MLX90242 Linear Hall Effect Sensor Features and Benefits • • • • Small Plastic Package (SOT-23, 4-SIP-VA, TO-92) Quad Switched Hall Plate / Chopper Stabilized Amplifier Ratiometric Output for A/D Interface Low Quiescent Voltage Thermal Drift Applications • • • Linear Position Sensing Rotary Position Sensing Current Sensing Ordering Information Part No. Sensitivity MLX90242LUA-CC03 MLX90242LVA-CC03 MLX90242ESO-B C03 MLX90242ESO-CC03 40 mV/mT (± 500G) 40 mV/mT (± 500G) 15 mV/mT (± 1300G) 40 mV/mT (± 500G) 1. Functional Diagram Voq 2.50 2.50 2.50 2.50 V V V V TC Temp. Range 700 ppm/°C -40C to 150C 700 ppm/°C -40C to 150C -40C to 85C -40C to 85C Package Nb pins UA VA SO SO 3 4 3 3 2. Description VDD Output The MLX90242 is a CMOS Linear Hall Effect sensor IC. It possesses active error correction circuitry which virtually eliminates the offset errors normally associated with analog Hall Effect devices. Chopper Package Pin1 Pin2 Pin 3 Pin4 Slope SOT23 VDD Out VSS Positive UA VDD VSS Out Negative VA VDD n/c VSS 3901090242 Rev. 024 Out Positive The ratiometric output voltage is proportional to the supply voltage. When using the supply voltage as a reference for an A/D converter, fluctuations of +10% in supply voltage will not affect accuracy. For a positive slope, the voltage at the output will increase as a South magnetic field is applied to the branded face of the MLX90242. Conversely, the voltage output will decrease in the presence of a North magnetic field. For a negative slope, the voltage at the output will increase as a North magnetic field is applied to the branded face of the MLX90242. Conversely, the voltage output will decrease in the presence of a South magnetic field. Page 1 of 7 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor TABLE OF CONTENTS FEATURES AND BENEFITS .............................................................................................................. 1 APPLICATIONS ................................................................................................................................. 1 ORDERING INFORMATION ............................................................................................................... 1 1. FUNCTIONAL DIAGRAM ......................................................................................................... 1-1 2. DESCRIPTION ......................................................................................................................... 2-1 3. GLOSSARY OF TERMS .............................................................................................................. 3 4. ABSOLUTE MAXIMUM RATINGS ............................................................................................... 3 5. MLX90242 ELECTRICAL SPECIFICATIONS ................................................................................ 4 6. MLX90242 MAGNETIC SPECIFICATIONS ................................................................................... 4 7. APPLICATIONS INFORMATION.................................................................................................. 5 8. INSTALLATION COMMENTS ...................................................................................................... 5 9. RELIABILITY INFORMATION ...................................................................................................... 5 10. ESD PRECAUTIONS ................................................................................................................... 6 11. PACKAGE INFORMATION.......................................................................................................... 6 3901090242 Rev. 024 Page 2 of 7 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor 3. Glossary of Terms - Gauss, Tesla: Two units to quantify a magnetic flux density. Conversion: 1 mT = 10 Gauss - Voq: Quiescent output voltage. Output voltage for B = 0. 4. Absolute Maximum Ratings Supply Voltage (Over Voltage), VDD 7.0 V Output Current Short to Vdd 5 mA Output Current Short to Vss 0.5 mA Output Pin Short to Vss Pin Infinite Output Over Voltage 8V Operating Temperature Range, TA -40°C to 150°C Storage Temperature Range, TS -55°C to 150°C Maximun Junction Temp, TJ 170°C Magnetic Flux Density Infinite Exceeding the absolute maximum ratings may cause permanent damage. Exposure to absolutemaximum-rated conditions for extended periods may affect device reliability. 3901090242 Rev. 024 Page 3 of 7 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor 5. MLX90242 Electrical Specifications DC Operating Parameters. L: TA = -40 to 150°C, E: T A = -40 to 85°C VDD = 5.0V (Unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Units Supply Voltage VDD Operating 4.5 5.0 5.5 V Supply Current IDD B = 0, VDD = 5V, IOUT = 0 1.8 2.5 4.5 mA Output Current IOUT -1.0 - 0.1 mA Quiescent Output Voltage VOQ VDD = 5V Pull-up = 5 kO, Pull-down = 50 kO B = 0, TA = 25°C 2.4 2.5 2.6 V Output Voltage VOH VDD = 5V, IOUT = -1.0 mA 4.75 Output Voltage VOL VDD = 5V, IOUT = 0.1 mA Response Time tr Vdd=5V,Vout from Voq to VOH/VOL without load V Noise (RMS) Output Resistance ROUT Linearity Error Le 0.25 V 400 800 µS 5 10 mV Ω 20 %Vdd 0.5 6. MLX90242 Magnetic Specifications L: T A = -40 to 150°C, E: T A = -40 to 85°C VDD = 5.0V (Unless otherwise specified) Parameter MLX90242LUA-CC03 MLX90242LVA-CC03 MLX90242ESO-BC03 MLX90242ESO-CC03 ∆ΤVOQ Min -25 Typ Max 25 Min -25 Typ Max 25 Min Min S 33.2 39.0 44.9 35.3 41.5 47.7 11.5 TC S 430 680 930 430 680 930 Symbol Thermal Voq Drift (1) (mV) Sensitivity, TA = 25° C (mV/mT) TC of Sensitivity (ppm/°C) Typ Max +/- 25 (2) 15 17.3 Typ Max +/- 25 (2) 33.2 680 (2) 39.0 44.9 680 (2) (1) B = 0, TA = -40 to 150°C (2) For ESO package, TC of Sensitivity and Thermal Voq Drift are not fully tested and therefore cannot be specified. Characterization and statistic data can be provided by Melexis upon request. 