits to
disable the NMOS device. That is, executing first the instruction ²SET [m].i² (i=0~7 for PA) to disable related
NMOS device, and then ²MOV A, [m]² to get stable data.
It is strongly recommended to load a desired value into
the TMR0/TMR1 register first, before turning on the related timer/event counter, for proper operation since the
initial value of TMR0/TMR1 is unknown.
Due to the timer/event scheme, the programmer should
pay special attention on the instruction to enable then
disable the timer for the first time, whenever there is a
need to use the timer/event function, to avoid unpredictable result. After this procedure, the timer/event function
can be operated normally. An example is given, using
one 8-bit and one 16-bit width Timer (timer 0; timer 1)
cascaded into 24-bit width.
After chip reset, these input lines remain at the high level
or are left floating (by options). Each pin of these output
latches can be set or cleared by the ²MOV [m], A²
(m=12H or 16H) instruction.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or to the accumulator. When a PA or PC line is
used as an I/O line, the related PA or PC line options
should be configured as NMOS with or without pull-high
resistor. Once a PA or PC line is selected as a CMOS
output, the I/O function cannot be used.
START:
mov
mov
a, 09h ; Set ET0I & EMI bits to
intc0, a ; enable timer 0 and
; global interrupt
mov a, 01h ; Set ET1I bit to enable
mov intc1, a ; timer 1 interrupt
mov a, 80h ; Set operating mode as
mov tmr1c, a ; timer mode and select mask
; option clock source
The input state of a PA or PC line is read from the related
PA or PC pad. When the PA or PC is configured as
NMOS with or without pull-high resistor, one should be
careful when applying a read-modify-write instruction to
PA or PC. Since the read-modify-write will read the entire port state (pads state) first, execute the specified instruction and then write the result to the port data
register. When the read operation is executed, a fault
pad state (caused by the load effect or floating state)
may be read. Errors will then occur.
mov a, 0a0h ; Set operating mode as timer
mov tmr0c, a ; mode and select system
; clock/4
set
clr
tmr1c.4 ; Enable then disable timer 1
tmr1c.4 ; for the first time
mov
mov
mov
mov
mov
a, 00h
tmr0, a
a, 00h
tmr1l, a
tmr1h, a
Rev. 2.00
; Normal operating
;
; Load a desired value into
; the TMR0/TMR1 register
;
;
;
There are three function pins that share with the PA port:
PA0/BZ, PA1/BZ and PA3/PFD.
19
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
V
V
D
D a ta B u s
Q
C K
W r ite
C /N
O
(P
P
D D
D D
W e a k
P u ll- u p
M O S
p tio n
A 0 ~ P A 3 ,
C )
O p tio n
(P A 0 ~ P A 3 , P C )
Q
S
V
P A 0 ~ P A 7
P C 0 ~ P C 7
D D
W e a k
P u ll- u p
C h ip R e s e t
D a ta b u s
P B 0 ~ P B 7
R e a d I/O
R e a
S y
W a k
(P A
d I/O
s te m
e -u p
o n ly )
O p tio n
PA, PC Input/Output Ports
PB input Port
LCD Display Memory
The BZ and BZ are buzzer driving output pair and the
PFD is a programmable frequency divider output. If the
user wants to use the BZ/BZ or PFD function, the related
PA port should be set as a CMOS output. The buzzer
output signals are controlled by PA0 and PA1 data registers as defined in the following table.
PA1 Data
Register
PA0 Data
Register
0
0
PA0=BZ, PA1=BZ
1
0
PA0=BZ, PA1=0
X
1
PA0=0, PA1=0
The device provides an area of embedded data memory
for LCD display. This area is located from 40H to 68H of
the RAM at Bank 1. Bank pointer (BP; located at 04H of
the RAM) is the switch between the RAM and the LCD
display memory. When the BP is set as ²01H², any data
written into 40H~68H will affect the LCD display. When
the BP is cleared to ²00H², any data written into
40H~68H is meant to access the general purpose data
memory. The LCD display memory can be read and written to only by indirect addressing mode using MP1.
PA0/PA1 Pad State
When data is written into the display data area, it is automatically read by the LCD driver which then generates
the corresponding LCD driving signals. To turn the display on or off, a ²1² or a ²0² is written to the corresponding bit of the display memory, respectively. The figure
illustrates the mapping between the display memory
and LCD pattern for the device.
