52464 Mii Micro (Pick and Place) Photovoltaic Hi Voltage Output Optocoupler HYBRID MICROELECTRONICS PRODUCTS DIVISION Features: Applications: • • • • • • 12V min. / 14V typical output at 25°C Input/Output Isolation Tested to 1000 VDC Mil Temp Range Pick and Place mounting Solderable terminations FET and IGBT drivers DESCRIPTION The 52464 Photovoltaic Optocoupler is designed for Pick and Place applications using solder or conductive epoxy attachment. It is a single channel optocoupler consisting of optically coupled LED light to photovoltaic detector. Each microcoupler is 100% DC tested at 25°C. (+125°C testing or 100% element evaluation available upon request). All couplers are designed to operate over the full military temperature range. The 52464 is optimized for gate drive of FETs and IGBTs requiring full modulation. ABSOLUTE MAXIMUM RATINGS Continuous Input Current ......................................................................................................................................... 30mA Storage Temperature Range ................................................................................................................. -65ºC to +125ºC Operating Temperature ..........................................................................................................................-55ºC to +125ºC Solder Temperature for 10 seconds...................................................................................................................... 300ºC Reverse Input Voltage.............................................................................................................................................6 VDC RECOMMENDED OPERATING CONDITIONS: 52464 Parameter Symbol Min. Max. Units Input Current IF (ON) 1 20 mA Operating Case Temperature TC -55 +125 °C Micro Photovoltaic Optocoupler Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: [email protected] 1/23/04 www.micropac.com Page 1 of 3 ELECTRICAL SPECIFICATIONS TC= 25°C to +125°C unless otherwise specified Parameter Sym. Min. Input Forward Voltage VF 2.2 Input Reverse Breakdown Voltage VR 6 Input-to-Output Capacitance CIO Output open circuit Voltage Vopen Output Voltage Temperature change Vtemp Output short circuit Current Ishort Input-Output Leakage II-O 12 10 Typ.* Max. Units Test Conditions 3.0 VDC IF = 10 mA 40 VDC IR = 100 µA 4 7 pF Inputs and Outputs shorted IF= 10mA 14 V -2.2 mV/°C 15 µA IF=10mA µA RH ≤ 45%, t = 5 s VI-O = 1000 VDC TC = 25°C 1 Notes IF=10 1 Notes: 1. This parameter is measured between both Output terminals shorted together and both Input terminals shorted together. 2. Dot on top of package indicates LED Anode, Pin 1. 3. LED Anode pad Pin 1 is .022±.003” X .025±.003”. Remaining pads are .025±.003” X .025±.003”. Schematic Diagram 52464 Micro Photovoltaic Optocoupler Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: [email protected] 1/23/04 www.micropac.com Page 2 of 3 Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. MICROCIRCUITS PRODUCTS DIVISION • 905 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 E-MAIL: [email protected] 1/23/04 www.micropac.com Page 3 of 3