3901090242 Rev. 024 Page 4 of 7 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor 7. Applications Information C1 and C2 values can be trimmed to satisfied EMC requirements according to the environment (PCB, connectors,...). The output rise time is affected for large capacitor C2, depending of the couple R1;C2. Recommended Wiring VDD 8. Installation Comments 3 MLX 90242 1.) Avoid mechanical stress on leads or package. Stress may cause VOQ shift. C1 = 10nF 1 A.) Avoid bending leads at the package interface. B.) Support the leads by clamping, when bending. C.) Avoid gluing device to another material. 2 V OUT R1 = 10 k C2 = 2.5nF This may cause temperature-related stress. 2.) CMOS products are static sensitive devices, please observe ESD precautions. 3.) Observe temperature limits during soldering 9. Reliability Information Melexis devices are classified and qualified regarding suitability for infrared, vapor phase and wave soldering with usual (63/37 SnPb-) solder (melting point at 183degC). The following test methods are applied: IPC/JEDEC J-STD -020A (issue April 1999) Moisture/Reflow Sensitivity Classification For Nonhermetic Solid State Surface Mount Devices CECC00802 (issue 1994) Standard Method For The Specification of Surface Mounting Components (SMDs) of Assessed Quality MIL 883 Method 2003 / JEDE C-STD-22 Test Method B102 Solderability For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. For process using through hole components, a temperature profile of 235 Deg.C during 30 seconds maximum is tolerated. The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Please contact MLX for Ua part used as SMD device. For more information on manufacturability/solderability see quality page at our website: http://www.melexis.com/ 3901090242 Rev. 024 Page 5 of 7 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor 10. ESD Precautions Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 11. Package Information UA Package Dimensions 45o Typical 1.60 1.40 UA Hall Plate / Chip Location 1.95 +/- 0.15 4.30 3.90 0.84 0.63 o Max 5o Typ 5 0.45 0.41 Hall Plate dimension: 0.150x0.150 * 42GA 2053 3.20 2.80 Max 5 1.52+/-0.15 2.64 2.34 o Marked Surface 0.48 0.43 1.75 1.55 0.7 Max All Dimensions in millimeters 0.38 Typical (see note 3) 0.20 0.00 0.41 0.35 2 3 15.0 14.0 Line 2: 1st digit (2) 2nd and 3rd digits(05) 4th digit (3) PINOUT: Pin 1 Pin 2 Pin 3 1.30 1.24 0.50 0.35 0.20 MIN SOT-23 Hall Plate / Chip Location * MARKING: 1&2 Digits (42) = Part Number (90242) 3,4&5 Dgits(951) =Last Lotnumber Digits 3 * 42951 1 VDD GND (Vss) Output 0.41 0.35 2.57 2.51 SOT-23 Package Dimensions 3.00 2.60 = Year (2002) = Week of Year = Last Lotnumber Digit 1.80 1.50 NOTES: 1.) Controlling dimension: mm chip 0.66 0.56 2 0.25 0.10 2.10 1.70 3.10 2.70 0.10 0.00 0.90 0.70 1.30 1.00 2.) Lead thickness after solder plating will be 0.254 mm maximum 3.) Package dimensions exclude molding flash 4.) The end flash shall not exceed 0.127 mm on each side of package 5.) Tolerance is 0.254mm unless otherwise specified Bottom View of Package PINOUT: Pin 1 Pin 2 Pin 3 VDD Outpout GND MLX90242 2 3901090242 Rev. 024 0 +/- 0.15 3 0.80 +/- 0.15 1 NOTES: 1.) Controlling dimension: mm 2.) Leads must be free of flash and plating voids 3.) Leads must not arc toward the rear of package 4.) Package dimensions exclude molding flash 5.) Tolerance is 0.254mm unless otherwise specified * MARKING: Line 1: 1st and 2nd digits (42) = Part Number MLX90242 3rd and 4th digits (GA) = Version number Page 6 of 7 1 Data Sheet Mar/04 MLX90242 Linear Hall Effect Sensor 5.33 5.43 VA Package Dimensions 5.08 5.24 VA Hall Plate / Chip Location 1.88 +/- 0.15 J 1.22 1.32 Hall Plate 0.15 x 0.15 4.50 4.10 2.40 +/- 0.15 3.76 3.86 A B C 45o X 1mm o 242GA * 5 (2x) 0.387 0.289 XXXXXXX o 5 (2x) Marked Surface 3.46 3.79 3.30 3.63 D Reference (0,0) VA F G H 1.0 MAX 1 2 3 0.22 REF A 1.20 1.10 B 0.66 0.61 C 0.29 0.24 D 45o E 0.31 0.18 F 0.60 0.40 G 0.35 0.25 H 0.15 0.0 J 45o 4 15.50 14.50 0.45 0.35 0.387 0.289 MLX 90242 All Dimensions in millimeters E Notes: 1. Pinout: Pin 1 VDD Pin 2 n/c Pin 3 GND Pin 4 Output 2. Controlling dimension: mm . 3. Leads must be free of flash and plating voids. 4. Leads must not arc toward the rear of package. 5. Package dimensions exclude molding flash. 6. Tolerance: +/- 0.254 mm unless otherwise specified. 9. *Marking: Line 1: 1st three digits (242) = Part Number 4th and 5th digits (GA) = Revision Number Line 2: 7 Digits =Lot Number Back Side Marking YYWW =Lot Number =DateCode Go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe and Japan: All other locations: Phone: +32 13 67 0495 E-mail: [email protected] Phone: +1 603 223 2362 E-mail: [email protected] QS9000, VDA6.1 and ISO14001 Certified 3901090242 Rev. 024 Page 7 of 7 Data Sheet Mar/04