Note: ²X² stands for unused
The PFD output signal function is controlled by the PA3
data register and the timer/event counter state. The
PFD output signal frequency is also dependent on the
timer/event counter overflow period. The definitions of
PFD control signal and PFD output frequency are listed
in the following table.
C O M
X
0
U
X
1
0
X
ON
N
0
PFD
fINT/
[2´(256-N)]
ON
N
1
0
X
Note:
4 2 H
4 3 H
6 6 H
6 7 H
6 8 H
B it
0
1
1
2
2
3
3
X
OFF
4 1 H
0
Timer
PA3 Data PA3 Pad
PFD
Timer Preload
Register
State
Frequency
Value
OFF
4 0 H
S E G M E N T
0
1
2
3
3 8
3 9
4 0
Display Memory
²X² stands for unused
²U² stands for unknown
²256² is for TMR0. If TMR1 is used to generate
PFD, the number should be ²65536².
Rev. 2.00
20
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
LCD Driver Output
LCD bias power supply selection for HT49R70A-1/
HT49C70-1: There are two types of selections: 1/2 bias
or 1/3 bias.
The output number of the LCD driver device can be
41´2, 41´3 or 40´4 by option (i.e., 1/2 duty, 1/3 duty or
1/4 duty). The bias type LCD driver can be ²R² type or
²C² type for HT49R70A-1/HT49C70-1 while the bias
type LCD driver can only be ²C² type for HT49C70L. If
the ²R² bias type is selected, no external capacitor is required. If the ²C² bias type is selected, a capacitor
mounted between C1 and C2 pins is needed. The LCD
driver bias voltage for HT49R70A-1/HT49C70-1 can be
1/2 bias or 1/3 bias by option, while the LCD driver bias
voltage for HT49C70L can only be 1/2 bias. If 1/2 bias is
selected, a capacitor mounted between V2 pin and
ground is required. If 1/3 bias is selected, two capacitors
are needed for V1 and V2 pins.
LCD bias type selection for HT49R70A-1/HT49C70-1:
This option is to determine what kind of bias is selected,
R type or C type.
Low Voltage Reset/Detector Functions
There is a low voltage detector (LVD) and a low voltage
reset circuit (LVR) implemented in the microcontroller.
These two functions can be enabled/disabled by options. Once the options of LVD is enabled, the user can
use the RTCC.3 to enable/disable (1/0) the LVD circuit
and read the LVD detector status (0/1) from RTCC.5;
otherwise, the LVD function is disabled.
D u r in g a r e s e t p u ls e
V A
C O M 0 ,C O M 1 ,C O M 2
V B
V S S
V A
V B
V S S
A ll L C D d r iv e r o u tp u ts
N o r m a l o p e r a tio n m o d e
*
*
*
C O M 0
C O M 1
C O M 2 *
L C D s e g m e n ts O N
C O M 0 ,1 ,2 s id e s a r e u n lig h te d
O n ly L C D s e g m e n ts O N
C O M 0 s id e a r e lig h te d
O n ly L C D s e g m e n ts O N
C O M 1 s id e a r e lig h te d
O n ly L C D s e g m e n ts O N
C O M 2 s id e a r e lig h te d
L C D s e g m e n ts O N
C O M 0 ,1 s id e s a r e lig h te d
L C D s e g m e n ts O N
C O M 0 , 2 s id e s a r e lig h te d
L C D s e g m e n ts O N
C O M 1 ,2 s id e s a r e lig h te d
L C D s e g m e n ts O N
C O M 0 ,1 ,2 s id e s a r e lig h te d
H A L T M o d e
A ll L C D d r iv e r o u tp u ts
Rev. 2.00
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
V A
V B
V S
S
S
S
S
S
S
S
S
S
S
S
V A
V B
V S S
V A
V B
V S S
C O M 0 ,C O M 1 ,C O M 2 *
N o te :
V A
" * " O m it th e C O M 2 s ig n a l, if th e 1 /2 d u ty L C D is u s e d .
