KINGBRIGHT AM27YC09

SUBMINIATURE SOLID STATE LAMP
Part Number: AM27YC09
Features
Yellow
Description
SUBMINIATURE PACKAGE.
The Yellow source color devices are made with Gallium
WIDE VIEWING ANGLE.
Arsenide Phosphide on Gallium Phosphide Yellow Light
Z-BEND LEAD.
Emitting Diode.
LONG LIFE - SOLID STATE RELIABILITY.
LOW PACKAGE PROFILE.
PACKAGE :1000PCS / REEL.
MOISTURE SENSITIVITY LEVEL : LEVEL 3.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
5. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAD1333
REV NO: V.5
DATE: MAY/08/2007
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.L.LI
PAGE: 1 OF 5
ERP: 1202000439
Selection Guide
Part No.
Dice
AM27YC09
Lens Type
Yellow (GaAsP/GaP)
WATER CLEAR
Iv (mcd) [2]
@ 20mA
Viewing
Angle [1]
Min.
Typ.
2=1/2
10
30
20°
Notes:
1. ?1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
2. Luminous intensity/ luminous Flux: +/-15%.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
Fpeak
Peak Wavelength
Yellow
FD [1]
Dominant Wavelength
KF1/2
Max.
Units
Test Conditions
590
nm
IF=20mA
Yellow
588
nm
IF=20mA
Spectral Line Half-width
Yellow
35
nm
IF=20mA
C
Capacitance
Yellow
20
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Yellow
2.1
2.5
V
IF=20mA
IR
Reverse Current
Yellow
10
uA
VR=5V
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
Absolute Maximum Ratings at TA=25°C
Parameter
Yellow
Units
Power dissipation
75
mW
DC Forward Current
30
mA
Peak Forward Current [1]
140
mA
5
V
Reverse Voltage
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAD1333
REV NO: V.5
DATE: MAY/08/2007
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.L.LI
PAGE: 2 OF 5
ERP: 1202000439
Yellow
AM27YC09
SPEC NO: DSAD1333
REV NO: V.5
DATE: MAY/08/2007
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.L.LI
PAGE: 3 OF 5
ERP: 1202000439
AM27YC09
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Tape Specifications
(Units : mm)
SPEC NO: DSAD1333
REV NO: V.5
DATE: MAY/08/2007
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.L.LI
PAGE: 4 OF 5
ERP: 1202000439
PACKING & LABEL SPECIFICATIONS
AM27YC09
SPEC NO: DSAD1333
REV NO: V.5
DATE: MAY/08/2007
APPROVED: WYNEC
CHECKED: Allen Liu
DRAWN: Y.L.LI
PAGE: 5 OF 5
ERP: 1202000439