ETC 0603ESDA-TR1

0603ESDA-TR, PolySURG™
TR Series ESD Suppressor
Features:
• 0603/1608 foot print
• Ideal ESD protection for high frequency, low voltage applications.
• Exceeds testing requirements outlined in IEC 61000-4-2
• Ultra low capacitance (0.15pF maximum)
• Very low leakage current
• Fast response time
• Bi-directional
• Surface mount
Applications
• Computers & Peripherals
• PDA’s
• High Speed Data Ports
• HDTV Equipment
• Digital Still Cameras
• USB 2.0
• DVD Players
• Digital Camcorders
• IEEE 1394
• A/V Equipment
• MP3 / Multimedia Players
• HDMI
• Satellite Radio
• Set Top Boxes
• DVI
• Cell Phones
• External Storage
• High Speed Ethernet
• DSL Modems
• Infiniband®
Description
Ordering Information
The PolySURG™ 0603ESDA-TR ESD Suppressors
protect valuable high-speed data circuits from ESD
damage without distorting data signals as a result of
Catalog Number
Packaging
0603ESDA-TR1
5,000 pieces in paper tape on
7" (178mm) reel
its ultra-low (0.15pF maximum) capacitance.
Part Ratings and Characteristics:
Performance Characteristics
Units
Min
Typ
Max
Continuous operating voltage
VDC
-
-
24
voltage2
V
-
35
60
V
-
125
-
Clamping
Trigger voltage3
capability4
kV
-
8
15
Capacitance (@ 1 KHz ~ 1.8GHz)
pF
-
-
0.15
Leakage current (@ 12 VDC)
nA
0.01
<0.1
-
Peak current2
A
-
30
45
Operating temperature
°C
-56
+25
+105
ESD pulse withstand 2
# pulses
20
>5001
-
ESD Threat voltage
Notes:
1. Some shifting in characteristics may occur when tested over
several hundred ESD pulses at very rapid rate of 1 pulse per
second or faster.
2. Per IEC 61000-4-2, 30A @ 8kV, level 4, clamp measurement
made 30ns after initiation of pulse, all tests in contact discharge
mode.
3. Trigger measurement made using Transmission Line Pulse
(TLP) method
4. PolySURG™ devices are capable of withstanding up to a 15 kV,
45A ESD pulse. Device ratings are given at 8kV per Note 1,
unless otherwise specified.
0603ESDA-TR, PolySURG™
TR Series ESD Suppressor
Product Dimension
R
Recommended Solder
Pad Outline
(per IPC-SM-782)
H
T
L
0.60 min
(.023 min)
W
EIA Size
L
W
H
T
1.1 ref
(.043 ref)
R
mm (in)
1.60 ± 0.10 0.80 ± 0.10 0.50 ± 0.10 0.30 ± 0.20 0.70 ± 0.10
(.063 ± .004) (.031 ± .004) (.020 ± .004) (.012 ± .008) (.028 ± .004)
0603ESDA
1.0 max
(.039 max)
Tape-and-Reel Specification
4.0±0.1
(.157±.004)
mm (inches)
2.0±0.05
(.079±.002)
B
2.0±0.75
(.079±.030)
3.5±0.05
(.138±.002)
A
8.0±0.30
(.315±.012)
4.0±0.1
(.157±.004)
1.5±0.10
(.059±.004)
Dimension
0603
A
1.90±0.20
(.075±0.008)
B
1.10±0.20
(.043±0.008)
1.75±0.1
(.069±.004)
2.0±0.5
(.080±.020)
178.0±2.0
(7.008±.080)
21±0.8
(.827±.032)
13.0±0.5
(.512±.020)
60.0±1.5
(2.362±.059)
9.0±1.5
(.354±.059)
Environmental Specifications:
• Moisture Resistance per EIA/IS-722 Paragraph 4.4.2. This standard is based upon MIL-STD-202G Method 103B but with temperature and relative humidity at +85°C and 85% RH respectively. Test condition ‘A’ (240Hr) per MIL-STD-202G
• Thermal shock: MIL-STD-202, Method 107G, -55°C to 125°C, 30 min. cycle, 10 cycles
• Vibration: MIL-STD-202F, Method 201A,(10 to 55 to 10 Hz, 1 min. cycle, 2 hrs each in X-Y-Z)
• Chemical resistance: ASTM D-543, 4 hrs @ 40°C, 3 solutions (H2O, detergent solution, defluxer)
• Operating temperature characteristics, measurement at +25°C, +105°C and -56°C
• Full load voltage: 14.4VDC, 18VDC & 24VDC for 1000 hrs, 25°C
• Solder leach resistance and terminal adhesion: Per EIA-576
• Solderability: MIL-STD-202, Method 208 (95% coverage)
0603ESDA-TR, PolySURG™
TR Series ESD Suppressor
Device Marking
ESDA devices are marked on the tape and reel packages, not individually. Since the product is bi-directional and symmetrical, no
orientation marking is required.
Design Consideration
The location in the circuit for the TR series has to be carefully determined. For better performance, the device should be placed
as close to the signal input as possible and ahead of any other component. Due to the high current associated with an ESD
event, it is recommended to use a “0-stub” pad design (pad directly on the signal/data line and second pad directly on common
ground).
Processing Recommendations
The TR series currently has a convex profile on the top surface of the part. This profile is a result of the construction of the deice.
They can be processed using standard pick-and-place equipment. The placement and processing techniques for these devices are
similar to those used for chip resistors and chip capacitors.
Soldering Recommendations
• Compatible with lead and lead-free solder reflow processes
• Peak reflow temperatures and durations:
• IR Reflow = 260°C max for 10 sec. max.
• Wave Solder = 260°C max. for 10 sec. max.
• Recommended IR Reflow Profile:
0603 7/05
© Cooper Electronic
Technologies 2005
Visit us on the Web at www.cooperbussmann.com
[email protected]
1225 Broken Sound Pkwy. NW, Suite F Boca Raton, Florida 33487
Tel: +1-561-998-4100 Toll Free: +1-888-414-2645 Fax: +1-561-241-6640