V A = V L C D , V B = 1 /2 V L C D fo r H T 4 9 R 7 0 A -1 /H T 4 9 C 7 0 -1
V A = 2 V 2 , V B = V 2 , C ty p e fo r H T 4 9 C 7 0 L
LCD Driver Output (1/3 Duty, 1/2 Bias, R/C Type)
21
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
V A
V B
V C
C O M 0
V S S
V A
V B
V C
C O M 1
V S S
V A
V B
V C
C O M 2
V S S
V A
V B
C O M 3
V C
V S S
V A
V B
V C
L C D s e g m e n ts O N
C O M 2 s id e lig h te d
V S S
N o te : 1 /4 d u ty , 1 /3 b ia s , C
ty p e : " V A " 3 /2 V L C D , " V B " V L C D , " V C " 1 /2 V L C D
1 /4 d u ty , 1 /3 b ia s , R
ty p e : "V A " V L C D , "V B " 2 /3 V L C D , "V C " 1 /3 V L C D
1 /3 b ia s o n ly fo r H T 4 9 R 7 0 A - 1 /H T 4 9 C 7 0 - 1
LCD Driver Output
The LVR has the same effect or function with the external RES signal which performs chip reset. During HALT state,
LVR is disabled.
The RTCC register definitions are listed in the table on the next page.
Bit No.
Label
Read/Write Reset
Function
0~2
RT0~RT2
R/W
111B
3
LVDC*
R/W
0
LVD enable/disable (1/0)
4
QOSC
R/W
0
32768Hz OSC quick start-up oscillation
0/1: quickly/slowly start
5
LVDO*
R
0
LVD detection output (1/0)
1: low voltage detected
6, 7
¾
¾
¾
Unused bit, read as ²0²
8 to 1 multiplexer control inputs to select the real clock prescaler output
Note: ²*² For HT49R70A-1/HT49C70-1
RTCC (09H) Register
Rev. 2.00
22
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Options
The following shows the options in the device. All these options should be defined in order to ensure proper functioning
system.
Options
OSC type selection.
This option is to determine whether an RC or crystal or 32768Hz crystal oscillator is chosen as system clock.
WDT Clock source selection.
RTC and Time Base. There are three types of selections: system clock/4 or RTC OSC or WDT OSC.
WDT enable/disable selection.
WDT can be enabled or disabled by options.
CLR WDT times selection.
This option defines the method to clear the WDT by instruction. ²One time² means that the ²CLR WDT² can clear the
WDT. ²Two times² means that if both of the ²CLR WDT1² and ²CLR WDT2² have been executed, only then will the
WDT be cleared.
Time Base time-out period selection.
The Time Base time-out period ranges from clock/212 to clock/215 ²Clock² means the clock source selected by options.
Buzzer output frequency selection.
There are eight types of frequency signals for buzzer output: Clock/22~Clock/29. ²Clock² means the clock source selected by options.
Wake-up selection.
This option defines the wake-up capability. External I/O pins (PA only) all have the capability to wake-up the chip
from a HALT by a falling edge.
Pull-high selection.
This option is to decide whether the pull-high resistance is visible or not on the PA0~PA3 and PC. (PB and PA4~PA7
are always pull-high)
PA0~PA3 and PC0~PC7 CMOS or NMOS selection.
The structure of PA0~PA3 and PC0~PC7 can be selected as CMOS or NMOS individually. When the CMOS is selected, the related pins only can be used for output operations. When the NMOS is selected, the related pins can be
used for input or output operations. (PA4~PA7 are always NMOS)
Clock source selection of Timer/Event Counter 0. There are two types of selections: system clock or system clock/4.
Clock source selection of Timer/Event Counter 1. There are three types of selections: TMR0 overflow, system clock
or Time Base overflow.
I/O pins share with other function selections.
PA0/BZ, PA1/BZ: PA0 and PA1 can be set as I/O pins or buzzer outputs.
PA3/PFD: PA3 can be set as I/O pins or PFD output.
LCD common selection.
There are three types of selections: 2 common (1/2 duty) or 3 common (1/3 duty) or 4 common (1/4 duty). If the 4
common is selected, the segment output pin ²SEG40² will be set as a common output.
LCD bias power supply selection
There are two types of selections: 1/2 bias or 1/3 bias for HT49R70A-1/HT49C70-1.
