3.0mmx1.5mm SMD CHIP LED LAMP Part Number: APL3015MGC-F01 Mega Green Features Description z 3.0mmx1.5mm SMT LED, 1.4mm THICKNESS. The Mega Green source color devices are made with DH z LOW POWER CONSUMPTION. InGaAlP on GaAs substrate Light Emitting Diode. z WIDE VIEWING ANGLE. z IDEAL FOR BACKLIGHT AND INDICATOR. z VARIOUS COLORS AND LENS TYPES AVAILABLE. z PACKAGE : 2000PCS / REEL. z MOISTURE SENSITIVITY LEVEL : LEVEL 3. z RoHS COMPLIANT. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. Specifications are subject to change without notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAG2041 REV NO: V.2 DATE: MAY/07/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 1 OF 5 ERP: 1203001581 Selection Guide Part No. Dice APL3015MGC-F01 Lens Type Mega Green (InGaAlP) WATER CLEAR Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 2θ1/2 70 140 70° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. 2. Luminous intensity/ luminous Flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Mega Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 574 nm IF=20mA Mega Green 568 nm IF=20mA Spectral Line Half-width Mega Green 26 nm IF=20mA C Capacitance Mega Green 20 pF VF=0V;f=1MHz VF [2] Forward Voltage Mega Green 2.1 2.5 V IF=20mA IR Reverse Current Mega Green 10 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Mega Green Units Power dissipation 75 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAG2041 REV NO: V.2 DATE: MAY/07/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 2 OF 5 ERP: 1203001581 Mega Green APL3015MGC-F01 SPEC NO: DSAG2041 REV NO: V.2 DATE: MAY/07/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 3 OF 5 ERP: 1203001581 APL3015MGC-F01 Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAG2041 REV NO: V.2 DATE: MAY/07/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 4 OF 5 ERP: 1203001581 PACKING & LABEL SPECIFICATIONS APL3015MGC-F01 SPEC NO: DSAG2041 REV NO: V.2 DATE: MAY/07/2007 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.L.LI PAGE: 5 OF 5 ERP: 1203001581