LCD bias type selection
This option is to determine what kind of bias is selected, R type or C type for HT49R70A-1/HT49C70-1.
LCD driver clock selection. There are seven types of frequency signals for the LCD driver circuits: fS/22~fS/28. ²fS²
stands for the clock source selection by options.
LCD ON/OFF at HALT selection
LVR selection.
LVR has enable or disable options
LVD selection.
LVD has enable or disable options
PFD selection
If PA3 is set as PFD output, there are two types of selections; One is PFD0 as the PFD output, the other is PFD1 as
the PFD output. PFD0, PFD1 are the timer overflow signals of the Timer/Event Counter 0, Timer/Event Counter 1 respectively.
Rev. 2.00
23
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Application Circuits
For HT49R70A-1/HT49C70-1 Application Circuit
V
D D
0 .0 1 m F *
V D D
C O M 0 ~ C O M 3
S E G 0 ~ S E G 3 9
L C D
P A N E L
1 0 0 k W
0 .1 m F
R E S
1 0 k W
0 .1 m F *
V S S
V L C D
L C D
P o w e r S u p p ly
C 1
0 .1 m F
C 2
O S C
C ir c u it
O S C 1
D D
4 7 0 p F
0 .1 m F
O S C 2
R
O S C
V 2
S e e r ig h t s id e
3 2 7 6 8 H z
V
V 1
0 .1 m F
O S C 3
1 0 p F
O S C 4
O S C 1
fS
C 1
P A 0 ~ P A 7
R 1
P C 0 ~ P C 7
IN T 0
Y S
/4
O S C 2
O S C 1
C 2
P B 0 ~ P B 7
R C S y s te m O s c illa to r
2 4 k W < R O S C < 1 M k W
C ry s ta l S y s te m
F o r th e v a lu e s ,
s e e ta b le b e lo w
O S C 2
O S C 1
IN T 1
T M R 0
3 2 7 6 8 H z C ry s ta l S y s te m
O s c illa to r
O S C 1 a n d O S C 2 le ft
u n c o n n e c te d
O S C 2
T M R 1
H T 4 9 R 7 0 A -1 /H T 4 9 C 7 0 -1
O s c illa to r
O S C
C ir c u it
The following table shows the C1, C2 and R1 values corresponding to the different crystal values. (For reference only)
C1, C2
R1
4MHz Crystal
Crystal or Resonator
0pF
10kW
4MHz Resonator
10pF
12kW
3.58MHz Crystal
0pF
10kW
3.58MHz Resonator
25pF
10kW
2MHz Crystal & Resonator
25pF
10kW
1MHz Crystal
35pF
27kW
480kHz Resonator
300pF
9.1kW
455kHz Resonator
300pF
10kW
429kHz Resonator
300pF
10kW
The function of the resistor R1 is to ensure that the oscillator will switch off should low voltage conditions occur. Such a low voltage, as mentioned here, is one which is less than the lowest value of the
MCU operating voltage. Note however that if the LVR is enabled then R1 can be removed.
Note:
The resistance and capacitance for reset circuit should be designed in such a way as to ensure that the VDD is
stable and remains within a valid operating voltage range before bringing RES to high.
²*² Make the length of the wiring, which is connected to the RES pin as short as possible, to avoid noise
interference.
Rev. 2.00
24
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
For HT49C70L Application Circuit
O S C 3
C O M 0 ~ C O M 3
S E G 0 ~ S E G 3 9
L C D
P A N E L
V
O S C 4
4 7 0 p F
V L C D
0 .1 m F
V
R
D D
0 .1 m F
1 0 0 k W
V
O S C 1
P B 0 ~ P B 7
P C 0 ~ P C 7
C ry s ta l S y s te m
O s c illa to r
D D
O S C 2
H T 4 9 C 7 0 L
Note:
O S C 2
P A 0 ~ P A 7
T M R 1
O s c illa to r
< 1 M W
O S C 2
IN T 0
T M R 0
S C
2 0 0 p F
0 .1 m F
V 2
/4
R C S y s te m
5 6 0 k W < R O
D D
O S C 1
V 1
0 .1 m F
Y S
O S C 1
2 0 0 p F
C 2
R E S
V
O S C
fS
C 1
IN T 1
D D
O S C
3 2
O s
O S
u n
7 6 8 H z C ry s ta l S y s te m
c illa to r
C 1 a n d O S C 2 le ft
c o n n e c te d
C ir c u it
The resistance and capacitance for reset circuit should be designed in such a way as to ensure that the VDD is
stable and remains within a valid operating voltage range before bringing RES to high.
Rev. 2.00
25
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Instruction Set Summary
Description
Instruction
Cycle
Flag
Affected
Add data memory to ACC
Add ACC to data memory
Add immediate data to ACC
Add data memory to ACC with carry
Add ACC to data memory with carry
Subtract immediate data from ACC
Subtract data memory from ACC
Subtract data memory from ACC with result in data memory
Subtract data memory from ACC with carry
Subtract data memory from ACC with carry and result in data memory
Decimal adjust ACC for addition with result in data memory
1
1(1)
1
1
1(1)
1
1
1(1)
1
1(1)
1(1)
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
C
1
1
1
1(1)
1(1)
1(1)
1
1
1
1(1)
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment data memory with result in ACC
Increment data memory
Decrement data memory with result in ACC
Decrement data memory
1
1(1)
1
1(1)
Z
Z
Z
Z
Rotate data memory right with result in ACC
Rotate data memory right
Rotate data memory right through carry with result in ACC
Rotate data memory right through carry
Rotate data memory left with result in ACC
Rotate data memory left
Rotate data memory left through carry with result in ACC
Rotate data memory left through carry
1
1(1)
1
1(1)
1
1(1)
1
1(1)
None
None
C
C
None
None
C
C
Move data memory to ACC
Move ACC to data memory
Move immediate data to ACC
1
1(1)
1
None
None
None
Clear bit of data memory
Set bit of data memory
1(1)
1(1)
None
None
Mnemonic
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
AND data memory to ACC
OR data memory to ACC
Exclusive-OR data memory to ACC
AND ACC to data memory
OR ACC to data memory
Exclusive-OR ACC to data memory
AND immediate data to ACC
OR immediate data to ACC
Exclusive-OR immediate data to ACC
Complement data memory
Complement data memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Rev. 2.00
26
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Instruction
Cycle
Flag
Affected
Jump unconditionally
Skip if data memory is zero
Skip if data memory is zero with data movement to ACC
Skip if bit i of data memory is zero
Skip if bit i of data memory is not zero
Skip if increment data memory is zero
Skip if decrement data memory is zero
Skip if increment data memory is zero with result in ACC
Skip if decrement data memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1(2)
1(2)
1(2)
1(2)
1(3)
1(3)
1(2)
1(2)
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read ROM code (current page) to data memory and TBLH
Read ROM code (last page) to data memory and TBLH
2(1)
2(1)
None
None
No operation
Clear data memory
Set data memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of data memory
Swap nibbles of data memory with result in ACC
Enter power down mode
1
1(1)
1(1)
1
1
1
1(1)
1
1
None
None
None
TO,PDF
TO(4),PDF(4)
TO(4),PDF(4)
None
None
TO,PDF
Mnemonic
Description
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
x: Immediate data
m: Data memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Ö: Flag is affected
-: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle
(four system clocks).
(2)
: If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more
cycle (four system clocks). Otherwise the original instruction cycle is unchanged.
(3) (1)
:
(4)
Rev. 2.00
and (2)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the
CLR WDT1 or CLR WDT2 instruction, the TO and PDF are cleared.
Otherwise the TO and PDF flags remain unchanged.
27
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Instruction Definition
ADC A,[m]
Add data memory and carry to the accumulator
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADCM A,[m]
Add the accumulator and carry to data memory
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,[m]
Add data memory to the accumulator
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the accumulator.
Operation
ACC ¬ ACC+[m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADD A,x
Add immediate data to the accumulator
Description
The contents of the accumulator and the specified data are added, leaving the result in the
accumulator.
Operation
ACC ¬ ACC+x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
ADDM A,[m]
Add the accumulator to the data memory
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the data memory.
Operation
[m] ¬ ACC+[m]
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
28
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
AND A,[m]
Logical AND accumulator with data memory
Description
Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
AND A,x
Logical AND immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_AND operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ANDM A,[m]
Logical AND data memory with the accumulator
Description
Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
CALL addr
Subroutine call
Description
The instruction unconditionally calls a subroutine located at the indicated address. The
program counter increments once to obtain the address of the next instruction, and pushes
this onto the stack. The indicated address is then loaded. Program execution continues
with the instruction at this address.
Operation
Stack ¬ Program Counter+1
Program Counter ¬ addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR [m]
Clear data memory
Description
The contents of the specified data memory are cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
29
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
CLR [m].i
Clear bit of data memory
Description
The bit i of the specified data memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
CLR WDT
Clear Watchdog Timer
Description
The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are
cleared.
Operation
WDT ¬ 00H
PDF and TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
0
¾
¾
¾
¾
CLR WDT1
Preclear Watchdog Timer
Description
Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CLR WDT2
Preclear Watchdog Timer
Description
Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution
of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged.
Operation
WDT ¬ 00H*
PDF and TO ¬ 0*
Affected flag(s)
TO
PDF
OV
Z
AC
C
0*
0*
¾
¾
¾
¾
CPL [m]
Complement data memory
Description
Each pin of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa.
Operation
[m] ¬ [m]
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
30
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
CPLA [m]
Complement data memory and place result in the accumulator
Description
Each pin of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa. The complemented result
is stored in the accumulator and the contents of the data memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DAA [m]
Decimal-Adjust accumulator for addition
Description
The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal
carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a
carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored
in the data memory and only the carry flag (C) may be affected.
Operation
If ACC.3~ACC.0 >9 or AC=1
then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC
else [m].3~[m].0 ¬ (ACC.3~ACC.0), AC1=0
and
If ACC.7~ACC.4+AC1 >9 or C=1
then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1
else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
DEC [m]
Decrement data memory
Description
Data in the specified data memory is decremented by 1.
Operation
[m] ¬ [m]-1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
DECA [m]
Decrement data memory and place result in the accumulator
Description
Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]-1
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
31
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
HALT
Enter power down mode
Description
This instruction stops program execution and turns off the system clock. The contents of
the RAM and registers are retained. The WDT and prescaler are cleared. The power down
bit (PDF) is set and the WDT time-out bit (TO) is cleared.
Operation
Program Counter ¬ Program Counter+1
PDF ¬ 1
TO ¬ 0
Affected flag(s)
TO
PDF
OV
Z
AC
C
0
1
¾
¾
¾
¾
INC [m]
Increment data memory
Description
Data in the specified data memory is incremented by 1
Operation
[m] ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
INCA [m]
Increment data memory and place result in the accumulator
Description
Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
JMP addr
Directly jump
Description
The program counter are replaced with the directly-specified address unconditionally, and
control is passed to this destination.
Operation
Program Counter ¬addr
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV A,[m]
Move data memory to the accumulator
Description
The contents of the specified data memory are copied to the accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
32
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
MOV A,x
Move immediate data to the accumulator
Description
The 8-bit data specified by the code is loaded into the accumulator.
Operation
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
MOV [m],A
Move the accumulator to data memory
Description
The contents of the accumulator are copied to the specified data memory (one of the data
memories).
Operation
[m] ¬ACC
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
Program Counter ¬ Program Counter+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
OR A,[m]
Logical OR accumulator with data memory
Description
Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
OR A,x
Logical OR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_OR operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
ORM A,[m]
Logical OR data memory with the accumulator
Description
Data in the data memory (one of the data memories) and the accumulator perform a
bitwise logical_OR operation. The result is stored in the data memory.
Operation
[m] ¬ACC ²OR² [m]
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
33
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
RET
Return from subroutine
Description
The program counter is restored from the stack. This is a 2-cycle instruction.
Operation
Program Counter ¬ Stack
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RET A,x
Return and place immediate data in the accumulator
Description
The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RETI
Return from interrupt
Description
The program counter is restored from the stack, and interrupts are enabled by setting the
EMI bit. EMI is the enable master (global) interrupt bit.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RL [m]
Rotate data memory left
Description
The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RLA [m]
Rotate data memory left and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the
rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ [m].7
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
34
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
RLC [m]
Rotate data memory left through carry
Description
The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RLCA [m]
Rotate left through carry and place result in the accumulator
Description
Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the
carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored
in the accumulator but the contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
RR [m]
Rotate data memory right
Description
The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRA [m]
Rotate right and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving
the rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
RRC [m]
Rotate data memory right through carry
Description
The contents of the specified data memory and the carry flag are together rotated 1 bit
right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
35
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
RRCA [m]
Rotate right through carry and place result in the accumulator
Description
Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces
the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is
stored in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
SBC A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SBCM A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SDZ [m]
Skip if decrement data memory is 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. If the result is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, [m] ¬ ([m]-1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SDZA [m]
Decrement data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. The result is stored in the accumulator but the data memory remains
unchanged. If the result is 0, the following instruction, fetched during the current instruction
execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, ACC ¬ ([m]-1)
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
36
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
SET [m]
Set data memory
Description
Each pin of the specified data memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SET [m]. i
Set bit of data memory
Description
Bit i of the specified data memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZ [m]
Skip if increment data memory is 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a
dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with
the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, [m] ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SIZA [m]
Increment data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the next
instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper
instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, ACC ¬ ([m]+1)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SNZ [m].i
Skip if bit i of the data memory is not 0
Description
If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data
memory is not 0, the following instruction, fetched during the current instruction execution,
is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i¹0
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
37
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
SUB A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the accumulator.
Operation
ACC ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUBM A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the data memory.
Operation
[m] ¬ ACC+[m]+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SUB A,x
Subtract immediate data from the accumulator
Description
The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+x+1
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
Ö
Ö
Ö
Ö
SWAP [m]
Swap nibbles within the data memory
Description
The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged.
Operation
[m].3~[m].0 « [m].7~[m].4
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SWAPA [m]
Swap data memory and place result in the accumulator
Description
The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.3~ACC.0 ¬ [m].7~[m].4
ACC.7~ACC.4 ¬ [m].3~[m].0
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
38
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
SZ [m]
Skip if data memory is 0
Description
If the contents of the specified data memory are 0, the following instruction, fetched during
the current instruction execution, is discarded and a dummy cycle is replaced to get the
proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZA [m]
Move data memory to ACC, skip if 0
Description
The contents of the specified data memory are copied to the accumulator. If the contents is
0, the following instruction, fetched during the current instruction execution, is discarded
and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed
with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
SZ [m].i
Skip if bit i of the data memory is 0
Description
If bit i of the specified data memory is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i=0
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDC [m]
Move the ROM code (current page) to TBLH and data memory
Description
The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved
to the specified data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
TABRDL [m]
Move the ROM code (last page) to TBLH and data memory
Description
The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to
the data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
39
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
XOR A,[m]
Logical XOR accumulator with data memory
Description
Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XORM A,[m]
Logical XOR data memory with the accumulator
Description
Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
XOR A,x
Logical XOR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Rev. 2.00
TO
PDF
OV
Z
AC
C
¾
¾
¾
Ö
¾
¾
40
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Package Information
100-pin QFP (14´20) Outline Dimensions
C
H
D
8 0
G
5 1
I
5 0
8 1
F
A
B
E
3 1
1 0 0
K
a
J
1
Symbol
Rev. 2.00
3 0
Dimensions in mm
Min.
Nom.
Max.
A
18.50
¾
19.20
B
13.90
¾
14.10
C
24.50
¾
25.20
D
19.90
¾
20.10
E
¾
0.65
¾
F
¾
0.30
¾
G
2.50
¾
3.10
H
¾
¾
3.40
I
¾
0.10
¾
J
1
¾
1.40
K
0.10
¾
0.20
a
0°
¾
7°
41
April 24, 2006
HT49R70A-1/HT49C70-1/HT49C70L
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shanghai Sales Office)
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor Inc. (Shenzhen Sales Office)
43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031
Tel: 0755-8346-5589
Fax: 0755-8346-5590
ISDN: 0755-8346-5591
Holtek Semiconductor Inc. (Beijing Sales Office)
Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031
Tel: 010-6641-0030, 6641-7751, 6641-7752
Fax: 010-6641-0125
Holmate Semiconductor, Inc. (North America Sales Office)
46712 Fremont Blvd., Fremont, CA 94538
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright Ó 2006 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 2.00
42
April 24, 2006